Graphene and biochar-based cathode catalysts for microbial fuel cell: Performance evaluation, economic comparison, environmental and future perspectives.

Microbial fuel cells (MFCs) have been the prime focus of research in recent years because of their distinctive feature of concomitantly treating and producing electricity from wastewater. Nevertheless, the electrical performance of MFCs is hindered by a protracted oxygen reduction reaction (ORR), and often a catalyst is required to boost the cathodic reactions. Conventional transition metals-based catalysts are expensive and infeasible for field-scale usage. In this regard, carbon-based electrocatalysts like waste-derived biochar and graphene are used to enhance the commercialisation prospects of MFC technology. These carbon-catalysts possess unique properties like superior electrocatalytic activity, higher surface area, and high porosity conducive to ORR. Theoretically, graphene-based cathode catalysts yield superior results than a biochar-derived catalyst, though at a higher cost. In contrast, the synthesis of waste-extracted biochar is economical; however, its ability to catalyse ORR is debatable. Therefore, this review aims to make a side-by-side techno-economic assessment of biochar and graphene-based cathode catalyst used in MFC to predict the relative performance and typical cost of power recovery. Additionally, the life cycle analysis of the graphene and biochar-based materials has been briefly discussed to comprehend the associated environmental impacts and overall sustainability of these carbo-catalysts.

Utilisation of waste medicine wrappers as an efficient low-cost electrode material for microbial fuel cell.

Waste generation from healthcare facilities now has become a concerning issue as it contain plastic and metals. Medicine wrappers are one of the major portions of healthcare solid waste, which impel intensive solid waste management practice due to fewer possibilities of deriving by-products. However, it can be recycled and used as an electrode material in microbial fuel cells (MFCs). An electrode material for application in MFCs is a crucial component, which governs total fabrication cost as well as power recovery, thus a cost-effective, stable and durable electrode is essential. In this endeavour, a new metallic (aluminium) waste material, a waste medicine wrapper (WMW), was evaluated for feasibility to be used as anode/cathode in MFCs. Based on the stability test under corrosive environment (1 N KCl), the WMW electrode sustained a maximum current of 46 mA during cyclic voltammetry (CV) and noted only 14% reduction in current at an applied voltage of +0.4 V after 2500 s in chronoamperometry, indicating its good stability. Power recovery from MFC using WMW was higher than the MFC using bare carbon felt as an anode (27 vs. 21 mW/m2). The entire analytical test results viz. CV, electrochemical impedance spectroscopy and power performance established WMW as an excellent anode rather than cathode material.

Sewage treatment in integrated system of UASB reactor and duckweed pond and reuse for aquaculture.

The performance of a laboratory-scale upflow anaerobic sludge blanket (UASB) reactor and a duckweed pond containing Lemna gibba was investigated for suitability for treating effluent for use in aquaculture. While treating low-strength sewage having a chemical oxygen demand (COD) of typically less than 200 mg/L, with an increase in hydraulic retention time (HRT) from 10.04 to 33.49 h, COD removal efficiency of the UASB reactor decreased owing to a decrease in organic loading rate (OLR) causing poor mixing in the reactor. However, even at the lower OLR (0.475 kg COD/(m3 x d)), the UASB reactor gave a removal efficiency of 68% for COD and 74% for biochemical oxygen demand (BOD). The maximum COD, BOD, ammonia-nitrogen and phosphate removal efficiencies of the duckweed pond were 40.77%, 38.01%, 61.87% and 88.57%, respectively. Decreasing the OLR by increasing the HRT resulted in an increase in efficiency of the duckweed pond for removal of ammonia-nitrogen and phosphate. The OLR of 0.005 kg COD/(m2 x d) and HRT of 108 h in the duckweed pond satisfied aquaculture quality requirements. A specific growth rate of 0.23% was observed for tilapia fish fed with duckweed harvested from the duckweed pond. The economic analysis proved that it was beneficial to use the integrated system of a UASB reactor and a duckweed pond for treatment of sewage.

Electricity generation in low cost microbial fuel cell made up of earthenware of different thickness.

Performance of four microbial fuel cells (MFC-1, MFC-2, MFC-3 and MFC-4) made up of earthen pots with wall thicknesses of 3, 5, 7 and 8.5 mm, respectively, was evaluated. The MFCs were operated in fed batch mode with synthetic wastewater having sucrose as the carbon source. The power generation decreased with increase in the thickness of the earthen pot which was used to make the anode chamber. MFC-1 generated highest sustainable power density of 24.32 mW/m(2) and volumetric power of 1.04 W/m(3) (1.91 mA, 0.191 V) at 100 Ω external resistance. The maximum Coulombic efficiencies obtained in MFC-1, MFC-2, MFC-3 and MFC-4 were 7.7, 7.1, 6.8 and 6.1%, respectively. The oxygen mass transfer and oxygen diffusion coefficients measured for earthen plate of 3 mm thickness were 1.79 × 10(-5) and 5.38 × 10(-6) cm(2)/s, respectively, which implies that earthen plate is permeable to oxygen as other polymeric membranes. The internal resistance increased with increase in thickness of the earthen pot MFCs. The thickness of the earthen material affected the overall performance of MFCs.

Performance evaluation of low cost microbial fuel cell fabricated using earthen pot with biotic and abiotic cathode.

An attempt has been made to produce low cost MFC from the commercially available earthen pots in India, without involving any costly membrane. This MFC gave a maximum power output of 16.8 W/m(3) at a Coulombic efficiency (CE) of 31.3% with graphite plate cathode. With stainless steel mesh cathode and KMnO(4) as cathodic electrolyte the power production and CE of 70.48 W/m(3) and 64.5%, respectively, was obtained. The performance of this earthen pot MFC was evaluated with biotic and abiotic cathode. Although, biofilm formation on the cathode is observed to be helpful in enhancing power out put, the thicker biofilm on the cathode showed reduction in power. This MFC demonstrated competitive performance as compared to MFC incorporated with membrane. This low cost MFC, with total production cost of less than 1.0$, as per Indian market, demonstrated its utility as a wastewater treatment and onsite power generation device.

Sewage reuse for aquaculture after treatment in oxidation and duckweed pond.

The benefits of treating sewage by pond systems offer, through a simple and low-cost technology, social and commercial benefits, from the waste raw materials. The objective of this work was to demonstrate an effective treatment of the sewage by using natural treatment systems, and use of treated wastewater for aquaculture. The study was conducted for the sewage generated from the IIT Kharagpur campus. After characterization of the sewage, laboratory scale experiments were conducted for treatment using oxidation pond and duckweed pond. Survival and growth of fishes were observed in the experimental ponds using treated sewage. Based on the experimental results, full-scale treatment plant was designed to meet the aquaculture water quality. From the economics of the proposed full-scale plant, and utilization of the treated sewage for aquaculture, it is estimated that, the amount of Rs. 20,0000 can be generated every year. This amount recovered from the aquaculture will be more than the operating cost of the treatment plant, hence, making the operation of sewage treatment plant self sufficient. Use of a UASB reactor as the first stage treatment before sewage passes to the oxidation pond, can be a more attractive alternative because of less land requirement as compared to the oxidation pond alone, and additional land can be made available for aquaculture to increase revenue.