Assessment of spatially offset Raman spectroscopy to detect differences in bone matrix quality.

Since spatially offset Raman spectroscopy (SORS) can acquire biochemical measurements of tissue quality through light scattering materials, we investigated the feasibility of this technique to acquire Raman bands related to the fracture resistance of bone. Designed to maximize signals at different offsets, a SORS probe was used to acquire spectra from cadaveric bone with and without skin-like tissue phantoms attenuating the light. Autoclaving the lateral side of femur mid-shafts from 5 female and 5 male donors at 100 °C and again at 120 °C reduced the yield stress of cortical beams subjected to three-point bending. It did not affect the volumetric bone mineral density or porosity. Without tissue phantoms, autoclaving affected more Raman characteristics of the organic matrix when determined by peak intensity ratios, but fewer matrix properties depended on the three offsets (5 mm, 6 mm, and 7 mm) when determined by band area ratios. The cut-off in the thickness of the tissue phantom layers was ∼4 mm for most properties, irrespective of offset. Matching trends when spectra were acquired without phantom layers between bone and the probe, ν1PO43-/Amide III and ν1PO43-/(proline + OH-proline) were higher and lower in the non-treated bone than in the autoclaved bone, respectively, when the thickness of tissue phantom layers was 4 mm. The layers, however, caused a loss of sensitivity to autoclaving-related changes in ν3CO3/ν1PO43- and crystallinity. Without advanced post-processing of Raman spectra, SORS acquisition through turbid layers can detect changes in Raman properties of bone that accompany a loss in bone strength.

Assessment of glycosaminoglycan content in bone using Raman spectroscopy.

Glycosaminoglycans (GAGs) are responsible for preserving bone tissue toughness as well as regulating collagen formation and mineralization in the extracellular matrix. However, current methods for characterization of GAGs in bone are destructive, thus unable to capture in situ changes or differences in GAGs between experimental groups. As an alternative, Raman spectroscopy is a non-destructive method and can detect concurrent changes in GAGs and other bone constituents. In this study, we hypothesized that the two most prominent Raman peaks of sulfated GAGs (at ~1066 cm-1 and at ~1378 cm-1) could be used to detect differences in GAGs content of bone. To test this hypothesis, three experimental models were utilized: an in vitro model (enzymatic removal of GAGs from human cadaver bone), an ex vivo mouse model (biglycan KO vs. WT), and an ex vivo aging model (comparing cadaveric bone samples from young and old donors). All Raman measurements were compared to Alcian blue measurements to confirm the validity of Raman spectroscopy in detecting GAGs changes in bone. Irrespective of different models, it was found that the ~1378 cm-1 peak in Raman spectra of bone was uniquely sensitive to changes of GAGs content in bone when normalized with respect to the phosphate phase (~960 cm-1); i.e., 1378 cm-1/960 cm-1 (peak intensity ratio) or 1370-1385 cm-1/930-980 cm-1 (integrated peak area ratio). In contrast, the 1070 cm-1 peak, which includes another major peak of GAGs (1066 cm-1), seemed to be compromised to detect changes of GAGs in bone due to concurrent changes of carbonate (CO3) in the similar peak range. This study validates the ability of Raman spectroscopy to detect in situ treatment-, genotype-, and age-related changes in GAG levels of bone matrix.

Characterization of an advanced viable bone allograft with preserved native bone-forming cells.

Bone grafts are widely used to successfully restore structure and function to patients with a broad range of musculoskeletal ailments and bone defects. Autogenous bone grafts are historically preferred because they theoretically contain the three essential components of bone healing (ie, osteoconductivity, osteoinductivity, and osteogenicity), but they have inherent limitations. Allograft bone derived from deceased human donors is one alternative that is also capable of providing both an osteoconductive scaffold and osteoinductive potential but, until recently, lacked the osteogenic component of bone healing. Relatively new, cellular bone allografts (CBAs) were designed to address this need by preserving viable cells. Although most commercially-available CBAs feature mesenchymal stem cells (MSCs), osteogenic differentiation is time-consuming and complex. A more advanced graft, a viable bone allograft (VBA), was thus developed to preserve lineage-committed bone-forming cells, which may be more suitable than MSCs to promote bone fusion. The purpose of this paper was to present the results of preclinical research characterizing VBA. Through a comprehensive series of in vitro and in vivo assays, the present results demonstrate that VBA in its final form is capable of providing all three essential bone remodeling properties and contains viable lineage-committed bone-forming cells, which do not elicit an immune response. The results are discussed in the context of clinical evidence published to date that further supports VBA as a potential alternative to autograft without the associated drawbacks.

Comparative Assessment of Autogenous Cancellous Bone Graft and Bovine-Derived Demineralized Bone Matrix for Secondary Alveolar Bone Grafting in Patients With Unilateral Cleft Lip and Palate.

OBJECTIVE: Comparison between bovine-derived demineralized bone matrix (DMBM) and iliac crest graft over long term for secondary alveolar bone grafting (SABG) in patients with unilateral cleft lip and palate (UCLP) in terms of radiological and clinical outcomes. DESIGN: Prospective, randomized, parallel groups, double-blind, controlled trial. SETTING: Unit of Oral and Maxillofacial Surgery, Oral Health Science Centre, Postgraduate Institute of Medical Education & Research, Chandigarh. PARTICIPANTS: Twenty patients with UCLP. INTERVENTIONS: Patients were allocated into group I (Iliac crest bone graft) and group II (DMBM) for SABG. Outcomes were assessed at 2 weeks, 6 months, and then after mean follow-up period of 63 months. OUTCOMES MEASURES: Volumetric analysis of the grafted bone in the alveolar cleft site was done through cone beam computed tomography using Cavalieri principle and modified assessment tool. Clinical assessment was performed in terms of pain, swelling, duration of hospital stay, cost of surgery, alar base symmetry, and donor site morbidity associated with iliac crest harvesting. RESULTS: Volumetric analysis through Cavalieri principle revealed comparable bone uptake at follow-up of 6 months between group I (70%) and group II (69%). Modified assessment tool showed no significant difference between horizontal and vertical bone scores over short- and long-term follow-up. In group II, there was higher cost of surgery, but no donor site morbidity unlike group I. CONCLUSIONS: Demineralized bone matrix proved analogous to iliac crest bone graft as per volumetric analysis over shorter period. However, although statistically insignificant, net bone volume achieved was lower than the iliac crest graft at longer follow-up.

Osteoinductivity and biomechanical assessment of a 3D printed demineralized bone matrix-ceramic composite in a rat spine fusion model.

We recently developed a recombinant growth factor-free bone regenerative scaffold composed of stoichiometric hydroxyapatite (HA) ceramic particles and human demineralized bone matrix (DBM) particles (HA-DBM). Here, we performed the first pre-clinical comparative evaluation of HA-DBM relative to the industry standard and established positive control, recombinant human bone morphogenetic protein-2 (rhBMP-2), using a rat posterolateral spinal fusion model (PLF). Female Sprague-Dawley rats underwent bilateral L4-L5 PLF with implantation of the HA-DBM scaffold or rhBMP-2. Fusion was evaluated using radiography and blinded manual palpation, while biomechanical testing quantified the segmental flexion-extension range-of-motion (ROM) and stiffness of the fused segments at 8-weeks postoperatively. For mechanistic studies, pro-osteogenic gene and protein expression at 2-days and 1-, 2-, and 8-weeks postoperatively was assessed with another cohort. Unilateral fusion rates did not differ between the HA-DBM (93%) and rhBMP-2 (100%) groups; however, fusion scores were higher with rhBMP-2 (p = 0.008). Both treatments resulted in significantly reduced segmental ROM (p < 0.001) and greater stiffness (p = 0.009) when compared with non-operated controls; however, the degree of stabilization was significantly higher with rhBMP-2 treatment relative to the HA-DBM scaffold. In the mechanistic studies, PLGA and HA scaffolds were used as negative controls. Both rhBMP-2 and HA-DBM treatments resulted in significant elevations of several osteogenesis-associated genes, including Runx2, Osx, and Alp. The rhBMP-2 treatment led to significantly greater early, mid, and late osteogenic markers, which may be the mechanism in which early clinical complications are seen. The HA-DBM scaffold also induced osteogenic gene expression, but primarily at the 2-week postoperative timepoint. Overall, our findings show promise for this 3D-printed composite as a recombinant growth factor-free bone graft substitute for spinal fusion. STATEMENT OF SIGNIFICANCE: Despite current developments in bone graft technology, there remains a significant void in adequate materials for bone regeneration in clinical applications. Two of the most efficacious bone graft options are the gold-standard iliac crest bone graft and recombinant human-derived bone morphogenetic protein-2 (rhBMP-2), available commercially as Infuse™. Although efficacious, autologous graft is associated with donor-site morbidity, and Infuse™ has known side effects related to its substantial host inflammatory response, possibly associated with a immediate, robust osteoinductive response. Hence, there is a need for a bone graft substitute that provides adequate osteogenesis without associated adverse events. This study represents a significant step in the design of off-the-shelf growth factor-free devices for spine fusion.

Assessment of Osteocytes: Techniques for Studying Morphological and Molecular Changes Associated with Perilacunar/Canalicular Remodeling of the Bone Matrix.

Recent advances have revived interest in the concept of osteocyte perilacunar/canalicular remodeling (PLR) and have motivated efforts to identify the mechanisms regulating this process in bone in the context of normal physiology and pathological conditions. Here, we describe several methods that are evaluating morphological changes associated with PLR function of osteocytes.

In vitro and in vivo assessment of CaP materials for bone regenerative therapy. The role of multinucleated giant cells/osteoclasts in bone regeneration.

In this work, bone formation/remodeling/maturation was correlated with the presence of multinucleated giant cells (MGCs)/osteoclasts (tartrate-resistant acid phosphatase [TRAP]-positive cells) on the surface of beta-tricalcium phosphate (ß-TCP), sintered deproteinized bovine bone (sDBB), and carbonated deproteinized bovine bone (cDBB) using a maxillary sinus augmentation (MSA) in a New Zealand rabbit model. Microtomographic, histomorphometric, and immunolabeling for TRAP-cells analyses were made at 15, 30, and 60 days after surgery. In all treatments, a faster bone formation/remodeling/maturation and TRAP-positive cells activity occurred in the osteotomy region of the MSA than in the middle and submucosa regions. In the ß-TCP, the granules were rapidly reabsorbed by TRAP-positive cells and replaced by bone tissue. ß-TCP enabled quick bone regeneration/remodeling and full bone and marrow restoration until 60 days, but with a significant reduction in MSA volume. In cDBB and sDBB, the quantity of TRAP-positive cells was smaller than in ß-TCP, and these cells were associated with granule surface preparation for osteoblast-mediated bone formation. After 30 days, more than 80% of granule surfaces were surrounded and integrated by bone tissue without signs of degradation, preserving the MSA volume. Overall, the materials tested in a standardized preclinical model led to different bone formation/remodeling/maturation within the same repair process influenced by different microenvironments and MGCs/osteoclasts. © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 108B:282-297, 2020.

Xenogeneic bone matrix immune risk assessment using GGTA1 knockout mice.

Homeotransplantation of bones for replacement therapy have been demonstrated reliably in clinical data. However, human donor bones applicable for homeotransplantation are in short supply, which facilitates the search for suitable alternatives, such as xenografts grafts. The α-Gal antigen-related immune risk of xenografts directly affects the safety and effectiveness of the biomaterials and limits their applications in the clinic. The immune risk can be prevented by depletion or breaking anti-Gal antibody prior to transplant. Therefore, how to assess the immune risk of the bone substitutes and select the reliable animal research model become extremely important. In this study, we prepared lyophilized bone substitutes (T1) and Guanghao Biotech bone substitutes (T2, animal-derived biomaterials with α-Gal antigen decreased), aimed to assess the immune risk of xenografts bone substitutes on GGTA1 knockout mice. The α-Gal antigen contents of T1 and T2 were firstly detected by ELISA method in vitro. The bone substitutes were then implanted subcutaneously into GGTA1 knockout mice for 2, 4 and 12 weeks, respectively. The total serum antibody levels, anti-α-Gal antibody levels, inflammatory cytokine and splenic lymphocyte surface molecules were detected and histology analysis of skin and thymus were performed to systematically evaluate the immune response caused by the T1 and T2 bone substitutes in mice. In vitro results showed that the amount of α-Gal epitopes in T1 bone substitutes was significantly higher than T2 bone substitutes, and the clearance rate of α-Gal antigen in T2 bone substitutes achieved about 55.6%. Results of antibody level in vivo showed that the T1 bone substitutes group possessed significantly higher total IgG, IgM, IgA and anti-α-Gal IgG levels than T2 and control group, while T2 group showed no significant changes of these indexes compared with control. In terms of inflammatory cytokines, T1 bone substitutes showed evidently higher levels of IL-4, IL-12P70 and IL-10 than T2 and control, while T2 group was comparable to control. No changes in the levels of splenic lymphocyte surface molecules were found in the three groups (T1, T2 and control group) during the experimental periods. The pathological results demonstrated that the inflammatory response in T2 group was lighter than the T1 group, which was in accordance with the inflammatory cytokines levels. The above results indicated that the process of antigen removal effectively reduced the α-Gal antigens content in T2 bone substitutes, which caused little immune response in vivo and could be used as bone healing materials. This study also demonstrated that GGTA1 knockout mice can be used as a routine tool to assess the immune risk of animal-derived biomaterials.

Cost-Effectiveness Analysis of Demineralized Bone Matrix and rhBMP-2 versus Autologous Iliac Crest Bone Grafting in Alveolar Cleft Patients.

BACKGROUND: The standard of care for patients with alveolar cleft deformities is autologous bone grafting using iliac crest bone graft (ICBG). The combination of demineralized bone matrix with recombinant human bone morphogenetic protein-2 (DBX/rhBMP-2), as a substitute for ICGB, has been shown to have similar bony incorporation within the maxilla without donor-site morbidity. It has been argued that one of the drawbacks of using DBX/rhBMP-2 is the higher cost. The aim of this study was to compare the cost, operative time, and hospital length of stay associated with these two treatment modalities. METHODS: A chart review was conducted for 71 patients who underwent secondary alveolar cleft reconstruction. Forty patients received ICBG and 31 patients underwent reconstruction using DBX/rhBMP-2. Operative costs, operative time, and hospital length of stay were compared between the two groups. RESULTS: The average total operative cost was $6892 in the ICBG surgery population versus $4836 in the DBX/rhBMP-2 population (p < 0.01). Statistically significant decreases in anesthesia, pharmacy, and operating room costs were found in patients who underwent the DBX/rhBMP-2 surgery. Operative time decreased from an average of 97.3 minutes to 67.0 minutes (p < 0.01), and length of inpatient stay decreased from an average of 29.8 hours to 9.3 hours (p < 0.01). CONCLUSION: In the treatment of alveolar cleft deformities, operative material costs were greater in the DBX/rhBMP-2 group but-secondary to decreased hospital, anesthesia, pharmacy, and operating room costs-DBX/rhBMP-2 was more cost-effective than ICBG.

Budget impact analysis of demineralized bone matrix in combination with autograft in lumbar spinal fusion procedures for the treatment of lumbar degenerative disc disease in Spain.

OBJECTIVE: To estimate the budget impact (BI) of introducing local autograft (LA) combined with demineralized bone matrix (LA + DBM) in lumbar spinal fusion (LSF) procedures to treat lumbar degenerative disc disease (LDDD) in Spain. METHODS: A decision tree model was developed to evaluate the 4-year BI associated with introducing LA + DBM putty to replace currently available grafting methods, including iliac crest bone graft (ICBG), LA alone, and LA combined with beta-tricalcium phosphate (LA + ceramics), with 30%, 40%, and 30% market shares, respectively. The analysis was conducted for a hypothetical cohort of 100 patients with LDDD receiving LSF, assuming LA + DBM would replace 100% of the standard of care mix. The fusion rates extracted from the literature were validated by an expert panel. Costs (€2017) were obtained from different Spanish sources. Budget impact and incremental cost per successful fusion were calculated from the perspective of the Spanish National Health System (NHS). RESULTS: Over 4 years, replacing currently available options with LA + DBM for 100 patients resulted in an additional cost of €12,330 (€123/patient), and an additional 14 successful fusions, implying a cost of €881 per additional successful fusion. When costs of productivity loss were included, the introduction of LA + DBM resulted in cost savings of €70,294 (€703/patient). LIMITATIONS: The lack of high-quality, homogeneous, head-to-head research studying the efficacy of grafting procedures available to patients undergoing LSF, in addition to a lack of long-term follow-up in existing studies. Therefore, the number of fusions occurring within the model's time horizon may be underestimated. CONCLUSIONS: Acquisition costs of DBM were partially offset by costs of failed fusions, adverse events and reoperation when switching 100 hypothetical LDDD patients undergoing LSF procedures from standard of care grafting methods to LA + DBM from the perspective of the Spanish NHS. DBM cost was entirely offset when costs of lost productivity were considered.

Assessment of Bone Regeneration Using Adipose-Derived Stem Cells in Critical-Size Alveolar Ridge Defects: An Experimental Study in a Dog Model.

PURPOSE: To assess bone regeneration potential of a fibronectin- and adipose-derived stem cell-covered ceramic biomaterial in three-wall critical-size alveolar ridge defects. MATERIALS AND METHODS: In 18 dogs, four dehiscence-type and critical-size defects were created surgically in the edentulous alveolar ridge. Defects were randomly regenerated using biomaterials coated with particulate ß-tricalcium phosphate (ß-TCP), ß-TCP with fibronectin (Fn) (ß-TCP-Fn), and ß-TCP with a combination of Fn and autologous adipose-derived stem cells (ADSCs) (ß-TCP-Fn-ADSCs), leaving one defect as control. The animals were divided into three groups according to the time of euthanasia (1, 2, or 3 months of healing). RESULTS: At the time of sacrifice, statistically significant differences between the four types of defects in the total area of bone regeneration, percentage of neoformed bone matrix, medullary space, or contact between particulate biomaterial and neoformed bone matrix were not found. All defects showed a significant increase in neoformed bone matrix as sacrifice was delayed, but a uniform pattern was not followed. Only defects treated with ß-TCP-Fn-ADSCs showed a significant increase in the bone regeneration area when animals sacrificed at 3 months were compared to those sacrificed at 1 month (P = .006). CONCLUSION: The use of ADSCs in bone regeneration processes of critical-size defects of the alveolar ridge did not entail an advantage regarding greater bone regeneration as compared with other biomaterials. However, the use of ß-TCP coated with a combination of Fn and ADSCs appeared to favor stabilization of the regenerated area, allowing a more efficient maintenance of the space at 3 months of healing.

Bone matrix vesicle-bound alkaline phosphatase for the assessment of peripheral blood admixture to human bone marrow aspirates.

PURPOSE: Peripheral blood (PB) admixture should be minimized during numerical and functional, as well as cytokinetic analysis of bone marrow (BM) aspirates for research purposes. Therefore, purity assessment of the BM aspirate should be performed in advance. We investigated whether bone matrix vesicle (BMV)-bound bone alkaline phosphatase (ALP) could serve as a marker for the purity of BM aspirates. RESULTS: Total ALP activity was significantly higher in BM serum (97 (176-124)U/L, median (range)) compared to PB serum (63 (52-73)U/L, p < 0.001). Agarose gel electrophoresis showed a unique bone ALP fraction in BM, which was absent in PB. Native polyacrylamide gel electrophoresis revealed the high molecular weight of this fraction, corresponding with membrane-bound ALP from bone matrix vesicles (BMV), as evidenced by electron microscopy. A serial PB admixture experiment of bone cylinder supernatant samples, rich in BMV-bound ALP, confirmed the sensitivity of this proposed quality assessment method. Furthermore, a BMV ALP fraction of ≥ 15% is suggested as cut-off value for minimal BM quality. Moreover, the BM purity declines rapidly with larger aspirated BM volumes. CONCLUSION: The exclusive presence of BMV-bound ALP in BM could serve as a novel marker to assess purity of BM aspirates.

Assessment of bone healing in rabbit calvaria grafted with three different biomaterials.

This study evaluated the bone regeneration process in rabbit calvaria induced by three types of biomaterials: two xenogenous, consisting of deproteinized bovine bone, while the other was alloplastic, based on biphasic calcium phosphate. Five New Zealand white rabbits weighing between 2,900 and 3,500 g were submitted to four standard 8 mm-diameter perforations at the parietal bone. Three perforations were filled with three grafts and biomaterials, two of them received bovine Bio-Oss® and Endobon® Xenograft Granules, and the other consisted of fully alloplastic Straumann® Bone Ceramic. The fourth remaining cavity was used as control with coagulum. After eight weeks, the animals were sacrificed, and the samples were prepared for morphometric and qualitative analysis. The cavities filled with alloplastic biomaterials showed higher percentages of newly formed bone (p<0.05), while the cavities with xenogenous biomaterials showed higher amount of residual graft (p<0.05). Although the results showed greater bone formation with Straumann® Bone Ceramic, further studies are required to prove which is the more effective biomaterial for bone induction process.

A historical review of common bone graft materials in foot and ankle surgery.

Foot and ankle fusion is an important treatment for arthritis and deformities of the ankle and hindfoot. The literature has shown that there are improvements in fusion rates with the addition of bone graft and bone graft substitutes. Today autografts, specifically the iliac crest bone graft (ICBG), continue to be the gold standard despite significant donor site morbidity and nonunion rates, persisting around 10%. To address these drawbacks, bone graft substitutes have been developed. This article includes a historical review of the use, outcomes, and safety of autografts, allografts, and bone graft substitutes, such as ceramics, demineralized bone matrix, and platelet-derived growth factor.

[Harmonic imaging analysis for assessment of morphological changes in mini-pig alveolar bone by normal and increased functional load].

The aim of the study was to reveal the mastication forces effect on the microstructure of mandible bone tissue of mini-pigs by Fouirier harmonic imaging analysis of bone sections images of back scattered electrons and assessment of calcium and phosphorous distribution maps obtained by roentgenofluorescence technique. The results showed that by higher functional loads not only the total content of mineral elements in the bone matrix increased but also the of the low-frequency harmonics in the image spectrum indicating structural heterogeneity decrease in bone mineralization.

A histomorphometric comparison of Bio-Oss alone versus Bio-Oss and platelet-derived growth factor for sinus augmentation: a postsurgical assessment.

The purpose of this study was to assess vital bone formation at 4 to 5 months and 7 to 9 months following sinus augmentation with anorganic bovine bone matrix (ABBM) with and without recombinant human platelet-derived growth factor (rhPDGF). Twenty-four subjects received bilateral sinus elevation surgery with ABBM on one side and ABBM and rhPDGF on the contralateral side. Twelve patients had core sampling at 4 to 5 months and 12 patients at 7 to 9 months postoperatively. In subjects with cores taken at 4 to 5 months, mean vital bone, connective tissue, and residual graft were 11.8%, 54.1%, and 33.6%, respectively, with ABBM alone. Cores of sinuses filled with ABBM and rhPDGF showed mean 21.1% vital bone, 51.4% connective tissue, and 24.8% residual graft. Paired t test showed a statistically significant difference in vital bone. In cores taken at 7 to 9 months, the values for ABBM alone and ABBM + rhPDGF were 21.4% vs 19.5% vital bone, 28.4% vs 44.2% connective tissue, and 40.3% residual graft vs 35.5%. There was no statistically significant difference in vital bone at 7 to 9 months after surgery. Test and control groups showed clinically acceptable levels of vital bone both at 4 to 5 months and 7 to 9 months postsurgery. However, vital bone formation was significantly greater in the 4- to 5-month sections of ABBM + rhPDGF vs the Bio-Oss alone. In the 7- to 9-month specimens, this difference disappeared. More rapid formation of vital bone with the addition of rhPDGF may allow for earlier implant placement.

Quality assessment for processed and sterilized bone using Raman spectroscopy.

To eliminate the potential for infection, many tissue banks routinely process and terminally sterilize allografts prior to transplantation. A number of techniques, including the use of scanning electron microscopy, bone graft models, and mechanical property tests, are used to evaluate the properties of allograft bone. However, as these methods are time consuming and often destroy the bone sample, the quality assessment of allograft bones are not routinely performed after processing and sterilization procedures. Raman spectroscopy is a non-destructive, rapid analysis technique that requires only small sample volumes and has recently been used to evaluate the mineral content, mineral crystallinity, acid phosphate and carbonate contents, and collagen maturity in human and animal bones. Here, to establish a quality assessment method of allograft bones using Raman spectroscopy, the effect of several common sterilization and preservation procedures on rat femoral bones were investigated. We found that freeze-thawing had no detectable effects on the composition of bone minerals or matrix, although heat treatment and gamma irradiation resulted in altered Raman spectra. Our findings suggest Raman spectroscopy may facilitate the quality control of allograft bone after processing and sterilization procedures.