Spatiotemporal variations and risk assessment of estrogens in the water of the southern Bohai Sea: A comprehensive investigation spanning three years.

The ubiquitous and adverse effects of estrogens have aroused global concerns. Natural and synthetic estrogens in 255 water samples from the southern Bohai Sea were analyzed over three years. Total estrogen concentrations were 11.0-268 ng/L in river water and 1.98-99.7 ng/L in seawater, with bisphenol A (BPA) and 17α-ethynylestradiol (EE2) being the predominant estrogens, respectively. Estrogen showed the highest concentrations in summer 2018, followed by spring 2021 and spring 2019, which was consistent with the higher estrogen flux from rivers during summer. Higher estrogen concentrations in 2021 than in 2019 were driven by the higher level of BPA, an additive used in personal protective equipment. Estrogen exhibited higher concentrations in the southern coast of the Yellow River Delta and the northeastern coast of Laizhou bay due to the riverine input and aquaculture. Estrogens could disturb the normal endocrine activities of organisms and edict high ecological risks (90th simulated RQT > 1.0) to aquatic organisms, especially to fish. EE2 was the main contributor of estrogenic potency and ecological risk, which requires special concern. This is the first comprehensive study of estrogen spatiotemporal variations and risks in the Bohai Sea, providing insights into the environmental behavior of estrogens in coastal regions.

Landscape and risk assessment of microplastic contamination in farmed oysters and seawater along the coastline of China.

Microplastic (MP) pollution poses a significant threat to marine ecosystem and seafood safety. However, comprehensive and comparable assessments of MP profiles and their ecological and health in Chinese farming oysters are lacking. This study utilized laser infrared imaging spectrometer (LDIR) to quantify MPs in oysters and its farming seawater at 18 sites along Chinese coastlines. Results revealed a total of 3492 MPs in farmed oysters and seawater, representing 34 MP types, with 20-100 µm MP fragments being the dominant. Polyurethane (PU) emerged as the predominant MP type in oysters, while polysulfones were more commonly detected in seawater. Notably, oysters from the Bohai Sea exhibited a higher abundance of MPs (13.62 ± 2.02 items/g) and estimated daily microplastic intake (EDI, 2.14 ± 0.26 items/g/kg·bw/day), indicating a greater potential health risk in the area. Meanwhile, seawater from the Yellow Sea displayed a higher level (193.0 ± 110.7 items/L), indicating a greater ecological risk in this region. Given the pervasiveness and abundance of PU and its high correlation with other MP types, we proposed PU as a promising indicator for monitoring and assessing the risk MP pollution in mariculture in China. These findings provide valuable insights into the extent and characteristics of MP pollution in farmed oysters and seawater in China.

An integrated approach based on HFE-D, GIS techniques, GQISWI, and statistical analysis for the assessment of potential seawater intrusion: coastal multilayered aquifer of Ghaemshahr-Juybar (Mazandaran, Iran).

The overexploitation of coastal aquifers is one of the important reasons for the salinity of groundwater due to seawater intrusion (SWI). This study assesses the hydrochemical changes of the Ghaemshahr-Juybar (GH.-J.) plain. For this purpose, specific statistical methods, modified Piper diagram groundwater quality indicators ([Formula: see text] and [Formula: see text]), groundwater quality index specific to seawater intrusion ([Formula: see text]), and hydrochemical facies evolution diagram (HFE-D) along with GIS (Geographic Information System) techniques were applied to identify the spatiotemporal changes of salinity in coastal multilayer alluvial aquifer. The results show that the chemical composition in the GH.-J. aquifer is basically controlled by three main factors: (1) Caspian SWI and fossil saltwater penetration from an underlying layer, (2) reverse cation exchange process, and (3) feeding by domestic sewage, agricultural activities, and use of nitrate chemical fertilizers. The investigation of the hydrogeochemical facies evolution process shows that due to the reduction of extraction from wells, saltwater infiltration has significantly decreased. Therefore, according to the geological and lithological conditions of the aquifer and exposure to seawater, it is possible to prevent the entry of saltwater from the confined aquifer into the unconfined aquifer and the saltwater intrusion by developing well optimal operation policies in order to control withdrawal from semi-deep wells and the elimination of deep wells. This practical approach to managing the salinity of coastal aquifers is suitable for the allocating groundwater resources and for use in the development of aquifer simulation models.

Study on reconstruction and analytical method of seawater radioactive gamma spectrum.

Gamma detector detection technology based on NaI(Tl) scintillation crystal has become a popular research topic and has been applied in the field of marine radioactive environment automatic monitoring because of its advantages of low power consumption, low cost and strong environmental adaptability. However, insufficient energy resolution of the NaI(Tl) detector and great Compton scattering in the low-energy region caused by the abundance of natural radionuclides in seawater hinder the automatic analysis of radionuclides in seawater. This study adopts the combination of theoretical derivation, simulation experiment, water tank test and seawater field test, establishing an effective and feasible spectrum reconstruction method. The measured spectrum in seawater is regarded as the output signal formed by the convolution of the incident spectrum and the detector response function. The acceleration factor p is introduced to construct the Boosted-WNNLS deconvolution algorithm, which is used to iteratively reconstruct the spectrum. The analysis results of the simulation test, water tank test and field test meet the radionuclide analysis speed and accuracy requirements for the in-situ automatic monitoring of seawater radioactivity. The spectrum reconstruction method in this study converts the physical problem of insufficient detection accuracy of spectrometer in the practical application into a mathematical problem of deconvolution solution, restores the original radiation information in seawater, and improves the resolution of the seawater gamma spectrum.

Delineation of seawater intrusion and groundwater quality assessment in coastal aquifers: The Korba coastal aquifer (Northeastern Tunisia).

The aim of this study is to determine the general state of the Korba aquifer (northwestern Tunisia) with respect to seawater intrusion and to assess the suitability of groundwater for drinking and irrigation purposes. A total of 60 groundwater samples were collected and analysed for physicochemical parameters (pH, EC, TDS, Na+, K+, Ca2+, Mg2+, HCO3-, Cl-, NO3-, SO42- and Br-). Major ionic ratios highlighted the dominance of the reverse ion exchange process triggered by the marine intrusion. Br-/Cl- ratio suggested that the irrigation with saline water and wastewater were potential additional sources of salinization. Hydrochemical Facies Evolution Diagram coupled with a GIS-based framework revealed that most of samples are located beneath the mixing line, showing dominant marine intrusion process. Based on the water quality index, most of groundwater samples were unsuitable for drinking. In addition, according to high sodium adsorption ratio, the groundwater quality was limited for irrigation purposes.

Assessment and delineation of potential groundwater recharge zones in areas prone to saltwater intrusion hazard: a case from Central Iran.

Demarcation of the potential zones for groundwater artificial recharge (GAR) based on the most influential factors is an urgent need for retardation of saltwater intrusion and, thus, sustainability of groundwater resources in the arid zones. This study developed an overlay-index methodology to delineate favorable GAR zones by a linear combination of 11 influential thematic layers in ArcGIS. The proposed methodology was implemented on two coastal aquifer settings Sharif-Abad (SAA) and Qom-Kahak (QKA) aquifers adjacent to Salt Lake, Central Iran. Results indicated that 16.41% of the surface of SAA and 28.58% of QKA were identified as the high potential zone for GAR mainly located in low GW vulnerability parts. Based on the analysis of the area under the receptive operating curve (AUC), the produced GAR map has an accuracy of 0.643, and 0.611 for SAA and QKA aquifers, respectively, which relies on the acceptable limit. Finally, the quantity of water required for GAR to control the intrusion of seawater at the suitable parts of these aquifers was estimated as 25 MCM and 35 MCM, annually. The methodology adopted in this study can serve as a holistic assessment for the detection of SWI in coastal aquifers, and also a comprehensive blueprint for managers to delineate the favorable GAR zones, especially in arid regions.

Dissolved metal assessment in surface seawater: A spatial-seasonal evaluation in the Zhejiang coastal waters, the East China Sea.

The spatial-seasonal distributions and variations, correlations with environmental variables and the pollution degrees of dissolved metals in the Zhejiang coastal seawater were investigated. The concentrations of six dissolved metals (i.e. Cu, Pb, Zn, Cd, As and Hg) were in the ranges of 0.10-6.40 (1.6 ± 0.8), 0.16-3.60 (1.2 ± 0.7), 2.50-24.0 (8.5 ± 4.8), 0.011-0.180 (0.07 ± 0.03), 0.85-4.20 (2.1 ± 0.8) and 0.001-0.110 (0.06 ± 0.02) µg/L, throughout the four seasons, respectively. Significant differences in all the dissolved metals were found among seasons, whereas no significant differences were found among stations. The average concentrations of metals were in the following order: Zn > As>Cu > Pb > Cd > Hg. Single metal contamination factor was in the following order: Pb > Hg > Zn > Cu > As>Cd. The pollution level of dissolved metals in the Zhejiang coastal waters (ZCW) was low. Most of the dissolved metals were correlated to temperature, indicating seasonal differences. The redundancy analysis (RDA) indicated that depth, temperature, nitrate and phosphate could best explain the variance pattern of dissolved metals in the ZCW.

Integrated Hydrogeological, Hydrochemical, and Isotopic Assessment of Seawater Intrusion into Coastal Aquifers in Al-Qatif Area, Eastern Saudi Arabia.

Seawater intrusion (SWI) is the main threat to fresh groundwater (GW) resources in coastal regions worldwide. Early identification and delineation of such threats can help decision-makers plan for suitable management measures to protect water resources for coastal communities. This study assesses seawater intrusion (SWI) and GW salinization of the shallow and deep coastal aquifers in the Al-Qatif area, in the eastern region of Saudi Arabia. Field hydrogeological and hydrochemical investigations coupled with laboratory-based hydrochemical and isotopic analyses (18O and 2H) were used in this integrated study. Hydrochemical facies diagrams, ionic ratio diagrams, and spatial distribution maps of GW physical and chemical parameters (EC, TDS, Cl-, Br-), and seawater fraction (fsw) were generated to depict the lateral extent of SWI. Hydrochemical facies diagrams were mainly used for GW salinization source identification. The results show that the shallow GW is of brackish and saline types with EC, TDS, Cl-, Br- concentration, and an increasing fsw trend seaward, indicating more influence of SWI on shallow GW wells located close to the shoreline. On the contrary, deep GW shows low fsw and EC, TDS, Cl-, and Br-, indicating less influence of SWI on GW chemistry. Moreover, the shallow GW is enriched in 18O and 2H isotopes compared with the deep GW, which reveals mixing with recent water. In conclusion, the reduction in GW abstraction in the central part of the study area raised the average GW level by three meters. Therefore, to protect the deep GW from SWI and salinity pollution, it is recommended to implement such management practices in the entire region. In addition, continuous monitoring of deep GW is recommended to provide decision-makers with sufficient data to plan for the protection of coastal freshwater resources.

Integrated seawater intrusion and groundwater quality assessment of a coastal aquifer: GALDIT, geospatial and analytical approaches.

The pressure and dependence on coastal aquifers are on the rise in many parts of the globe. These lead to overexploitation, aggravated levels of groundwater pollution, and seawater intrusion. Integrated analyses can create holistic insights into the quality and the vulnerability of aquifers to seawater intrusion. In this study, Mombasa North coast's coastal aquifer was characterized by integrating multiple approaches-GALDIT overlay index, seawater intrusion groundwater quality index GQISWI, total hardness, water quality index (WQI)-and the results were further explored and interpreted with geospatial analysis techniques. The study suggests that the predominant water type in areas under moderate or high vulnerabilities to seawater intrusion is the Na-Cl water type. However, similar Na-Cl water types can produce a range of total hardness from soft to hard. GQISWI classification can be used to narrow down the observations from Stuyfzand's TH-based classification system. In the aquifer studied, the results of the GALDIT overlay index, a weighted aggregation of intrinsic parameters contributing to seawater intrusion, show that 29%, 59%, and 12% of the aquifer have low, moderate, and high vulnerabilities, respectively. The GQISWI analysis indicates that the groundwater is largely brackish (68%) but saline towards the southern end of the aquifer at 32%. Total hardness values indicate that 67% of the aquifer's coverage falls under the "moderately hard" category. The geodatabase creation introduced in the study provides a template for similar studies and a baseline for future WQI and water quality monitoring. However, temporal studies on chronological timescales are recommended for sustainable management of the aquifer.

Investigation of endocrine disruptor pollutants and their metabolites along the Romanian Black Sea Coast: Occurrence, distribution and risk assessment.

In recent years, the occurrence of organic UV-filters (UVFs) and bisphenol derivatives (BPs) in the marine environment has raised high concerns all over the world, due to the potentially adverse impacts on marine organism and, indirectly on human health. This paper reports, for the first time in Romania, the occurrence, distribution pattern and environmental risk assessment of UVFs, BPs and their metabolites in seawater, sediment and algae collected from the Romania Black Sea coastal region. BP-3 (2-hydroxy-4-methoxy-benzophenone) was the most abundant contaminant in seawater samples, with detection frequency of 100 %. Sediment samples were dominated by ES (Ethylhexyl salicylate), with concentration values up to 5823 ng/g d.w., while for algae, concentrations of several hundreds of ng/g d.w. were determined for BP-3, BS (Benzyl salicylate) and BPE (Bisphenol E). Environmental risk assessment revealed that some UVFs and BPs detected in seawater samples were hazardous to the marine organism of the Black Sea.

A new approach for the determination of sunscreen levels in seawater by ultraviolet absorption spectrophotometry.

Sunscreen is released into the marine environment and is considered toxic for marine life. The current analytical methods for the quantification of sunscreen are mostly specific to individual chemical ingredients and based on complex analytical and instrumental techniques. A simple, selective, rapid, reproducible and low-cost spectrophotometric procedure for the quantification of commercial sunscreen in seawater is described here. The method is based on the inherent properties of these cosmetics to absorb in the wavelength of 300-400 nm. The absorption at 303 nm wavelength correlates with the concentration of most commercial sunscreens. This method allows the determination of sunscreens in the range of 2.5-1500 mg L-1, it requires no sample pretreatment and offers a precision of up to 0.2%. The spectrophotometric method was applied to quantify sunscreen concentrations at an Atlantic Beach with values ranging from 10 to 96.7 mg L-1 in the unfiltered fraction and from the undetectable value to 75.7 mg L-1 in the dissolved fraction. This method is suggested as a tool for sunscreen quantifications in environmental investigations and monitoring programs.

Simultaneous analysis of butyltins and total tin in sediments as a tool for the assessment of tributyltin behaviour, long-term persistence and historical contamination in the coastal environment.

This study presents a new approach for the investigation of tributyltin (TBT) behaviour and fate in the marine environment. The approach is based on a simultaneous analysis of butyltins (BuTs) and total Sn in sediments, thus enabling an assessment of long-term persistence and historical input of TBT. The study also presents first evaluation of the extent to which the TBT-antifouling paints contribute to the contamination of coastal environments with inorganic Sn; it was demonstrated that the inorganic Sn in the investigated areas primarily originates from TBT degradation. The study was conducted by analyzing BuTs and total Sn in sediments from 34 locations along the Croatian Adriatic coast. The results revealed that 85% of the locations were contaminated with both BuTs and inorganic Sn. The share of Æ©BuTs/total Sn was low (<10%) even in sediments with low TBT degradation efficiency (TBT/Æ©BuTs >40%), demonstrating that only small portion of TBT introduced into the water column reached the sediment before being degraded. This means that recent TBT input into the marine environment may be at least 10 times higher than the amount estimated if only BuTs levels in sediments are considered. It was also demonstrated that TBT concentration in sediments with TOC <1% is not a good indicator of the overall pollution level, even if TBT/TOC approach is used in pollution assessment. Finally, in situ investigation showed that resuspension of contaminated sediments leads to significant release of MBT and DBT into the water column, whereas TBT mainly remains in sediment.

A Mesocosm Assessment of the Effect of Bioturbation by the Ghost Shrimp (Lepidophthalmus louisianensis) on the Fate of Petroleum Hydrocarbons in the Intertidal Zone.

To fully assess the long-term impacts of oil spills like the 2010 Deepwater Horizon incident in the northern Gulf of Mexico, the potential for organisms other than microbes to affect the fate and distribution of the oil may have to be considered. This influence could be substantial for abundant bioturbating benthic animals like the ghost shrimp Lepidophthalmus louisianensis. An assessment of the influence of these ghost shrimp on petroleum hydrocarbons was conducted in laboratory micro- and mesocosms containing coastal Gulf of Mexico sediment, seawater, and oil or the polynuclear aromatic hydrocarbon (PAH) pyrene. In an experiment with pyrene added to the water column, the ghost shrimp presence lowered water-column pyrene concentrations. In an experiment with oil added to the sediment surface, the ghost shrimp presence decreased PAH concentrations in the sediment surface layer but increased these in the water column and subsurface sediment. A companion study and a mass-balance analysis indicated a net loss of PAHs through an enhancement of microbial degradation. In an experiment in which oil was added as a narrow subsurface layer in the sediment, the ghost shrimp presence appeared to broaden the oil's depth distribution. Taken together, these results demonstrate that ghost shrimp can significantly influence the biodegradation and distribution of spilled oil in coastal ecosystems. Environ Toxicol Chem 2020;39:637-647. © 2019 SETAC.

Assessment of input of organic micropollutants and microplastics into the Baltic Sea by urban waters.

We assess how different micropollutants and microplastics, connected to wastewater are introduced into the Baltic Sea. The relevance of untreated wastewater, treated wastewater, treated and untreated rain runoff, as well as combined sewer overflow (CSO), is assessed in respect to mass balance, as well as relative inflows of micropollutants and -plastics into the Baltic Sea. To achieve this, modelling based on data on exemplary sewer systems and measured micropollutant concentrations in the single sources were used. Most compounds reach the receiving Baltic Sea via treated wastewater. A few exceptions are compounds that are removed to a very high extent in wastewater treatment plants. For these compounds, the emissions with stormwater (e.g., terbutryn) or untreated wastewater (e.g., triclosan) are dominating. Additionally, compounds that are discharged with the water that is running off urban surfaces are introduced into marine areas via rain runoff. These data are used to forecast a total mass load and concentrations that can be expected in the Baltic Sea. Massloads are expected to be between 0.1 and 5.9 t/a for triclosan and TCPP (tris (2-chloropropyl) phosphate) and 0.2 t/a for microplastic particles. The expected concentrations in open Baltic Sea waters range from 0.01 to 26 ng/L.

Is human health sufficiently protected from chemicals discharged with treated ballast water from vessels worldwide? - A decadal perspective and risk assessment.

Ballast water managements systems (BWMS) installed on vessels may use active substances to inactivate organisms. This paper provides new insights in the global issue of noxious disinfection by-products (DBP) discharge with ballast water, and the related risk assessment for human health. The GESAMP ballast water working group plays a role in the certification process of BWMS that make use of active substances evaluating potential negative effects. We analyzed all BWMS that passed GESAMP final approval over a decade until 2017 providing an overview of chemicals in the discharged ballast water generated by BWMS. We used these data to calculate the chemical load humans may be exposed to for two different commercial ports (Koper, Slovenia and Hamburg, Germany). None of the chemicals in this study reached levels of concern that would indicate a risk for humans after exposure to chemicals present in the discharged ballast water. Nevertheless, although this exposure only adds to a lesser degree to the overall exposure to disinfection by-products, some chemicals, such as tribromomethane, have carcinogenic properties. In case studies we show which chemicals have the largest contribution to the aggregated exposure of humans. We note that tribromomethane, despite its low bio-concentration factor (BCF), may accumulate in fat, when fish are continuously exposed to DBPs during low-level chlorination. Since this figure would give a higher value for the internal dose for tribromomethane from seafood consumption than the current BCF in the GISIS database, the calculated value may underestimate the contribution of tribromomethane, and possibly also other DBPs.

Distribution, sources and ecological risk assessment of PAHs in surface seawater from coastal Bohai Bay, China.

The distribution, composition, potential sources and ecological risk of 16 US EPA priority polycyclic aromatic hydrocarbons (PAHs) were investigated in surface water from coastal Bohai Bay. The PAH concentrations ranged from 48.0 to 607 ng L-1 with the mean value of 267 ng L-1 in dissolved phase and 198 to 935 ng L-1 with the mean value of 424 ng L-1 in particle-associated phase, and decreased following the order: Qinhuangdao (QHD) > Caofeidian (CFD) > Huanghuagang (HHG). The 2-3 ring PAHs accounted for 79.9% to 86.2% in particle-associated phase and 65.6% to 73.2% in dissolved phase of total 16 PAHs, in which naphthalene (Nap) was the most dominant compound. The PAHs in surface seawater mainly originated from petrogenic sources according to the molecular ratios of benzo[a]anthracene/228 and fluoranthene/202. Risk quotients indicated that there was potential ecological risk for PAHs in surface seawater, especially for pyrene and fluorene.

Short-term stability assessment for the analysis of emerging contaminants in seawater.

This paper describes the stability study performed in seawater and seawater extracts (spiked at ~ 200 ng/L) for 23 emerging contaminants. Four different alternatives were tested at six different times (0, 3, 10, 17, 24 and 31 days): (i) seawater at 4 °C, (ii) mixed-mode solid-phase extraction cartridge (Bond Elute Plexa and Strata X-AW) stored at - 20 °C, (iii) polyethersulfone hollow fibre stored at - 20 °C and (iv) methanol extracts once the samples were extracted from PES hollow fibre and stored at - 20 °C. Moreover, the integrity of the supporting polymeric phases was studied by Raman, optical microscopy, differential scanning calorimetric and thermogravimetric analysis. As may be expected, seawater samples showed the lowest stability (losses between 21 and 99%) while methanol extract provides stable results (losses < 30%) over the tested period. In the case of solid-phase cartridges, the stability profile showed an average loss of 7% while, in polyethersulfone hollow fibres, losses up to 58% were observed. Finally, we were able to relate the lower efficiency of polyethersulfone fibres with the wettability of this material based on the thermogravimetric analysis.

Probabilistic ecological risk assessment of heavy metals in western Laizhou Bay, Shandong Province, China.

Considering the serious land-based pollution and the weak water exchange ability of western Laizhou Bay, it is essential to conduct an ecological risk assessment of the pollutants in this area. In this study, the ecological risk caused by heavy metals deposited in the surface sediments and those resuspended in the seawater of western Laizhou Bay was evaluated using probabilistic approaches. First, the concentrations of seven heavy metals, namely As, Cd, Cr, Cu, Hg, Pb, and Zn, in the surface sediments and seawater of western Laizhou Bay were detected during the spring and autumn of 2016. The concentrations of As, Cd, Cr, Cu, and Pb were found to be at levels comparable to those in the other global coastal systems, while those of Hg and Zn were lower than those in other coastal areas. Next, an ecological risk assessment of heavy metals in the surface sediments was performed using a typical potential ecological risk index and refined by using a Monte Carlo simulation. The results suggested low risk for the heavy metals detected in the sediments of western Laizhou Bay, with the exception of Hg in September 2016, which showed a probability (0.03%) of moderate risk. Meanwhile, the aquatic ecological risk assessment of the heavy metals was performed by applying a combination of hazard quotient (HQ) and joint probability curve. While the ecological risk of Cd, Hg, and Pb was found to be acceptable, the HQs for Cr, Cu, and Zn were greater than 1, and the overall risk probability of their adverse effects was higher than 0.05, suggesting certain ecological risk. Specifically, in the case of As, the overall risk probability was lower than 0.05, suggesting that its ecological risk was acceptable, although its HQ was greater than 1. Thus, by applying the probabilistic approaches, the ecological risk of the heavy metals in western Laizhou Bay was better characterized in this study, avoiding both overestimation and underestimation of ecological risk.

Size and shape matter: A preliminary analysis of microplastic sampling technique in seawater studies with implications for ecological risk assessment.

Microplastic particles (MPs) are widely distributed in seawater. Fibrous MPs (microfibres) are often reported as the most commonly encountered shape of particle. To estimate MP concentrations in seawater, samples are often collected using towed nets (generally 300-350-µm mesh) and may underestimate the amount of microfibres present, which may pass through the mesh due to their narrow width. We compared the potential microplastic particle (PMP) concentration estimates provided by two different seawater sampling methods conducted at three commercial shellfish farms and three unfarmed sites in Baynes Sound, British Columbia, Canada. The methods were: 10-L bucket samples sieved through 63-µm mesh in situ and subsequently filtered through an 8-µm polycarbonate membrane; and 1-L bulk samples collected in jars and subsequently filtered to 8 µm. The jar samples yielded PMP concentrations averaging approximately 8.5 times higher than the bucket samples per L of water (at the site level), largely driven by differences in the number of microfibres. There was no significant difference in PNP concentration between shellfish farms and unfarmed sites. An analysis of MP concentrations and mesh sizes reported in the literature suggests that using a 300-350-µm mesh may underestimate total MP concentrations by one to four orders of magnitude compared with samples that are filtered through much smaller mesh sizes (e.g. <100 µm), despite the effect of sample volume. Particles <300 µm in diameter make up a large component of MPs commonly found in fish and invertebrates. As such, common sampling practices fail to adequately measure a biologically relevant class of MPs, thereby undermining the ability to quantify ecological risk. We suggest that seawater sampling methods be designed to filter to <10 µm (the approximate width of many microfibres), either using pressurized pumps for large-volume samples, or by using sufficient replication of small-volume discrete samples.

Improving the biodegradability in seawater test (OECD 306).

Growth and extensive urbanisation of the human population has been accompanied by increased manufacture and use of chemical compounds. To classify the fate and behaviour of these compounds in the environment, a series of international standardised biodegradation screening tests (BSTs) were developed over 30 years ago. In recent years, regulatory emphasis (e.g. REACH) has shifted from measuring biodegradation towards prioritisations based on chemical persistence. In their current guise, BSTs are ineffective as screens for persistence. The marine BST OECD 306 in particular is prone to high levels of variation and produces a large number of fails, many of which can be considered false negatives. An ECETOC funded two-day workshop of academia, industry and regulatory bodies was held in 2015 to discuss improvements to the marine BSTs based on previous research findings from the Cefic LRI ECO11 project and other foregoing studies. During this workshop, methodological improvements to the OECD 306 test were discussed, in addition to clarifying guidance on testing and interpretation of results obtained from marine BSTs (such as pass criteria, lag phases, freshwater read across and complex substances). Methodologically: (i) increasing bacterial cell concentrations to better represent the bacterial diversity inherent in the sampled environments; and (ii) increasing test durations to investigate extended lag phases observed in marine assessments, were recommended to be validated in a multi-institutional ring test.