A percutaneous approach to create tricuspid regurgitation in swine: a model for transcatheter tricuspid valve therapy assessment.

PURPOSE: The purpose of this study was to develop a simple and effective percutaneous approach to create tricuspid regurgitation in swine. METHODS: Eleven pigs (71.68 ± 7.70 kg, 3 male) were involved in this study. A grasping forceps was introduced into the right ventricle through a steerable sheath under fluoroscopic guidance and used to disrupt the tricuspid valve apparatus by avulsing leaflet or chordae tendineae repeatedly. Transthoracic echocardiography and right ventricular angiography were used to evaluate the degree of tricuspid regurgitation created. RESULTS: Ten of the 11 pigs (90.91%) achieved severe tricuspid regurgitation and 1 (9.09%) obtained moderate tricuspid regurgitation immediately after the procedure. Heart rate of the pigs significantly increased immediately after tricuspid regurgitation creation compared to baseline (88.64 ± 23.24 vs. 76.00 ± 15.30 bpm, P = 0.02), but recovered to normal level at one month follow-up (77.09 ± 11.97 bpm, P = 0.85). The right atrium, tricuspid valve annulus, and right ventricle dilated obviously one month after tricuspid regurgitation creation (dimension changes: 3.01 ± 0.35 vs. 3.56 ± 0.40 cm, P = 0.02; 2.92 ± 0.36 vs. 3.37 ± 0.39 cm, P = 0.01; 3.06 ± 0.42 vs. 3.60 ± 0.47 cm, P = 0.03 respectively). Autopsy findings showed that rupture of leaflet and/or chordae tendineae finally led to the tricuspid regurgitation. CONCLUSIONS: Severe tricuspid regurgitation can be created by a simple and effective percutaneous approach with a grasping forceps in swine model and right heart dilation can be observed consistently at one-month follow-up. This model will be valuable in pre-clinical studies for developing new tricuspid valve repair or replacement technique to treat severe tricuspid regurgitation.

Design considerations and quantitative assessment for the development of percutaneous mitral valve stent.

Percutaneous heart valve replacement is gaining popularity, as more positive reports of satisfactory early clinical experiences are published. However this technique is mostly used for the replacement of pulmonary and aortic valves and less often for the repair and replacement of atrioventricular valves mainly due to their anatomical complexity. While the challenges posed by the complexity of the mitral annulus anatomy cannot be mitigated, it is possible to design mitral stents that could offer good anchorage and support to the valve prosthesis. This paper describes four new Nitinol based mitral valve designs with specific features intended to address migration and paravalvular leaks associated with mitral valve designs. The paper also describes maximum possible crimpability assessment of these mitral stent designs using a crimpability index formulation based on the various stent design parameters. The actual crimpability of the designs was further evaluated using finite element analysis (FEA). Furthermore, fatigue modeling and analysis was also done on these designs. One of the models was then coated with polytetrafluoroethylene (PTFE) with leaflets sutured and put to: (i) leaflet functional tests to check for proper coaptation of the leaflet and regurgitation leakages on a phantom model and (ii) anchorage test where the stented valve was deployed in an explanted pig heart. Simulations results showed that all the stents designs could be crimped to 18F without mechanical failure. Leaflet functional test results showed that the valve leaflets in the fabricated stented valve coapted properly and the regurgitation leakage being within acceptable limits. Deployment of the stented valve in the explanted heart showed that it anchors well in the mitral annulus. Based on these promising results of the one design tested, the other stent models proposed here were also considered to be promising for percutaneous replacement of mitral valves for the treatment of mitral regurgitation, by virtue of their key features as well as effective crimping. These models will be fabricated and put to all the aforementioned tests before being taken for animal trials.