Assessment of organochlorine pesticide contamination in relation to soil properties in the Pearl River Delta, China.

High levels of organochlorine pesticides (OCPs) such as hexachlorocyclohexanes (HCHs) and dichlorodiphenyltrichloroethanes (DDTs) have been found in soil of the Pearl River Delta (PRD), attributable to high pesticide application in this area. Consequently, the occurrence and environmental effect of HCHs and DDTs in the PRD have attracted considerable attention. However, study focusing on the influence of potential factors such as soil property on the environmental fate of HCHs and DDTs in the PRD has been rare. The present study aimed to investigate the impact of soil physiochemical properties on the distribution patterns and fate of soil HCHs and DDTs on a large spatial scale. Levels of HCHs (sum of α-, ß-, γ- and δ-HCH) and DDTs (sum of 1,1,1-trichloro-2,2-bis-(p-chlorophenyl)ethane (p,p'-DDT), 1,1-dichloro-2,2-bis-(p-chlorophenyl)ethane (p,p'-DDD), and 1,1-dichloro-2,2-bis-(p-chlorophenyl)ethylene (p,p'-DDE)) in 151 soil samples covering all areas of the PRD and physiochemical parameters related to soil properties including pH, total organic carbon (TOC), total Fe (TFe), DCB-Fe (DFe), amorphous-Fe (AFe), complexed-Fe (CFe), total Mn (TMn), DCB-Mn (DMn), amorphous-Mn (AMn), complexed-Mn (CMn) and cation exchange capacity (CEC) were determined. The residual levels of HCHs and DDTs in soils of the present study, which are mainly controlled by soil TOC and CFe content and varying spatially with land use types, may potentially pose ecological risk to plants and animals. On the other hand, transformation of soil HCHs may be affected by pH and DDT transformation correlated significantly with AFe and CFe. Currently, soil has become an important secondary source of OCPs and the re-emission potential of OCPs in soil was mainly affected by soil OCP concentrations and land use types.

[Development of a low-cost single chamber microbial fuel cell type BOD sensor].

The principle of the detector is based on the effect of microbial toxicity of water sample on the electricity generation in microbial fuel cell (MFC). The performance of the MFC-type biotoxicity detector was evaluated with the synthetic water containing heavy metals of Cd2+ and Cu2+. The experimental results demonstrated that: (1) relative to the conventional methods, the MFC-type detector is easy to operate, and suitable for on-line measurements with high sensitivity; (2) it only requires 4 h to complete measurements, and can get ready for next measurement within 4 h; (3) there is a significant linear correlation between the concentration of toxic metal(s) and inhibition ratios in Coulombic yields of MFC. As the IC20 (concentration causing 20% inhibition) of Cd2+, Cu2+ and mixed metals (Cd2+ and Cu2+) were 0.6, 0.8 and 0.25 mg/L, the regression coefficients were shown to be 0.9960, 0.9744 and 0.9907.

[Development of a low-cost single chamber microbial fuel cell type BOD sensor].

The 5-d biochemical oxygen demand (BOD5) test is the most conventional method to determine the concentration of biodegradable organics in wastewater. However, this method is time-consuming and usually requires experience and skill to produce creditable results, which is also not suitable for on-line measurements. This study described a single-chamber mediator-less microbial fuel cell (MFC)-type BOD sensor as an alternative method to BOD5. In such MFC, MnO2 was used as the cathode catalyst instead of Pt and the expensive proton exchange membrane was replaced with the cation exchange membrane. The factors including the external resistance, pH of anolyte, the reaction time and rinse time on BOD sensor were explored, and the results were compared with the values determined by BOD5. The experimental results showed that the optimal conditions are: the external resistance of 12 k omega, pH of 7.0, and the reaction period of 2 h and the rinse time of 2-10 min. The low detection limit is 0.2 mg/L and the precision is 0.33%. This study indicates that MFC-type sensor can be used as a reliable method to determine BOD in wastewater, supported by the good linear correlation between BOD concentration and coulombs generation (regression coefficient, R2 = 0.9992) and the small relative error of 4% between MFC-type sensor and BOD5. Such device provides a low-cost, easy-operated, fast-response, sensitive and reliable method to measure BOD in wastewater, and also is suitable for on-line measurements.