Characteristics of bioaerosol emissions from a municipal wastewater treatment plant: Health risk assessment and microbial composition.

Bioaerosols released from municipal wastewater treatment plants (MWWTPs) contain pathogenic microorganisms, if dispersed into the atmosphere, which pose potential health risks to humans. In this study, the concentrations and size distribution of bioaerosol, factors on the bioaerosol emission, exposure risk, and microbial composition in different treatment units of a MWWTP were investigated. The results showed that bioaerosol was released to different degrees in each treatment unit, with the concentrations of bioaerosol varied widely, ranging from 978 to 3710 CFU/m3. FG and PST were primary bioaerosol emission sources in MWWTP. COD concentration, wind speed (WS) and relative humidity (RH) significantly influenced bioaerosol concentrations. The proportion of inhalable particles (< 4.7 µm) ranged from 51.35 % to 83.33 %, and bioaerosol emitted from WWTP caused a non-carcinogenic risk to children by the exposure risk assessment (HI > 1), which need to be paid more attention. Bacterial, fungal and actinomycete aerosols were detected in each treatment unit of MWWTP. Among these bioaerosols, bacterial aerosol was dominant. Importantly, several pathogenic bacteria including Sphingobium, Brevundimonas, Romboutsia, Arcobacter, Acinetobacter, and Mycobacterium were identified within the airborne bacteria population, most of which originated from wastewater or sludge, particularly in the ambient air of AeT. Pathogenic bacteria from MWWTP should be studied further to determine their long-term behavior and possible health risks.

Green Synthesis of CoZn-Based Metal-Organic Framework (CoZn-MOF) from Waste Polyethylene Terephthalate Plastic As a High-Performance Anode for Lithium-Ion Battery Applications.

The recycling of discarded polyethylene terephthalate (PET) plastics produced metal-organic frameworks can effectively minimize environmental pollution and promote sustainable economic development. In this study, we developed a method using NaOH in alcohol and ether solvent environments to degrade PET plastics for synthesizing terephthalic acid. The method achieved a 97.5% degradation rate of PET plastics under a reaction temperature of 80 °C for 60 min. We used terephthalic acid as a ligand from the degradation products to successfully synthesize two types of monometallic and bimetallic CoZn-MOF materials. We investigated the impact of different metal centers and solvents on the electrochemical performance of the MOF materials. The result showed that the MOF-DMF/H2O material maintained a specific capacity of 1485.5 mAh g-1 after 100 cycles at a current density of 500 mA g-1, demonstrating excellent rate capability and cycling stability. In addition, our finding showed that the performance difference might be attributed to the synergistic effect of bimetallic Co2+ and Zn2+ in MOF-DMF/H2O, rapid lithium-ion diffusion and electron transfer rates, and the absence of coordinating solvents. Additionally, the non-in situ X-ray powder diffraction, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy analysis results showed that lithium storage in the MOF-DMF/H2O electrode mainly depended on the aromatic C6 ring and carboxylate portions of the organic ligands in different charge and discharge states. Lithium ions can be reversibly inserted/removed into/from the electrode material. The physical adsorption on the MOF surface through electrostatic interactions enhanced both capacity and cycling stability. This research provides valuable insight for mitigating solid waste pollution, promoting sustainable economic development, and advancing the extensive applications of MOF materials in lithium-ion batteries.

Waste PET Plastic-Derived CoNi-Based Metal-Organic Framework as an Anode for Lithium-Ion Batteries.

Recycling waste PET plastics into metal-organic frameworks is conducive to both pollution alleviation and sustainable economic development. Herein, we have utilized waste PET plastic to synthesize CoNi-MOF applied to lithium battery anode materials via a low-temperature solvothermal method for the first time. The preparation process is effortless, and the sources' conversion rate can reach almost 100%. In addition, the anode performance of MOFs with various Co/Ni mole ratios was investigated. The as-synthesized Co0.8Ni-MOF exhibits excellent crystallinity, purity, and electrochemical performance. The initial discharge and charge capacities are 2496 and 1729 mAh g-1, respectively. Even after 200 cycles, the Co0.8Ni-MOF electrode can exhibit a high Coulombic efficiency of over 99%. Consequently, given the environmental and economic benefits, the Co0.8Ni-MOF derived from waste PET plastic is thought to be an appealing anode material for lithium-ion batteries.

Dynamic Evaluation of an Active Axial Magnetic Levitated Bearing System in a Hemocompatibility Assessment Platform.

To evaluate the hemocompatibility of individual components of our pediatric left ventricular assist device (LVAD), we proposed a hemocompatibility assessment platform (HAP) with a magnetic levitated bearing system. The HAP consists of a drive system utilizing a brushless direct current (BLDC) motor, passive magnetic bearings (PMB), and an active magnetically levitated bearing (AMB) to reduce the hemolysis generated by HAP itself. In this study, we designed and evaluated the performance of the AMB by measuring radial and axial displacements of the rotor resulting from radially destabilizing forces as well as the performance of the drive system when rotated at increasing speeds to 1,200 rotations per minute (rpm). The results show that, with radial disturbance, the AMB is capable of maintaining axial stability for the BLDC motor system. The AMB can control up to 1,200 rpm without any contact between the rotor and stator. Future work includes geometry optimization for the AMB structure and increase the capability to control stable high-speed rotation for the entire system. Clinical Relevance- This work furthers the development of the magnetic levitated bearing system for a hemocompatibility assessment platform that will be used to enhance and accelerate the development of adult and pediatric LVADs.

Numerical and Experimental Analysis for a Magnetic Levitation System in a Hemocompatibility Assessment Platform.

Development of pediatric left ventricular assist devices (LVADs) has lagged behind that of adult LVADs, primarily due to the size and hemocompatibility constraints of pediatric anatomy. To quantify sources of blood trauma during LVAD development, we proposed a hemocompatibility assessment platform (HAP) that can evaluate the hemocompatibility of individual components of LVADs. To eliminate the hemolysis induced by the HAP itself, we incorporated passive magnetic (PM) bearings to suspend the rotor radially and an active magnetic bearing (AMB) to control the axial position. In this study, we numerically evaluated AMB forces of 2 geometries and validated the model by comparing its predictions with experimental results. The magnetic forces generated by the AMB were evaluated by increasing the rotor-stator gap from 0.1 mm to 0.5 mm with a 0.1 mm increment and by varying the coil current from -2 A to 2 A with a 1 A increment. The average error of the numerical models was 8.8% and 7.0% for the two geometries, respectively. Higher errors were found at smaller (<0.2mm) rotor-stator gaps. For both biasing ring sizes, the AMB exhibits high magnetic stiffness from -1 A to 1 A, though it saturates for currents of -2 A and 2 A. This region of high current stiffness was identified as the optimal control region. In future work, this function will be used to tune a control algorithm to modulate current supplied to the AMB, ultimately stabilizing the rotor axially. Clinical Relevance- This work furthers the development of a hemocompatibility assessment platform that will enhance and accelerate the development of adult and pediatric LVADs.

Concentration and risk assessment of PCNs in green tea in different locations in China.

Polychlorinated naphthalenes (PCNs) were added to the Stockholm Convention list of persistent organic pollutants in 2015. PCNs are mainly unintentionally produced during industrial processes nowadays, and can be widely found in environmental media and foodstuffs. Dietary intake is the primary pathway for human exposure to PCNs. PCNs in different categories of foodstuffs have been reported. However, little information on PCN concentrations in green tea, a popular beverage worldwide is available. In this study, all 75 PCN congener concentrations and distributions in green tea samples (n = 102) from 11 regions in China were determined, and risk assessment of human exposure to PCNs through tea consumption was conducted. The PCN concentrations in all the green tea samples were 3.62-175 pg/g dry weight (mean 36.1 pg/g dry weight). Similar PCN homolog and congener profiles were found in green tea samples from different areas. The dominant PCN homologs in all of the green tea samples were di-CNs, tetra-CNs, and tri-CNs. No direct relationships were found between PCN emission sources and PCN concentrations in the green tea samples. The brewing technique could affect the PCN concentrations and homolog profiles in tea leaves. PCNs in green tea from China were found to pose little risk to humans.

Short- and medium-chain chlorinated paraffins in honey from China: Distribution, source analysis, and risk assessment.

Chlorinated paraffins (CPs) are industrial chemicals produced in large quantities. Short-chain CPs (SCCPs) were classified as persistent organic pollutants under the Stockholm Convention in 2017. Medium-chain CPs (MCCPs) became candidate persistent organic pollutants in 2021. CPs are now ubiquitously found in the environment. Honey bees can be exposed to CPs during foraging, and this exposure subsequently results in the contamination of honey and other bee products along with colony food production and storage. Here, SCCP and MCCP concentrations in honey collected from Chinese apiaries in 2015 and 2021 were determined. Total CP concentrations in honey from 2021 to 2015 were comparable, but the ratio of MCCPs/SCCPs was higher in 2021 than in 2015. SCCP and MCCP congener group profiles in all honey samples were similar and dominated by C10-11Cl6-7 and C14Cl6-7, respectively. MCCP concentrations were also higher than SCCP concentrations in bees, pollen, and wax but not in bee bread, which were all collected in 2021. The order of average CP concentrations was determined as wax > bee > pollen > bee bread > honey. Poor relationships were found between SCCP concentrations in honey and other samples, but a relationship between MCCP concentrations in honey and other samples was observed. Migration tests of CPs in plastic bottles showed essentially no migration into honey during storage. The risks to humans from CPs in honey are low.

Occurrence of per- and polyfluoroalkyl substances (PFASs) in raw milk and feed from nine Chinese provinces and human exposure risk assessment.

The per- and polyfluoroalkyl substances (PFASs) are substantially produced and applied in industrial and domestic products, which have recently aroused great public concern for their potential toxicity to humans. In the present study, raw milk (n = 107) and cow feed samples (n = 70) were collected across nine Chinese provinces, in order to investigate the occurrence of PFASs in milk and feed, and the human exposure risk to milk. The concentrations of PFASs are in the range of < method detection limit -9.82 ng/g dw (average: 1.03 ng/g dw) for milk and 0.99-144 ng/g dw (7.68 ng/g dw) for feed. Perfluorobutanoic acid (34.0%) dominates in feed, while perfluorooctanesulfonic acid (67.5%) dominates in milk. No significant positive correlations of PFASs are observed between paired feed and milk (p > 0.05). However, feeds collected around fluorination production area show relatively higher PFAS levels than those from other areas, which also increase PFAS levels in milk. Risk assessment of PFASs through milk consumption is carried out according to evolving reference doses (RfDs). The hazard quotient is more than one for both adults and children when the strictest RfDs are applied. The Monte Carlo Simulation shows that children face higher PFAS exposure risk than adults.

Hemocompatibility Assessment Platform Drive System Design: Trade-off between Motor Performance and Hemolysis.

Left ventricular assist devices (LVADs) have long been used to treat adults with heart failure, but LVAD options for pediatric patients with heart failure are lacking. Despite the urgent need for long-term, implantable pediatric LVADs, design challenges such as hemolysis, pump thrombosis, and bleeding persist. We have developed a Hemocompatibility Assessment Platform (HAP) to identify blood trauma from individual LVAD components. A HAP would aid in refining pump components before in vivo testing, thereby preventing unnecessary animal sacrifice and reducing development time and cost. So that the HAP does not confound hemolysis data, the HAP drive system consists of an enlarged air-gap motor coupled to a magnetic levitation system. Although it is known that an enlarged air gap motor will have diminished performance, while the larger gap in the motor will cause less blood damage, the trade-offs are not fully characterized. Therefore, in this study we evaluated these trade-offs to determine an optimal rotor diameter for the HAP drive motor. The motor performance was characterized with an experimental method by determining the torque constant for the HAP drive motor with varied rotor diameters. The torque threshold was set as 10 mNm to achieve a nominal current of 3.5A. Hemolysis in the HAP drive motor gap was estimated by calculating scalar shear stress generated in the HAP motor gap analytically and numerically. A design criterion of 30 Pa was selected for scalar shear stress to achieve minimal hemolysis and platelet activation in the HAP drive system.Clinical Relevance- We evaluated a Hemocompatibility Assessment Platform for developing LVAD prototypes that can best balance motor performance and hemocompatibility. This design method can assist with optimizing the drive system during the research stage and illustrates how motor geometry can be tuned to reduce blood trauma.

Beyond Justice Perceptions: The Role of Interpersonal Justice Trajectories and Social Class in Perceived Legitimacy of Authority Figures.

There is considerable evidence that the experience of justice is associated with perceived legitimacy of authority, but there has been no research about this association when considering past rather than current fairness. Based on the fairness heuristic theory, we tested the hypothesis that interpersonal justice trajectories positively affect perceived legitimacy of the authority; we also tested whether social class moderated this effect. Community residents (N = 111; 54 women) rated the authority's fairness on 16 consecutive weeks and rated perceived legitimacy on the 16th week. The results of latent growth modeling showed that the trajectory of interpersonal justice scores leading up to the final week significantly predicted perceived legitimacy, regardless of the current experience of interpersonal fairness. Tests of moderation showed that the legitimacy perceptions of individuals of lower subjective social class were significantly affected by interpersonal justice trajectories, whereas this was not the case among individuals of higher subjective social class. The results are discussed in terms of their implications for research on perceived legitimacy and justice, as well as their implications for understanding social class.

Ultrasonic Characteristics and Severity Assessment of Lung Ultrasound in COVID-19 Pneumonia in Wuhan, China: A Retrospective, Observational Study.

The clinical application of lung ultrasound (LUS) in the assessment of coronavirus disease 2019 (COVID-19) pneumonia severity remains limited. Herein, we investigated the role of LUS imaging in COVID-19 pneumonia patients and the relationship between LUS findings and disease severity. This was a retrospective, observational study at Tongji Hospital in Wuhan, on 48 recruited patients with COVID-19 pneumonia, including 32 non-critically ill patients and 16 critically ill patients. LUS was performed and the respiratory rate oxygenation (ROX) index, disease severity, and confusion, blood urea nitrogen, respiratory rate, blood pressure, and age (CURB-65) score were recorded on days 0-7, 8-14, and 15-21 after symptom onset. Lung images were divided into 12 regions, and the LUS score (0-36 points) was calculated. Chest computed tomography (CT) scores (0-20 points) were also recorded on days 0-7. Correlations between the LUS score, ROX index, and CURB-65 scores were examined. LUS detected COVID-19 pneumonia in 38 patients. LUS signs included B lines (34/38, 89.5%), consolidations (6/38, 15.8%), and pleural effusions (2/38, 5.3%). Most cases showed more than one lesion (32/38, 84.2%) and involved both lungs (28/38, 73.7%). Compared with non-critically ill patients, the LUS scores of critically ill patients were higher (12 (10-18) vs 2 (0-5), p < 0.001). The LUS score showed significant negative correlations with the ROX index on days 0-7 (r = -0.85, p < 0.001), days 8-14 (r = -0.71, p < 0.001), and days 15-21 (r = -0.76, p < 0.001) after symptom onset. However, the LUS score was positively correlated with the CT score (r = 0.82, p < 0.001). The number of patients with LUS-detected lesions decreased from 27 cases (81.8%) to 20 cases (46.5%), and the LUS scores significantly decreased from 4 (2-10) to 0 (0-5) (p < 0.001) from days 0-7 to 17-21. We conclude that LUS can detect lung lesions in COVID-19 pneumonia patients in a portable, real-time, and safe manner. Thus, LUS is helpful in assessing COVID-19 pneumonia severity in critically ill patients.

Aroma Compounds in Chicken Broths of Beijing Youji and Commercial Broilers.

The unique flavor of Beijing Youji (BJY) chicken broth compared with that of commercial broilers (CB) was investigated by solvent-assisted flavor evaporation combined with AEDA/GC-O (aroma extract dilution analysis of gas chromatography-olfactometry), quantitation, and aroma recombination. A total of 71 odorants with almost the same major odorants (≥10 ng/g broth) were found by GC-O in both BJY and CB broths. However, BJY broth had thirty-two more extra odorants than CB broth, indicating the rich fragrance of the former. Aroma recombination and omission experiments demonstrated that 21 versus 17 odorants (with OAV ≥ 1) contributed significantly to BJY and CB broth aromas, respectively. Those key odorants mainly included sulfur-containing compounds and aliphatic aldehydes, such as 2-methyl-3-furanthiol, 3-(methylthio)propanal, ( E, E)-2,4-decadienal, etc. Furthermore, composition analysis of the meat suggested that the better flavor, with rather more odorants, of BJY broth is probably due to higher contents of polyunsaturated fatty acids and water-soluble flavor precursor, including ribose, cysteine, thiamine, etc., present in the BJY meat.