Safety assessment of charcoal usage and effects of common charcoal ignition aiders on combustion indices.

Charcoal is a popular form of biofuel embraced for domestic and industrial purposes. However, the use of Charcoal has some associated challenges, such as the required charcoal pot and setting it into the fire at first by using Charcoal-Ignition-Aiders (CIA) (e.g. discarded paper, nylon, rubber, plastics, petrol, the residue of processed palm oil, maise cob, wood, and kerosene). Coupled with the chemical properties of Charcoal, the resulting gases from CIA are capable of polluting the environment with perceived Adverse-Health-Implications (AHI) on the ecosystem. Therefore, this study conducted a safety assessment of charcoal biofuel usage and the effects of common CIA on combustion indices. This study followed standard methods and the use of peculiar equipment. This study established that Charcoal is commonly used in the studied area because it is cheap, readily available and requires less technical know-how. Considering the combustion indices, using paper as a CIA generated the lowest carbon monoxide (CO) value, 28.1 ppm, with 3,434.54 ppm volatile organic compound, VOC. Compared with the ACGIH standard permissible exposure level of ≤ 30 ppm, the paper gave a lesser CO value of 28.10 ppm among all the CIA. At the same time, all the CIA recorded higher VOC compared with EPA standard permissible exposure level of ≤ 15 ppm. ANOVA analysis conducted on the socio-demographic profile of the respondents, cooking attributes of the respondents, and use of charcoal pot types by the respondents in Zone 1, Zone 2, and Zone 3 gave p-values of 0.032, 0.028, and 0.039, respectively. These imply significant differences within the zones in each of the indices. The average energy content reported for charcoals sourced from oak trees, afara, obeche, mahogany, and iroko woods is 3,2149 kJ/kg compared to the lower ones. Therefore, this study recommended using these charcoals alongside discarded paper as CIA because they are a better combination to reduce AHI.

Non-targeted analysis and risk assessment of non-volatile compounds in polyamide food contact materials.

Small molecules in food contact materials may migrate into food during their contact. To extensively analyze the migrants, non-targeted screening is needed to detect the migrants. The migrants' detection is difficult because of the complexity and the trace amount of the migrants. In this work, the dissolution precipitation method was used to extract small molecules in Polyamide (PA) kitchenware. The extract solutions were screened by ultra-performance liquid chromatography-quadrupole time-of-flight-mass spectrometry (UPLC-QTOF-MS) for non-targeted analysis and 64 different small molecules in materials were identified through the screening of a self-built database. Then, migration tests were performed to analyze migrants in food simulants. It suggests that the abundance of PA oligomers was the highest in migrants. The risk assessment of migrants revealed that the exposure of most migrants was at a safer level unlike the exposure of PA oligomers that exceeded their threshold of toxicological concern (TTC).

Assessment of bullet holes through the analysis of mushroom-shaped morphology in synthetic fibres: analysis of six cases.

Textiles damage analysis is a very valuable tool in forensic investigations. However, to date, very little research has been carried out to understand the impact of bullet causing damages to clothing. According to the review of the most recent scientific papers, the frictional heating and crushing action of a bullet passing through synthetic fibres cause a unique transformation in their ends called mushroom-shaped morphology. In this study, the textile remains of six individuals executed during the first decade of the Chilean military dictatorship period (1973-1990) were analysed. The purpose was to examine their clothing in order to describe the fibre defects in the bullet holes. The fibres were directly observed using two different models of stereomicroscopy (MZ16A and EZ4D, Leica Microsystem Ltd., Wetzlar, Germany) and through a combination of transmitted, oblique and co-axial illumination (with Leica DFC500 Digital Camera), at × 230 and at a resolution of up to 840 Lp/mm. The mushroom-shaped morphology, along with rupturing of yarns, fibrillation or splitting of fibres, was observed in the bullet holes. Although the mushroom-shaped is a useful pattern for bullet hole identification in synthetic fibres, further research needs to be performed for developing a sounder interpretational framework of this type of forensic evidence.

Assessment of microplastic pollution: occurrence and characterisation in Vesijärvi lake and Pikku Vesijärvi pond, Finland.

In the last few years, several studies have investigated microplastics (MPs) in marine ecosystems, but data monitoring and assessing the occurrence in freshwater environments are still scarce. The present study aims to investigate the occurrence, distribution, and chemical composition of MP pollution in Vesijärvi lake and Pikku Vesijärvi pond close to the city of Lahti (Finland) in winter. Sediment, snow, and ice core samples were collected near the shore of these two aquatic systems. MPs were analysed and identified by a non-destructive method using Fourier transform infrared spectroscopy (FTIR) 2D imaging. The mean concentrations of MPs detected in sediment, snow, and ice samples were 395.5 ± 90.7 MPs/kg, 117.1 ± 18.4 MPs/L, and 7.8 ± 1.2 MPs/L, respectively. FTIR results showed the predominant abundance of microplastics, such as polyamides (up to 53.3%), polyethylene and polypropylene (up to 17.1%), and natural fragments such as cellulose (up to 45.8%) and wool (up 18.8%) in the same size range. The potential release of MPs arising from stormwaters and sport and recreational activities was evidenced.

Brush head composition, wear profile, and cleaning efficacy: an assessment of three electric brush heads using in vitro methods.

OBJECTIVE: The objective of this research was to evaluate a current store brand (SB) brush head for composition/physical characteristics, Wear Index (WI), and cleaning efficacy versus the previous SB brush head refill design (SB control) and the Oral-B Precision Clean brush head (positive control, PC). METHODS: This research consisted of three parts: 1) Analytical analysis using Fourier Transform Infrared (FT-IR) spectrometry to evaluate the chemical composition of the current SB brush head bristles relative to the SB control. In addition, physical parameters such as bristle count and diameter were determined. 2) Wear Index (WI) investigation to determine the Wear Index scores of in vitro-aged brush heads at four weeks (one month) and 13 weeks (three months) by a trained investigator. To "age" the brush heads, a robot system was used as a new alternative in vitro method to simulate aging by consumer use. 3) Robot testing to determine the cleaning performance of in vitro-aged brush heads, comparing one month-aged current SB brush heads with the SB control (one and three months-aged) and the PC brush heads (three months-aged) in a standardized fashion. RESULTS: 1) FT-IR analysis revealed that the chemical composition of the current and control SB refill brush heads is identical. In terms of physical parameters, the current SB brush head has 12% more bristles and a slightly oval brush head compared to the round brush head of the SB control. 2) Wear Index analysis showed there was no difference in the one month-aged current SB brush head versus the one month-aged SB control (1.67 vs. 1.50, p = 0.65) or versus the three months-aged PC brush head (1.67 vs. 1.50, p = 0.65). The one month-aged current SB brush head demonstrated statistically significantly less wear than the three months-aged SB control (1.67 vs. 2.67, p = 0.01). 3) Analysis of cleaning efficacy shows that the one month-aged current SB brush head had improved cleaning performance over the one month-aged SB control brush head (p < 0.05), despite no statistically significant difference in wear. Both the one month-aged current and control SB brush heads showed statistically significantly lower cleaning performance compared to the three months-aged PC brush heads (p < 0.01). CONCLUSION: While the current SB brush head showed improved cleaning over the SB control, it demonstrated significantly lower durability and cleaning in comparison to the PC brush head. Dental professionals should be aware of these differences, both in durability and in cleaning performance, when recommending brush heads to their patients.

[Methodical aspects of hygienic safety assessment of polymeric materials in contact with foodstuffs].

It was purposed new technique by capillary gas chromatography (GC) for the low level determination of monomer hexamethylenediamine (HMDA) in food simulants water from polymeric materials in contact with foodstuffs. Hexamethylenediamine, HN2-(CH2)6-NH2, is a monomer used in the manufacture of certain of polyamide plastic materials and articles intended to come into contact with foodstuffs. Compound exhibits all the chemical properties of aliphatic amines, is an irritant, causing dermatitis, can accumulate in the body, the degree of human exposure to HMDA assigned to the 2nd class of hazard - the substance is highly dangerous. There was studied two methodological approaches pre-derivatization of compound for GC determination. The first approach involves conversion of the free diamine using ethyl chloroformate as derivatizing agent followed by analysis of the resulting diurethan by gas chromatography using a flame ionization and mass selective detection (HMDA was quantitated by selective ion monitoring at m/z 102, the lower detection limit of 1 ng). According to second methodological approach the water samples were mixed with sodium chloride and extracted with toluene, then derivatized with trifluoroacetic anhydride (60 min, 55 degrees C) to diamide, 1 M potassium phosphate buffer (pH 7,0) was add to remove excess derivatizing agent, followed by analysis of resulting diamide by gas chromatography with electron capture detection (lower limit value 0,01 ng). Conformation of HMDA levels is carried out by combined gas chromatography/mass spectrometry (HMDA was quantitated by selective ion monitoring at m/z 126, the lower limit value of 0,1 ng). The optimal pre-derivatization of the second approach for the determination of low levels of HMDA in the water extracts. The range of measured concentrations of 0,005-0,5 mg/dm3, recovery 88-101%, the total error of measurement is 16%, the relative standard deviation is 1,85%. The method was tested in the study of aqueous extracts of the 10 random samples intended for food purchased in the consumer market. Shows the corresponding output level hexamethylenediamine requirements for products of this type.

Non-targeted multi-component analytical surveillance of plastic food contact materials: Identification of substances not included in EU positive lists and their risk assessment.

A procedure used by the Norwegian Food Safety Authority for surveillance of contaminants from plastic food contact materials (polyolefin drinking bottles, water boilers, polyamide cooking utensils and plastic multi-layer materials) is described. It is based on gas chromatographic-mass spectrometric (GC/MS) analysis of food simulants exposed to plastic materials. Most migrants were substances not-intentionally added to the plastic (degradation products, impurities) or originated from non-plastic components, such as printing inks, adhesives, not-listed additives, solvents and coatings. Hence, the majority of the identified migrants were regulated by the general statements in the EU Framework Regulation, which neither specify limits nor requirements regarding risk assessment, rather than by specific migration controls. Risk assessment has been carried out for selected non-authorized substances. The analysis and the management of these substances and materials with respect to safety represents a challenge to the food authorities.

Nylon de pescar como sutura quirúrgica: una alternativa en los servicios de salud / Fishing nylon as surgical suture: a choice in health services

Con el fin de comprobar la eficacia y eficiencia del nylon de pescar como sutura qurúrgica, estudiamos prospectivamente 254 pacientes en quienes se utilizó dicho material para el cierre de la pared abdominal, entre Setiembre de 1992 a Junio 1994 en el Hospital de Florencia de Mora del IPSS, Gerencia La Libertad. Los porcentajes de infección de herida encontrados fueron de 1.2 por ciento para heridas limpias y 1.2 por ciento para heridas contaminadas, cifras concordantes con la literatura consultada. En un seguimiento promedio de un año, encontramos que 5 pacientes (1.9 por ciento), prestaron "rechazo" al material, identificándose en 2 de ellos técnica quirúrgica deficiente; y 7 por ciento tuvieron algún grado de defecto estético (queloides, hiperpigmentadas). No hubieron evisceraciones ni, eventraciones. Constatamos una importante reducción de costos respecto al uso de suturas tradicionales de hasta 2000 por ciento. Por lo antes expuesto, planteamos el uso del nylon de pescar como sutura quirúrgica como una alternativa recomendable.