Hazard assessment of hexagonal boron nitride and hexagonal boron nitride reinforced thermoplastic polyurethane composites using human skin and lung cells.

Hexagonal boron nitride (hBN) is an emerging two-dimensional material attracting considerable attention in the industrial sector given its innovative physicochemical properties. Potential risks are associated mainly with occupational exposure where inhalation and skin contact are the most relevant exposure routes for workers. Here we aimed at characterizing the effects induced by composites of thermoplastic polyurethane (TPU) and hBN, using immortalized HaCaT skin keratinocytes and BEAS-2B bronchial epithelial cells. The composite was abraded using a Taber® rotary abraser and abraded TPU and TPU-hBN were also subjected to photo-Fenton-mediated degradation mimicking potential weathering across the product life cycle. Cells were exposed to the materials for 24 h (acute exposure) or twice per week for 4 weeks (chronic exposure) and evaluated with respect to material internalization, cytotoxicity, and proinflammatory cytokine secretion. Additionally, comprehensive mass spectrometry-based proteomics and metabolomics (secretomics) analyses were performed. Overall, despite evidence of cellular uptake of the material, no significant cellular and/or protein expression profiles alterations were observed after acute or chronic exposure of HaCaT or BEAS-2B cells, identifying only few pro-inflammatory proteins. Similar results were obtained for the degraded materials. These results support the determination of hazard profiles associated with cutaneous and pulmonary hBN-reinforced polymer composites exposure.

Novel Peripheral Intravenous Catheter Securement for Children and Catheter Failure Reduction: A Randomized Clinical Trial.

Importance: Peripheral intravenous catheters (PIVCs) facilitate essential treatment. Failure of these essential devices is frequent and new securement strategies may reduce failure and improve patient outcomes. Objective: To evaluate clinical effectiveness of novel PIVC securement technologies for children to reduce catheter failure. Design, Setting, and Participants: A 3-arm, parallel group, superiority randomized clinical trial was conducted at 2 regional Australian hospitals from February 5, 2020, to January 14, 2022. Children aged 6 months to 8 years who were anticipated to require admission with a PIVC for at least 24 hours of in hospital treatment were eligible. Data were analyzed from May 25, 2022, to February 20, 2024. Interventions: Participants were randomly allocated in a 1:1:1 ratio to standard care, bordered polyurethane (Tegaderm [3M]), integrated securement dressing (SorbaView SHIELD [Medline]), and integrated securement dressing with tissue adhesive (Secureport IV). One catheter was studied per patient. Main Outcomes and Measures: Primary outcome was PIVC failure, defined as premature cessation of PIVC function for any reason prior to completion of planned treatment. Secondary outcomes were PIVC complications (any time dislodgement, occlusion, infiltration, partial dislodgement, extravasation, device leaking, phlebitis, pain), PIVC longevity, intervention acceptability (clinicians, participants, caregivers; 0-10 scale), and pain on removal (participants and caregivers; 0-10 scale relevant to age), adverse events, and health care costs. Results: A total of 383 patients (51% female; median age 36 [25th-75th percentiles, 22-72] months) were randomized 134 to standard care, 118 to integrated securement dressing, and 131 to integrated securement dressing with tissue adhesive. PIVC failure was lowest in integrated securement dressing with tissue adhesive (15 [12%]; adjusted hazard ratio [aHR], 0.47; 95% CI, 0.26-0.84) compared with integrated securement dressing (24 [21%]; aHR, 0.78; 95% CI, 0.47-1.28) and standard care (43 [34%]). Direct costs were significantly lower for integrated securement dressing with tissue adhesive (median, Australian dollars [A$], 312 [A$1 is equal to $0.65 US dollars]; IQR, A$302-A$380) and integrated securement dressing (median, A$303; IQR, A$294-A$465) compared with standard care (median, A$341; IQR, A$297-A$592; P ≤ .002) when considering the economic burden related to failure of devices. PIVC longevity and intervention acceptability were similar across all groups. Conclusions and Relevance: In this study, PIVCs secured with integrated securement dressings and tissue adhesive, in comparison with standard care, bordered polyurethane dressings, were associated with significantly reduced PIVC failure, for children admitted to hospital via the emergency department. Further research should focus on implementation in inpatient units where prolonged dwell and reliable intravenous access is most needed. Trial Registration: Australian New Zealand Clinical Trials Registry Identifier: ACTRN12619001026112.

Autotrophic denitrification by sulfur-based immobilized electron donor for enhanced nitrogen removal: Denitrification performance, microbial interspecific interaction and functional traits.

Sulfur-driven autotrophic denitrification (SdAD) is a promising nitrogen removing process, but its applications were generally constrained by conventional electron donors (i.e., thiosulfate (Na2S2O3)) with high valence and limited bioavailability. Herein, an immobilized electron donor by loading elemental sulfur on the surface of polyurethane foam (PFSF) was developed, and its feasibility for SdAD was investigated. The denitrification efficiency of PFSF was 97.3%, higher than that of Na2S2O3 (91.1%). Functional microorganisms (i.e., Thiobacillus and Sulfurimonas) and their metabolic activities (i.e., nir and nor) were substantially enhanced by PFSF. PFSF resulted in the enrichment of sulfate-reducing bacteria, which can reduce sulfate (SO42-). It attenuated the inhibitory effect of SO42-, whereas the generated product (hydrogen sulfide) also served as an electron donor for SdAD. According to the economic evaluation, PFSF exhibited strong market potential. This study proposes an efficient and low-cost immobilized electron donor for SdAD and provides theoretical support to its practical applications.

Long-term Insights: Histopathological Assessment of Polyurethane Implant Capsules Over 24 Years.

BACKGROUND: Polyurethane (PU)-coated breast implants are known for their strong integration into breast tissue and the formation of capsules around them. However, capsular contracture can pose both aesthetic and clinical challenges. OBJECTIVES: The objectives of this study were to analyze the biological and morphological characteristics of the capsular tissue surrounding PU-coated implants, irrespective of their contracture status, and to assess their potential suitability as a flap in revisional breast surgery for capsular contracture. METHODS: A total of 23 tissue samples were harvested from the capsules surrounding PU-coated breast implants in 12 female patients during replacement or revisional surgery. We evaluated collagen abundance, cellular and vascular density, inflammation, collagen band types and alignment, synovial metaplasia, capsule thickness, and the expression of inflammatory biomarkers and myofibroblasts with immunohistochemical techniques. Scanning electron microscopy was employed to assess implant surface characteristics over time. RESULTS: We found a significant association of capsule contraction with longer implantation durations and greater implant surface roughness (P = .018 and P = .033, respectively). Synovial metaplasia was significantly more frequent in noncontracted capsules (P = .0049). Both capsule types consisted of paucicellular, type I collagen-rich compact fibrous tissue with low vascularization. There was a marked reduction in inflammatory cells within the foreign body granuloma. The expression of inflammatory biomarkers in the capsular tissue was negligible. CONCLUSIONS: Given the reduced levels of inflammatory and vascular components within the dense, fibrous capsular tissue, we consider them to be viable alternatives for capsular flaps in revisional surgery. This strategy has the potential to mimic the reconstruction achieved with acellular dermal matrix.

Large-Scale Wearable Textile-Based Sweat Sensor with High Sensitivity, Rapid Response, and Stable Electrochemical Performance.

Textile-based sweat sensors display great potential to enhance wearable comfort and health monitoring; however, their widespread application is severely hindered by the intricate manufacturing process and electrochemical characteristics. To address this challenge, we combined both impregnation coating technology and conjugated electrospinning technology to develop an electro-assisted impregnation core-spinning technology (EAICST), which enables us to simply construct a sheath-core electrochemical sensing yarn (TPFV/CPP yarn) via coating PEDOT:PSS-coated carbon fibers (CPP) with polyurethane (TPU)/polyacrylonitrile (PAN)/poloxamer (F127)/valinomycin as shell. The TPFV/CPP yarn was sewn into the fabric and integrated with a sensor to achieve a detachable feature and efficiently monitor K+ levels in sweat. By introducing EAICST, a speed of 10 m/h can be realized in the continuous preparation of the TPFV/CPP yarn, while the interconnected pores in the yarn sheath enable it to quickly capture and diffuse sweat. Besides, the sensor exhibited excellent sensitivity (54.26 mV/decade), fast response (1.7 s), anti-interference, and long-term stability (5000 s or more). Especially, it also possesses favorable washability and wear resistance properties. Taken together, this study provides a crucial technical foundation for the development of advanced wearable devices designed for sweat analysis.

Assessment of wear characteristics, longevity and stiffness of Essix-type retainers.

OBJECTIVE: To compare four commercially available Essix-type retainers in terms of longevity, wear characteristics, stiffness and their range of rigidity. MATERIALS AND METHODS: An in vitro study was conducted at Queen Mary University of London. Four groups of thermoplastic materials were included: Duran (PETG), Essix C + (Polypropylene), Vivera and Zendura (Polyurethane). A working typodont was fabricated to evaluate surface wear characteristics using a wear machine with a customized jig. Retainers were measured for tensile test, and water absorption was measured at five different time points up to 6 months after initial immersion in two different physical states and two different solutions. Hydrolytic degradation was also evaluated using FTIR spectroscopy. RESULTS: Essix C + was the most flexible retainer with Vivera the stiffest material. Zendura and Essix C + had the most surface wear (413 µm ± 80 and 652 µm ± 12, respectively) with absorption rates of up to 15 wt% in artificial saliva occurring with Zendura. Only Essix C + displayed signs of degradation following water absorption. CONCLUSIONS: All materials had characteristic levels of flexibility and were susceptible to water absorption. Duran 1.5 mm performed similarly to Vivera in relation to stiffness and wear properties. While Zendura and Vivera have similar chemical structures, they exhibited differences concerning wear resistance and water absorption. Further clinical research evaluating the clinical relevance of these laboratory findings is required. CLINICAL RELEVANCE: Characteristic patterns of wear and rigidity of four commercially available Essix-type retainers were observed. This information should help in the tailoring of retainer material on a case-by-case basis considering treatment-related factors and patient characteristics including parafunctional habits.

In Vitro and In Vivo Assessment of the Infection Resistance and Biocompatibility of Small-Molecule-Modified Polyurethane Biomaterials.

Bacterial intracellular nucleotide second messenger signaling is involved in biofilm formation and regulates biofilm development. Interference with the bacterial nucleotide second messenger signaling provides a novel approach to control biofilm formation and limit microbial infection in medical devices. In this study, we tethered small-molecule derivatives of 4-arylazo-3,5-diamino-1H-pyrazole on polyurethane biomaterial surfaces and measured the biofilm resistance and initial biocompatibility of modified biomaterials in in vitro and in vivo settings. Results showed that small-molecule-modified surfaces significantly reduced the Staphylococcal epidermidis biofilm formation compared to unmodified surfaces and decreased the nucleotide levels of c-di-AMP in biofilm cells, suggesting that the tethered small molecules interfere with intracellular nucleotide signaling and inhibit biofilm formation. The hemocompatibility assay showed that the modified polyurethane films did not induce platelet activation or red blood cell hemolysis but significantly reduced plasma coagulation and platelet adhesion. The cytocompatibility assay with fibroblast cells showed that small-molecule-modified surfaces were noncytotoxic and cells appeared to be proliferating and growing on modified surfaces. In a 7-day subcutaneous infection rat model, the polymer samples were implanted in Wistar rats and inoculated with bacteria or PBS. Results show that modified polyurethane significantly reduced bacteria by ∼2.5 log units over unmodified films, and the modified polymers did not lead to additional irritation/toxicity to the animal tissues. Taken together, the results demonstrated that small molecules tethered on polymer surfaces remain active, and the modified polymers are biocompatible and resistant to microbial infection in vitro and in vivo.

Risk assessment-based verification of the CertiPURTM limit values for toluene diamine and methylene dianiline in flexible polyurethane foam.

Flexible polyurethane foams (PUF) are used in many consumer products. PUF may contain trace levels of aromatic diamine impurities that could represent a potential health risk. The risk associated with sleeping on a PUF mattress was evaluated. Toxicity benchmarks for sensitization and non-cancer endpoints were derived from the respective points-of-departure using standard assessment factors. For the cancer endpoints, toxicity benchmarks were derived from the 25th-percentile values of animal studies. Recently published emission and migration data allowed to link exposure with the CertiPURTM voluntary quality limits of ≤5 mg.kg-1 for 2,4-toluene diamine and 4,4'-methylene dianiline in PUF. Using conservative exposure scenarios, lifetime-average daily internal doses from the combined inhalation and dermal exposures were calculated. Margins of safety for non-cancer and sensitization endpoints were >104. The theoretical excess cancer risk was ≤1.5 × 10-7. It is concluded that sleeping on a mattress that satisfies the CertiPUR limit value does not pose undue risk to consumers.

One-Stage Implant-Based Breast Reconstruction With Polyurethane-Coated Device: Standardized Assessment of Outcomes.

BACKGROUND: Nipple-sparing mastectomies (NSMs) and implant-based breast reconstructions have evolved from 2-stage reconstructions with tissue expansion and implant exchange to direct-to-implant procedures. In this study, we tested safety and efficacy of polyurethane-based implants according to standard assessment tools. OBJECTIVES: This study aimed to test safety and feasibility of polyurethane-coated implants with standardized assessment employing internationally acknowledged evaluation criteria. METHODS: Cases of NSMs followed by breast reconstruction in 1 stage with immediate prepectoral polyurethane-coated implant placement were retrospectively reviewed. Preoperative characteristics of the population have been collected. Adherence to quality assurance criteria of the Association of Breast Surgery-British Association of Plastic Reconstructive and Aesthetic Surgeons was verified. Complications were assessed with the Clavien Dindo classification, modified for the breast. Rippling, implant rotation, and malposition were also evaluated. RESULTS: Sixty-three consecutive patients underwent 74 NSMs and immediate breast reconstruction with micro polyurethane foam-coated anatomic implants. In 5 cases we had unplanned readmissions with return to the operating room under general anesthesia (6.7%) and implant loss within 3 months from breast reconstruction (5 implants, 6.7%). Postoperative complications according to Clavien Dindo were grade 1 in 6 cases (8.1%), grade 2 in 3 cases (4%), and 3b in 5 cases (6.7%). CONCLUSIONS: Polyurethane-coated implants may prevent rotation and malposition and capsular contracture in the short term. Unplanned readmission rates and implant loss rates in the short term may be slightly higher.See the abstract translated into Hindi, Portuguese, Korean, German, Italian, Arabic, Chinese, and Taiwanese online here: https://doi.org/10.1093/asj/sjad301.

Highly Stretchable and Fluorescent Visualizable Thermoplastic Polyurethane/Tetraphenylethylene Plied Yarn Strain Sensor with Heterogeneous and Cracked Structure for Human Health Monitoring.

Smart wearable technology has been more and more widely used in monitoring and prewarning of human health and safety, while flexible yarn-based strain sensors have attracted extensive research interest due to their ability to withstand greater external strain and their significant application potential in real-time monitoring of human motion and health signals. Although several strain sensors based on yarn structures have been reported, it remains challenging to strike a balance between high sensitivity and wide strain ranges. At the same time, visual signal sensing is expected to be used in strain sensors thanks to its intuitiveness. In this work, thermoplastic polyurethane (TPU) and tetraphenylethylene (TPE) were wet-spun to fabricate flexible fluorescent fibers used as the substrate of the sensor, followed by the drop addition of polydimethylsiloxane (PDMS) beads and curing to produce a heterogeneous structure, which were further twisted into a plied yarn. Finally, a visualizable flexible yarn strain sensor based on solidified liquid beads and crack structure was obtained by loading polydopamine (PDA) and polypyrrole (PPy) in situ. The sensor exhibited high sensitivity (the GF value was 58.9 at the strain range of 143-184%), a wide working strain range (0-184%), a low monitoring limit (<0.1%), a fast response (58.82 ms), reliable responses at different frequencies, and excellent cycle durability (over 2000 cycles). At the same time, the yarn strain sensor also had excellent photothermal characteristics and a fluorescence crack visualization effect. These attractive advantages enabled yarn strain sensors to accurately monitor various human activities, showing great application potential in health monitoring, personalized medical diagnosis, and other aspects.

Strain Sensors Made of MXene, CNTs, and TPU/PSF Asymmetric Structure Films with Large Tensile Recovery and Applied in Human Health Monitoring.

Designing flexible wearable sensors with a wide sensing range, high sensitivity, and high stability is a vulnerable research direction with a futuristic field to study. In this paper, Ti3C2Tx MXene/carbon nanotube (CNT)/thermoplastic polyurethane (TPU)/polysulfone (PSF) composite films with excellent sensor performance were obtained by self-assembly of conductive fillers in TPU/PSF porous films with an asymmetric structure through vacuum filtration, and the porous films were prepared by the phase inversion method. The composite films consist of the upper part with finger-like "cavities" filled by MXene/CNTs, which reduces the microcracks in the conductive network during the tensile process, and the lower part has smaller apertures of a relatively dense resin cortex assisting the recovery process. The exclusive layer structure of the MXene/CNTs/TPU/PSF film sensor, with a thickness of 46.95 µm, contains 0.0339 mg/cm2 single-walled carbon nanotubes (SWNTs) and 0.348 mg/cm2 MXene only, providing functional range (0-80.7%), high sensitivity (up to 1265.18), and excellent stability and durability (stable sensing under 2300 fatigue tests, viable to the initial resistance), endurably cycled under large strains with serious damage to the conductive network. Finally, the MXene/CNTs/TPU/PSF film sensor is usable for monitoring pulse, swallow, tiptoe, and various joint bends in real time and distributing effective electrical signals. This paper implies that the MXene/CNTs/TPU/PSF film sensor has broad prospects in pragmatic applications.

Dynamic Characterization of a Low-Cost Fully and Continuously 3D Printed Capacitive Pressure-Sensing System for Plantar Pressure Measurements.

In orthopedics, the evaluation of footbed pressure distribution maps is a valuable gait analysis technique that aids physicians in diagnosing musculoskeletal and gait disorders. Recently, the use of pressure-sensing insoles to collect pressure distributions has become more popular due to the passive collection of natural gait data during daily activities and the reduction in physical strain experienced by patients. However, current pressure-sensing insoles face the limitations of low customizability and high cost. Previous works have shown the ability to construct customizable pressure-sensing insoles with capacitive sensors using fused-deposition modeling (FDM) 3D printing. This work explores the feasibility of low-cost fully and continuously 3D printed pressure sensors for pressure-sensing insoles using three sensor designs, which use flexible thermoplastic polyurethane (TPU) as the dielectric layer and either conductive TPU or conductive polylactic acid (PLA) for the conductive plates. The sensors are paired with a commercial capacitance-to-voltage converter board to form the sensing system. Dynamic sensor performance is evaluated via sinusoidal compressive tests at frequencies of 1, 3, 5, and 7 Hz, with pressure levels varying from 14.33 to 23.88, 33.43, 52.54, and 71.65 N/cm2 at each frequency. Five sensors of each type are tested. Results show that all sensors display significant hysteresis and nonlinearity. The PLA-TPU sensor with 10% infill is the best-performing sensor with the highest average sensitivity and lowest average hysteresis and linearity errors. The range of average sensitivities, hysteresis, and linearity errors across the entire span of tested pressures and frequencies for the PLA-TPU sensor with 10% infill is 11.61-20.11·10-4 V/(N/cm2), 11.9-31.8%, and 9.0-22.3%, respectively. The significant hysteresis and linearity error are due to the viscoelastic properties of TPU, and some additional nonlinear effects may be due to buckling of the infill walls of the dielectric.

A novel, efficient and economical alternative for the removal of toxic organic, inorganic and pathogenic water pollutants using GO-modified PU granular composite.

Multicomponent wastewater treatment utilising simple and cost-effective materials and methods is an important research topic. This study has reported the fabrication and utilisation of graphene oxide (GO) embedded granular Polyurethane (PU) (GOPU) adsorbent for the treatment of lead ion (Lead ion (Pb(II)), Methylene blue (MB), and E. coli. PU granules were wrapped with GO flakes to improve hydrophilicity, interaction with polluted water, cation-exchange reaction, and binding of pollutants on its surface. Synthesised GOPU granules were characterised by X-Ray Diffraction (XRD), Raman, Fourier transform infrared (FTIR) spectroscopy, and Scanning electron microscopy (SEM) analysis to ensure the successful synthesis of GO and fabrication of GOPU granules. Further, batch and continuous adsorption processes were studied in different operating conditions to evaluate the performance of GOPU granules in practical applications. The kinetic and isotherm analyses revealed that the adsorption of Lead (Pb(II)) ion and Methylene Blue (MB) dye followed the Freundlich and Langmuir isotherm models, respectively, and they showed good agreement with the Pseudo-second-order kinetic model. The adsorption capacities of GOPU granules for the elimination of Pb(II) and MB dye were about 842 mg/g and 899 mg/g, respectively. Additionally, investigations into the fixed bed column revealed that the adsorption column performed best at a flow rate of 5 mL/min and a bed height of 6 cm. Pb(II) adsorption had a bed uptake capacity (qbed) of 88 mg/g and percentage removal efficiency (%R) of 76%. Similarly, MB adsorption had a bed uptake capacity of 202 mg/g and a percentage removal efficiency of 71%. A systematic invention on antibacterial activity toward E. coli showed that The GOPU granules have a removal efficiency of about 100% at an exposure of 24 h. These findings indicated the possible use of GOPU granules as promising adsorbents for various water pollutants.

L-cysteine aided polyaniline capped SrO2 nanoceramics: Assessment of MC3T3-E1-arbitrated osteogenesis and anti-bactericidal efficacy on the polyurethane 2D nanofibrous substrate.

Fabricating bioartificial bone graft ceramics retaining structural, mechanical, and bone induction properties akin to those of native stem-cell niches is a major challenge in the field of bone tissue engineering and regenerative medicine. Moreover, the developed materials are susceptible to microbial invasion leading to biomaterial-centered infections which might limit their clinical translation. Here, we successfully developed biomimetic porous scaffolds of polyurethane-reinforcedL-cysteine-anchored polyaniline capped strontium oxide nanoparticles to improve the scaffold's biocompatibility, osteo-regeneration, mechanical, and antibacterial properties. The engineered nanocomposite substrate PU/L-Cyst-SrO2 @PANI (0.4 wt%) significantly promotes bone repair and regeneration by modulating osteolysis and osteogenesis. ALP activity, collagen-I, ARS staining, as well as biomineralization of MC3T3-E1 cells, were used to assess the biocompatibility and cytocompatibility of the developed scaffolds in vitro, confirming that the scaffold provided a favorable microenvironment with a prominent effect on cell growth, proliferation, and differentiation. Furthermore, osteogenic protein markers were studied using qRT-PCR with expression levels of runt-related transcription factor 2 (RUNX2), secreted phosphoprotein 1 (Spp-I), and collagen type I (Col-I). The overall results suggest that PU/L-Cyst-SrO2 @PANI (0.4 wt%) scaffolds showed superior interfacial biocompatibility, antibacterial properties, load-bearing ability, and osteoinductivity as compared to pristine PU. Thus, prepared bioactive nanocomposite scaffolds perform as a promising biomaterial substrate for bone tissue regeneration.

Flexible stretchable low-energy X-ray (30-80 keV) radiation shielding material: Low-melting-point Ga1In1Sn7Bi1 alloy/thermoplastic polyurethane composite.

A highly flexible stretchable thermoplastic polyurethane (TPU) composite loaded with a low-melting-point Ga1In1Sn7Bi1 multiprincipal element alloy (LMPEA) was prepared, and its radiation shielding performance was evaluated. The fluid characteristic of LMPEA and the flexibility of TPU enable good interface compatibility. Ga1In1Sn7Bi1 LMPEA consists of two eutectic structures, and the liquid gallium-rich phases are distributed at the boundary of the InBi intermetallic compound and Sn solid solution. In the low-photon energy range of 30-80 keV, LMPEA has a theoretical specific lead equivalent of 0.803 mmPb/mm and a theoretical weight reduction of 17.27% compared with lead. To evaluate the photon attenuation capability for the LMPEA/TPU composites, the Phy-X procedure and Monte Carlo simulations were used to determine the shielding parameters, such as the mass attenuation coefficient, linear attenuation coefficient, half-value layer, tenth-value layer, mean free path, effective atomic number, and fast neutron removal cross section. The attenuation performance test of X-ray protective materials measured the actual lead equivalent. At the same thickness, the LMPEA/TPU composite (66.667, 50.000 wt% LMPEA loading) has a higher measured lead equivalent than the in-service medical shielding materials, which meets the lead equivalent requirements of X-ray protective clothing. LMPEA/TPU composites are nontoxic, lightweight, and have excellent low-energy X-ray shielding ability, offering great potential for application in medical wearable materials.

A Retrospective Assessment of Midline Catheter Failures Focusing on Catheter Composition.

Vascular access specialists are responsible for assessing the patient in their unique situation and determining the correct vascular access device to complete the therapeutic goal without complication or failure. This retrospective cohort study compared the failure rates of a variety of polyurethane (PU) midline catheters and a midline catheter constructed of an emerging hydrophilic biomaterial (HBM). A total of 205 patients received a midline catheter and were situationally randomized by the facility where they received it. Patients who had received a midline catheter between March 2021 and May 2021 were assessed for catheter-related failures leading to increased staff time, delays in treatment, or replacement with a new vascular access device to complete the therapy. There were 101 patients in the PU cohort and 104 patients in the HBM cohort. Comparing overall failure rates between the groups revealed a 23.8% failure rate in the PU control group and only a 3.8% failure rate in the HBM group. This suggests that a midline catheter constructed of HBM biomaterial is associated with significantly lower rates of failure, thereby improving patient experience and health care economics.

Hybrid fibroin/polyurethane small-diameter vascular grafts: from fabrication toin vivopreliminary assessment.

To address the need of alternatives to autologous vessels for small-calibre vascular applications (e.g. cardiac surgery), a bio-hybrid semi-degradable material composed of silk fibroin (SF) and polyurethane (Silkothane®) was herein used to fabricate very small-calibre grafts (Øin= 1.5 mm) via electrospinning. Bio-hybrid grafts werein vitrocharacterized in terms of morphology and mechanical behaviour, and compared to similar grafts of pure SF. Similarly, two native vessels from a rodent model (abdominal aorta and vena cava) were harvested and characterized. Preliminary implants were performed on Lewis rats to confirm the suitability of Silkothane® grafts for small-calibre applications, specifically as aortic insertion and femoral shunt. The manufacturing process generated pliable grafts consisting of a randomized fibrous mesh and exhibiting similar geometrical features to rat aortas. Both Silkothane® and pure SF grafts showed radial compliances in the range from 1.37 ± 0.86 to 1.88 ± 1.01% 10-2mmHg-1, lower than that of native vessels. The Silkothane® small-calibre devices were also implanted in rats demonstrating to be adequate for vascular applications; all the treated rats survived the surgery for three months after implantation, and 16 rats out of 17 (94%) still showed blood flow inside the graft at sacrifice. The obtained results lay the basis for a deeper investigation of the interaction between the Silkothane® graft and the implant site, which may deal with further analysis on the potentialities in terms of degradability and tissue formation, on longer time-points.

International quantification of microplastics in indoor dust: prevalence, exposure and risk assessment.

This international scale study measured the prevalence of indoor microplastics (MPs) in deposited dust in 108 homes from 29 countries over a 1-month period. Dust borne MPs shape, colour, and length were determined using microscopy and the composition measured using µFTIR. Human health exposure and risk was assessed along with residential factors associated with MPs via a participant questionnaire. Samples were categorised according to each country's gross national income (GNI). Synthetic polymers dominated in low income (LI) (39%) and high income (HI) (46%) while natural fibres were the most prevalent in medium income (MI) (43%) countries. Composition and statistical analysis showed that the main sources of MPs and dust were predominantly from indoor sources. Across all GNI countries, greater vacuuming frequency was associated with lower MPs loading. High income country samples returned higher proportions of polyamides and polyester fibres, whereas in LI countries polyurethane was the most prominent MPs fibre. Exposure modelling showed infants (0-2 years) were exposed to the highest MPs dose through inhalation (4.5 × 10-5 ± 3 × 10-5) and ingestion (3.24 × 10-2 ± 3.14 × 10-2) mg/kg-Bw/day. Health risk analysis of constituent monomers of polymers indicates cancer incidence was estimated at 4.1-8.7 per million persons across age groups. This study's analysis showed socio-economic factors and age were dominant variables in determining dose and associated health outcomes of MPs in household dust.

Assessment of personal inhalation and skin exposures to polymeric methylene diphenyl diisocyanate during polyurethane fabric coating.

Methylene diphenyl diisocyanate (MDI) monomers and polymeric MDI (pMDI) are aromatic isocyanates widely used in the production of polyurethanes. These isocyanates can cause occupational asthma, hypersensitivity pneumonitis, as well as contact dermatitis. Skin exposure likely contributes toward initial sensitization but is challenging to monitor and quantitate. In this work, we characterized workers' personal inhalation and skin exposures to pMDI in a polyurethane fabric coating factory for subsequent health effect studies. Full-shift personal and area air samples were collected from eleven workers in representative job areas daily for 1-2 weeks. Skin exposure to hands was evaluated concomitantly with a newly developed reagent-impregnated cotton glove dosimeter. Samples were analyzed for pMDI by liquid chromatography-tandem mass spectrometry. In personal airborne samples, the concentration of 4,4'-MDI isomer, expressed as total NCO, had a geometric mean (GM) and geometric standard deviation (GSD) of 5.1 and 3.3 ng NCO/m3, respectively (range: 0.5-1862 ng NCO/m3). Other MDI isomers were found at much lower concentrations. Analysis of 4,4'-MDI in the glove dosimeters exhibited much greater exposures (GM: 10 ng/cm2) and substantial variability (GSD: 20 ng NCO/cm2; range: 0-295 ng NCO/cm2). MDI inhalation exposure was well below occupational limits for MDI for all the job areas. However, MDI skin exposure to hands was substantial. These findings demonstrated the potential for substantial isocyanate skin exposure in work settings with very low airborne levels. This exposure characterization should inform future studies that aim to assess the health effects of work exposures to MDI and the effectiveness of protective measures.