Bioactive and Hemocompatible PLA/Lignin Bio-Composites: Assessment of In Vitro Antioxidant Activity for Biomedical Applications.

In this study, acetylated soda lignin (ASL) and non-acetylated soda lignin (SL) were extruded with PLA in different concentrations to fabricate antioxidant polylactic acid (PLA)/lignin composites for potential biomedical applications. After lignin acetylation, good compatibility was observed between PLA and lignin in scanning electron microscopy images. All the PLA/ASL composites displayed higher mechanical properties than PLA/SL composites. PLA/ASL5 displayed the highest mechanical characteristics with elongation at break of 10% and tensile strength of 57 MPa, while PLA/SL15 and PLA/SL20 demonstrated superior UV-blocking potential with UV transmittance less than 10%. Addition of ASL in PLA lead to an increase in the hydrophobic character, with all the PLA/ASL displaying a higher water contact angle. The antioxidant test using 2,2-diphenyl-1-picrylhydrazyl assay showed that PLA/SL composites rendered superior radical scavenging activity (RSA), with PLA/SL20 composites displaying an RSA of 80%. Furthermore, in vitro antioxidant activity and cytocompatibility were analyzed using human colon cancer cells (HCT-15) and gastric epithelial cells (NCC-24). In vitro antioxidant activity, evaluated by H2O2 exposure was confirmed by a live/dead assay. PLA/SL composites protected both types of cells from oxidative stress. In addition, all PLA/SL and PLA/ASL composites promoted cell proliferation compared to PLA. PLA/SL5 and PLA/SL10 displayed the highest cell proliferation of all composites. Lastly, all PLA/SL and PLA/ASL composites had a hemoglobin release less than 2%. The antioxidant properties, cytocompatibility, and hemocompatibility of lignin/PLA demonstrated in our study indicate that these lignin/PLA composites possess the desirable attributes for potential biomedical applications.

Biocompatibility Assessment of Polylactic Acid (PLA) and Nanobioglass (n-BG) Nanocomposites for Biomedical Applications.

Scaffolds based on biopolymers and nanomaterials with appropriate mechanical properties and high biocompatibility are desirable in tissue engineering. Therefore, polylactic acid (PLA) nanocomposites were prepared with ceramic nanobioglass (PLA/n-BGs) at 5 and 10 wt.%. Bioglass nanoparticles (n-BGs) were prepared using a sol-gel methodology with a size of ca. 24.87 ± 6.26 nm. In addition, they showed the ability to inhibit bacteria such as Escherichia coli (ATCC 11775), Vibrio parahaemolyticus (ATCC 17802), Staphylococcus aureus subsp. aureus (ATCC 55804), and Bacillus cereus (ATCC 13061) at concentrations of 20 w/v%. The analysis of the nanocomposite microstructures exhibited a heterogeneous sponge-like morphology. The mechanical properties showed that the addition of 5 wt.% n-BG increased the elastic modulus of PLA by ca. 91.3% (from 1.49 ± 0.44 to 2.85 ± 0.99 MPa) and influenced the resorption capacity, as shown by histological analyses in biomodels. The incorporation of n-BGs decreased the PLA crystallinity (from 7.1% to 4.98%) and increased the glass transition temperature (Tg) from 53 °C to 63 °C. In addition, the n-BGs increased the thermal stability due to the nanoparticle's intercalation between the polymeric chains and the reduction in their movement. The histological implantation of the nanocomposites and the cell viability with HeLa cells higher than 80% demonstrated their biocompatibility character with a greater resorption capacity than PLA. These results show the potential of PLA/n-BGs nanocomposites for biomedical applications, especially for long healing processes such as bone tissue repair and avoiding microbial contamination.

Assessment of electrospun cardiac patches made with sacrificial particles and polyurethane-polycaprolactone blends.

Congenital heart defects (CHDs) are the leading cause of death in live-born infants. Currently, patches used in the repair of CHDs are exclusively inert and non-degradable, which increases the risk of arrhythmia, follow-up surgeries, and sudden cardiac death. In this preliminary study, we sought to fabricate biodegradable scaffolds that can support cardiac regeneration in the repair of CHDs. We electrospun biodegradable scaffolds using various blends of polyurethane (PU) and polycaprolactone (PCL) with and without sacrificial poly(ethylene oxide) (PEO) particles and assessed the mechanical properties, cell infiltration levels, and inflammatory response in vitro (surface cell seeding) and in vivo (subcutaneous mouse implant). We hypothesized that a blend of the two polymers would preserve the low stiffness of PU as well as the high cell infiltration observed in PCL scaffolds. The inclusion of PU in the blends, even as low as 10%, decreased cell infiltration both in vitro and in vivo. The inclusion of sacrificial PEO increased pore sizes, reduced Young's moduli, and reduced the inflammatory response in all scaffold types. Collectively, we have concluded that a PCL patch electrospun with sacrificial PEO particles is the most promising scaffold for further assessment as in our heart defect model.

Assessment of the hepatoprotective effect of developed lipid-polymer hybrid nanoparticles (LPHNPs) encapsulating naturally extracted ß-Sitosterol against CCl4 induced hepatotoxicity in rats.

The hepatoprotective effect of ß-Sitosterol (BSS), a natural phytosterol, after being formulated into a suitable pharmaceutical drug delivery system has not been widely explored. BSS was isolated from Centaurea pumilio L., identified and formulated as lipid-polymer hybrid nanoparticles (LPHNPs) using the poly(D,L-lactide-co-glycolide) polymer and DSPE-PEG-2000 lipid in different ratios. The selected formulation, prepared with a lipid: polymer: drug ratio of 2:2:2, had an entrapment efficiency (EE%) of 94.42 ± 3.8, particle size of 181.5 ± 11.3 nm, poly dispersity index (PDI) of 0.223 ± 0.06, zeta potential of -37.34 ± 3.21 and the highest drug release after 24 h. The hepatoprotective effect of the formulation at two different doses against CCl4 induced hepatotoxicity was evaluated in rats. The results showed that the BSS-LPHNPs (400 mg/kg) have the ability to restore the liver enzymes (alanine aminotransferase (ALT) and aspartate aminotransferase (AST)), liver lipid peroxidation markers (malondialdehyde (MDA) and catalase (CAT)), total bilirubin and albumin to their normal levels without inhibitory effect on the CYP2E1 activity. Also, the formulation could maintain the normal histological structure of liver tissue and decrease the cleaved caspase-3 expression. LPHNPs formulation encapsulating natural BSS is a promising hepatoprotective drug delivery system.

Assessment of cartilage regeneration on 3D collagen-polycaprolactone scaffolds: Evaluation of growth media in static and in perfusion bioreactor dynamic culture.

Efforts on bioengineering are directed towards the construction of biocompatible scaffolds and the determination of the most favorable microenvironment, which will better support cell proliferation and differentiation. Perfusion bioreactors are attracting growing attention as an effective, modern tool in tissue engineering. A natural biomaterial extensively used in regenerative medicine with outstanding biocompatibility, biodegradability and non-toxic characteristics, is collagen, a structural protein with undisputed beneficial characteristics. This is a study designed according to the above considerations. 3D printed polycaprolactone (PCL) scaffolds with rectangular pores were coated with collagen either as a coating on the scaffold's trabeculae, or as a gel-cell solution penetrating scaffolds' pores. We employed histological, molecular and imaging techniques to analyze colonization, proliferation and chondrogenic differentiation of Adipose Derived Mesenchymal Stem Cells (ADMSCs). Two different differentiation culture media were employed to test chondrogenic differentiation on gelated and non gelated PCL scaffolds in static and in perfusion bioreactors dynamic culture conditions. In dynamic culture, non gelated scaffolds combined with our in house TGF-ß2 based medium, augmented chondrogenic differentiation performance, which overall was significantly less favorable compared to StemPro™ propriety medium. The beneficial mechanical stimulus of dynamic culture, appears to outgrow the disadvantage of the "weaker" TGF-ß2 medium used for chondrogenic differentiation. Even though cells in static culture grew well on the scaffold, there was limited penetration inside the construct, so the purpose of the 3D culture was not fully served. In contrast dynamic culture achieved better penetration and uniform distribution of the cells within the scaffold.

Engineering a multifunctional 3D-printed PLA-collagen-minocycline-nanoHydroxyapatite scaffold with combined antimicrobial and osteogenic effects for bone regeneration.

3D-printing and additive manufacturing can be powerful techniques to design customized structures and produce synthetic bone grafts with multifunctional effects suitable for bone repair. In our work we aimed the development of novel multifunctionalized 3D printed poly(lactic acid) (PLA) scaffolds with bioinspired surface coatings able to reduce bacterial biofilm formation while favoring human bone marrow-derived mesenchymal stem cells (hMSCs) activity. For that purpose, 3D printing was used to prepare PLA scaffolds that were further multifunctionalized with collagen (Col), minocycline (MH) and bioinspired citrate- hydroxyapatite nanoparticles (cHA). PLA-Col-MH-cHA scaffolds provide a closer structural support approximation to native bone architecture with uniform macroporous, adequate wettability and an excellent compressive strength. The addition of MH resulted in an adequate antibiotic release profile that by being compatible with local drug delivery therapy was translated into antibacterial activities against Staphylococcus aureus, a main pathogen associated to bone-related infections. Subsequently, the hMSCs response to these scaffolds revealed that the incorporation of cHA significantly stimulated the adhesion, proliferation and osteogenesis-related gene expression (RUNX2, OCN and OPN) of hMSCs. Furthermore, the association of a bioinspired material (cHA) with the antibiotic MH resulted in a combined effect of an enhanced osteogenic activity. These findings, together with the antibiofilm activity depicted strengthen the appropriateness of this 3D-printed PLA-Col-MH-cHA scaffold for future use in bone repair. By targeting bone repair while mitigating the typical infections associated to bone implants, our 3D scaffolds deliver an integrated strategy with the combined effects further envisaging an increase in the success rate of bone-implanted devices.

[Development and assessment of efficacy of L-polylactide matrix for creation of a tissue-engineered vascular graft]. / Razrabotka i otsenka éffektivnosti matritsy iz L-polilaktida dlia sozdaniia tkaneinzhenernogo sosudistogo implantata.

In order to create a tissue-engineered vascular graft we elaborated a matrix consisting of nanofibres of biodegradable polymer L-polylactide. We worked out the methodology of crystallization of the matrix on a rod, making it possible to manufacture specimens possessing strength and deformity characteristics superior to those of native vessels. This was followed by a series of chronic experiments on implanting the elaborated matrix into the abdominal aorta of rats for the duration of up to 16 months. We obtained satisfactory parameters of the patency of the matrices (71%). According to the findings of histological examination, in the course of time there occurred biodegradation of the matrix and formation of a new vascular wall, with no evidence of either inflammation or neointimal hyperplasia in the zone of the anastomoses. Resorption of the polymeric fibres commenced 12 weeks after exposure and completely terminated after 64 weeks. By that time, both neointima and neoadventitia were formed, whose composition and structure were close to those of the native vessel. Insufficiently high mechanical properties of the zone of reconstruction turned out to be the cause of the formation of aneurysms.

Fabrication, characterization, and biocompatibility assessment of a novel elastomeric nanofibrous scaffold: A potential scaffold for soft tissue engineering.

With regard to flexibility and strength properties requirements of soft biological tissue, elastomeric materials could be more beneficial in soft tissue engineering applications. The present work investigates the use of an elastic polymer, (polycaprolactone fumarate [PCLF]), for fabricating an electrospun scaffold. PCLF with number-average molecular weight of 13,284 g/mol was synthetized, electrospun PCLF:polycaprolactone (PCL) (70:30) nanofibrous scaffolds were fabricated and a novel strategy (in situ photo-crosslinking along with wet electrospinning) was applied for crosslinking of PCLF in the structure of PCLF:PCL nanofibers was presented. Sol fraction results, Fourier-transform infrared spectroscopy, and mechanical tests confirmed occurrence of crosslinking reaction. Strain at break and Young's modulus of crosslinked PCLF:PCL nanofibers fabricated was found to be 114.5 ± 3.9% and 0.6 ± 0.1 MPa, respectively, and dynamic mechanical analysis results revealed elasticity of nanofibers. MTS assay showed biocompatibility of PCLF:PCL (70:30) nanofibrous scaffolds. Our overall results showed that electrospun PCLF:PCL nanofibrous scaffold could be considered as a candidate for further in vitro and in vivo experiments and its application for engineering of soft tissues subjected to in vivo cyclic mechanical stresses. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 2371-2383, 2018.

Assessment of polycaprolacton (PCL) nanocomposite scaffold compared with hydroxyapatite (HA) on healing of segmental femur bone defect in rabbits.

Segmental bone loss due to trauma, infection, and tumor resection and even non-union results in the vast demand for replacement and restoration of the function of the lost bone. The objective of this study is to utilize novel inorganic-organic nanocomposites for biomedical applications. Biodegradable implants have shown great promise for the repair of bone defects and have been commonly used as bone substitutes, which traditionally would be treated using metallic implants. In this study, 45 mature male New Zealand white rabbits 6-8 months and weighting 3-3.5 kg were examined. Rabbits were divided into three groups. Surgical procedures were done after an intramuscular injection of Ketamine 10% (ketamine hydrochloride, 50 mg/kg), Rompun 5% (xylazine, 5 mg/kg). Then an approximately 6 mm diameter - 5 mm cylinder bone defect was created in the femur of one of the hind limbs. After inducing the surgical wound, all rabbits were colored and randomly divided into three experimental groups of nine animals each: Group 1 received medical pure nanocomposite polycaprolactone (PCL) granules, Group 2 received hydroxyapatite and Group 3 was a control group with no treatment. Histopathological evaluation was performed on days 15, 30 and 45 after surgery. On day 45 after surgery, the quantity of newly formed lamellar bone in the healing site in PCL group was better than onward compared with HA and control groups. Finally, nanocomposite PCL granules exhibited a reproducible bone-healing potential.

Assessment of Scaffolding Properties for Chondrogenic Differentiation of Adipose-Derived Mesenchymal Stem Cells in Nasal Reconstruction.

IMPORTANCE: Nasal reconstruction in patients who are missing a significant amount of structural nasal support remains a difficult challenge. One challenge is the deficiency of cartilage left within the nose as a consequence of rhinectomy or a midline destructive disease. Historically, the standard donor source for large quantities of native cartilage has been costal cartilage. OBJECTIVE: To enable the development of protocols for new mesenchymal stem cell technologies as alternative procedures with reduced donor site morbidity, risk of infection and extrusion. DESIGN, SETTING, AND MATERIALS: We examined 6 popular scaffold materials in current practice in terms of their biodegradability in tissue culture, effect on adipose-derived mesenchymal stem cell growth, and chondrogenic fate commitment. Various biomaterials of matching size, porosity, and fiber alignment were synthesized by electrospinning and overlaid with rabbit adipose-derived mesenchymal cells in media supplemented or not with chondrogenic factors. Experiments were performed in vitro using as end points biomarkers for cell growth and chondrogenic differentiation. Polydioxanone (PDO), poly-3-hydroxybutyrate-co-3-hydroxyvalerate (PHBV), PHBV-polycaprolactone, poly(L-lactide-co-caprolactone), poly(lactic-co-glycolic acid), and polystyrene scaffolds of 60% to 70% porosity and random fiber alignment were coated with poly(L)-lysine/laminin to promote cell adhesion and incubated for 28 days with 2.5 to 3.5 × 105 rabbit adipose mesenchymal cells. MAIN OUTCOMES AND MEASURES: Cell growth was measured by fluorometric DNA quantitation and chondrogenic differentiation of stem cells by spectrophotometric sulfated glycosaminoglycan (sGAG) assay. Microscopic visualization of cell growth and matrix deposition on formalin-fixed, paraffin-embedded tissue sections was performed, respectively, with nuclear fast red and Alcian blue. RESULTS: Of 6 scaffold materials tested using rabbit apidose mesenchymal cells, uncoated scaffolds promoted limited cell adhesion but coating with poly(L)-lysine/laminin enabled efficient cell saturation of scaffold surfaces, albeit with limited involvement of scaffold interiors. Similar growth rates were observed under these conditions, based on DNA content analysis. However, PDO and PHBV/PCL scaffolds supported chondrogenic fate commitment better than other materials, based on soluble sGAG analysis and microscopic observation of chondrogenic matrix deposition. The mean (SD) sGAG scaffold values expressed as fold increase over control were PDO, 2.26 (0.88), PHBV/PCL, 2.09 (0.83), PLCL, 1.36 (0.39), PLGA, 1.34 (0.77), PHBV, 1.07 (0.31), and PS, 0.38 (0.14). CONCLUSIONS AND RELEVANCE: These results establish materials, reagents, and protocols for tissue engineering for nasal reconstruction using single-layer, chondrogenically differentiated, adipose-derived mesenchymal stem cells. Stackable, scaffold-supported, multisheet bioengineered tissue may be generated using these protocols. LEVEL OF EVIDENCE: NA.

Two for the Price of One: PAMAM-Dendrimers with Mixed Phosphoryl Choline and Oligomeric Poly(Caprolactone) Surfaces.

The application of dendrimers for biological and medical purposes is highly dependent on the type of surface group in relation to cytotoxicity. Since amine terminated PAMAM dendrimers have been shown to have toxic properties and thereby limited applications in the medical field, the discovery of a new nontoxic surface coating is of great interest. In the present work, amine terminated DAB-PAMAM dendrimers from generation zero to four have been coated with statistical surface functionalization giving a dendrimer surface consisting of an approximately 1:1 mixture of zwitterionic phosphoryl choline hexanamide and 6-((6-hydroxyhexanoyl)oxy)hexanamide. The cytotoxic properties of generation two to four were tested on three different human cancer cell lines, SKBR3 human breast cancer cells, HeLa human cervical cancer cells, and Hep G2 human hepatocellular liver carcinoma cells and compared to the toxicity of amine terminated PAMAM dendrimers. In addition to lower cytotoxicity than observed for amine terminated dendrimers, the coated dendrimers showed minor cytotoxicity against all three human cell lines, negligible influence on ROS generation and mitochondrial membrane potential. These observations support the conclusion that the analyzed group of phosphorylcholine dendrimers may be suitable for medical applications.

Biological and Tribological Assessment of Poly(Ethylene Oxide Terephthalate)/Poly(Butylene Terephthalate), Polycaprolactone, and Poly (L\DL) Lactic Acid Plotted Scaffolds for Skeletal Tissue Regeneration.

Additive manufactured scaffolds are fabricated from three commonly used biomaterials, polycaprolactone (PCL), poly (L\DL) lactic acid (P(L\DL)LA), and poly(ethylene oxide terephthalate)/poly(butylene terephthalate) (PEOT/PBT). Scaffolds are compared biologically and tribologically. Cell-seeded PEOT/PBT scaffolds cultured in osteogenic and chondrogenic differentiation media show statistical significantly higher alkaline phosphatase (ALP) activity/DNA and glycosaminoglycans (GAG)/DNA ratios, followed by PCL and P(L\DL)LA scaffolds, respectively. The tribological performance is assessed by determining the friction coefficients of the scaffolds at different loads and sliding velocities. With increasing load or decreasing sliding velocity, the friction coefficient value decreases. PEOT/PBT show to have the lowest friction coefficient value, followed by PCL and P(L\DL)LA. The influence of the scaffold architecture is further determined with PEOT/PBT. Reducing of the fiber spacing results in a lower friction coefficient value. The best and the worst performing scaffold architecture are chosen to investigate the effect of cell culture on the friction coefficient. Matrix deposition is low in the cell-seeded scaffolds and the effect is, therefore, undetermined. Taken together, our studies show that PEOT/PBT scaffolds support better skeletal differentiation of seeded stromal cells and lower friction coefficient compared to PCL and P(L/DL)A scaffolds.

Nonwoven-based gelatin/polycaprolactone membrane proves suitability in a preclinical assessment for treatment of soft tissue defects.

Standard preclinical assessments in vitro often have limitations regarding their transferability to human beings, mainly evoked by their nonhuman and tissue-different/nontissue-specific source. Here, we aimed at employing tissue-authentic simple and complex interactive fibroblast-epithelial cell systems and their in vivo-relevant biomarkers for preclinical in vitro assessment of nonwoven-based gelatin/polycaprolactone membranes (NBMs) for treatment of soft tissue defects. NBMs were composed of electrospun gelatin and polycaprolactone nanofiber nonwovens. Scanning electron microscopy in conjunction with actin/focal contact integrin fluorescence revealed successful adhesion and proper morphogenesis of keratinocytes and fibroblasts, along with cells' derived extracellular matrix deposits. The "feel-good factor" of cells under study on the NBM was substantiated by forming a confluent connective tissue entity, which was concomitant with a stratified epithelial equivalent. Immunohistochemistry proved tissue authenticity over time by abundance of the biomarker vimentin in the connective tissue entity, and chronological increase of keratins KRT1/10 and involucrin expression in epithelial equivalents. Suitability of the novel NBM as wound dressing was evidenced by an almost completion of epithelial wound closure in a pilot mini-pig study, after a surgical intervention-caused gingival dehiscence. In summary, preclinical assessment by tissue-authentic cell systems and the animal pilot study revealed the NBM as an encouraging therapeutic medical device for prospective clinical applications.

Layer-by-layer assembly of antibacterial coating on interbonded 3D fibrous scaffolds and its cytocompatibility assessment.

Bonded fibrous matrices have shown great potential in tissue engineering because of their unique 3D structures and pore characteristics. For some applications, bacterial infections must be taken into account, and antibacterial function is highly desired. In this study, an antibacterial polymer, polyhexamethylene biguanide (PHMB), was applied onto the fiber surface of a bonded poly(ε-caprolactone) (PCL) fibrous matrix with the objective to achieve both strong antibacterial effect and good cell compatibility. The coatings were prepared by using an electrostatic layer-by-layer (LbL) assembly technique, which allowed the control of PHMB loading and coating uniformity on the fiber surface. The PHMB coating provided antibacterial activities, but had no toxicity on mammalian cells. This bonded PCL fibrous matrix with electrostatically self-assembled PHMB may provide a new antiinfective tissue scaffold for various biomedical applications.

Surface segregation assessment in poly(epsilon-caprolactone)-poly(ethylene glycol) multiblock copolymer films.

The ability to predict the in vivo performance of multiblock-copolymer-based biomaterials is crucial for their applicability in the biomedical field. In this work, XPS analysis of PCL-PEG copolymers was carried out, as well as morphological and wettability evaluations by SEM and CA measurements, respectively. XPS analysis on films equilibrated in PBS demonstrated a further enrichment in the PEG component on the surface. Copolymer films obtained by casting using different solvents showed a dependence in segregation according to the solvent employed. Cell adhesion tests demonstrated the importance of copolymer segregation and rearrangement in a wet environment, with a dependence of these phenomena on the copolymer molecular weight.

Mechanical and radiological assessment of the influence of rhTGFbeta-3 on bone regeneration in a segmental defect in the ovine tibia: pilot study.

Limitations in the use of autologous bone graft, which is the gold standard therapy in bone defect healing, drive the search for alternative treatments. In this study the influence of rhTGFbeta-3 on mechanical and radiological parameters of a healing bone defect in the sheep tibia was assessed. In the sheep, an 18-mm long osteoperiosteal defect in the tibia was treated by rhTGFbeta-3 seeded on a poly(L/DL-lactide) carrier (n = 4). In a second group (n = 4), the defect was treated by the carrier only, in a third group (n = 4) by autologous cancellous bone graft, and in a fourth group (n = 2) the defect remained blank. The healing process of the defect was assessed by weekly in vivo stiffness measurements and radiology as well as by quantitative computed tomographic assessment of bone mineral density (BMD) every 4 weeks. The duration of the experiment was 12 weeks under loading conditions. In the bone graft group, a marginally significant higher increase in stiffness was observed than in the PLA/rhTGFbeta-3 group (p = 0.06) and a significantly higher increase than in the PLA-only group (p = 0.03). The radiographic as well as the computed tomographic evaluation yielded significant differences between the groups (p = 0.03), indicating the bone graft treatment (bone/per area, 83%; BMD, 0.57 g/cm(3)) performing better than the PLA/rhTGFbeta-3 (38%; 0.23 g/cm(3)) and the PLA-only treatment (2.5%; 0.09 g/cm(3)), respectively. Regarding the mechanical and radiological parameters assessed in this study, we conclude that rhTGFbeta-3 has a promoting effect on bone regeneration. However, under the conditions of this study, this effect does not reach the potential of autologous cancellous bone graft transplantation.