Profiling and potential cancer risk assessment on children exposed to PAHs in playground dust/soil: a comparative study on poured rubber surfaced and classical soil playgrounds in Seoul.

Children can get affected by polycyclic aromatic hydrocarbons (PAHs) while they interact with play area soil/rubber surfacing and exposed to PAHs by dermal contact, inhalation and hand-to-mouth activity. A comparative study has been conducted on PAHs profiling and probable cancer risk of children from PAHs present in uncovered playground surface soil and poured rubber surfaced playground dust. Surface soil and dust samples have been collected from 14 different children parks around the Korea University campus, Seoul, Republic of Korea. Concentrations of 16 PAHs in the soils/dust were found to be in a range of 2.82-57.93 µg g-1. Profiling of the PAHs from the playground soils/dust reveals 3-ring PAHs are dominating with 79.9% of total PAHs content, on an average. The diagnostic ratio analysis confirms that vehicular exhaust and fossil fuel burning are likely the main sources of high molecular weight carcinogenic PAHs, whereas low molecular weight PAHs have pyrogenic origin. The probabilistic health risk assessment using Monte Carlo simulations for the estimation of the 95% cancer risk exposed to the PAHs from the surfaced playgrounds shows a little higher value than the USEPA safety standard (1.3 × 10-5). Sensitivity analysis revealed exposure duration and relative skin adherence factor for soil as the most influential parameters of the assessment. Noticeably, cancer risk is approximately 10 times higher in poured rubber surfaced playgrounds than in uncovered soil playgrounds.

Tire waste management system in Cyprus in the framework of circular economy strategy.

Worldwide, waste raised from tires counts 1.3-1.5 billion tonnes/year and by the end of 2025, is expected to be more than 2.5 billion tonnes. On 2013, the EU countries reached 3.6 million tonnes of used tires. However, the cheapest treatment method since now is landfilling and is considered to be a major threat for the environment and the public health. In Cyprus, the total tires that were imported on 2015 was 835,142 pieces (5.8% more than the 2014), which were equal to 9638 t, while at the same time, the total waste from those tires were 6629 tonnes. Moreover, the cement industry used 6691 tonnes of tires as alternative fuel. Until now, there are three management systems in place in Cyprus, for the end-of-life tires (ELTs). The collection of ELTs on 2011 was 1817 tonnes while at the end of 2016 was 7201 tonnes. The main treatment methods in Cyprus are the use of ELTs as alternative fuel in cement industry or to produce rubber granules (609-2738 tonnes/year) to be used to construct artificial surfaces or substrate for artificial lawn grounds and limited to pyrolysis (324-837 tonnes/year). At the same time, the environmental fees for the collection of tires varies and depends on the tire category. Furthermore, the market share of ELTs is up to 1.5 million € and the total recovery index from the market is closed to 90% the last 6 years (2013-2017). This paper evaluates and assess the existing tire waste management system (TWMS) in Cyprus in order to promote strength and weakness as well as to propose a holistic management system in insular communities in order to adopt the targets set by the concept of circular economy. The SWOT analysis identified as the main weaknesses the absence from the legislation of specific target for the recovery index of tires and the absence of any centralized logistic system to control the existing management systems while the main threats includes bureaucracy and the absence of technical and economic data which will guarantee the financial viability of a centralized treatment unit.

Assessment of Patient Exposure to Leachables From Lyophilized Drug Formulations Following Reconstitution, Storage, and Administration via Polymeric Packaging/Delivery Systems.

It has been demonstrated that lyophilized drug formulations have an increased propensity to leach substances from the rubber stoppers comprising their primary packaging system when compared to aqueous liquid formulations stored in the same manner. Unfortunately, patient exposure to leachables originating in lyophilized drug products is not known. To that end, the goal of this study was to assess patient exposure to these leachables after reconstitution, storage, and administration of the lyophilized drug. To achieve this goal, several leachables present in 2 commercial lyophilized drug products were quantified after contact with polyvinyl chloride and non-polyvinyl chloride medication bags as well as an infusion set for durations of 15 min to 7 days at refrigerated and ambient temperature. The results obtained from this study showed that the bag's material of construction and the drugs formulation did not impact the mass of the leachables administered. Conversely, the mass of each leachable administered to the patient was reduced or eliminated as the contact duration with the intravenous bag and the temperature increased. However, for shorter contact durations, refrigerated storage, and higher molecular weight compounds, the patient would be exposed to a majority of the leachables originating from the vial.

Assessment of Semi-Quantitative Health Risks of Exposure to Harmful Chemical Agents in the Context of Carcinogenesis in the Latex Glove Manufacturing Industry.

Excessive exposure to chemicals in the workplace can cause poisoning and various diseases. Thus, for the protection of labor, it is necessary to examine the exposure of people to chemicals and risks from these materials. The purpose of this study is to evaluate semi-quantitative health risks of exposure to harmful chemical agents in the context of carcinogenesis in a latex glove manufacturing industry. In this cross-sectional study, semi-quantitative risk assessment methods provided by the Department of Occupational Health of Singapore were used and index of LD50, carcinogenesis (ACGIH and IARC) and corrosion capacity were applied to calculate the hazard rate and the biggest index was placed as the basis of risk. To calculate the exposure rate, two exposure index methods and the actual level of exposure were employed. After identifying risks, group H (high) and E (very high) classified as high-risk were considered. Of the total of 271 only 39 (15%) were at a high risk level and 3% were very high (E). These risks only was relevant to 7 materials with only sulfuric acid placed in group E and 6 other materials in group H, including nitric acid (48.3%), chromic acid (6.9%), hydrochloric acid (10.3%), ammonia (3.4%), potassium hydroxide (20.7%) and chlorine (10.3%). Overall, the average hazard rate level was estimated to be 4 and average exposure rate to be 3.5. Health risks identified in this study showed that the manufacturing industry for latex gloves has a high level of risk because of carcinogens, acids and strong alkalisand dangerous drugs. Also according to the average level of risk impact, it is better that the safety design strategy for latex gloves production industry be placed on the agenda.

Evaluation of Quantitative Exposure Assessment Method for Nanomaterials in Mixed Dust Environments: Application in Tire Manufacturing Facilities.

Current recommendations for nanomaterial-specific exposure assessment require adaptation in order to be applied to complicated manufacturing settings, where a variety of particle types may contribute to the potential exposure. The purpose of this work was to evaluate a method that would allow for exposure assessment of nanostructured materials by chemical composition and size in a mixed dust setting, using carbon black (CB) and amorphous silica (AS) from tire manufacturing as an example. This method combined air sampling with a low pressure cascade impactor with analysis of elemental composition by size to quantitatively assess potential exposures in the workplace. This method was first pilot-tested in one tire manufacturing facility; air samples were collected with a Dekati Low Pressure Impactor (DLPI) during mixing where either CB or AS were used as the primary filler. Air samples were analyzed via scanning transmission electron microscopy (STEM) coupled with energy dispersive spectroscopy (EDS) to identify what fraction of particles were CB, AS, or 'other'. From this pilot study, it was determined that ~95% of all nanoscale particles were identified as CB or AS. Subsequent samples were collected with the Dekati Electrical Low Pressure Impactor (ELPI) at two tire manufacturing facilities and analyzed using the same methodology to quantify exposure to these materials. This analysis confirmed that CB and AS were the predominant nanoscale particle types in the mixing area at both facilities. Air concentrations of CB and AS ranged from ~8900 to 77600 and 400 to 22200 particles cm(-3), respectively. This method offers the potential to provide quantitative estimates of worker exposure to nanoparticles of specific materials in a mixed dust environment. With pending development of occupational exposure limits for nanomaterials, this methodology will allow occupational health and safety practitioners to estimate worker exposures to specific materials, even in scenarios where many particle types are present.

Assessment of the hemolysis and endothelial cell cytotoxicity induced by residual linear alkylbenzene sulfonates on pharmaceutical rubber stoppers based on HPLC-ESI-MS.

This study was designed to develop a high-performance liquid chromatographic-electrospray ionization-mass spectrometry (HPLC-ESI-MS) method for quantitative determination of residual surfactant linear alkylbenzene sulfonate (LAS) compounds on pharmaceutical rubber stoppers. An HPLC-ESI-MS method was developed for separation and determination of five LAS homologs (C10-C14) under gradient conditions using methanol and ammonium acetate as mobile phases. Hemolysis activity of residual LAS compounds was analyzed by spectrophotometry. Expression of interleukin (IL)-6 and tumor necrosis factor (TNF)-α in human umbilical vein endothelial cells (HUVECs) after LAS compound treatment was examined by enzyme-linked sorbent assay. LAS compounds were well separated and determined by the established gradient conditions. The linear range was 0.05-8 µg/mL with correlation coefficients ≥0.997. Recoveries were from 73 to 134% and the relative standard deviation was <13.7%. There was a correlation between hemolysis rate and LAS compounds concentration when it was ≥0.8 µg/cm(2). LAS compounds decreased the viability of HUVECs and promoted the production of IL-6 and TNF-α. The developed analytical method was successful for quantitative determination of residual LAS compounds on pharmaceutical rubber stoppers and it is important to monitor and control the amount of LAS compounds on rubber stoppers.

Resource recovery from end-of-life tyres in Greece: a field survey, state-of-art and trends.

Lack of consistent and available information for the entire tyre industry has often hindered adequate understanding of current and future issues that need to be addressed for improving the sustainable end-of-life tyre management. The aim of this paper is to review related best available technologies and techniques for Greece, ranging from simple mechanical processing, up to complex multistep, mechanochemical and/or thermal treatment. End-of-life tyre management guidelines in the form of a manual for supporting future entrepreneurs in this field are also discussed. Extensive data mining, classification and inventorying was performed, both in the field via questionnaires and in the literature, for the purpose of accurately determining Hellenic conditions, in order to pinpoint encountered problems, propose interventions and determine new entrepreneurship opportunities.

Toxicity assessment of sequential leachates of tire powder using a battery of toxicity tests and toxicity identification evaluations.

Approximately 460,000 ton of rubber are dispersed annually along the European roads due to tire wear. Tire rubber is known to leach compounds that are toxic to aquatic organisms. However, the potential effects of tire wear material on aquatic organisms at environmental relevant concentrations, and over time have so far not been extensively studied. In this study, rubber from three different tires was abraded and the powder leached in deionised water. The rubber powder was leached six times sequentially. All leachates were tested for toxicity using standardized toxicity tests including green algae (Pseudokirchneriella subcapitata, 72h growth inhibition), crustaceans (Daphnia magna, 24 and 48h immobility and Ceriodaphnia dubia, 48h survival and 9d reproduction and survival), and zebra fish eggs (Danio rerio, 48h lethality). The reproduction of C. dubia was the most sensitive endpoint tested, with an EC50 of 0.013 g L(-1) up to the third leaching of the most toxic tire, which is similar to a predicted concentration in road runoffs. The toxicity of all tires was reduced by the sequential leachings and after the sixth leaching the EC50s were >0.1 g L(-1) for all endpoints. Toxicity identification evaluations indicated that the toxicity was caused by zinc and organic compounds.

[Assessment of the occupational risk to workers engaged in the manufacture of divinyl-styrene rubber]. / Otseniavane profesionalniia risk na rabotnitsi, zaeti v proizvodstvoto na divinil-stirolov kauchuk.

The production of synthetic rubber, one of the varieties of petro-chemical branch in our country, is new and very prospective. The Bulgarian synthetic rubber is synthesized from petroleum products divinyl and styrene. After the hygienic assessment of the technological processes, a complete characteristic of labour conditions was made and the character of the working process was studied of the main occupations of the workers, attending the installations of Synthetic Rubber Plant. The exposure to occupational noxae was determined and the existing occupational risk was evaluated. The toxico-chemical substances, benzene, styrene and divenyl, are with the highest significance among the factors of the working environment. The data on the health state of the workers are reported and recommendations are proposed for the restriction of the effect of the occupational factors.