Assessment of Adaptability and Linear Dimensional Changes of Two Heat Cure Denture Base Resin with Different Cooling Techniques: An In Vitro Study.

AIM: The current study was designed to assess the linear dimensional changes and adaptability of two heat-cured denture base resins using various cooling methods. MATERIALS AND METHODS: To prepare a total of 90 acrylic resin samples (45 acrylic resin samples for each material), four rectangular stainless-steel plates measuring 25 × 25 × 10 mm were fabricated. For both groups, the material was put into the mold at the dough stage. Group I - SR Triplex Hot Heat Cure acrylic; group II - DPI Heat Cure acrylic. Both groups used the same curing procedure. One of the following three techniques was used to cool the material (15 samples from each material) once the curing cycle was finished: (A) water bath, (b) quenching, and (C) air. A traveling microscope was used to measure the distance between the markings on the acrylic samples. The data was recorded and statistically analyzed. RESULTS: In SR Triplex Hot heat cure acrylic material, the maximum linear dimensional changes were found in the quenching technique (0.242 ± 0.05), followed by the air technique (0.168 ± 0.11) and the least was found in the water bath technique (0.146 ± 0.01). In DPI Heat Cure acrylic material, the maximum linear dimensional changes were found in the quenching technique (0.284 ± 0.09), followed by the air technique (0.172 ± 0.18) and the least was found in the water bath technique (0.158 ± 0.10). There was a statistically significant difference found between these three cooling techniques. On comparison of adaptability, the water bath technique, the marginal gap SR Triplex Hot was 0.012 ± 0.02 and DPI Heat Cure was 0.013 ± 0.02. In the quenching technique, the marginal gap SR Triplex Hot was 0.019 ± 0.04 and DPI Heat Cure was 0.016 ± 0.04. In the air technique, the marginal gap SR Triplex Hot was 0.017 ± 0.01 and DPI Heat Cure was 0.019 ± 0.01. CONCLUSION: The present study concluded that among the different cooling methods, the water bath technique had the least linear dimensional change, followed by the air and quenching techniques. When comparing the materials, DPI Heat Cure acrylic resin showed a greater linear dimensional change than SR Triplex Hot heat cure acrylic resin. CLINICAL SIGNIFICANCE: During polymerization, heat-cured acrylic resins experience dimensional changes. Shrinkage and expansion are dimensional changes that occur in heat-cured acrylic resins and have an impact on the occlusal relationship and denture fit. However, the denture base's material qualities and the different temperature variations it experiences during production may have an impact on this. How to cite this article: Kannaiyan K, Rathod A, Bhushan P, et al. Assessment of Adaptability and Linear Dimensional Changes of Two Heat Cure Denture Base Resin with Different Cooling Techniques: An In Vitro Study. J Contemp Dent Pract 2024;25(3):241-244.

Dental implant and abutment in PEEK: stress assessment in single crown retainers on anterior region.

OBJECTIVE: Stress distribution assessment by finite elements analysis in poly(etheretherketone) (PEEK) implant and abutment as retainers of single crowns in the anterior region. MATERIALS AND METHODS: Five 3D models were created, varying implant/abutment manufacturing materials: titanium (Ti), zirconia (Zr), pure PEEK (PEEKp), carbon fiber-reinforced PEEK (PEEKc), glass fiber-reinforced PEEK (PEEKg). A 50 N load was applied 30o off-axis at the incisal edge of the upper central incisor. The Von Mises stress (σvM) was evaluated on abutment, implant/screw, and minimum principal stress (σmin) and maximum shear stress (τmax) for cortical and cancellous bone. RESULTS: The abutment σvM lowest stress was observed in PEEKp group, being 70% lower than Ti and 74% than Zr. On the implant, PEEKp reduced 68% compared to Ti and a 71% to Zr. In the abutment screws, an increase of at least 33% was found in PEEKc compared to Ti, and of at least 81% to Zr. For cortical bone, the highest τmax values were in the PEEKp group, and a slight increase in stress was observed compared to all PEEK groups with Ti and Zr. For σmin, the highest stress was found in the PEEKc. Stress increased at least 7% in cancellous bone for all PEEK groups. CONCLUSION: Abutments and implants made by PEEKc concentrate less σvM stress, transmitting greater stress to the cortical and medullary bone. CLINICAL RELEVANCE: The best stress distribution in PEEKc components may contribute to decreased stress shielding; in vitro and in vivo research is recommended to investigate this.

Assessment of the trueness of additively manufactured mol3% zirconia crowns at different printing orientations with an industrial and desktop 3D printer compared to subtractive manufacturing.

OBJECTIVES: This study endeavours to investigate the effect of printing orientation on the trueness of additively manufactured molar zirconia crowns. The areal surface roughness and the characteristics of the marginal regions of the crowns were also considered. METHODS: Twelve molar crowns were manufactured at 0°, 45°, and, 90° printing orientations in a Lithoz and AON zirconia printer, respectively. Twelve milled crowns were used as a comparison. Samples were scanned and analysed in metrology software to determine the trueness of the groups. Regions of interest were defined as the margins, intaglio surface and contact points. Areal surface roughness and print layer thickness were further analysed using a confocal laser scanning microscope. RESULTS: The results indicate that there are clear differences between the investigated desktop (AON) and industrial (Lithoz) 3D printer. The 45° Lithoz group is the only sample group showing no significantly different results in trueness for all regions analysed compared to the milled group. Areal surface roughness analysis indicates that the print layers in the marginal regions are within clinically tolerable limits and surface characteristics. CONCLUSIONS: The printing orientation for zirconia crowns is critical to trueness, and differences are evident between different AM apparatuses. Considerations for design and orientation between different apparatuses should therefore be considered when utilising direct additive manufacturing processes. The areal surface roughness of the marginal regions is within acceptable clinical limits for all manufacturing processes and print orientations considered. CLINICAL SIGNIFICANCE: The materials and apparatuses for additive manufacturing of zirconia crowns are now clinically acceptable from the perspective of the trueness of a final crown for critical functional surfaces and areal surface roughness of the marginal regions.

Comparison of properties and cost efficiency of zirconia processed by DIW printing, casting and CAD/CAM-milling.

OBJECTIVES: The aim of this study was to evaluate the mechanical properties and cost efficiency of direct ink writing (DIW) printing of two different zirconia inks compared to casting and subtractive manufacturing. METHODS: Zirconia disks were manufactured by DIW printing and the casting process and divided into six subgroups (n = 20) according to sintering temperatures (1350 °C, 1450 °C and 1550 °C) and two different ink compositions (Ink 1, Ink 2). A CAD/CAM-milled high strength zirconia (3Y-TZP) was added as reference group. The biaxial flexural strength (BFS) was measured using the piston-on-three-balls test. X-ray-diffraction (XRD) was used for microstructural analysis. The cost efficiency was compared for DIW printing and subtractive manufacturing by calculation of the manufacturing costs of one dental crown. RESULTS: Using XRD, monoclinic and tetragonal phases were detected for Ink 1, for all other groups no monoclinic phase was detected. The CAD/CAM-milled ceramic showed a significantly higher BFS than all other groups. The BFS of Ink 2 was significantly higher than the BFS of Ink 1. At a sintering temperature of 1550 °C the mean BFS of the printed Ink 2 was 822 ± 174 MPa. The BFS of the cast materials did not show a significantly higher BFS than the corresponding printed group for any tested parameter-set. The manufacturing costs of DIW printed crowns are lower than the manufacturing costs of CAD/CAM-milled crowns. CONCLUSION: DIW has a high potential to replace subtractive processes for dental applications, as it shows promising mechanical properties for appropriate ink compositions and facilitates a highly cost effective production.

In Vitro Assessment of Retention and Resistance Failure Loads of Teeth Restored with a Complete Coverage Restoration and Different Core Materials.

PURPOSE: To investigate in vitro the retention and the resistance form, as well as the failure modes of maxillary premolars restored with cast metal crowns and different core materials. MATERIALS AND METHODS: Sixty human extracted maxillary premolars were selected according to their size and were embedded in PMMA resin blocks. After removing a part of their clinical crowns, the teeth were randomly divided into 3 groups of 20 teeth and were either left unrestored, or they were restored with amalgam or composite resin. All teeth were prepared for a cast metal complete coverage restoration. The restorations were cemented on the prepared teeth with a resin-modified glass ionomer luting agent (GC Fuji Plus). All specimens were subjected to static loading at 1 mm/min by a universal testing machine, until failure. Half the specimens of each group were subjected to tensile loading along the long axis of the teeth. The other half were subjected to compressive loading at a 30° angle. Failure loads and failure modes for each tooth were recorded. The statistical analysis included descriptive statistics, one-way ANOVA, and Tukey's HSD test. RESULTS: One-way ANOVA revealed statistically significant differences among the 3 tested groups (p < 0.05) for both tests. The group of teeth with no core material presented the highest failure loads for both the tensile and the compressive loading tests, with mean loads of 381.02 Ν and 741.21 Ν, respectively. Mean tensile and compressive failure loads for the amalgam group were 277.34 Ν and 584.75 Ν, while the composite resin group presented the lowest tensile and compressive failure values, which were 250.77 Ν and 465.78 Ν, respectively. The compression loading test resulted in the same failure mode for all specimens, which included unfavorable fracture of the teeth in combination with detachment of the cast metal complete coverage restorations. The tensile loading test resulted in different failure modes between the groups that used a core material and the group with no core material. CONCLUSIONS: Teeth that lost more than half of their coronal structure presented better retention and resistance form if no core material was used, provided that a minimum of 2-mm axial wall height was present at the missing part. Teeth that have lost more than half of their coronal structure and were restored with amalgam core presented better retention and resistance form than those restored with composite resin. Catastrophic fractures, extending to the root, were associated with compression forces but not with tensile forces.

Assessment of the trueness and tissue surface adaptation of CAD-CAM maxillary denture bases manufactured using digital light processing.

STATEMENT OF PROBLEM: Limited information is available evaluating the trueness and tissue surface adaptation of computer-aided design and computer-aided manufacturing (CAD-CAM) maxillary denture bases fabricated using digital light processing (DLP). PURPOSE: The purpose of this in vitro study was to evaluate the trueness of DLP-fabricated denture bases and to compare the tissue surface adaptation of DLP with milling (MIL) and pack and press (PAP). MATERIAL AND METHODS: The maxillary denture bases were virtually designed on the reference cast and were fabricated using DLP and MIL. Their intaglio surfaces were scanned and superimposed on the reference computer-aided design denture base to evaluate the trueness. A total of 20 denture bases (10 per technique) were also fabricated on the duplicated master casts using DLP and MIL. Ten denture bases were additionally made using PAP. The intaglio surfaces of the dentures were scanned and superimposed on the corresponding casts to compare the degree of tissue surface adaptation among the 3 techniques. The Mann-Whitney test and Kruskal-Wallis ANOVA were used for statistical analyses (α=.05). RESULTS: The trueness of the DLP denture base was significantly better than that of the MIL denture base (P<.001). Statistically significant differences were detected with respect to tissue surface adaptation of the denture base among the groups (P<.001). The DLP denture base showed the best denture base fit among the 3 techniques with a small interquartile range. CONCLUSIONS: Within the limitations of this in vitro study, the DLP maxillary denture base showed better trueness and tissue surface adaptation of ≤100 µm of the 3-dimensional surface deviation than the MIL and PAP denture bases.

Radiopacity and Chemical Assessment of New Commercial Calcium Silicate-Based Cements / Radiopacidad y Evaluación Química de Cementos Comerciales en Base a Silicato de Calcio

ABSTRACT: The aim of the study was to evaluate the chemical composition and radiopacity of new calcium-silicatebased cements. Discs of 10 mm x 1 ± 0.1mm were prepared of BiodentineTM, TheraCal, Dycal and GC Fuji IX (n=5). The samples were radiographed directly on an PSP occlusal plate adjacent to an aluminium step wedge. The radiopacity of each specimen was determined according to ISO 9917/2007. Statistical analyses were carried out using ANOVA and Tukey's test at a significance level of 5 %. The chemical constitution of materials was determined by scanning electron microscopy (SEM) and energy dispersive x-ray element mapping. The radiopacities of the materials in decreasing order were: GC Fuji IX (3.45 ± 0.16 mm), Dycal (3.18 ± 0.17), BiodentineTM (2.79 ± 0.22), and TheraCal (2.17 ± 0.17). TheraCal showed the lowest radiopacity compared to the other materials, followed by BiodentineTM. Dycal and GC Fuji IX radiopacity values did not present significant statistical differences. Scanning electron microscopy and energy dispersive X-ray analysis revealed the presence of zirconium in BiodentineTM; and strontium, barium and zirconium in TheraCal as radiopacifying elements. The new calcium silicate cements present distinctive chemical composition. BiodentineTM contains zirconium as a radiopacifying element and has higher radiopacity values than TheraCal, which contains barium and strontium as radiopacifiers.

RESUMEN: El objetivo de este estudio fue evaluar la composición química y la radiopacidad de nuevos cementos en base a silicato de calcio. Discos de 10 mm x 1 ± 0,1 mm fueron preparados con BiodentineTM, TheraCal, Dycal y GC Fuji IX (n=5). Las muestras fueron radiografiadas directamente en una película PSP oclusal adyacente a una cuña escalonada de aluminio. La radiopacidad de cada espécimen fue determinada de acuerdo a la norma ISO 9917/ 2007. Se realizaron los análisis estadísticos con las pruebas ANOVA y test de Tukey con un nivel de significancia de 5 %. La constitución química de los materiales fue determinada con microscopía electrónica de barrido y con mapeo por análisis con dispersión de energía de rayos X. La radiopacidad de los materiales en orden decreciente fue: GC Fuji IX (3,45 ± 0,16 mm), Dycal (3,18 ± 0,7 mm), BiodentineTM (2,79 ± 0,22 mm), y TheraCal (2,17 ± 0,17 mm). TheraCal mostró la menor radiopacidad comparada con los otros materiales, seguido de BiodentineTM. Los valores de radiopacidad de Dycal y GC Fuji IX no presentaron diferencias estadísticas significativas. Los análisis de microscopía electrónica de barrido y mapeo por análisis con dispersión de energía de rayos X revelaron la presencia de zirconio en BiodentineTM; y de estroncio, bario y zirconio en TheraCal, como elementos radiopacos. Los nuevos cementos en base a silicato de calcio presentan una composición química distintiva. BiodentineTM contienen zirconio como elemento que provee radiopacidad y tiene mayor valor de radiopacidad que TheraCal, el cual contiene bario y estroncio como agente radiopaco.

The effect of base material composition on demineralization assessment in CPOCT dental imaging.

Cross-polarization optical coherence tomography (CP-OCT) is a promising imaging modality to detect demineralization under the margins of composite restorations. The aim of this study was to assess how base materials applied under composite resin may affect CP-OCT image assessment. Base materials are commonly used for managing deep dentinal decay but once applied residual amounts of the base materials can be inadvertently left on the inner enamel walls. This study determined that base materials have significantly different scattering properties. The order grouping in the mean backscattered reflectivity (mR) of the base material was Dycal>caries phantom>Fuji IX, Vitrebond, Fuji II (p<0.05). The calcium hydroxide base (Dycal) had a higher mR than demineralized dentin and Vitrebond before and after the resin restoration was placed (p<0.05). While calcium hydroxide maybe a confounder in CPOCT imaging, several protective base materials are compatible with this type of imaging modality.

Micro-computed tomography assessment of root dentin around fluoride-releasing restorations after demineralization/remineralization.

Using micro-computed tomography (micro-CT), this study assessed the inhibitory effect of three different types of restorations on root-caries formation under a cariogenic challenge. Bovine-root dentin blocks with a cylindrical cavity were divided into three restoration groups: a fluoride-free self-etch adhesive and a resin composite (SE-ES); a self-etch adhesive and a resin composite with multi-ion release (FL-BF); and a glass ionomer cement (Fuji-VII). After the restorative procedures, the specimens were stored in artificial saliva for 1 d, then subjected to a demineralization solution for 4 d and a remineralization solution for 28 d. Mineral density and mean mineral loss of dentin around the restorations were measured using micro-CT. The mean mineral loss values of dentin around the restorations were highest among SE-ES restorations and lowest among Fuji-VII restorations. Fuji-VII showed the highest mineral density and the lowest mineral loss after 28 d of remineralization. The observations made by scanning electron microscopy demonstrated that Fuji-VII created the smallest outer lesion followed by FL-BF and SE-ES. Fuji-VII has a larger inhibitory effect on root caries around the restorations and enhances remineralization more effectively than either FL-BF or SE-ES. Multi-ion and fluoride release from the restorative materials may be beneficial for inhibition of root-dentin caries around the restorations.

Modal analysis for implant stability assessment: Sensitivity of this methodology for different implant designs.

OBJECTIVE: To investigate the influence of implant design on the change in the natural frequency of bone-implant system during osseointegration by means of a modal 3D finite element analysis. METHODS: Six implants were considered. Solid models were obtained by means of reverse engineering techniques. The mandibular bone geometry was built-up from a CT scan dataset through image segmentation. Each implant was virtually implanted in the mandibular bone. Two different models have been considered, differing in the free length of the mandibular branch ('long branch' and 'short branch') in order to simulate the variability of boundary conditions when performing vibrometric analyses. Modal analyses were carried out for each model, and the first three resonance frequencies were assessed with the respective vibration modes. RESULTS: With reference to the 'long branch' model, the first three modes of vibration are whole bone vibration with minimum displacement of the implant relative to bone, with the exception of the initial condition (1% bone maturation) where the implant is not osseointegrated. By contrast, implant displacements become relevant in the 'short branch' model, unless osseointegration level is beyond 20%. The difference between resonance frequency at whole bone maturation and resonance frequency at 1% bone maturation remained lower than 6.5% for all modes, with the exception of the third mode of vibration in the 'D' implant where this difference reached 9.7%. With reference to the 'short branch', considering the first mode of vibration, 61-68% of the frequency increase was achieved at 10% osseointegration; 72-79% was achieved at 20%; 89-93% was achieved at 50% osseointegration. The pattern of the natural frequency versus the osseointegration level is similar among different modes of vibration. SIGNIFICANCE: Resonance frequencies and their trends towards osseointegration level may differ between implant designs, and in different boundary conditions that are related to implant position inside the mandible; tapered implants are the most sensitive to bone maturation levels, small implants have very little sensitivity. Resonance frequencies are less sensitive to bone maturation level beyond 50%.

Assessment of cuspal deflection and volumetric shrinkage of different bulk fill composites using non-contact phase microscopy and micro-computed tomography.

The understanding of cuspal deflection and volumetric shrinkage of resin composites is necessary to assess and improve the placement techniques of resin-based materials. The aim of this study was to investigate the cuspal deflection and its relationship with volumetric polymerization shrinkage of different bulk-fill resin composites. The investigation was conducted using non-contact phase microscopy and micro-computed tomography. Thirty custom-milled aluminum blocks were fabricated for microscopy analysis and thirty-six tooth models with standardized Class I cavities were used for micro-computed tomography analysis. Results showed that high-viscosity composites present higher cuspal deflection compared to bulk-fill composites. The filler loading of resin composites seems to have an effect on cusp deflection, since the higher the filler content percentage, the higher the cusp deflection. On the other hand, it seems to have an opposite effect on volumetric shrinkage, since higher filler loadings produced lower volumetric shrinkage percentages.

Additive Technology: Update on Current Materials and Applications in Dentistry.

Additive manufacturing or 3D printing is becoming an alternative to subtractive manufacturing or milling in the area of computer-aided manufacturing. Research on material for use in additive manufacturing is ongoing, and a wide variety of materials are being used or developed for use in dentistry. Some materials, however, such as cobalt chromium, still lack sufficient research to allow definite conclusions about the suitability of their use in clinical dental practice. Despite this, due to the wide variety of machines that use additive manufacturing, there is much more flexibility in the build material and geometry when building structures compared with subtractive manufacturing. Overall additive manufacturing produces little material waste and is energy efficient when compared to subtractive manufacturing, due to passivity and the additive layering nature of the build process. Such features make the technique suitable to be used with fabricating structures out of hard to handle materials such as cobalt chromium. The main limitations of this technology include the appearance of steps due to layering of material and difficulty in fabricating certain material generally used in dentistry for use in 3D printing such as ceramics. The current pace of technological development, however, promises exciting possibilities.

Understanding dental CAD/CAM for restorations--dental milling machines from a mechanical engineering viewpoint. Part B: labside milling machines.

Nowadays, dental numerical controlled (NC) milling machines are available for dental laboratories (labside solution) and dental production centers. This article provides a mechanical engineering approach to NC milling machines to help dental technicians understand the involvement of technology in digital dentistry practice. The technical and economic criteria are described for four labside and two production center dental NC milling machines available on the market. The technical criteria are focused on the capacities of the embedded technologies of milling machines to mill prosthetic materials and various restoration shapes. The economic criteria are focused on investment cost and interoperability with third-party software. The clinical relevance of the technology is discussed through the accuracy and integrity of the restoration. It can be asserted that dental production center milling machines offer a wider range of materials and types of restoration shapes than labside solutions, while labside solutions offer a wider range than chairside solutions. The accuracy and integrity of restorations may be improved as a function of the embedded technologies provided. However, the more complex the technical solutions available, the more skilled the user must be. Investment cost and interoperability with third-party software increase according to the quality of the embedded technologies implemented. Each private dental practice may decide which fabrication option to use depending on the scope of the practice.

In vitro assessment of the biological response of Ti6Al4V implants coated with hydroxyapatite microdomains.

Dental implantology is still an expanding field of scientific study because of the number of people that receive dental therapies throughout their lives worldwide. Recovery times associated to dental surgery are still long and demand strategies to improve integration of metallic devices with hard tissues. In this work, an in vitro ceramic coating is proposed to improve and accelerate osseointegration of titanium surfaces conceived to be used as dental implants or hip or knee prosthesis, shaped either as dishes or screws. Such coating consists of hydroxyapatite microdomains on the implant surfaces obtained in vitro by immersion of titanium alloy samples (Ti6Al4V) in a simulated body fluid. This titanium alloy is highly used in implant dentistry and trauma surgery, among other fields. Once the immersion times under physiological conditions yielding to different ceramic topographies on this alloy were set, the acellular coating time of major interest so as to optimize its biological development was determined. For this purpose, dental pulp mesenchymal cells were cultured on titanium coated surfaces with different hydroxyapatite outline, and cell adhesion, proliferation and morphology were followed through histological techniques and scanning electron microscopy. It was found that 4 days of acellular hydroxyapatite coating led to a significant cell adhesion on the titanium alloys at an early stage (6 h). Cells tended although to detach from the surface of the coating over time, but those adhered on domains of intricated topography or hydroxyapatite cauliflowers proliferated on them, leading to isolated large cell clusters. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 2723-2729, 2016.

Understanding dental CAD/CAM for restorations - dental milling machines from a mechanical engineering viewpoint. Part A: chairside milling machines.

The dental milling machine is an important device in the dental CAD/CAM chain. Nowadays, dental numerical controlled (NC) milling machines are available for dental surgeries (chairside solution). This article provides a mechanical engineering approach to NC milling machines to help dentists understand the involvement of technology in digital dentistry practice. First, some technical concepts and definitions associated with NC milling machines are described from a mechanical engineering viewpoint. The technical and economic criteria of four chairside dental NC milling machines that are available on the market are then described. The technical criteria are focused on the capacities of the embedded technologies of these milling machines to mill both prosthetic materials and types of shape restorations. The economic criteria are focused on investment costs and interoperability with third-party software. The clinical relevance of the technology is assessed in terms of the accuracy and integrity of the restoration.

Diagnostic accuracy and measurement sensitivity of digital models for orthodontic purposes: A systematic review.

INTRODUCTION: Our objective was to assess the accuracy, validity, and reliability of measurements obtained from virtual dental study models compared with those obtained from plaster models. METHODS: PubMed, PubMed Central, National Library of Medicine Medline, Embase, Cochrane Central Register of Controlled Clinical trials, Web of Knowledge, Scopus, Google Scholar, and LILACs were searched from January 2000 to November 2014. A grading system described by the Swedish Council on Technology Assessment in Health Care and the Cochrane tool for risk of bias assessment were used to rate the methodologic quality of the articles. RESULTS: Thirty-five relevant articles were selected. The methodologic quality was high. No significant differences were observed for most of the studies in all the measured parameters, with the exception of the American Board of Orthodontics Objective Grading System. CONCLUSIONS: Digital models are as reliable as traditional plaster models, with high accuracy, reliability, and reproducibility. Landmark identification, rather than the measuring device or the software, appears to be the greatest limitation. Furthermore, with their advantages in terms of cost, time, and space required, digital models could be considered the new gold standard in current practice.

Grinding damage assessment on four high-strength ceramics.

OBJECTIVES: The purpose of this study was to assess surface and subsurface damage on 4 CAD-CAM high-strength ceramics after grinding with diamond disks of 75 µm, 54 µm and 18 µm and to estimate strength losses based on damage crack sizes. METHODS: The materials tested were: 3Y-TZP (Lava), dense Al2O3 (In-Ceram AL), alumina glass-infiltrated (In-Ceram ALUMINA) and alumina-zirconia glass-infiltrated (In-Ceram ZIRCONIA). Rectangular specimens with 2 mirror polished orthogonal sides were bonded pairwise together prior to degrading the top polished surface with diamond disks of either 75 µm, 54 µm or 18 µm. The induced chip damage was evaluated on the bonded interface using SEM for chip depth measurements. Fracture mechanics were used to estimate fracture stresses based on average and maximum chip depths considering these as critical flaws subjected to tension and to calculate possible losses in strength compared to manufacturer's data. RESULTS: 3Y-TZP was hardly affected by grinding chip damage viewed on the bonded interface. Average chip depths were of 12.7±5.2 µm when grinding with 75 µm diamond inducing an estimated loss of 12% in strength compared to manufacturer's reported flexural strength values of 1100 MPa. Dense alumina showed elongated chip cracks and was suffering damage of an average chip depth of 48.2±16.3 µm after 75 µm grinding, representing an estimated loss in strength of 49%. Grinding with 54 µm was creating chips of 32.2±9.1 µm in average, representing a loss in strength of 23%. Alumina glass-infiltrated ceramic was exposed to chipping after 75 µm (mean chip size=62.4±19.3 µm) and 54 µm grinding (mean chip size=42.8±16.6 µm), with respectively 38% and 25% estimated loss in strength. Alumina-zirconia glass-infiltrated ceramic was mainly affected by 75 µm grinding damage with a chip average size of 56.8±15.1 µm, representing an estimated loss in strength of 34%. All four ceramics were not exposed to critical chipping at 18 µm diamond grinding. CONCLUSIONS: Reshaping a ceramic framework post sintering should be avoided with final diamond grits of 75 µm as a general rule. For alumina and the glass-infiltrated alumina, using a 54 µm diamond still induces chip damage which may affect strength. Removal of such damage from a reshaped framework is mandatory by using sequentially finer diamonds prior to the application of veneering ceramics especially in critical areas such as margins, connectors and inner surfaces.

A register-based study of variations in services received among dental care attenders.

OBJECTIVES: To investigate whether receipt of dental services, among attenders, reflects variations in dental health or whether and to what degree it is associated with socioeconomic status, with irregular or regular dental attendance and with the availability of dentists in residential areas. MATERIALS AND METHODS: This retrospective register-based study followed two Danish cohorts, aged 25 and 40, with a dental examination in 2009 (n = 32,351). The dental service data were registered during 2005-2009. The number of dental examinations, individual preventive services (IPS), tooth extractions, root fillings and composite fillings were analyzed in relation to socioeconomic status, irregular/regular dental attendance, inhabitant/dentist ratio and to DMFT at age 15 (DMFT15) and change in DMFT (ΔDMFT) from age 15 to age 25 and age 40, respectively. Poisson regression and negative binomial regression analyses were used. RESULTS: The variations in number of services received in the study population were small (SD = 0.2-2.7). However, with a few exceptions, high levels of DMFT15 and ΔDMFT were associated with receipt of more dental services. Socioeconomically-privileged individuals received more dental examinations but fewer tooth extractions, root fillings and composite fillings compared to disadvantaged persons, when controlled for dental health levels. Irregular attenders received fewer IPS and composite fillings but had more extractions compared to regular attenders. CONCLUSIONS: Variations in dental care services were found to reflect variations in dental health, but the variations were also related to individual socioeconomic status, residential area and dental attendance patterns.

Technique Tips--The Cost of One Post-Operative Sensitivity following Placement of a Posterior Composite Restoration.

Use a low shrinkage stress composite but, if not, use incremental placement and a layer of flowable at the gingival box; Ensure good bonding to dentine and enamel and avoid (over) etching the dentine; Ensure good adaptation at the gingival floor of a Class II box; Make sure that the restoration has received sufficient light; Provide good isolation; Use reliable and tested materials throughout.