Novel Low-Cost Sensor for Human Bite Force Measurement.

This paper presents the design and development of a low cost and reliable maximal voluntary bite force sensor which can be manufactured in-house by using an acrylic laser cutting machine. The sensor has been designed for ease of fabrication, assembly, calibration, and safe use. The sensor is capable of use within an hour of commencing production, allowing for rapid prototyping/modifications and practical implementation. The measured data shows a good linear relationship between the applied force and the electrical resistance of the sensor. The output signal has low drift, excellent repeatability, and a large measurable range of 0 to 700 N. A high signal-to-noise response to human bite forces was observed, indicating the high potential of the proposed sensor for human bite force measurement.

Resistance of Hydraulic Calcium Silicate Cements to Dislodgment in Short- and Long-term Assessment.

PURPOSE: To investigate the resistance to dislodgment produced by Biodentine (Septodont) and White-MTA (Angelus) after immersion in phosphate-buffered saline (PBS) for different durations. MATERIALS AND METHODS: Dentin disks 1 ± 0.1 mm thick were obtained from the middle third of the roots of 6 human maxillary canines. On the coronal surface of each dentin disk, four 0.8-mm-diameter holes were drilled. Then the slices were halved using a low-speed saw diamond disk, and the two holes in each half were filled with one of the two tested materials. Each filled half was immersed in PBS solution (pH 7.2) either for 7 days (short term) or 60 days (long term) at 37°C. The push-out test was performed after both time periods. A general linear model (GLM) for repeated measures ANOVA was used to verify the effect of the material and duration of contact with PBS on the push-out strength. The material was considered as the within-subject contrast and the contact duration as the between-subjects effect (p < 0.05). RESULTS: Repeated measures GLM indicated a significant impact of material and time on the push-out strength of the samples (p = 0.000 and p = 0.033, respectively). Biodentine significantly improved the push-out strength compared to MTA at both times (p = 0.000). The lack of significance in the interaction between material and time indicates that PBS immersion positively influenced the push-out values of both tested materials. CONCLUSION: Long-term PBS immersion positively influenced the resistance to dislodgement from dentin of all cements tested. The Biodentine cement provided greater resistance to push-out force than did the MTA.

Assessment of the mechanical properties of ProTaper Next Nickel-titanium rotary files.

INTRODUCTION: The purpose of this study was to compare the torsional resistance, flexibility, and surface microhardness of ProTaper Next files (PTN) with Twisted Files (TF) and RaCe (RC). METHODS: A metal block with a cubical hole was used to evaluate the torsional resistance. Five millimeters of the tip of each file was securely held in place by filling the mold with a resin composite, and the files were driven clockwise at 300 rpm. The number of load applications before fracture was recorded for each file. A scanning electron microscope was used to characterize the topographic features of the fracture surfaces of the broken files. The files were tested for bending resistance by using cantilever-bending test. Vickers microhardness was measured on the cross section of instruments with 300-g load and 15-second dwell time. Torsional resistance data were analyzed by using the nonparametric Kruskal-Wallis and Mann-Whitney U tests. Bending resistance and microhardness data were analyzed by using analysis of variance and Tukey tests. RESULTS: PTN showed the highest torsional resistance and microhardness, followed by RC (P < .05). The fracture cross sections of all brands showed dimpling near the center of fracture surface. The ranking in the bending resistance values was as follows: RC > PTN > TF. CONCLUSIONS: PTN improved its resistance to torsional stresses and wear compared with TF and RC. TF showed improved flexibility compared with other tested brands.

An in-vitro assessment of the shear bond strength of bulk-fill resin composites to permanent and deciduous teeth.

OBJECTIVES: This study aimed to evaluate the shear bond strength (SBS) of bulk-fill resin composites (RCs) to deciduous and permanent teeth. METHODS: The following parameters were investigated: (1) tooth type (deciduous and permanent), (2) tooth substrate (enamel and dentine), (3) restorative material (a high- and a low-viscosity bulk-fill RC and a regular nanohybrid RC as control), and (4) adhesive (two self-etching adhesives). The combination of those parameters resulted in a total of 24 different groups (n=20). Permanent caries-free human molars (240) and deciduous teeth (240) were selected. The bulk-fill RCs (Tetric Evo Ceram Bulk Fill and SureFil SDR) were applied in one 4-mm increment, whereas the regular RC (Tetric Evo Ceram) was layered in two consecutive 2-mm increments. The SBS was examined after storing the specimens for 24 h at 37 °C in distilled water, followed by thermal ageing (5000 cycles between 5 °C and 55 °C). RESULTS: Data were statistically analyzed using one- and multiway analyses of variance and an independent-samples t-test (α=0.05). The multivariate analysis (general linear model with partial eta-squared statistics) tested the influence of the parameters tooth type, tooth substrate, restorative material, and adhesive on the SBS. The parameter tooth type showed no significant impact on the SBS (p=0.576). The influence of the other parameters was significant (p<0.05) but low, and the highest influence was exerted by the parameter adhesive (η(P)(2)=0.120, p=0.0001) followed by tooth substrate (η(P)(2)=0.092, p=0.0001) and restorative material (η(P)(2)=0.028, p=0.0001). The fracture pattern was predominantly adhesive (61.9%) or mixed (38.1), and no cohesive or prefailure was registered. CONCLUSIONS: Bulk-fill materials performed comparable or better than the nanohybrid RC used as control, but the adhesive used was the most relevant factor of influence. This material type might be clinically an option for a faster restoration in both permanent and deciduous teeth. CLINICAL SIGNIFICANCE: Bulk-fill materials performed comparable or slightly better than the nanohybrid RC used as control. Clinically, flowable bulk-fill RCs might be an advantage in restoring deep, narrow cavities, with difficult access angles, whereas larger cavities might be restored easily and faster using high-viscosity compounds.

Assessment of the impact strength of the denture base resin polymerized by various processing techniques.

AIM: To measure the impact strength of denture base resins polymerized using short and long curing cycles by water bath, pressure cooker and microwave techniques. MATERIALS AND METHODS: For impact strength testing, 60 samples were made. The sample dimensions were 60 mm × 12 mm × 3 mm, as standardized by the American Standards for Testing and Materials (ASTM). A digital caliper was used to locate the midpoint of sample. The impact strength was measured in IZOD type of impact tester using CEAST Impact tester. The pendulum struck the sample and it broke. The energy required to break the sample was measured in Joules. Data were analyzed using Student's " t" test. RESULTS: There was statistically significant difference in the impact strength of denture base resins polymerized by long curing cycle and short curing cycle in each technique, with the long curing processing being the best. CONCLUSION: The polymerization technique plays an important role in the influence of impact strength in the denture base resin. This research demonstrates that the denture base resin polymerized by microwave processing technique possessed the highest impact strength.

Maximum dislodging forces of mandibular implant-assisted removable partial dentures: in vitro assessment.

PURPOSE: The initial retention of implant-assisted removable partial dentures (IARPDs) is unknown. The purpose of this in vitro study was to compare maximum dislodging forces of distal extension mandibular IARPD with two different attachments and three clasp designs. MATERIALS AND METHODS: A simulated class I partially edentulous mandible was prepared with two screw-type 3.75 × 12 mm implants in the first molar regions and 2 metal-ceramic crowns on distal abutments. Fifteen bilateral distal extension frameworks were conventionally fabricated in three clasp designs (suprabulge, infrabulge, no clasp). Locator attachments were connected to the 15 denture bases with autopolymerized resin. Each specimen was subject to four types of retention pulls (main, anterior, posterior, unilateral pull) five times with a universal testing machine. Locator attachments were replaced with O-ring attachments, and the same procedure was performed. Therefore, the study groups included: IRPD with Locator attachment and suprabulge clasp (group 1), IRPD with Locator attachment and infrabulge clasp (group 2), IRPD with Locator attachment and no clasp (group 3), IRPD with O-ring attachment and suprabulge clasp (group 4), IRPD with O-ring attachment and infrabulge clasp (group 5), IRPD with O-ring attachment and no clasp (group 6). Data were analyzed using one-way ANOVA, two-way ANOVA, and Tukey tests. RESULTS: The highest mean value was 22.99 lb for prostheses with a Locator attachment and suprabulge clasp. The lowest retentive values were recorded for IARPDs with O-ring attachments. CONCLUSION: The results of this in vitro study suggest that the precise selection of attachments with or without clasp assemblies may affect the clinical success of mandibular IARPDs.

In vitro assessment of three types of zirconia implant abutments under static load.

STATEMENT OF PROBLEM: Although various zirconia abutments have been introduced, insufficient data exist regarding the maximum load capacity of internal tri-channel connection zirconia implant abutments with various implant-abutment interfaces. PURPOSE: The purpose of this in vitro study was to compare the maximum load capacity of 3 different types of internal tri-channel connection zirconia abutments and to assess their mode of failure. MATERIAL AND METHODS: The study investigated 3 groups (n=20) of zirconia implant abutments with different implant-abutment interfaces. Group AllZr consisted entirely of zirconia (Aadva CAD/CAM Zirconia Abutment), group FrZr of a titanium insert friction-fitted to the zirconia abutment component (NobelProcera Abutment Zirconia), and group BondZr of a titanium insert bonded to the zirconia abutment component (Lava Zirconia abutment). All the abutments were thermal cycled for 20 000 cycles between 5°C and 55°C. Sixty test implants made of titanium (Dummy NobelReplace) were embedded in autopolymerizing acrylic resin, and 60 zirconia copings (Lava Zirconia) with a uniform thickness of 2.0 mm were fabricated and bonded to the abutments. A universal testing machine was used to statically load all the specimens at a crosshead speed of 1 mm/min. The maximum load was recorded and used as the failure load. The fractured specimens were collected and representative specimens were studied with a stereomicroscope and scanning electron microscope (SEM). One-way ANOVA and post hoc comparisons with the Tukey HSD tests were used for statistical analysis (α=.05). RESULTS: The mean (SD) maximum load capacity was 484.6 (56.6) N for NobelProcera, 503.9 (46.3) N for Aadva, and 729.2 (35.9) N for Lava abutments. The maximum load capacity of Lava abutments was significantly higher than that of Aadva or NobelProcera (P< 05). No significant difference between Aadva and NobelProcera abutments was noted. The mode of failure among the Aadva, NobelProcera, and Lava abutments was different. CONCLUSIONS: With standard diameter internal tri-channel connection implants, the maximum load capacity of the Lava abutment was significantly higher than that of the Aadva or NobelProcera abutment. No significant difference in maximum load capacity was noted between Aadva and NobelProcera abutments. However, the fracture behavior of all 3 abutments was different.

Assessment of laminate technique using glass ionomer and resin composite for restoration of root filled teeth.

OBJECTIVE: To evaluate the open laminate technique using glass ionomer cements (GIC) in association with a low shrink composite for restoring root filled premolars. METHODS: Extensive MOD cavities plus endodontic access and root filling were performed in intact extracted maxillary premolars. Three restoration types were evaluated: (1) resin composite alone; (2) resin-modified GIC (RM-GIC) open laminate plus resin composite; (3) conventional GIC open laminate plus resin composite (n=8 for all groups and tests). Three tests were conducted to assess restorations: (A) inward cusp deflection during light curing, using DCDTs; (B) fracture strength using a ramped oblique load at 45° to the long axis in a servohydraulic testing machine in comparison with intact and unrestored teeth; (C) proximal marginal leakage using methylene blue dye and the effect of thermocycling. Data were analysed using 1-way ANOVA for cuspal deflection and fracture strength and Fisher's exact test for leakage. RESULTS: Laminate restorations resulted in significantly less cuspal deflection compared with resin composite (4.2±1.2 µm for RM-GIC and 5.1±2.3 µm for conventional GIC vs. 12.2±2.6 µm for composite, P<0.001). Fracture strength was not significantly different among all groups. Failure with all restorations was predominantly adhesive at the tooth-restoration interface. The two laminate groups showed significantly better marginal seal than composite alone, but sealing ability of conventional GIC deteriorated after thermocycling. CONCLUSIONS: Laminate restoration of root filled teeth had beneficial effects in terms of reducing cuspal deflection and marginal seal, with acceptable fracture strength.

An in vitro assessment of circumferential grooves on the retention of cement-retained implant-supported crowns.

STATEMENT OF PROBLEM: Crowns cemented on short implant abutments may have insufficient retention. PURPOSE: The purpose of this study was to evaluate the effect of circumferential grooves on the retention of cemented cast copings on implant abutments. MATERIAL AND METHODS: Sixty similarly-shaped implant abutments were divided into 4 groups (n=15): without grooves, with 1 groove, with 2 grooves, and with 3 grooves. Fifteen identical NiCr cast copings were prepared to fit all 60 abutments. The castings were cemented to each group of abutments with a noneugenol provisional cement (Tempbond NE) and a zinc phosphate cement (Harvard). After thermal cycling and storage for 6 days in a water bath, retention tests were conducted with a tensile testing machine (Instron) (5 mm/min) and retentive forces were recorded. Data were subjected to 1 way-ANOVA, Tukey's (HSD) test, and repeated measures ANOVA (α=.05). RESULTS: For the noneugenol temporary cement, group retention values were increased according to the number of grooves (P<.001). For the zinc phosphate cement, the first groove increased the retention by approximately 60% (P<.001). The retentive values were higher for the zinc phosphate cement than the provisional cement. The influence of the grooves depended on the type of cement used (P<.001). Cement remnants were found primarily on the castings for provisional cement and for the plain abutments cemented with zinc phosphate cement. Remnants were found primarily on the abutments for the grooved abutments cemented with zinc phosphate cement. CONCLUSIONS: The addition of circumferential grooves to implant abutments increased the retention of cement-retained castings. For zinc phosphate cement, 1 groove was as effective as several, whereas for the provisional cement, the retention increased gradually with additional grooves.

New palpometer with implications for assessment of deep pain sensitivity.

The aims of this study were to compare test-retest variability and accuracy measures between (1) manual palpation and a novel palpometer and (2) different force levels. Sixteen clinicians were instructed to target 0.5, 1.0, and 2.0 kg on a force meter using manual palpation and the new palpometer (adjustable spring-coil with a small pin touching the examiner's hand when the correct pressure is reached). In all experiments, 10 consecutive measures of the force levels were recorded. The coefficient of variation (CV), actual force levels, and relative differences between target level and actual force level were compared between experiments and target levels. All outcome parameters had significantly lower values for the new palpometer than for manual palpation in a force-dependent manner (p<0.004). CVs and actual force levels were significantly different between all target levels (p<0.004). The new palpometer had low test-retest variability and provides a more accurate pressure stimulus than manual palpation.

Implant stability and bone density: assessment of correlation in fresh cadavers using conventional and osteotome implant sockets.

OBJECTIVE: To compare the primary stability of implants placed in conventional and osteotome sites and to evaluate the level of correlation between cutting torque measurements, resonance frequency analysis (RFA), and bone density. MATERIALS AND METHODS: Eight human femoral heads were scanned with computed tomography for bone density measurements as Hounsfield units (HU), and individualized computed tomography-based surgical stents were prepared for placement of implants. Five implant sockets were prepared in each collum (CoF), caput (CaF), and trochanter (Tr-MM) section of the femoral heads using the conventional drilling technique or by a combination of drilling and use of an osteotome. Cutting-torque values (CTV) of the implants were measured by a manual torque wrench, followed by determination of implant stability quotients (ISQ) by RFA. RESULTS: The CTVs of implants were similar in the conventional group, but different in the osteotome group (P<0.05). There was a general tendency toward achieving higher CTV and ISQ values in CoF than CaF and Tr-MM (P<0.05), and measurements in CaF and Tr-MM were comparable (P>0.05). The mean HU of sites were similar, although CoF had higher HU values (P>0.05). CTV of implants in CaF and Tr-MM and ISQ values in CoF in the conventional groups were higher than those in the osteotome groups (P<0.05). The correlation between CTV and HU in Tr-MM was significant in the osteotome group, although no other correlations between CTV, ISQ, and HU could be detected (P>0.025). CONCLUSIONS: Conventional placement led to higher implant stability than the drilling and osteotome technique used in the study. No correlation could be found between CTV, RFA, and bone density.

Assessment of polymerization contraction stress of three composite resins.

OBJECTIVES: The purpose of this study was to measure the development of contraction stress of three composite resin restorative materials during photo-polymerization: a micro-hybrid composite (Filtek Z250, 3M ESPE, St. Paul, MN, USA); a nano-filled composite (Filtek Supreme, 3M ESPE, St. Paul, MN, USA); and a low-shrinkage composite (AElite LS, Bisco Inc., Schaumburg, IL, USA). METHODS: Curing shrinkage stress was measured using a stress-analyzer. Composites were polymerized with a halogen-curing unit (VIP, Bisco Inc., Schaumburg, IL, USA) for 40 s. The contraction force (N) generated during polymerization was continuously recorded for 150 s after photo-initiation. Contraction stress (MPa) was calculated at 20, 40, 60 and 150 s. Data were statistically analyzed. RESULTS: The low-shrinkage composite AElite LS exhibited the lowest stress values compared to other materials (p<0.05). Statistical analysis did not show significant differences between Filtek Z250 and Filtek Supreme. SIGNIFICANCE: The low-shrinkage composite showed lower contraction stress than micro-hybrid and nano-filled composite. Ideally, non-shrinking resins would represent the ultimate solution to overcome polymerization contraction and stress-related problems.

Clinical assessment of chewing function of obturator prosthesis wearers by objective measurement of masticatory performance and maximum occlusal force.

PURPOSE: Eating, which includes chewing and swallowing, is an oral function that influences quality of life. Though the swallowing ability of maxillectomy patients was reported in our previous study, the chewing function has not been fully reported to date. Thus, the purpose of this study was to evaluate the chewing function of obturator prosthesis wearers by measurement of masticatory performance and occlusal force. The relationship of these 2 measurements was also investigated. MATERIALS AND METHODS: Twenty maxillofacial obturator prosthesis wearers undergoing periodic checkup at the maxillofacial rehabilitation clinic in Kyushu University Hospital were recruited for this study. Additionally, 20 young, healthy individuals were recruited as controls. Data on masticatory performance, which was measured by a sieve method using hydrocolloid material, and maximum occlusal force, which was measured by the Dental Prescale System (Fuji Film), were obtained for each participant. RESULTS: The mean of masticatory performance was 2.6 (SD 1.2) on a 1.40-mm mesh. There was no significant difference in masticatory performance between the patient group and the controls. The mean maximum occlusal force of the patient group was 625.9 N (SD 299.1 N), which was significantly lower than that of the control group. There was no significant correlation between masticatory performance and maximum occlusal force for the patient group in this study (P = .3726). CONCLUSION: Masticatory performance of obturator prosthesis wearers with dentate or partially edentulous maxillae was not different from that of young, healthy individuals, though maximum occlusal force of these patients was lower than that of controls.

Dynamometric assessment of the mechanical resistance of porcelain veneers related to tooth preparation: a comparison between two techniques.

STATEMENT OF PROBLEM: There is little agreement regarding a palatal extension of the preparation for porcelain veneers, as it represents a more invasive technique than a preparation limited to the facial surface of a tooth. PURPOSE: The purpose of this study was to detect the stress in maxillary anterior teeth restored with porcelain veneers and compare the resistance to fracture of porcelain veneers prepared using different preparation designs. MATERIAL AND METHODS: Forty-five maxillary anterior teeth were restored with porcelain veneers and divided into 9 groups as follows: Ca, canines with no preparation; Ca-Ch, canines with palatal chamfer preparation; Ca-W, canines with window preparation; LI, lateral incisors with no preparation; LI-Ch, lateral incisors with palatal chamfer preparation; LI-W, lateral incisors with window preparation; CI, central incisors with no preparation; CI-Ch, central incisors with palatal chamfer preparation; CI-W, central incisors with window preparation. Shear-flexural fracture tests were performed. The fractured specimens were subjected to scanning electron microscope (SEM) analysis. Data were statistically analyzed with univariate analysis of variance and the Tukey post hoc test for multiple comparisons (alpha=.05). RESULTS: The following mean fracture load values (N) were recorded: Ca, 395 +/- 6; Ca-Ch, 310 +/- 8; Ca-W, 322 +/- 8; LI, 309 +/- 8; LI-Ch, 242 +/- 6; LI-W, 225 +/- 8; CI, 298 +/- 8; CI-Ch, 255 +/- 8; CI-W, 221 +/- 6. The SEM analysis showed that both adhesive and cohesive fractures were primarily concentrated at the cervical region. Statistical analysis showed that both the type of tooth and the design of the preparation significantly influenced the resistance to fracture of the restored teeth (P<.001). CONCLUSION: The chamfer preparation is recommended for central incisors, whereas the window preparation showed better results for canines. Both preparations can be adopted in the restoration of lateral incisors.

Resonance frequency analysis and damping capacity assessment. Part I: an in vitro study on measurement reliability and a method of comparison in the determination of primary dental implant stability.

OBJECTIVES: The aims of this in vitro study were to evaluate reliability of the Osstell and Periotest devices in the assessment of implant stability and to perform a method comparison. MATERIAL AND METHODS: Commercial dental implants were inserted into bovine rib segments of different anatomical origins and densities. Repeated measurements were performed, varying (a) the torque-in force of the devices' attachment screw (the Osstell transducer and the ball attachment, insert for the Periotest device), (b) the insertion site bone quality, and (c) the thread exposure in simulated peri-implant bone defects. RESULTS: Both methods were comparably reliable and showed a strong association to each other in the classification of implant stability. As opposed to torque-forced screw attachment, the variations in bone composition, differences in inter-implant stability of adjacent implants, and peri-implant bone reduction were statistically significant for both methods. CONCLUSIONS: Both non-invasive diagnostic devices seem to be useful in the long-term follow-up of implant integration.

Resonance frequency analysis and damping capacity assessment. Part 2: peri-implant bone loss follow-up. An in vitro study with the Periotest and Osstell instruments.

OBJECTIVE: We compared the performance of damping capacity assessment (Periotest device) to resonance frequency analysis (Osstell device) in the assessment of peri-implant bone loss in an in vitro experiment. MATERIAL AND METHODS: Screw-type oral implants were polymerized into acrylic blocks. Peri-implant bone loss was simulated by successively removing defined portions of material surrounding the implants in millimeter increments. Measurement values of both devices were compared by assessing the associated measurement errors, by calculating correlation analyses and drawing scatterplots, and by means of regression analysis referring to increasing bone loss. RESULTS: Both devices produced comparable results suggesting agreement of the measured implant stability values to the actual loss of peri-implant resin. There was a noticeable correlation of the Periotest and Osstell implant stability values. CONCLUSION: The results of this experiment suggest agreement in predicting the actual implant stability with both the instruments with the Osstell instrument being the more precise device.

Assessment of flexural strength and color alteration of heat-polymerized acrylic resins after simulated use of denture cleansers

O objetivo deste estudo foi avaliar a resistência à flexão e alterações de cor de resinas acrílicas termopolimerizáveis imersas em higienizadores de prótese por diferentes períodos de tempo. Corpos-de-prova retangulares (65x10x3mm) de três resinas acrílicas (Lucitone 550, QC-20 e Triplex) foram divididos em três grupos de higienizadores de prótese (Bony Plus, Corega Tabs e Efferdent Plus) e um grupo controle (imersão em água). Foram realizadas imersões por 15 min e 8 horas, simulando 30 dias de uso. O teste de resistência à flexão foi realizado com 105 corpos-de-prova em máquina de ensaios universais. Alterações de cor foram avaliadas por meio de fotografias tiradas de 21 corpos-de-prova. Os resultados de resistência à flexão (em MPa) foram submetidos à análise de variância e teste de Tukey, com nível de significância de 5%. Houve diferenças significantes (p<0.01) entre as resinas Lucitone (89,439 ± 7,962); Triplex (88,024 ± 5,167) and QC-20 (83,379 ± 7,153). Não foram encontradas diferenças significantes (p>0.05) entre os higienizadores de prótese (Bony Plus = 87,693 ± 6,943; Corega Tabs = 86,955 ± 7,114; Efferdent Plus = 86,195 ± 7,865; e controle = 86,536 ± 7.012) nem entre os períodos de imersão (15 min = 86,875 ± 7,625 e 8 h = 87,432 ± 7,355) durante os ciclos de imersão que simularam 30 dias de uso. A inspeção visual não detectou qualquer alteração de cor. Os achados desse estudo revelaram que os higienizadores de prótese, quando usados de acordo com as instruções dos fabricantes, não afetaram a resistência à flexão nem causaram alterações de cor nas resinas acrílicas termopolimerizáveis após um período de uso simulado de 30 dias.

Assessment of flexural strength and color alteration of heat-polymerized acrylic resins after simulated use of denture cleansers.

The purpose of this study was to assess flexural strength and color alteration of acrylic resins immersed in denture cleansers for different periods of time. Rectangular specimens (65 x 10 x 3mm) made from three heat-polymerized acrylic resins (Lucitone 550, QC-20 and Triplex) were assigned to three denture cleansers groups (Bony Plus, Corega Tabs and Efferdent Plus) and a control group (immersion in water). Soaking trials of 15 min and 8 h simulated 30 days of use. Flexural strength testing was carried out with 105 specimens on a universal testing machine. Color alterations were visually assessed by examination of photographs taken from 21 specimens. Flexural strength means (in MPa) were analyzed statistically by analysis of variance and Tukey's test at 5% significance level. There were significant differences (p<0.01) among the resins Lucitone (89.439 +/- 7.962), Triplex (88.024 +/- 5.167) and QC-20 (83.379 +/- 7.153). No significant differences (p>0.05) were found either among the denture cleansers (Bony Plus = 87.693 +/- 6.943; Corega Tabs = 86.955 +/- 7.114; Efferdent Plus = 86.195 +/- 7.865 and control = 86.536 +/- 7.012) or between the soaking periods (15 min = 86.875 +/- 7.625 and 8 h = 87.432 +/- 7.355) throughout the soaking cycles simulating 30 days of use. No color alterations were identified by visual examination. The findings of this study showed that chemical denture cleansers used according to the manufacturers' specifications did not cause flexural strength alterations or color changes in heat-polymerized acrylic resins submitted to soaking cycles that simulated 30 days of use.

A biologic model for assessment of osseous strain patterns and plating systems in the human maxilla.

PURPOSE: This study was conducted to examine a biomechanical model and to help answer fundamental questions that relate to rigid plate fixation in the maxilla. Specifically, we sought to elucidate the principal strain patterns generated in the maxilla secondary to masticatory forces as well as the amount of permanent deformational changes incurred due to these loading forces. MATERIALS AND METHODS: Cadaveric heads with the mandible removed were defleshed and placed in a 2-part testing rig to hold and position the skull for testing in a standard material testing system. Rosette strain gages were attached at predefined points on the skull, and an Instron machine was used to load the skull through the loading port on the tray. A Le Fort I osteotomy was then performed on the skull, and a Walter Lorenz Ultra-Micro plating system was applied by a surgeon to reconnect the upper jaw. A 2-mm gap was left at the line of the osteotomy, and a transducer was attached to measure closure of the gap. Again the skull was loaded with the Instron (Canton, MA) machine. RESULTS: The results indicate a linear relationship exists with both maximum (tensile) and minimum (compressive) strain patterns relative to incremental load placement on the intact maxilla. The strain patterns after the Le Fort I osteotomy and plating were different and less linear. The differential variable reluctance transducer data showed a low rate of closure or transient increase in the gap at low loads (0 to 15 kilopond [kp] range) and a steeper slope of closure during high loads (15 to 60 kp range). It is also evident that axial loading forces cause permanent deformation and failure of osseous plating systems predominantly through bending. CONCLUSIONS: This model provides a foundation of knowledge regarding biomechanical strains in the maxilla subjected to static compressive loads in the force range of mastication. In addition, it serves as a comparative reference to assess rigidity of various craniofacial plating systems and to validate proposed standardized synthetic models. With the advent of increasingly precise surgery and new plating systems, this model can be used to help guide placement and design of plating systems; thereby allowing for ideal stabilization and optimizing surgical outcome.

In vitro assessment of the mechanical properties of latex and non-latex orthodontic elastics.

The increased incidence of latex allergies has led to the development of non-latex orthodontic products. The purpose of this study was to compare the mechanical properties of latex and non-latex orthodontic elastics. The elastics tested were from 2 manufacturers (GAC and Masel) and made of 2 materials (latex and non-latex). The properties tested included cross-sectional area, breaking force, peak load, peak stress, stiffness, modulus, hysteresis, and 24-hour load relaxation. The data were analyzed with 1-sample t tests, an analysis of variance, and the Fisher PLSD test. Between GAC and Masel, the GAC non-latex elastics had greater breaking forces than did the Masel non-latex elastics. The Masel latex elastics had greater breaking forces than did the Masel non-latex elastics. The GAC non-latex elastics showed more viscoelastic properties than both the GAC latex elastics and the Masel non-latex elastics; however, the Masel elastics were more viscoelastic than the GAC elastics. Forces generated by the elastics decreased over 24 hours to an average load approximating 75% of the manufacturers' values (GAC latex, Masel latex, and Masel non-latex elastics) and to 60% for the GAC non-latex elastics. The mechanical properties of the non-latex elastics were not comparable to those of the latex elastics. Therefore, the clinical choice of elastics should be based on the patient's medical history and the specific mechanical properties of the type of elastic.