Inhibition of hepatitis B virus replication via HBV DNA cleavage by Cas9 from Staphylococcus aureus.

Chronic hepatitis B virus (HBV) infection is difficult to cure due to the presence of covalently closed circular DNA (cccDNA). Accumulating evidence indicates that the CRISPR/Cas9 system effectively disrupts HBV genome, including cccDNA, in vitro and in vivo. However, efficient delivery of CRISPR/Cas9 system to the liver or hepatocytes using an adeno-associated virus (AAV) vector remains challenging due to the large size of Cas9 from Streptococcus pyogenes (Sp). The recently identified Cas9 protein from Staphylococcus aureus (Sa) is smaller than SpCas9 and thus is able to be packaged into the AAV vector. To examine the efficacy of SaCas9 system on HBV genome destruction, we designed 5 guide RNAs (gRNAs) that targeted different HBV genotypes, 3 of which were shown to be effective. The SaCas9 system significantly reduced HBV antigen expression, as well as pgRNA and cccDNA levels, in Huh7, HepG2.2.15 and HepAD38 cells. The dual expression of gRNAs/SaCas9 in these cell lines resulted in more efficient HBV genome cleavage. In the mouse model, hydrodynamic injection of gRNA/SaCas9 plasmids resulted in significantly lower levels of HBV protein expression. We also delivered the SaCas9 system into mice with persistent HBV replication using an AAV vector. Both the AAV vector and the mRNA of Cas9 could be detected in the C3H mouse liver cells. Decreased hepatitis B surface antigen (HBsAg), HBV DNA and pgRNA levels were observed when a higher titer of AAV was injected, although this decrease was not significantly different from the control. In summary, the SaCas9 system accurately and efficiently targeted the HBV genome and inhibited HBV replication both in vitro and in vivo. The system was delivered by an AAV vector and maybe used as a novel therapeutic strategy against chronic HBV infection.

A one-step strategy for ultra-fast and low-cost mass production of plastic membrane microfluidic chips.

An ultra-fast, extremely cost-effective, and environmentally friendly method was developed for fabricating flexible microfluidic chips with plastic membranes. With this method, we could fabricate plastic microfluidic chips rapidly (within 12 seconds per piece) at an extremely low cost (less than $0.02 per piece). We used a heated perfluoropolymer perfluoroalkoxy (often called Teflon PFA) solid stamp to press a pile of two pieces of plastic membranes, low density polyethylene (LDPE) and polyethylene terephthalate (PET) coated with an ethylene-vinyl acetate copolymer (EVA). During the short period of contact with the heated PFA stamp, the pressed area of the membranes permanently bonded, while the LDPE membrane spontaneously rose up at the area not pressed, forming microchannels automatically. These two regions were clearly distinguishable even at the micrometer scale so we were able to fabricate microchannels with widths down to 50 microns. This method combines the two steps in the conventional strategy for microchannel fabrication, generating microchannels and sealing channels, into a single step. The production is a green process without using any solvent or generating any waste. Also, the chips showed good resistance against the absorption of Rhodamine 6G, oligonucleotides, and green fluorescent protein (GFP). We demonstrated some typical microfluidic manipulations with the flexible plastic membrane chips, including droplet formation, on-chip capillary electrophoresis, and peristaltic pumping for quantitative injection of samples and reagents. In addition, we demonstrated convenient on-chip detection of lead ions in water samples by a peristaltic-pumping design, as an example of the application of the plastic membrane chips in a resource-limited environment. Due to the high speed and low cost of the fabrication process, this single-step method will facilitate the mass production of microfluidic chips and commercialization of microfluidic technologies.