Practical considerations for using low-cost sensors to assess wildfire smoke exposure in school and childcare settings.

BACKGROUND: More frequent and intense wildfires will increase concentrations of smoke in schools and childcare settings. Low-cost sensors can assess fine particulate matter (PM2.5) concentrations with high spatial and temporal resolution. OBJECTIVE: We sought to optimize the use of sensors for decision-making in schools and childcare settings during wildfire smoke to reduce children's exposure to PM2.5. METHODS: We measured PM2.5 concentrations indoors and outdoors at four schools in Washington State during wildfire smoke in 2020-2021 using low-cost sensors and gravimetric samplers. We randomly sampled 5-min segments of low-cost sensor data to create simulations of brief portable handheld measurements. RESULTS: During wildfire smoke episodes (lasting 4-19 days), median hourly PM2.5 concentrations at different locations inside a single facility varied by up to 49.6 µg/m3 (maximum difference) during school hours. Median hourly indoor/outdoor ratios across schools ranged from 0.22 to 0.91. Within-school differences in concentrations indicated that it is important to collect measurements throughout a facility. Simulation results suggested that making handheld measurements more often and over multiple days better approximates indoor/outdoor ratios for wildfire smoke. During a period of unstable air quality, PM2.5 over the next hour indoors was more highly correlated with the last 10-min of data (mean R2 = 0.94) compared with the last 3-h (mean R2 = 0.60), indicating that higher temporal resolution data is most informative for decisions about near-term activities indoors. IMPACT STATEMENT: As wildfires continue to increase in frequency and severity, staff at schools and childcare facilities are increasingly faced with decisions around youth activities, building use, and air filtration needs during wildfire smoke episodes. Staff are increasingly using low-cost sensors for localized outdoor and indoor PM2.5 measurements, but guidance in using and interpreting low-cost sensor data is lacking. This paper provides relevant information applicable for guidance in using low-cost sensors for wildfire smoke response.

Leveraging low-cost sensors to predict nitrogen dioxide for epidemiologic exposure assessment.

BACKGROUND: Statistical models of air pollution enable intra-urban characterization of pollutant concentrations, benefiting exposure assessment for environmental epidemiology. The new generation of low-cost sensors facilitate the deployment of dense monitoring networks and can potentially be used to improve intra-urban models of air pollution. OBJECTIVE: Develop and evaluate a spatiotemporal model for nitrogen dioxide (NO2) in the Puget Sound region of WA, USA for the Adult Changes in Thought Air Pollution (ACT-AP) study and assess the contribution of low-cost sensor data to the model's performance through cross-validation. METHODS: We developed a spatiotemporal NO2 model for the study region incorporating data from 11 agency locations, 364 supplementary monitoring locations, and 117 low-cost sensor (LCS) locations for the 1996-2020 time period. Model features included long-term time trends and dimension-reduced land use regression. We evaluated the contribution of LCS network data by comparing models fit with and without sensor data using cross-validated (CV) summary performance statistics. RESULTS: The best performing model had one time trend and geographic covariates summarized into three partial least squares components. The model, fit with LCS data, performed as well as other recent studies (agency cross-validation: CV- root mean square error (RMSE) = 2.5 ppb NO2; CV- coefficient of determination ( R 2 ) = 0.85). Predictions of NO2 concentrations developed with LCS were higher at residential locations compared to a model without LCS, especially in recent years. While LCS did not provide a strong performance gain at agency sites (CV-RMSE = 2.8 ppb NO2; CV- R 2 = 0.82 without LCS), at residential locations, the improvement was substantial, with RMSE = 3.8 ppb NO2 and R 2 = 0.08 (without LCS), compared to CV-RMSE = 2.8 ppb NO2 and CV- R 2 = 0.51 (with LCS). IMPACT: We developed a spatiotemporal model for nitrogen dioxide (NO2) pollution in Washington's Puget Sound region for epidemiologic exposure assessment for the Adult Changes in Thought Air Pollution study. We examined the impact of including low-cost sensor data in the NO2 model and found the additional spatial information the sensors provided predicted NO2 concentrations that were higher than without low-cost sensors, particularly in recent years. We did not observe a clear, substantial improvement in cross-validation performance over a similar model fit without low-cost sensor data; however, the prediction improvement with low-cost sensors at residential locations was substantial. The performance gains from low-cost sensors may have been attenuated due to spatial information provided by other supplementary monitoring data.

School and childcare facility air quality decision-makers' perspectives on using low-cost sensors for wildfire smoke response.

BACKGROUND: During wildfire smoke episodes, school and childcare facility staff and those who support them rely upon air quality data to inform activity decisions. Where ambient regulatory monitor data is sparse, low-cost sensors can help inform local outdoor activity decisions, and provide indoor air quality data. However, there is no established protocol for air quality decision-makers to use sensor data for schools and childcare facilities. To develop practical, effective toolkits to guide the use of sensors in school and childcare settings, it is essential to understand the perspectives of the potential end-users of such toolkit materials. METHODS: We conducted 15 semi-structured interviews with school, childcare, local health jurisdiction, air quality, and school district personnel regarding sensor use for wildfire smoke response. Interviews included sharing PM2.5 data collected at schools during wildfire smoke. Interviews were transcribed and transcripts were coded using a codebook developed both a priori and amended as additional themes emerged. RESULTS: Three major themes were identified by organizing complementary codes together: (1) Low-cost sensors are useful despite data quality limitations, (2) Low-cost sensor data can inform decision-making to protect children in school and childcare settings, and (3) There are feasibility and public perception-related barriers to using low-cost sensors. CONCLUSIONS: Interview responses provided practical implications for toolkit development, including demonstrating a need for toolkits that allow a variety of sensor preferences. In addition, participants expected to have a wide range of available time for monitoring, budget for sensors, and decision-making types. Finally, interview responses revealed a need for toolkits to address sensor uses outside of activity decisions, especially assessment of ventilation and filtration.

Wildfire Smoke Monitoring for Agricultural Safety and Health in Rural Washington.

OBJECTIVES: This study aimed to evaluate the performance of a low-cost smoke sampling platform relative to environmental and occupational exposure monitoring methods in a rural agricultural region in central Washington state. METHODS: We co-located the Thingy AQ sampling platform alongside cyclone-based gravimetric samplers, a nephelometer, and an environmental beta attenuation mass (E-BAM) monitor during August and September of 2020. Ambient particulate matter concentrations were collected during a smoke and non-smoke period and measurements were compared across sampling methods. RESULTS: We found reasonable agreement between observations from two particle sensors within the Thingy AQ platform and the nephelometer and E-BAM measurements throughout the study period, though the measurement range of the sensors was greater during the smoke period compared to the non-smoke period. Occupational gravimetric sampling methods did not correlate with PM2.5 data collected during smoke periods, likely due to their capture of larger particle sizes than those typically measured by PM2.5 ambient air quality instruments during wildfire events. CONCLUSION: Data collected before and during an intense wildfire smoke episode in September 2020 indicated that the low-cost smoke sampling platform provides a strategy to increase access to real-time air quality information in rural areas where regulatory monitoring networks are sparse if sensor performance characteristics under wildfire smoke conditions are understood. Improving access to spatially resolved air quality information could help agricultural employers protect both worker and crop health as wildfire smoke exposure increases due to the impacts of climate change. Such information can also assist employers with meeting new workplace wildfire smoke health and safety rules.

Design and evaluation of short-term monitoring campaigns for long-term air pollution exposure assessment.

BACKGROUND: Short-term mobile monitoring campaigns to estimate long-term air pollution levels are becoming increasingly common. Still, many campaigns have not conducted temporally-balanced sampling, and few have looked at the implications of such study designs for epidemiologic exposure assessment. OBJECTIVE: We carried out a simulation study using fixed-site air quality monitors to better understand how different short-term monitoring designs impact the resulting exposure surfaces. METHODS: We used Monte Carlo resampling to simulate three archetypal short-term monitoring sampling designs using oxides of nitrogen (NOx) monitoring data from 69 regulatory sites in California: a year-around Balanced Design that sampled during all seasons of the year, days of the week, and all or various hours of the day; a temporally reduced Rush Hours Design; and a temporally reduced Business Hours Design. We evaluated the performance of each design's land use regression prediction model. RESULTS: The Balanced Design consistently yielded the most accurate annual averages; while the reduced Rush Hours and Business Hours Designs generally produced more biased results. SIGNIFICANCE: A temporally-balanced sampling design is crucial for short-term campaigns such as mobile monitoring aiming to assess long-term exposure in epidemiologic cohorts. IMPACT STATEMENT: Short-term monitoring campaigns to assess long-term air pollution trends are increasingly common, though they rarely conduct temporally balanced sampling. We show that this approach produces biased annual average exposure estimates that can be improved by collecting temporally-balanced samples.

Within-City Variation in Ambient Carbon Monoxide Concentrations: Leveraging Low-Cost Monitors in a Spatiotemporal Modeling Framework.

BACKGROUND: Based on human and animal experimental studies, exposure to ambient carbon monoxide (CO) may be associated with cardiovascular disease outcomes, but epidemiological evidence of this link is limited. The number and distribution of ground-level regulatory agency monitors are insufficient to characterize fine-scale variations in CO concentrations. OBJECTIVES: To develop a daily, high-resolution ambient CO exposure prediction model at the city scale. METHODS: We developed a CO prediction model in Baltimore, Maryland, based on a spatiotemporal statistical algorithm with regulatory agency monitoring data and measurements from calibrated low-cost gas monitors. We also evaluated the contribution of three novel parameters to model performance: high-resolution meteorological data, satellite remote sensing data, and copollutant (PM2.5, NO2, and NOx) concentrations. RESULTS: The CO model had spatial cross-validation (CV) R2 and root-mean-square error (RMSE) of 0.70 and 0.02 parts per million (ppm), respectively; the model had temporal CV R2 and RMSE of 0.61 and 0.04 ppm, respectively. The predictions revealed spatially resolved CO hot spots associated with population, traffic, and other nonroad emission sources (e.g., railroads and airport), as well as sharp concentration decreases within short distances from primary roads. DISCUSSION: The three novel parameters did not substantially improve model performance, suggesting that, on its own, our spatiotemporal modeling framework based on geographic features was reliable and robust. As low-cost air monitors become increasingly available, this approach to CO concentration modeling can be generalized to resource-restricted environments to facilitate comprehensive epidemiological research. https://doi.org/10.1289/EHP10889.

Publicly available low-cost sensor measurements for PM2.5 exposure modeling: Guidance for monitor deployment and data selection.

High-resolution, high-quality exposure modeling is critical for assessing the health effects of ambient PM2.5 in epidemiological studies. Using sparse regulatory PM2.5 measurements as principal model inputs may result in two issues in exposure prediction: (1) they may affect the models' accuracy in predicting PM2.5 spatial distribution; (2) the internal validation based on these measurements may not reliably reflect the model performance at locations of interest (e.g., a cohort's residential locations). In this study, we used the PM2.5 measurements from a publicly available commercial low-cost PM2.5 network, PurpleAir, with an external validation dataset at the residential locations of a representative sample of participants from the Adult Changes in Thought - Air Pollution (ACT-AP) study, to improve the accuracy of exposure prediction at the cohort participant locations. We also proposed a metric based on principal component analysis (PCA) - the PCA distance - to assess the similarity between monitor and cohort locations to guide monitor deployment and data selection. The analysis was based on a spatiotemporal modeling framework with 51 "gold-standard" monitors and 58 PurpleAir monitors for model development, as well as 105 home monitors at the cohort locations for model validation, in the Puget Sound region of Washington State from June 2017 to March 2019. After including calibrated PurpleAir measurements as part of the dependent variable, the external spatiotemporal validation R2 and root-mean-square error, RMSE, for two-week concentration averages improved from 0.84 and 2.22 µg/m3 to 0.92 and 1.63 µg/m3, respectively. The external spatial validation R2 and RMSE for long-term averages over the modeling period improved from 0.72 and 1.01 µg/m3 to 0.79 and 0.88 µg/m3, respectively. The exposure predictions incorporating PurpleAir measurements demonstrated sharper urban-suburban concentration gradients. The PurpleAir monitors with shorter PCA distances improved the model's prediction accuracy more substantially than the monitors with longer PCA distances, supporting the use of this similarity metric.

Assessing the value of complex refractive index and particle density for calibration of low-cost particle matter sensor for size-resolved particle count and PM2.5 measurements.

Low-cost optical scattering particulate matter (PM) sensors report total or size-specific particle counts and mass concentrations. The PM concentration and size are estimated by the original equipment manufacturer (OEM) proprietary algorithms, which have inherent limitations since particle scattering depends on particles' properties such as size, shape, and complex index of refraction (CRI) as well as environmental parameters such as temperature and relative humidity (RH). As low-cost PM sensors are not able to resolve individual particles, there is a need to characterize and calibrate sensors' performance under a controlled environment. Here, we present improved calibration algorithms for Plantower PMS A003 sensor for mass indices and size-resolved number concentration. An aerosol chamber experimental protocol was used to evaluate sensor-to-sensor data reproducibility. The calibration was performed using four polydisperse test aerosols. The particle size distribution OEM calibration for PMS A003 sensor did not agree with the reference single particle sizer measurements. For the number concentration calibration, the linear model without adjusting for the aerosol properties and environmental conditions yields an absolute error (NMAE) of ~ 4.0% compared to the reference instrument. The calibration models adjusted for particle CRI and density account for non-linearity in the OEM's mass concentrations estimates with NMAE within 5.0%. The calibration algorithms developed in this study can be used in indoor air quality monitoring, occupational/industrial exposure assessments, or near-source monitoring scenarios where field calibration might be challenging.

Quantifying the Distribution of Environmental Health Threats and Hazards in Washington State Using a Cumulative Environmental Inequality Index.

Background: Environmental racism, community stressors, and age-related susceptibility play a significant role in environmental inequality. The goal of this article was to use an inequality index (II) to assess the level of equality in environmental threats and hazards based on race, poverty, and age in Washington State. Methods: Using the Washington Environmental Health Disparities Map, we quantified the level of disproportionate burdens on communities with greater populations of people of color, people in poverty, children younger than 5, and people older than 65 using 3 cumulative environmental indices and 10 individual environmental indicators. Results: Census tracts with a higher proportion of people of color and those with people living below 185% federal poverty levels were found to be disproportionately burdened by environmental threats (II = -0.175 and II = -0.167, respectively, p < 0.001). Individual environmental indicators were found to disproportionately burden communities of color and low-income communities. Children younger than 5 were also disproportionately burdened by cumulative environmental indices (II = -0.076, p < 0.001) and individual indicators. Our analysis did not show disproportionate burden of environmental health threats based on the proportion of people older than 65 (II = 0.124, p < 0.001). Discussion: The disproportionate burden of the cumulative environmental threats on communities of color and low-income communities in this study corroborates similar analyses. These findings can be applied in policy and regulatory actions to correct the distributive environmental disparities. Conclusion: We found much higher burdens among historically marginalized communities and children who are more susceptible to environmental threats and hazards.

Deployment, Calibration, and Cross-Validation of Low-Cost Electrochemical Sensors for Carbon Monoxide, Nitrogen Oxides, and Ozone for an Epidemiological Study.

We designed and built a network of monitors for ambient air pollution equipped with low-cost gas sensors to be used to supplement regulatory agency monitoring for exposure assessment within a large epidemiological study. This paper describes the development of a series of hourly and daily field calibration models for Alphasense sensors for carbon monoxide (CO; CO-B4), nitric oxide (NO; NO-B4), nitrogen dioxide (NO2; NO2-B43F), and oxidizing gases (OX-B431)-which refers to ozone (O3) and NO2. The monitor network was deployed in the Puget Sound region of Washington, USA, from May 2017 to March 2019. Monitors were rotated throughout the region, including at two Puget Sound Clean Air Agency monitoring sites for calibration purposes, and over 100 residences, including the homes of epidemiological study participants, with the goal of improving long-term pollutant exposure predictions at participant locations. Calibration models improved when accounting for individual sensor performance, ambient temperature and humidity, and concentrations of co-pollutants as measured by other low-cost sensors in the monitors. Predictions from the final daily models for CO and NO performed the best considering agreement with regulatory monitors in cross-validated root-mean-square error (RMSE) and R2 measures (CO: RMSE = 18 ppb, R2 = 0.97; NO: RMSE = 2 ppb, R2 = 0.97). Performance measures for NO2 and O3 were somewhat lower (NO2: RMSE = 3 ppb, R2 = 0.79; O3: RMSE = 4 ppb, R2 = 0.81). These high levels of calibration performance add confidence that low-cost sensor measurements collected at the homes of epidemiological study participants can be integrated into spatiotemporal models of pollutant concentrations, improving exposure assessment for epidemiological inference.

Health Impact Assessment of the 2020 Washington State Wildfire Smoke Episode: Excess Health Burden Attributable to Increased PM2.5 Exposures and Potential Exposure Reductions.

Major wildfires starting in the summer of 2020 along the west coast of the United States made PM2.5 concentrations in this region rank among the highest in the world. Washington was impacted both by active wildfires in the state and aged wood smoke transported from fires in Oregon and California. This study aims to estimate the magnitude and disproportionate spatial impacts of increased PM2.5 concentrations attributable to these wildfires on population health. Daily PM2.5 concentrations for each county before and during the 2020 Washington wildfire episode (September 7-19) were obtained from regulatory air monitors. Utilizing previously established concentration-response function (CRF) of PM2.5 (CRF of total PM2.5) and odds ratio (OR) of wildfire smoke days (OR of wildfire smoke days) for mortality, we estimated excess mortality attributable to the increased PM2.5 concentrations in Washington. On average, daily PM2.5 concentrations increased 97.1 µg/m3 during the wildfire smoke episode. With CRF of total PM2.5, the 13-day exposure to wildfire smoke was estimated to lead to 92.2 (95% CI: 0.0, 178.7) more all-cause mortality cases; with OR of wildfire smoke days, 38.4 (95% CI: 0.0, 93.3) increased all-cause mortality cases and 15.1 (95% CI: 0.0, 27.9) increased respiratory mortality cases were attributable to the wildfire smoke episode. The potential impact of avoiding elevated PM2.5 exposures during wildfire events significantly reduced the mortality burden. Because wildfire smoke episodes are likely to impact the Pacific Northwest in future years, continued preparedness and mitigations to reduce exposures to wildfire smoke are necessary to avoid excess health burden.

Impacts of implementing Healthy Building guidelines for daily PM2.5 limit on premature deaths and economic losses in urban China: A population-based modeling study.

Given a large fraction of people's exposure to urban PM2.5 occur indoors, reducing indoor PM2.5 levels may offer a more feasible and immediate way to save substantial lives and economic losses attributable to PM2.5 exposure. We aimed to estimate the premature mortality and economic loss reductions associated with achieving the newly established Chinese indoor air guideline and a few hypothetical indoor PM2.5 guideline values. We used outdoor PM2.5 concentrations from 1497 monitoring sites in 339 Chinese cities in 2015, coupled with a steady-state mass balance model, to estimate indoor concentrations of outdoor-infiltrated PM2.5. Using province-specific time-activity patterns for urban residents, we estimated outdoor and indoor exposures to PM2.5 of outdoor origin. We then proceeded to use localized census-based concentration-response models and the value of statistical life estimates to calculate premature deaths and economic losses attributable to PM2.5 exposure across urban China. Finally, we estimated potentially avoidable mortality and corresponding economic losses by meeting the current 24-hour based guideline and various hypothetical indoor limits for PM2.5. In 2015 in urban areas of mainland China, the city-specific annual mean outdoor and indoor PM2.5 concentrations ranged 9-108 µg/m3 and 5-56 µg/m3, respectively. Indoor exposures contributed 62%-91% daily and 68%-83% annually to the total time-weighted exposures. The potential reductions in total deaths and economic losses for the scenario in which daily indoor concentrations met the current guideline of 75 µg/m3, 37.5 µg/m3, and 25 µg/m3 were 16.9 (95% CI: 0.7-62.1) thousand, 87.7 (95% CI: 9.7-197.7) thousand, and 165.5 (95% CI: 30.8-304.0) thousand, respectively. The corresponding reductions in economic losses were 5.7 (95% CI: 0.2-34.8) billion, 29.4 (95% CI: 2.4-109.6) billion, and 55.2 (95% CI: 7.7-168.0) billion US Dollars, respectively. Deaths and economic losses would be reduced exponentially within the range of 0-75 µg/m3 for hypothetical indoor PM2.5 limits. The findings demonstrate the effectiveness of reducing indoor concentrations of outdoor-originated PM2.5 in saving substantial lives and economic losses in China. The analysis provides quantitative evidence to support the implementation of an indoor air quality guideline or standard for PM2.5.

Community-Level Factors Associated with COVID-19 Cases and Testing Equity in King County, Washington.

Individual-level Coronavirus Disease 2019 (COVID-19) case data suggest that certain populations may be more impacted by the pandemic. However, few studies have considered the communities from which positive cases are prevalent, and the variations in testing rates between communities. In this study, we assessed community factors that were associated with COVID-19 testing and test positivity at the census tract level for the Seattle, King County, Washington region at the summer peak of infection in July 2020. Multivariate Poisson regression was used to estimate confirmed case counts, adjusted for testing numbers, which were associated with socioeconomic status (SES) indicators such as poverty, educational attainment, transportation cost, as well as with communities with high proportions of people of color. Multivariate models were also used to examine factors associated with testing rates, and found disparities in testing for communities of color and communities with transportation cost barriers. These results demonstrate the ability to identify tract-level indicators of COVID-19 risk and specific communities that are most vulnerable to COVID-19 infection, as well as highlight the ongoing need to ensure access to disease control resources, including information and education, testing, and future vaccination programs in low-SES and highly diverse communities.

Use of low-cost PM monitors and a multi-wavelength aethalometer to characterize PM2.5 in the Yakama Nation Reservation.

Rural lower Yakima Valley, Washington is home to the reservation of the Confederated Tribes and Bands of the Yakama Nation, and is a major agricultural region. Episodic poor air quality impacts this area, reflecting sources of particulate matter with a diameter of less than 2.5 micrometers (PM2.5) that include residential wood smoke, agricultural biomass burning and other emissions, truck traffic, backyard burning, and wildfire smoke. University of Washington partnered with the Yakama Nation Environmental Management Program to investigate characteristics of PM2.5 using 9 months of data from a combination of low-cost optical particle counters and a 5-wavelength aethalometer (MA200 Aethlabs) over 4 seasons and an episode of summer wildfire smoke. The greatest percentage of hours sampled with PM2.5 >12 µg/m3 occurred during the wildfire smoke episode (59%), followed by fall (23%) and then winter (21%). Mean (SD) values of Delta-C (µg/m3), which has been posited as an indicator of wood smoke, and determined as the mass absorbance difference at 375-880nm, were: summer - wildfire smoke 0.34 (0.52), winter 0.27 (0.32), fall 0.10 (0.22), spring 0.05 (0.11), and summer - no wildfire smoke 0.04 (0.14). Mean (95% confidence interval) values of the absorption Ångström exponent, an indicator of the wavelength dependence of the aerosol, were: winter 1.5 (1.2-1.8), summer - wildfire smoke 1.4 (1.0-1.8), fall 1.3 (1.1-1.4), spring 1.2 (1.1-1.4), and summer - no wildfire smoke 1.2 (1.0-1.3). The trends in Delta-C and absorption Ångström exponents are consistent with expectations that a higher value reflects more biomass burning. These results suggest that biomass burning is an important contributor to PM2.5 in the wintertime, and emissions associated with diesel and soot are important contributors in the fall; however, the variety of emissions sources and combustion conditions present in this region may limit the utility of traditional interpretations of aethalometer data. Further understanding of how to interpret aethalometer data in regions with complex emissions would contribute to much-needed research in communities impacted by air pollution from agricultural as well as residential sources of combustion.

Health Impact Assessment of PM2.5 attributable mortality from the September 2020 Washington State Wildfire Smoke Episode.

Major wildfires that started in the summer of 2020 along the west coast of the U.S. have made PM2.5 concentrations in cities in this region rank among the highest in the world. Regions of Washington were impacted by active wildfires in the state, and by aged wood smoke transported from fires in Oregon and California. This study aims to assess the population health impact of increased PM2.5 concentrations attributable to the wildfire. Average daily PM2.5 concentrations for each county before and during the 2020 Washington wildfire episode were obtained from the Washington Department of Ecology. Utilizing previously established associations of short-term mortality for PM2.5, we estimated excess mortality for Washington attributable to the increased PM2.5 levels. On average, PM2.5 concentrations increased 91.7 µg/m3 during the wildfire episode. Each week of wildfire smoke exposures was estimated to result in 87.6 (95% CI: 70.9, 103.1) cases of increased all-cause mortality, 19.1 (95% CI: 10.0, 28.2) increased cardiovascular disease deaths, and 9.4 (95% CI: 5.1, 13.5) increased respiratory disease deaths. Because wildfire smoke episodes are likely to continue impacting the Pacific Northwest in future years, continued preparedness and mitigations to reduce exposures to wildfire smoke are necessary to avoid this excess health burden.

Developing a Low-Cost Passive Method for Long-Term Average Levels of Light-Absorbing Carbon Air Pollution in Polluted Indoor Environments.

We propose a low-cost passive method for monitoring long-term average levels of light-absorbing carbon air pollution in polluted indoor environments. Building on prior work, the method here estimates the change in reflectance of a passively exposed surface through analysis of digital images. To determine reproducibility and limits of detection, we tested low-cost passive samplers with exposure to kerosene smoke in the laboratory and to environmental pollution in 20 indoor locations. Preliminary results suggest robust reproducibility (r = 0.99) and limits of detection appropriate for longer-term (~1-3 months) monitoring in households that use solid fuels. The results here suggest high precision; further testing involving "gold standard" measurements is needed to investigate accuracy.

Performance of a Low-Cost Sensor Community Air Monitoring Network in Imperial County, CA.

Air monitoring networks developed by communities have potential to reduce exposures and affect environmental health policy, yet there have been few performance evaluations of networks of these sensors in the field. We developed a network of over 40 air sensors in Imperial County, CA, which is delivering real-time data to local communities on levels of particulate matter. We report here on the performance of the Network to date by comparing the low-cost sensor readings to regulatory monitors for 4 years of operation (2015-2018) on a network-wide basis. Annual mean levels of PM10 did not differ statistically from regulatory annual means, but did for PM2.5 for two out of the 4 years. R2s from ordinary least square regression results ranged from 0.16 to 0.67 for PM10, and increased each year of operation. Sensor variability was higher among the Network monitors than the regulatory monitors. The Network identified a larger number of pollution episodes and identified under-reporting by the regulatory monitors. The participatory approach of the project resulted in increased engagement from local and state agencies and increased local knowledge about air quality, data interpretation, and health impacts. Community air monitoring networks have the potential to provide real-time reliable data to local populations.

Calibration of low-cost particulate matter sensors: Model development for a multi-city epidemiological study.

Low-cost air monitoring sensors are an appealing tool for assessing pollutants in environmental studies. Portable low-cost sensors hold promise to expand temporal and spatial coverage of air quality information. However, researchers have reported challenges in these sensors' operational quality. We evaluated the performance characteristics of two widely used sensors, the Plantower PMS A003 and Shinyei PPD42NS, for measuring fine particulate matter compared to reference methods, and developed regional calibration models for the Los Angeles, Chicago, New York, Baltimore, Minneapolis-St. Paul, Winston-Salem and Seattle metropolitan areas. Duplicate Plantower PMS A003 sensors demonstrated a high level of precision (averaged Pearson's r = 0.99), and compared with regulatory instruments, showed good accuracy (cross-validated R2 = 0.96, RMSE = 1.15 µg/m3 for daily averaged PM2.5 estimates in the Seattle region). Shinyei PPD42NS sensor results had lower precision (Pearson's r = 0.84) and accuracy (cross-validated R2 = 0.40, RMSE = 4.49 µg/m3). Region-specific Plantower PMS A003 models, calibrated with regulatory instruments and adjusted for temperature and relative humidity, demonstrated acceptable performance metrics for daily average measurements in the other six regions (R2 = 0.74-0.95, RMSE = 2.46-0.84 µg/m3). Applying the Seattle model to the other regions resulted in decreased performance (R2 = 0.67-0.84, RMSE = 3.41-1.67 µg/m3), likely due to differences in meteorological conditions and particle sources. We describean approach to metropolitan region-specific calibration models for low-cost sensors that can be used with cautionfor exposure measurement in epidemiological studies.

Contribution of low-cost sensor measurements to the prediction of PM2.5 levels: A case study in Imperial County, California, USA.

Regulatory monitoring networks are often too sparse to support community-scale PM2.5 exposure assessment while emerging low-cost sensors have the potential to fill in the gaps. To date, limited studies, if any, have been conducted to utilize low-cost sensor measurements to improve PM2.5 prediction with high spatiotemporal resolutions based on statistical models. Imperial County in California is an exemplary region with sparse Air Quality System (AQS) monitors and a community-operated low-cost network entitled Identifying Violations Affecting Neighborhoods (IVAN). This study aims to evaluate the contribution of IVAN measurements to the quality of PM2.5 prediction. We adopted the Random Forest algorithm to estimate daily PM2.5 concentrations at a 1-km spatial resolution using three different PM2.5 datasets (AQS-only, IVAN-only, and AQS/IVAN combined). The results show that the integration of low-cost sensor measurements is an effective way to significantly improve the quality of PM2.5 prediction with an increase of cross-validation (CV) R2 by ~0.2. The IVAN measurements also contributed to the increased importance of emission source-related covariates and more reasonable spatial patterns of PM2.5. The remaining uncertainty in the calibrated IVAN measurements could still cause apparent outliers in the prediction model, highlighting the need for more effective calibration or integration methods to relieve its negative impact.

The Washington State Environmental Health Disparities Map: Development of a Community-Responsive Cumulative Impacts Assessment Tool.

Communities across Washington State have expressed the need for neighborhood-level information on the cumulative impact of environmental hazards and social conditions to illuminate disparities and address environmental justice issues. Many existing mapping tools have not explicitly integrated community voice and lived experience as an integral part of their development. The goals of this project were to create a new community-academic-government partnership to collect and summarize community concerns and to develop a publicly available mapping tool that ranks relative environmental health disparities for populations across Washington State. Using a community-driven framework, we developed the Washington Environmental Health Disparities Map, a cumulative environmental health impacts assessment tool. Nineteen regularly updated environmental and population indicators were integrated into the geospatial tool that allows for comparisons of the cumulative impacts between census tracts. This interactive map provides critical information for the public, agencies, policymakers, and community-based organizations to make informed decisions. The unique community-academic-government partnership and the community-driven framework can be used as a template for other environmental and social justice mapping endeavors.