Use of sustainable packaging materials for fresh beef vacuum packaging application and product assessment using physicochemical means.

Packaging material should guarantee the longest possible shelf life of food and help to maintain its quality. The aim of the study was to assess the physicochemical changes taking place during 28-day ageing of beef steaks packed in two types of multilayer films containing biodegradable polymers - polylactic acid (NAT/PLA) and Mater-Bi® (NAT/MBI). The control group consisted of steaks packed in synthetic polyamide/polyethylene (PA/PE) film. The samples stored in NAT/PLA had significantly lower purge loss than the control samples and the lowest expressible water amount after 14 and 21 days. Following blooming, the most favourable colour was shown in steaks stored in NAT/MBI, with the highest values for the L*, a* and C* parameters and the R630/580 ratio, a high proportion of oxymyoglobin, and the lowest share of metmyoglobin. All steaks, regardless of the type of packaging material, had acceptable tenderness and were stable in terms of lipid oxidation.

Bioplastic derived from corn stover: Life cycle assessment and artificial intelligence-based analysis of uncertainty and variability.

Exploring feasible and renewable alternatives to reduce dependency on traditional fossil-based plastics is critical for sustainable development. These alternatives can be produced from biomass, which may have large uncertainties and variabilities in the feedstock composition and system parameters. This study develops a modeling framework that integrates cradle-to-grave life cycle assessment (LCA) with a rigorous process model and artificial intelligence (AI) models to conduct uncertainty and variability analyses, which are highly time-consuming to conduct using only the process model. This modeling framework examines polylactic acid (PLA) produced from corn stover in the U.S. An analysis of uncertainty and variability was conducted by performing a Monte Carlo simulation to show the detailed result distributions. Our Monte Carlo simulation results show that the mean life-cycle Global Warming Potential (GWP) of 1 kg PLA is 4.3 kgCO2eq (P5-P95 4.1-4.4) for composting PLA with natural gas combusted for the biorefinery, 3.7 kgCO2eq (P5-P95 3.4-3.9) for incinerating PLA for electricity with natural gas combusted for the biorefinery, and 1.9 kgCO2eq (P5-P95 1.6-2.1) for incinerating PLA for electricity with wood pellets combusted for the biorefinery. Tradeoffs for different environmental impact categories were identified. Based on feedstock composition variations, two AI models were trained: random forest and artificial neural networks. Both AI models demonstrated high prediction accuracy; however, the random forest performed slightly better.

Characterization, hazard identification, and risk assessment of volatile organic compounds in Poly(butylene adipate-co-terephthalate)-based food contact articles.

The chemical safety of poly (butylene adipate-co-terephthalate) (PBAT) based food contact articles (FCAs) has aroused increasing toxicological concerns in recent years, but the chemical characterization and associated risk assessment still remain inadequate as it fails to elucidate the distribution pattern and discern the potential genotoxic and carcinogenic hazards of the identified substances. Herein, the volatile organic compounds (VOCs) in 50 batches of PBAT-based FCAs of representative categories and 10 batches of PLA and PBAT pellets were characterized, by which 237 VOCs of 10 chemical categories were identified and exhibited characteristic distribution patterns in the chemical spaces derived from their molecular descriptors. Chemical hazards associated with the identified VOCs were discerned by a hazard-driven classification scheme integrating hazard-related knowledge from multiple publicly available sources, and 34 VOCs were found to bear genotoxic or carcinogenic hazards and to feature higher average molecular weight than the other VOCs. Finally, the Risk and hazard quotient (HQ) calculated as the metrics of risk suggested that all identified VOCs posed acceptable risks (Risk<10-4 or HQ < 1), whereas oxolane, butyrolactone, N,N-dimethylacetamide, 2-butoxyethanol, benzyl alcohol, and 1,2,3-trichloropropane posed non-negligible (Risk>10-6) genotoxic or carcinogenic risk and thus should be of prioritized concern to promote the chemical safety of PBAT-based FCAs.

The biological and therapeutic assessment of a P(3HB-co-4HB)-bioactive glass-graphene composite biomaterial for tissue regeneration.

An ideal wound dressing should create a healing environment that relieves pain, protects against infections, maintains moisture, removes debris, and speeds up wound closure and repair. However, conventional options like gauze often fall short in fulfilling these requirements, especially for chronic or nonhealing wounds. Hence there is a critical need for inventive formulations that offer efficient, cost-effective, and eco-friendly alternatives. This study focuses on assessing the innovative formulation based on a microbial-derived copolymer known as poly(3-hydroxybutyrate-co-4-hydroxybutyrate), P(3HB-co-4HB) bioactive glass and graphene particles, and exploring their biological response in vitro and in vivo-to find the best combination that promotes cell adhesion and enhances wound healing. The formulation optimized at concentration of bioactive glass (1 w/w%) and graphene (0.01 w/w%) showed accelerated degradation and enhanced blood vessel formation. Meanwhile biocompatibility was evaluated using murine osteoblasts, human dermal fibroblasts, and standard cell culture assays, demonstrating no adverse effects after 7 days of culture and well-regulated inflammatory kinetics. Whole thickness skin defect using mice indicated the feasibility of the biocomposites for a faster wound closure and reduced inflammation. Overall, this biocomposite appears promising as an ideal wound dressing material and positively influencing wound healing rates.

Development and physiochemical assessment of graphene-bioactive glass-P(3HB-co-4HB) composite scaffold as prospect biomaterial for wound healing.

The clinical management of wounds presents a considerable challenge because dressing selection must prioritise the provision of appropriate barrier and the healing properties, consider patient's compliance factors such as comfort, functionality and practicality. This study primarily aimed to develop a composite scaffold patch for potential application in wound healing. Poly(3-hydroxybutyrate-co-4-hydroxybutyrate) [P(3HB-co-4HB)] is a biopolymer that originated from bacteria. It is well-recognised owing to its distinctive mechanical and physical characteristics suitable for biomedical applications. Graphene (G) and bioactive glass (BG) are biocompatible towards humans, and enhanced properties are achievable by adding biopolymer. In this study, composite scaffolds were developed by combining P(3HB-co-4HB) at a distinct proportion of 4HB monomer reinforced with G (3.0 wt.%) and BG (2.5 wt.%) by using solvent casting, resulting in two types of composite scaffolds: P(3HB-co-25%4HB)/G/BG and P(3HB-co-37%4HB)/G/BG. A successful composite scaffold as a unified structure was achieved based on chemical assessments of organic and inorganic elements within the composites. The pure polymer displayed a smooth surface, and the BG and G addition into the composite scaffolds increased surface roughness, forming irregular pores and protuberances. The wettability and hydrophilicity of the composites significantly improved up to 40% in terms of water uptake. An increment in crystallisation temperature diminished the flexibility of the composite's scaffolds. Evaluation of Presto Blue biocompatibility demonstrated nontoxic behaviour with a dosage of less than 25.00 mg ml-1of composite scaffold-conditioned media. The L929 fibroblast cells displayed excellent adhesion to both types of composite scaffolds, as evidenced by the increased percentage of cell viability observed throughout 14 d of exposure. These findings demonstrate the importance of optimising each component within the composite scaffolds and their interrelation, paving the way for excellent material properties and enhancing the potential for wound healing applications.

Multi-level toxicity assessment of polylactic acid (PLA) microplastics on the cladoceran Daphnia magna.

The accumulation of plastics waste in the environment has raised a worrisome concern, moving the society to seek out for sustainable solutions, such as the transition from the use of fossil-based, conventional plastics to bioplastics (BPs). However, once in the environment bioplastics have the same probability to accumulate and experience weathering processes than conventional plastics, leading to the formation of microplastics (MPs). However, to date the information on the potential toxicity of MPs originated from the weathering of bioplastics is limited. Thus, this study aimed at investigating the adverse effects induced by the exposure to MPs made of a bioplastic polymer, the polylactic acid (PLA), towards the freshwater cladoceran Daphnia magna. Organisms were exposed for 21 days to three concentrations (0.125 µg/mL, 1.25 µg/mL and 12.5 µg/mL) of PLA microplastics (hereafter PLA-MPs). A multi-level approach was performed to investigate the potential effects through the biological hierarchy, starting from the sub-individual up to the individual level. At the sub-individual level, changes in the oxidative status (i.e., the amount of reactive oxygen species and the activity of antioxidant and detoxifying enzymes) and oxidative damage (i.e., lipid peroxidation) were explored. Moreover, the total caloric content as well as the content of protein, carbohydrate and lipid content assess were used to investigate the effects on energy reserves. At individual level the changes in swimming activity (i.e., distance moved and swimming speed) were assessed. Our results showed that the exposure to PLA-MPs induced a slight modulation in the oxidative status and energy reserves, leading to an increase in swimming behavior of treated individuals compared to control conspecifics. These results suggest that the exposure to MPs made of a bioplastic polymer can induce adverse effects similar to those caused by conventional polymers.

Benefits of Rib Fixation Utilizing Low-Cost Materials: A Randomized Pilot Trial.

INTRODUCTION: Surgical stabilization of rib fractures (SSRF) using standard rib plating systems has become a norm in developed countries. However, the procedure has not garnered much interest in low-middle-income countries, primarily because of the cost. METHODS: This was a single-center pilot randomized trial. Patients with severe rib fractures were randomized into two groups: SSRF and nonoperative management. SSRF arm patients underwent surgical fixation in addition to the tenets of nonoperative management. Low-cost materials like stainless steel wires and braided polyester sutures were used for fracture fixation. The primary outcome was to assess the duration of hospital stay. RESULTS: Twenty-two patients were randomized, 11 in each arm. Per-protocol analysis showed that the SSRF arm had significantly reduced duration of hospital stay (22.6 ± 19.1 d versus 7.9 ± 5.7 d, P value 0.031), serial pain scores at 48 h and 5 d (median score 5, IQR (3-6) versus median score 7, IQR (6.5-8), P value 0.004 at 48 h and median score 2 IQR (2-3) versus median score 7 IQR (4.5-7) P value 0.0005 at 5 d), significantly reduced need for injectable opioids (9.9 ± 3.8 mg versus 4.4 ± 3.4 mg, P value 0.003) and significantly more ventilator-free days (19.9 ± 8.7 d versus 26.4 ± 3.2 d, P value 0.04). There were no statistically significant differences in the total duration of ICU stay (median number of days 2, IQR 1-4.5 versus median number of days 7, IQR 1-14, P value 0.958), need for tracheostomy (36.4% versus 0%, P value 0.155), and pulmonary and pleural complications. CONCLUSIONS: SSRF with low-cost materials may provide benefits similar to standard rib plating systems and can be used safely in resource-poor settings.

Design, clinical applications and post-surgical assessment of bioresorbable 3D-printed craniofacial composite implants.

This study details the design, fabrication, clinical trials' evaluation, and analysis after the clinical application of 3D-printed bone reconstruction implants made of nHAp@PLDLLA [nanohydroxyapatite@poly(L-lactide-co-D,L-lactide)] biomaterial. The 3D-printed formulations have been tested as bone reconstruction Cranioimplants in 3 different medical cases, including frontal lobe, mandibular bone, and cleft palate reconstructions. Replacing one of the implants after 6 months provided a unique opportunity to evaluate the post-surgical implant obtained from a human patient. This allowed us to quantify physicochemical changes and develop a spatial map of osseointegration and material degradation kinetics as a function of specific locations. To the best of our knowledge, hydrolytic degradation and variability in the physicochemical and mechanical properties of the biomimetic, 3D-printed implants have not been quantified in the literature after permanent placement in the human body. Such analysis has revealed the constantly changing properties of the implant, which should be considered to optimize the design of patient-specific bone substitutes. Moreover, it has been proven that the obtained composition can produce biomimetic, bioresorbable and bone-forming alloplastic substitutes tailored to each patient, allowing for shorter surgery times and faster patient recovery than currently available methods.

Techno-economic assessment of biopolymer production from methane and volatile fatty acids: effect of the reactor size and biomass concentration on the poly(3-hydroxybutyrate-co-3-hydroxyvalerate) selling price.

Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) is a biobased and biodegradable polymer that could efficiently replace fossil-based plastics. However, its widespread deployment is slowed down by the high production cost. In this work, the techno-economic assessment of the process for producing poly(3-hydroxybutyrate-co-3-hydroxyvalerate) from low-cost substrates, such as methane and valeric acid derived from the anaerobic digestion of organic wastes, is proposed. Several strategies for cost abatement, such as the use of a mixed consortium and a line for reagent recycling during downstream, were adopted. Different scenarios in terms of production, from 100 to 100,000 t/y, were analysed, and, for each case, the effect of the reactor volume (small, medium and large size) on the selling price was assessed. In addition, the effect of biomass concentration was also considered. Results show that the selling price of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) is minimum for a production plant with 100,000 t/y capacity, accounting for 18.4 €/kg, and highly influenced by the biomass concentration since it can be reduced up to 8.6 €/kg by increasing the total suspended solids from 5 to 30 g/L, This adjustment aligns the breakeven point of PHBV with the reported average commercial price.

Environmental sustainability assessment of biodegradable bio-based poly(3-hydroxybutyrate-co-3-hydroxyvalerate) from agro-residues: Production and end-of-life scenarios.

In the context of a circular bio-based economy, more public attention has been paid to the environmental sustainability of biodegradable bio-based plastics, particularly plastics produced using emerging biotechnologies, e.g. poly(3-hydroxybutyrate-co-3-hydroxyvalerate) or PHBV. However, this has not been thoroughly investigated in the literature. Therefore, this study aimed to address three aspects regarding the environmental impact of PHBV-based plastic: (i) the potential environmental benefits of scaling up pellet production from pilot to industrial scale and the environmental hotspots at each scale, (ii) the most favourable end-of-life (EOL) scenario for PHBV, and (iii) the environmental performance of PHBV compared to benchmark materials considering both the pellet production and EOL stages. Life cycle assessment (LCA) was implemented using Cumulative Exergy Extraction from the Natural Environment (CEENE) and Environmental Footprint (EF) methods. The results show that, firstly, when upscaling the PHBV pellet production from pilot to industrial scale, a significant environmental benefit can be achieved by reducing electricity and nutrient usage, together with the implementation of better practices such as recycling effluent for diluting feedstock. Moreover, from the circularity perspective, mechanical recycling might be the most favourable EOL scenario for short-life PHBV-based products, using the carbon neutrality approach, as the material remains recycled and hence environmental credits are achieved by substituting recyclates for virgin raw materials. Lastly, PHBV can be environmentally beneficial equal to or even to some extent greater than common bio- and fossil-based plastics produced with well-established technologies. Besides methodological choices, feedstock source and technology specifications (e.g. pure or mixed microbial cultures) were also identified as significant factors contributing to the variations in LCA of (bio)plastics; therefore, transparency in reporting these factors, along with consistency in implementing the methodologies, is crucial for conducting a meaningful comparative LCA.

Effect of bolus materials on dose deposition in deep tissues during electron beam radiotherapy.

Several materials are utilized in the production of bolus, which is essential for superficial tumor radiotherapy. This research aimed to compare the variations in dose deposition in deep tissues during electron beam radiotherapy when employing different bolus materials. Specifically, the study developed general superficial tumor models (S-T models) and postoperative breast cancer models (P-B models). Each model comprised a bolus made of water, polylactic acid (PLA), polystyrene, silica-gel or glycerol. Geant4 was employed to simulate the transportation of electron beams within the studied models, enabling the acquisition of dose distributions along the central axis of the field. A comparison was conducted to assess the dose distributions in deep tissues. In regions where the percentage depth dose (PDD) decreases rapidly, the relative doses (RDs) in the S-T models with silica-gel bolus exhibited the highest values. Subsequently, RDs for PLA, glycerol and polystyrene boluses followed in descending order. Notably, the RDs for glycerol and polystyrene boluses were consistently below 1. Within the P-B models, RDs for all four bolus materials are consistently below 1. Among them, the smallest RDs are observed with the glycerol bolus, followed by silica-gel, PLA and polystyrene bolus in ascending order. As PDDs are ~1-3% or smaller, the differences in RDs diminish rapidly until are only around 10%. For the S-T and P-B models, polystyrene and glycerol are the most suitable bolus materials, respectively. The choice of appropriate bolus materials, tailored to the specific treatment scenario, holds significant importance in safeguarding deep tissues during radiotherapy.

Optimization of Electrospun Bilayer Vascular Grafts through Assessment of the Mechanical Properties of Monolayers.

Small-diameter vascular grafts must be obtained with the most appropriate materials and design selection to harmoniously display a variety of features, including adequate tensile strength, compliance, burst strength, biocompatibility, and biodegradability against challenging physiological and hemodynamic conditions. In this study, monolayer vascular grafts with randomly distributed or radially oriented fibers are produced using neat, blended, and copolymer forms of polycaprolactone (PCL) and poly(lactic acid) (PLA) via the electrospinning technique. The blending ratio is varied by increasing 10 in the range of 50-100%. Bilayer graft designs are realized by determining the layers with a random fiber distribution for the inner layer and radial fiber orientation for the outer layer. SEM analysis, wall thickness and fiber diameter measurements, tensile strength, elongation, burst strength, and compliance tests are done for both mono- and bilayer scaffolds. The findings revealed that the scaffolds made of neat PCL show more flexibility than the neat PLA samples, which possess higher tensile strength values than neat PCL scaffolds. Also, in blended samples, the tensile strength values do not show a significant improvement, whereas the elongation values are enhanced in tubular samples, depending on the blending ratio. Also, neat poly(l-lactide-co-caprolactone) (PLCL) samples have both higher elongation and strength values than neat and blended scaffolds, with some exceptions. The blended specimens comprising a combination of PCL and PLA, with blending ratios of 80/20 and 70/30, exhibited the most elevated burst pressures. Conversely, the PLCL scaffolds demonstrated superior compliance levels. These findings suggest that the blending approach and fiber orientation offer enhanced burst strength, while copolymer utilization in PLCL scaffolds without fiber alignment enhances their compliance properties. Thus, it is evident that using a copolymer instead of blending PCL and PLA and combining the PLCL layer with PCL and PLA monolayers in bilayer vascular graft design is promising in terms of mechanical and biological properties.

Identification of non-volatile non-intentionally added substances from polyester food contact coatings and genotoxicity assessment of polyester coating's migrates.

Can's polyester coatings are intended to replace epoxy-phenolic ones due to rising safety concern regarding the potential release of bisphenol A under increased regulations and consumer pressure. In this study, hazard linked to the migration of non-intentionally added substances from a single polyester-coated tin plate (5 batches) to canned food has been studied. Migration tests were performed using acetonitrile (ACN) and ethanol (EtOH) 95 %. Non-targeted analyses by liquid chromatography-high-resolution mass spectrometry revealed the presence of four cyclic oligoesters classified as Cramer class III substances with an estimated exposure (calculated for French population only) below the threshold of toxicological concern value of 1.5 µg/kg b.w./day, suggesting a no safety concern. Moreover, migrates were tested using in vitro genotoxicity DNA damage response (DDR) test and mini mutagenicity test (MMT) with different strains of S. Typhimurium using direct incorporation (TA100, TA98, TA102, TA1537) and pre-incubation (TA100, TA98) methods. Samples were negative in both bioassays suggesting the absence of genotoxicity/mutagenicity of the mixtures. To verify any false negative response due to matrix effect, migrates were spiked with corresponding positive controls in parallel with the MMT and the DDR test. No matrix effect was observed in these experimental conditions.

In vitro assessment of Momordica charantia/Hypericum perforatum oils loaded PCL/Collagen fibers: Novel scaffold for tissue engineering.

The research on tissue engineering applications has been progressing to manufacture ideal tissue scaffold biomaterials. In this study, a double-layered electrospun biofiber scaffold biomaterial including Polycaprolactone (PCL)/Collagen (COL) fibrous inner layer and PCL/ Momordica charantia (MC) and Hypericum perforatum (HP) oils fibrous outer layer was developed to manufacture a functional, novel tissue scaffold with the advantageous mechanical and biological properties. The main approach was to combine the natural perspective using medicinal oils with an engineering point of view to fabricate a potential functional scaffold for tissue engineering. Medicinal plants MC and HP are rich in functional oils and incorporation of them in a tissue scaffold will unveil their potential to augment both new tissue formation and wound healing. In this study, a novel double-layered scaffold prototype was fabricated using electrospinning technique with two PCL fiber layers, first is composed of collagen, and second is composed of oils extracted from medicinal plants. Initially, the composition of plant oils was analyzed. Thereafter the biofiber scaffold layers were fabricated and were evaluated in terms of morphology, physicochemistry, thermal and mechanical features, wettability, in vitro bio-degradability. Double-layered scaffold prototype was further analyzed in terms of in vitro biocompatibility and antibacterial effect. The medicinal oils blend provided antioxidant and antibacterial properties to the novel PCL/Oils layer. The results signify that inner PCL/COL layer exhibited advanced biodegradability of 8.5% compared to PCL and enhanced wettability with 11.7° contact angle. Strength of scaffold prototype was 5.98 N/mm2 thanks to the elastic PCL fibrous matrix. The double-layered functional biofiber scaffold enabled 92% viability after 72 h contact with fibroblast cells and furthermore provided feasible attachment sites for the cells. The functional scaffold prototype's noteworthy mechanical, chemical, and biological features enable it to be suggested as a different novel biomaterial with the potential to be utilized in tissue engineering applications.

Cost-effective production of bioplastic polyhydroxybutyrate via introducing heterogeneous constitutive promoter and elevating acetyl-Coenzyme A pool of rapidly growing cyanobacteria.

Bioplastic production using cyanobacteria can be an effective strategy to cope with environmental problems caused by using petroleum-based plastics. Synechococcus elongatus UTEX 2973 with heterogeneous phaCAB can produce bioplastic polyhydroxybutyrate (PHB) with a high CO2 uptake rate. For cost-effective production of PHB in S. elongatus UTEX 2973, phaCAB was expressed by the constitutive Pcpc560, resulting in the production of 226 mg/L of PHB by only photoautotrophic cultivation without the addition of inducer. Several culture conditions were applied to increase PHB productivity, and when acetate was supplied at a concentration of 1 g/L as an organic carbon source, productivity significantly increased resulting in 607.2 mg/L of PHB and additive cost reduction of more than 300 times was achieved compared to IPTG. Consequently, these results suggest the possibility of cyanobacteria as an agent that can economically produce PHB and as a solution to the problem of petroleum-based plastics.

Performance assessment of an injectable hyaluronic acid/polylactic acid complex hydrogel with enhanced biological properties as a dermal filler.

Injectable hyaluronic acid (HA) hydrogel plays an important role in dermal filling. However, conventional HA dermal fillers mostly lack bio-functional diversity and frequently cause adverse reactions because of the chemical stiffness of highly modified degree and crosslinker residues. In this study, polylactic acid (PLA) was embedded into HA hydrogel as a bioactive substance and 1,4-butanediol diglycidyl ether was used as a crosslinker to prepare the HA/PLA composite hydrogel with enhanced biocompatibility and biological performance. We aimed to investigate the properties of HA/PLA composite hydrogels as dermal fillers by assessing the rheological properties, surface microstructure, enzymolysis stability, swelling ratio, degradation rate, cytotoxicity, and anti-wrinkle effect on photo-aged skin. The results showed that the stability and stiffness of the composite hydrogel decreased with an increasing amount of PLA, while the in vivo safety of the HA/PLA hydrogel was enhanced, showing no adverse reactions such as edema, redness, or swelling. Moreover, the composite hydrogel with 2 wt% PLA exhibited excellent anti-wrinkle effects, showing the highest collagen production. Thus, the PLA-embedded HA composite hydrogel showed potential as a dermal filler with high safety, easy injectability, and excellent anti-wrinkle effects.

Process modelling for industrial scale polyhydroxybutyrate production using fructose, formic acid and CO2: Assessing carbon sources and economic viability.

Polyhydroxybutyrate (PHB) is a biodegradable polymer that has potential to replace petroleum-derived plastics. However, the commercialisation of PHB is hindered by high production costs. In this study, the material flow and economics of an industrial scale PHB production process using fructose, formic acid and carbon dioxide (CO2) as carbon sources were simulated and analysed. The lowest breakeven price of 3.64 $/kg PHB was obtained when fructose was utilized as carbon source. When formic acid and CO2 were used, the breakeven price was 10.30 and 10.24 $/kg PHB due to raw material cost, respectively. Although using formic acid and CO2 is more expensive, they meet the emerging sustainable needs for plastic production and contribute to the circular economy via CO2 fixation. This study suggests that the use of formic acid and CO2 as feedstock for PHB production has potential to become competitive in the bioplastic market with further research.

Recovery of energy and carbon fibre from wind turbine blades waste (carbon fibre/unsaturated polyester resin) using pyrolysis process and its life-cycle assessment.

Recovery of carbon fibres and resin from wind turbine blade waste (WTB) composed of carbon fibres (CF)-reinforced unsaturated polyester resin (UPR) has been environmentally challenging due to its complex structure that is not biodegradable and that is rich in highly toxic styrene (main component of UPR). Within this framework, this paper aims to liberate CF and UPR from WTB using a pyrolysis process. The treatment was performed on commercial WTB (CF/UPR) up to 600 °C using a 250 g reactor. The UPR fraction was decomposed into liquid and gaseous phases, while CF remained as a residue. The composition of gaseous phase was monitored during the entire treatment using a digital gas analyser, while gas chromatography-mass spectrometry (GC-MS) was used to characterize the collected liquid phase. CF fraction was collected and exposed to additional oxidation process after treatment at 450 °C for purification propose, then it was analysed using FTIR and SEM-EDX. Finally, the life cycle assessment (LCA) of the CF/UPR pyrolysis was studied using SimaPro software and the results were compared with landfill disposal practices. The pyrolysis results manifested that 500 °C was sufficient for UPR decomposition into styrene-rich oil and gaseous products with yields of 15.23 wt% and 6.83 wt%, respectively, accompanied by 77.93 wt% solid residue including CF. The LCA results showed that pyrolysis with oxidation process has high environmental potential in WTB recycling with significant reduction in several impact categories compared to landfill. However, the pyrolysis scenario revealed several additional environmental burdens related to ecosystems, acidification, Ozone formation, and fine particulate matter formation that must be overcome before upscaling.

Synergistic approach for enhanced production of polyhydroxybutyrate by Bacillus pseudomycoides SAS-B1: Effective utilization of glycerol and acrylic acid through fed-batch fermentation and its environmental impact assessment.

The continual rise in the consumption of petroleum-based synthetic polymers raised a significant environmental concern. Bacillus pseudomycoides SAS-B1 is a gram-positive rod-shaped halophilic bacterium capable of accumulating Polyhydroxybutyrate (PHB)-an intracellular biodegradable polymer. In the present study, the optimal conditions for cell cultivation in the seed media were developed. The optimal factors included a preservation age of 14 to 21 days (with 105 to 106 cells/mL), inoculum size of 0.1 % (w/v), 1 % (w/v) glucose, and growth temperature of 30 °C. The cells were then cultivated in a two-stage fermentation process utilizing glycerol and Corn Steep Liquor (CSL) as carbon and nitrogen sources, respectively. PHB yield was effectively increased from 2.01 to 9.21 g/L through intermittent feeding of glycerol and CSL, along with acrylic acid. FTIR, TGA, DSC, and XRD characterization studies were employed to enumerate the recovered PHB and determine its physicochemical properties. Additionally, the study assessed the cradle-to-gate Life Cycle Assessment (LCA) of PHB production, considering net CO2 generation and covering all major environmental impact categories. The production of 1000 kg of PHB resulted in lower stratospheric ozone depletion and comparatively reduced carbon dioxide emissions (2022.7 kg CO2 eq.) and terrestrial ecotoxicity (9.54 kg 1,4-DCB eq.) than typical petrochemical polymers.

Green and economic flame retardant prepared by the one-step method for polylactic acid.

Resolving the flammability of poly(L-lactic acid) (PLA) while ensuring its environmental friendliness and preserving key flame retardancy and mechanical properties represents a critical challenge. We have successfully developed a highly efficient and environmentally friendly flame retardant called Hexamethylenediamine tetramethylene phosphonic acid amine (HDME). The flame retardancy of PLA/HDME composites was significantly improved, as indicated by the LOI value of 29.1 % and UL-94 V-0 rating for PLA/3.5 HDME with only 3.5 % HDME addition. The results show a 23.4 % reduction in the total heat release (THR), a 40.0 % increase in the time to ignition (TTI), and a 21.2 % increase in the flame propagation index (FPI) compared to original PLA. Flame retardant mechanism of HDME involves the gas phase, condensed phase, and interrupted heat exchange effects. The HDME also preserved the original mechanical properties of PLA, with the elongation at break and tensile strength retention of PLA/3.5 HDME reaching 93.05 % and 89.65 %. This work provides a simple and efficient method for flame retardant modification of PLA, which can expand its application scope.