Mechanical assessment of arterial dissection in health and disease: Advancements and challenges.

Arterial dissection involves a complex series of coupled biomechanical events. The past two decades have witnessed great advances in the understanding of the intrinsic mechanism for dissection initiation, and hence in the development of novel therapeutic strategies for surgical repair. This is due in part to the profound advancements in characterizing emerging behaviors of dissection using state-of-the-art tools in experimental and computational biomechanics. In addition, researchers have identified the important role of the microstructure in determining the tissue׳s fracture modality during dissection propagation. In this review article, we highlight a variety of approaches in terms of biomechanical measurements, computational modeling and histological/microstructural analysis used to characterize a dissection that propagates in healthy and diseased arteries. Notable findings with quantitative mechanical data are reviewed. We conclude by discussing some unsolved problems that are of interest for future research.

Quantitative assessment of collagen fibre orientations from two-dimensional images of soft biological tissues.

In this work, we outline an automated method for the extraction and quantification of material parameters characterizing collagen fibre orientations from two-dimensional images. Morphological collagen data among different length scales were obtained by combining the established methods of Fourier power spectrum analysis, wedge filtering and progressive regions of interest splitting. Our proposed method yields data from which we can determine parameters for computational modelling of soft biological tissues using fibre-reinforced constitutive models and gauge the length scales most appropriate for obtaining a physically meaningful measure of fibre orientations, which is representative of the true tissue morphology of the two-dimensional image. Specifically, we focus on three parameters quantifying different aspects of the collagen morphology: first, using maximum-likelihood estimation, we extract location parameters that accurately determine the angle of the principal directions of the fibre reinforcement (i.e. the preferred fibre directions); second, using a dispersion model, we obtain dispersion parameters quantifying the collagen fibre dispersion about these principal directions; third, we calculate the weighted error entropy as a measure of changes in the entire fibre distributions at different length scales, as opposed to their average behaviour. With fully automated imaging techniques (such as multiphoton microscopy) becoming increasingly popular (which often yield large numbers of images to analyse), our method provides an ideal tool for quickly extracting mechanically relevant tissue parameters which have implications for computational modelling (e.g. on the mesh density) and can also be used for the inhomogeneous modelling of tissues.

Call for standards in technical documentation of intracoronary stents.

At present, the product information of intracoronary stents provided by the industry contains only limited technical data restricting judgments on the in vivo performance of individual products. Available experimental and clinical evidence suggests that interventional target sites display highly heterogeneous biomechanical behavior needed to be matched by specific stent and stent delivery system characteristics. To allow individualized stent-lesion matching, both, understanding of biomechanical properties of the atherosclerotic coronary artery lesions and expert knowledge of the intracoronary stent systems, are required. Here, the authors review some of the initial data on mechanical properties of coronary artery lesions potentially relevant to stenting and suggest standards for technical documentation of intracoronary stents.

Assessment of the in vivo biomechanical properties of the human uterine cervix in pregnancy using the aspiration test: a feasibility study.

OBJECTIVE: To date no diagnostic tool is yet available to objectively assess the in vivo biomechanical properties of the uterine cervix during gestation. METHODS: We show the first clinical application of an aspiration device to assess the in vivo biomechanical properties of the cervix in pregnancy with the aim to describe the physiological biomechanical changes throughout gestation in order to eventually detect pregnant women at risk for cervical insufficiency (CI). RESULTS: Out of 15 aspiration measurements, 12 produced valid results. The stiffness values were in the range between 0.013 and 0.068 bar/mm. The results showed a good reproducibility of the aspiration test. In our previous test series on non-pregnant cervices our repetitive measurements showed a standard deviation of >20% compared to <+/-10% to our data on pregnant cervices. Stiffness values are decreasing with gestational age which indicates a progressive softening of cervical tissue towards the end of pregnancy. Three pregnant women had two subsequent measurements within a time interval of four weeks. Decreasing stiffness values in the range of 20% were recorded. DISCUSSION: This preliminary study on the clinical practicability of aspiration tests showed promising results in terms of reproducibility (reliability) and clinical use (feasibility). Ongoing studies will provide further insights on its usefulness in clinical practice and in the detection of substantial changes of the cervix in pregnancy indicative for threatened preterm birth or cervical insufficiency.

Changes in the mechanical environment of stenotic arteries during interaction with stents: computational assessment of parametric stent designs.

Clinical studies have identified factors such as the stent design and the deployment technique that are one cause for the success or failure of angioplasty treatments. In addition, the success rate may also depend on the stenosis type. Hence, for a particular stenotic artery, the optimal intervention can only be identified by studying the influence of factors such as stent type, strut thickness, geometry of the stent cell, and stent-artery radial mismatch with the wall. We propose a methodology that allows a set of stent parameters to be varied, with the aim of evaluating the difference in the mechanical environment within the wall before and after angioplasty with stenting. Novel scalar quantities attempt to characterize the wall changes inform of the contact pressure caused by the stent struts, and the stresses within the individual components of the wall caused by the stent. These quantities are derived numerically and serve as indicators, which allow the determination of the correct size and type of the stent for each individual stenosis. In addition, the luminal change due to angioplasty may be computed as well. The methodology is demonstrated by using a full three-dimensional geometrical model of a postmortem specimen of a human iliac artery with a stenosis using imaging data. To describe the material behavior of the artery, we considered mechanical data of eight different vascular tissues, which formed the stenosis. The constitutive models for the tissue components capture the typical anisotropic, nonlinear and dissipative characteristics under supra-physiological loading conditions. Three-dimensional stent models were parametrized in such a way as to enable new designs to be generated simply with regard to variations in their geometric structure. For the three-dimensional stent-artery interaction we use a contact algorithm based on smooth contact surfaces of at least C-continuity, which prevents numerical problems known from standard facet-based contact algorithm. The proposed methodology has the potential to provide a scientific basis for optimizing treatment procedures and stent geometries and materials, to help stent designers examine new stent designs "virtually," and to assist clinicians in choosing the most suitable stent for a particular stenosis.