Regional differences, dynamic evolution, and spatial spillover effects of carbon emission intensity in urban agglomerations.

Taking three major urban agglomerations in China as examples, this paper uses the Dagum Gini coefficient and its decomposition method, a Kernel density estimation method, and Markov chain and spatial Markov chain to study the regional differences, dynamic evolution characteristics, and spatial spillover effects of carbon emission intensity (CEI) of urban agglomerations, and accordingly, it proposes differentiated emission reduction and carbon reduction policies. The following results were obtained: (1) The overall CEI of the three major urban agglomerations and each individual urban agglomeration were found to have declined significantly over time, with an overall spatial pattern of "high in the north and low in the south," with inter-group differences being the main source of the overall differences. (2) The imbalance in CEI between cities was more obvious within the Beijing-Tianjin-Hebei (BTH) urban agglomeration, while the synergistic emission reduction effect of the Yangtze River Delta (YRD) and Pearl River Delta (PRD) urban agglomerations increased over the study period. (3) The probability of a city maintaining a stable level of CEI was much higher than the probability of a state shift, and there was a spatial spillover effect of carbon emissions between neighboring cities. This study can provide theoretical support for the global response to greenhouse gas emissions, promoting green development and carbon reduction in various countries and urban agglomerations and providing a quantitative basis for the formulation of relevant policies.

Assessment of the Defatting Efficacy of Mechanical and Chemical Treatment for Allograft Cancellous Bone and Its Effects on Biomechanics Properties of Bone.

OBJECTIVE: To assess the defatting efficacy of high pressure washing and gradient alcohol and biomechanical properties of defatted bone. METHODS: Fresh cancellous bone was obtained from the femoral condyle and divided into six groups according to different defatting treatments, which were: high pressure washing for 10 s (10S group), 20 s (20S group), and 30 s (30S group), gradient alcohol immersion (Alcohol group), acetone immersion (Acetone group), and non-defatted (Fresh group). The appearance of six groups was observed, and the appearance of defatted bone and fresh bone was compared. The residual lipid content and infrared spectrum were used to compare the efficacy of defatting, the DNA content was used to compare the cell content after defatting, and the maximum stress and elastic modulus were used to compare the effects of defatting treatment on biomechanical properties. RESULTS: The fresh bone was yellow and the pores contained a lot of fat. The defatted bone was white and the porous network was clear. There was no difference in residual lipid content among the three groups with high pressure washing (1.45% ± 0.16%, 1.40% ± 0.13%, and 1.46% ± 0.11%, respectively) (P = 0.828). There was no difference in residual lipid content among the 10S, alcohol, and acetone groups (1.45% ± 0.16%, 1.28% ± 0.07%, and 1.13% ± 0.22%, respectively) (P = 0.125). Infrared spectra showed that the fat content of the five defatting groups was significantly lower than that of the fresh group. There was no difference in residual lipid content among the three groups with high pressure washing (4.53 ± 0.23 ug/mL, 4.61 ± 0.18 ug/mL, and 4.66 ± 0.25 ug/mL, respectively) (P = 0.645). There was no difference in residual lipid content among the 10S, alcohol, and acetone groups (4.53 ± 0.23 ug/mL, 4.29 ± 0.24 ug/mL, and 4.27 ± 0.29 ug/mL, respectively) (P = 0.247). The maximum stress of the bone decreased significantly with the increase of the washing time (9.95 ± 0.31 Mpa, 9.07 ± 0.45 Mpa, and 8.17 ± 0.35 Mpa, respectively) (P = 0.003). The elastic modulus of the bone decreased significantly with the increase of the washing time (116.40 ± 3.54 Mpa, 106.10 ± 5.29 Mpa, and 95.63 ± 4.08 Mpa, respectively) (P = 0.003). There was no statistical difference in the maximum stress between the fresh group, the 10S group, the alcohol group, and the acetone group (10.09 ± 0.67 Mpa, 9.95 ± 0.31 Mpa, 10.11 ± 0.07 Mpa, and 10.09 ± 0.39 Mpa, respectively) (P = 0.963). There was no statistical difference in the maximum stress between the fresh group, the 10S group, the alcohol group and the acetone group (119.93 ± 4.94 Mpa, 116.40 ± 3.54 Mpa, 118.27 ± 0.85 Mpa, 118.10 ± 4.52 Mpa, respectively) (P = 0.737). CONCLUSION: The defatting efficiency was satisfactory at a time of 10 s under high pressure washing. In terms of defatting efficiency and its effect on biomechanical properties of bone, high pressure washing and gradient alcohol were similar to conventional acetone solvent extraction defatting.

High-performance liquid chromatography with fluorescence detection for the determination of nitrofuran metabolites in pork muscle.

A simple and sensitive HPLC method with fluorescence detection (HPLC-FLD) is reported for the simultaneous determination of metabolites of four nitrofuran drugs (furazolidone, furaltadone, nitrofurantoin and nitrofurazone) in pork muscle. The method involves acid hydrolysis of the protein-bound drug metabolites and the conjugation of the released side-chains with a novel fluorescence agent 2-hydroxy-1-naphthaldehyde. After liquid-liquid extraction and effective separation of the derivatives on a YMC-Pack Polymer C18 column at 40°C under alkaline conditions, the high fluorescence intensity of these derivatives at emission wavelength λem = 463 nm enables their simultaneous determination in pork muscle at concentrations as low as 1 µg kg⁻¹. The method was validated using blank pork muscle fortified with all four metabolites at 0.5, 1.0 and 2.0 µg kg⁻¹. Recoveries were > 92.3% with RSDs < 8.5% for all four metabolites. The results obtained with HPLC-FLD and LC-MS/MS methods showed very good agreement for pork muscle samples.