Facile Synthesis and Life Cycle Assessment of Highly Active Magnetic Sorbent Composite Derived from Mixed Plastic and Biomass Waste for Water Remediation.

Plastic and biomass waste pose a serious environmental risk; thus, herein, we mixed biomass waste with plastic bottle waste (PET) to produce char composite materials for producing a magnetic char composite for better separation when used in water treatment applications. This study also calculated the life cycle environmental impacts of the preparation of adsorbent material for 11 different indicator categories. For 1 functional unit (1 kg of pomace leaves as feedstock), abiotic depletion of fossil fuels and global warming potential were quantified as 7.17 MJ and 0.63 kg CO2 equiv for production of magnetic char composite materials. The magnetic char composite material (MPBC) was then used to remove crystal violet dye from its aqueous solution under various operational parameters. The kinetics and isotherm statistical theories showed that the sorption of CV dye onto MPBC was governed by pseudo-second-order, and Langmuir models, respectively. The quantitative assessment of sorption capacity clarifies that the produced MPBC exhibited an admirable ability of 256.41 mg g-1. Meanwhile, the recyclability of 92.4% of MPBC was demonstrated after 5 adsorption/desorption cycles. Findings from this study will inspire more sustainable and cost-effective production of magnetic sorbents, including those derived from combined plastic and biomass waste streams.

Assessment of Lewis-Acidic Surface Sites Using Tetrahydrofuran as a Suitable and Smart Probe Molecule.

Measuring the Lewis-acidic surface sites in catalysis is problematic when the material's surface area is very low (SBET ≤1 m2 ⋅ g-1 ). For the first time, a quantitative assessment of total acidic surface sites of very small surface area catalysts (MoO3 as pure and mixed with 5-30 % CdO (wt/wt), as well as CdO for comparison) was performed using a smart new probe molecule, tetrahydrofuran (THF). The results were nearly identical compared to using another commonly used probe molecule, pyridine. This audition is based on the limited values of the surface area of these samples that likely require a relatively moderate basic molecule as THF with pKb =16.08, rather than strong basic molecules such as NH3 (pKb =4.75) or pyridine (pKb =8.77). We propose mechanisms for the interaction of vapour phase molecules of THF with the Lewis-cationic Mo and Cd atoms of these catalysts. Besides, dehydration of isopropyl alcohol was used as a probe reaction to investigate the catalytic activity of these catalysts to further support our findings in the case of THF in a temperature range of 175-300 °C. A good agreement between the obtained data of sample MoO3 -10 % CdO, which is characterised by the highest surface area value, the population of Lewis-acidic sites and % selectivity of propylene at all the applied reaction temperatures was found.

Integrating life cycle assessment and characterisation techniques: A case study of biodiesel production utilising waste Prunus Armeniaca seeds (PAS) and a novel catalyst.

Prunus Armeniaca seed (PAS) oil was utilised as a waste biomass feedstock for biodiesel production via a novel catalytic system (SrO-La2O3) based on different stoichiometric ratios. The catalysts have been characterised and followed by a parametric analysis to optimise catalyst results. The catalyst with a stoichiometric ratio of Sr: La-8 (Sr-La-C) using parametric analysis showed an optimum yield of methyl esters is 97.28% at 65 °C, reaction time 75 min, catalyst loading 3 wt% and methanol to oil molar ratio of 9. The optimum catalyst was tested using various oil feedstocks such as waste cooking oil, sunflower oil, PAS oil, date seed oil and animal fat. The life cycle assessment was performed to evaluate the environmental impacts of biodiesel production utilising waste PAS, considering 1000 kg of biodiesel produced as 1 functional unit. The recorded results showed the cumulative abiotic depletion of fossil resources over the entire biodiesel production process as 22,920 MJ, global warming potential as 1150 kg CO2 equivalent, acidification potential as 4.89 kg SO2 equivalent and eutrophication potential as 0.2 kg PO43- equivalent for 1 tonne (1000 kg) of biodiesel produced. Furthermore, the energy ratio (measured as output energy divided by input energy) for the entire production process was 1.97. These results demonstrated that biodiesel obtained from the valorisation of waste PAS provides a suitable alternative to fossil fuels.

Techno-economic evaluation of biogas production from food waste via anaerobic digestion.

Food waste is a major constituent in municipal solid wastes and its accumulation or disposal of in landfills is problematic, causing environmental issues. Herein, a techno-economic study is carried out on the potential of biogas production from different types of food waste generated locally. The biogas production tests were at two-time sets; 24-h and 21-day intervals and results showed a good correlation between those two-time sets. Thus, we propose to use the 24-h time set to evaluate feedstock fermentation capacity that is intended for longer periods. Our approach could potentially be applied within industry as the 24-h test can give a good indication of the potential substrate gas production as a quick test that saves time, with minimal effort required. Furthermore, polynomial models were used to predict the production of total gas and methane during the fermentation periods, which showed good matching between the theoretical and practical values with a coefficient of determination R2 = 0.99. At day 21, the accumulative gas production value from mixed food waste samples was 1550 mL per 1 g of dry matter. An economic evaluation was conducted and showed that the case study breaks-even at $0.2944 per cubic metre. Any prices above this rate yield a positive net present value (NPV); at $0.39/m3 a discounted payback period of six years and a positive NPV of $3108 were calculated. If waste management fee savings are to be incorporated, the total savings would be higher, increasing annual cash flows and enhancing financial results. This economic evaluation serves as a preliminary guide to assess the economic feasibility based on the fluctuating value of methane when producing biogas from food waste via anaerobic digestion, thus could help biogas project developers investigate similar scale scenarios .

Assessment of the energy recovery potential of waste Photovoltaic (PV) modules.

Global exponential increase in levels of Photovoltaic (PV) module waste is an increasing concern. The purpose of this study is to investigate if there is energy value in the polymers contained within first-generation crystalline silicon (c-Si) PV modules to help contribute positively to recycling rates and the circular economy. One such thermochemical conversion method that appeals to this application is pyrolysis. As c-Si PV modules are made up of glass, metal, semiconductor and polymer layers; pyrolysis has potential not to promote chemical oxidation of any of these layers to help aid delamination and subsequently, recovery. Herein, we analysed both used polymers taken from a deconstructed used PV module and virgin-grade polymers prior to manufacture to determine if any properties or thermal behaviours had changed. The calorific values of the used and virgin-grade Ethylene vinyl acetate (EVA) encapsulant were found to be high, unchanged and comparable to that of biodiesel at 39.51 and 39.87 MJ.Kg-1, respectively. This result signifies that there is energy value within used modules. As such, this study has assessed the pyrolysis behaviour of PV cells and has indicated the energy recovery potential within the used polymers found in c-Si PV modules.