Design, clinical applications and post-surgical assessment of bioresorbable 3D-printed craniofacial composite implants.

This study details the design, fabrication, clinical trials' evaluation, and analysis after the clinical application of 3D-printed bone reconstruction implants made of nHAp@PLDLLA [nanohydroxyapatite@poly(L-lactide-co-D,L-lactide)] biomaterial. The 3D-printed formulations have been tested as bone reconstruction Cranioimplants in 3 different medical cases, including frontal lobe, mandibular bone, and cleft palate reconstructions. Replacing one of the implants after 6 months provided a unique opportunity to evaluate the post-surgical implant obtained from a human patient. This allowed us to quantify physicochemical changes and develop a spatial map of osseointegration and material degradation kinetics as a function of specific locations. To the best of our knowledge, hydrolytic degradation and variability in the physicochemical and mechanical properties of the biomimetic, 3D-printed implants have not been quantified in the literature after permanent placement in the human body. Such analysis has revealed the constantly changing properties of the implant, which should be considered to optimize the design of patient-specific bone substitutes. Moreover, it has been proven that the obtained composition can produce biomimetic, bioresorbable and bone-forming alloplastic substitutes tailored to each patient, allowing for shorter surgery times and faster patient recovery than currently available methods.

In silico assessment of the bone regeneration potential of complex porous scaffolds.

Mechanical environment plays a crucial role in regulating bone regeneration in bone defects. Assessing the mechanobiological behavior of patient-specific orthopedic scaffolds in-silico could help guide optimal scaffold designs, as well as intra- and post-operative strategies to enhance bone regeneration and improve implant longevity. Additively manufactured porous scaffolds, and specifically triply periodic minimal surfaces (TPMS), have shown promising structural properties to act as bone substitutes, yet their ability to induce mechanobiologially-driven bone regeneration has not been elucidated. The aim of this study is to i) explore the bone regeneration potential of TPMS scaffolds made of different stiffness biocompatible materials, to ii) analyze the influence of pre-seeding the scaffolds and increasing the post-operative resting period, and to iii) assess the influence of patient-specific parameters, such as age and mechanosensitivity, on outcomes. To perform this study, an in silico model of a goat tibia is used. The bone ingrowth within the scaffold pores was simulated with a mechano-driven model of bone regeneration. Results showed that the scaffold's architectural properties affect cellular diffusion and strain distribution, resulting in variations in the regenerated bone volume and distribution. The softer material improved the bone ingrowth. An initial resting period improved the bone ingrowth but not enough to reach the scaffold's core. However, this was achieved with the implantation of a pre-seeded scaffold. Physiological parameters like age and health of the patient also influence the bone regeneration outcome, though to a lesser extent than the scaffold design. This analysis demonstrates the importance of the scaffold's geometry and its material, and highlights the potential of using mechanobiological patient-specific models in the design process for bone substitutes.

An assessment of physical properties and the viability of osteoblast-like cells of cefazolin-impregnated calcium sulfate bone-void filler.

Calcium sulfate, an injectable and biodegradable bone-void filler, is widely used in orthopedic surgery. Based on clinical experience, bone-defect substitutes can also serve as vehicles for the delivery of drugs, for example, antibiotics, to prevent or to treat infections such as osteomyelitis. However, antibiotic additions change the characteristics of calcium sulfate cement. Moreover, high-dose antibiotics may also be toxic to bony tissues. Accordingly, cefazolin at varying weight ratios was added to calcium sulfate samples and characterized in vitro. The results revealed that cefazolin changed the hydration reaction and prolonged the initial setting times of calcium sulfate bone cement. For the crystalline structure identification, X-ray diffractometer revealed that cefazolin additive resulted in the decrease of peak intensity corresponding to calcium sulfate dihydrate which implying incomplete phase conversion of calcium sulfate hemihydrate. In addition, scanning electron microscope inspection exhibited cefazolin changed the morphology and size of the crystals greatly. A relatively higher amount of cefazolin additive caused a faster degradation and a lower compressive strength of calcium sulfate compared with those of uploaded samples. Furthermore, the extract of cefazolin-impregnated calcium sulfate impaired cell viability, and caused the death of osteoblast-like cells. The results of this study revealed that the cefazolin additives prolonged setting time, impaired mechanical strength, accelerated degradation, and caused cytotoxicity of the calcium sulfate bone-void filler. The aforementioned concerns should be considered during intra-operative applications.

Assessment of novel surgical procedures using decellularised muscle and bioactive ceramic: a histological analysis.

Tissue regeneration and neovascularisation in cases of major bone loss is a challenge in maxillofacial surgery. The hypothesis of the present study is that the addition of resorbable bioactive ceramic Silica Calcium Phosphate Cement (SCPC) to Declluraized Muscle Scaffold (DSM) can expedite bone formation and maturation. Two surgical defect models were created in 18 nude transgenic mice. Group 1(n = 6), with a 2-mm decortication calvarial defect, was treated with a DSM/SCPC sheet over the corticated bone as an onlay then seeded with human Mesenchymal Stromal Cells hMSC in situ. In Group 2 (n = 6), a critical size (4 mm) calvarial defect was made and grafted with DSM/SCPC/in situ human bone marrow stromal cells (hMSCs). The control groups included Group 3 (n = 3) animals, with a 2-mm decortication defect treated with an onlay DSM sheet, and Group 4 (n = 3) animals, treated with critical size defect grafted with plain DSM. After 8 weeks, bone regeneration in various groups was evaluated using histology, immunohistochemistry and histomorphometry. New bone formation and maturation was superior in groups treated with DSM/SCPC/hMSC. The DMS/SCPC scaffold has the ability to augment and induce bone regeneration and neovascularisation in cases of major bone resorption and critical size defects.

In-vitroassessment of ß-tricalcium phosphate/bredigite-ciprofloxacin (CPFX) scaffolds for bone treatment applications.

In the present study, ß-tricalcium phosphate (ß-TCP) scaffolds with various amounts of bredigite (Bre) were fabricated by the space holder method. The effect of bredigite content on the structure, mechanical properties,in vitrobioactivity, and cell viability was investigated. The structural assessment of the composite scaffolds presented interconnected pores with diameter of 300-500 µm with around 78%-82% porosity. The results indicated that the compressive strength of the scaffolds with 20% bredigite (1.91 MPa) was improved in comparison with scaffolds with 10% bredigite (0.52 MPa), due to the reduction of the average pore and grain sizes. Also, the results showed that the bioactivity and biodegradability of ß-TCP/20Bre were better than that of ß-TCP/10Bre. Besides, in this study, the release kinetics of ciprofloxacin (CPFX) loaded ß-TCP/Bre composites as well as the ability of scaffolds to function as a sustained release drug carrier was investigated. Drug release pattern of ß-TCP/bredigite-5CPFX scaffolds exhibited the rapid burst release of 43% for 3 h along with sustained release (82%) for 32 h which is favorable for bone infection treatment. Antibacterial tests revealed that the antibacterial properties of ß-TCP/bredigite scaffolds are strongly related to the CPFX concentration, wherein the scaffold containing 5% CPFX showed the most significant zone of inhibition (33 ± 0.5 mm) againstStaphylococcus aureus. The higher specific surface areas of nanostructure ß-TCP/bredigite scaffolds containing CPFX lead to an initial rapid release followed by constant drug delivery. MTT assay showed that the cell viability of ß-TCP/bredigite scaffold loading with up to 1%-3% CPFX (95 ± 2%), is greater than for scaffolds containing 5% CPFX (84 ± 2%). In Overall, it may suggested that ß-TCP/bredigite containing 1%-3% CPFX possesses great cell viability and antibacterial activity and be employed as bactericidal biomaterials and bone infection treatment.

Antibacterial alginate/nano-hydroxyapatite composites for bone tissue engineering: Assessment of their bioactivity, biocompatibility, and antibacterial activity.

Bone substitute materials based on bioceramics and polymers have evolved shifting from a passive role where they are merely accepted by the body; to an active role, where they respond to particular environmental conditions or to different types of cues generating suitable integration (osseointegration for this case) inside the host tissue. In this work, two types of composite materials based on a bioceramic (synthetic nano-hydroxyapatite, HA) and a biopolymer (sodium alginate, ALG) have been designed and assessed for promoting the bone regeneration. These materials were loaded with ciprofloxacin (CIP) for obtaining, not only a suitable material for a filling but with antibacterial properties. Therefore, their main features were studied through Fourier transformed-infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and transmission electron microscopy (TEM). Ultraviolet-Visible (UV-Vis) spectroscopy was used for obtaining the released concentrations of CIP and Zeta-potential (ζ-potential) was used for characterizing the adsorption of CIP onto nanoparticles. The release profile of this drug has been fit with the Ritger-Peppas model, used for studying the release kinetics of hydrogel-based systems. The bioactivity of these composites was also evaluated after 30 days of incubation in a simulated body fluid solution (SBF). Then, the assessment of antibacterial capability against the three main strains cause osteomyelitis was performed. Finally, the cell viability study and the cellular morphology assay were also carried out. These last assays have shown encouraging results and, gathered with their other properties, such as their bioactivity and antibacterial properties; they could lead to propose these materials as new bone filler antibiotic devices.

In vitro and in vivo assessment of CaP materials for bone regenerative therapy. The role of multinucleated giant cells/osteoclasts in bone regeneration.

In this work, bone formation/remodeling/maturation was correlated with the presence of multinucleated giant cells (MGCs)/osteoclasts (tartrate-resistant acid phosphatase [TRAP]-positive cells) on the surface of beta-tricalcium phosphate (ß-TCP), sintered deproteinized bovine bone (sDBB), and carbonated deproteinized bovine bone (cDBB) using a maxillary sinus augmentation (MSA) in a New Zealand rabbit model. Microtomographic, histomorphometric, and immunolabeling for TRAP-cells analyses were made at 15, 30, and 60 days after surgery. In all treatments, a faster bone formation/remodeling/maturation and TRAP-positive cells activity occurred in the osteotomy region of the MSA than in the middle and submucosa regions. In the ß-TCP, the granules were rapidly reabsorbed by TRAP-positive cells and replaced by bone tissue. ß-TCP enabled quick bone regeneration/remodeling and full bone and marrow restoration until 60 days, but with a significant reduction in MSA volume. In cDBB and sDBB, the quantity of TRAP-positive cells was smaller than in ß-TCP, and these cells were associated with granule surface preparation for osteoblast-mediated bone formation. After 30 days, more than 80% of granule surfaces were surrounded and integrated by bone tissue without signs of degradation, preserving the MSA volume. Overall, the materials tested in a standardized preclinical model led to different bone formation/remodeling/maturation within the same repair process influenced by different microenvironments and MGCs/osteoclasts. © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 108B:282-297, 2020.

Modeling, Assessment, and Design of Porous Cells Based on Schwartz Primitive Surface for Bone Scaffolds.

The design of bone scaffolds for tissue regeneration is a topic of great interest, which involves different issues related to geometry of architectures, mechanical behavior, and biological requirements, whose optimal combination determines the success of an implant. Additive manufacturing (AM) has widened the capability to produce structures with complex geometries, which should potentially satisfy the different requirements. These architectures can be obtained by means of refined methods and have to be assessed in terms of geometrical and mechanical properties. In this paper a triply periodic minimal surface (TPMS), the Schwarz's Primitive surface (P-surface), has been considered as scaffold unit cell and conveniently parameterized in order to investigate the effect of modulation of analytical parameters on the P-cell geometry and on its properties. Several are the cell properties, which can affect the scaffold performance. Due to the important biofunctional role that the surface curvature plays in mechanisms of cellular proliferation and differentiation, in this paper, in addition to properties considering the cell geometry in its whole (such as volume fraction or pore size), new properties were proposed. These properties involve, particularly, the evaluation of local geometrical-differential properties of the P-surface. The results of this P-cell comprehensive characterization are very useful for the design of customized bone scaffolds able to satisfy both biological and mechanical requirements. A numerical structural evaluation, by means of finite element method (FEM), was performed in order to assess the stiffness of solid P-cells as a function of the changes of the analytical parameters of outer surface and the thickness of cell. Finally, the relationship between stiffness and porosity has been analyzed, given the relevance that this property has for bone scaffolds design.

Bioactive glass added to autogenous bone graft in maxillary sinus augmentation: a prospective histomorphometric, immunohistochemical, and bone graft resorption assessment.

OBJECTIVE: The aim of this study was to compare the bone resorption rate, histomorphometry and immunohistochemical findings of bioactive glass (Biogran; Biomet, Warsaw, IN, USA) mixed with autogenous bone grafts (1:1) and autogenous bone graft isolate in maxillary sinus elevation surgery. MATERIAL AND METHODS: A total of 9 maxillary sinuses were grafted with Biogran with autogenous bone graft (group 1) and 12 were mixed with autogenous bone graft (group 2). Postoperative cone beam computed tomography (CBCT) was used to measure the initial graft volume after 15 days (T1), and 6 months later, another CBCT scan was performed to evaluate the final graft volume (T2) and determine the graft resorption rate. The resorption outcomes were 37.9%±18.9% in group 1 and 45.7%±18.5% in group 2 (P=0.82). After 6 months, biopsies were obtained concurrent with the placement of dental implants; these implants were subjected to histomorphometric analysis and immunohistochemical analysis for tartrate-resistant acid phosphatase (TRAP). RESULTS: The average bone formation in group 1 was 36.6%±12.9 in the pristine bone region, 33.2%±13.3 in the intermediate region, and 45.8%±13.8 in the apical region; in group 2, the values were 34.4%±14.4, 35.0%±13.9, and 42.0%±16.6 of new bone formation in the pristine bone, intermediate, and apical regions, respectively. Immunostaining for TRAP showed poor clastic activity in both groups, which can indicate that those were in the remodeling phase. CONCLUSIONS: The similarity between the groups in the formation and maintenance of the graft volume after 6 months suggests that the bioactive glass mixed with autogenous bone (1:1) can be used safely as a bone substitute for the maxillary sinus lift.

Bioactive glass added to autogenous bone graft in maxillary sinus augmentation: a prospective histomorphometric, immunohistochemical, and bone graft resorption assessment

Abstract Objective The aim of this study was to compare the bone resorption rate, histomorphometry and immunohistochemical findings of bioactive glass (Biogran; Biomet, Warsaw, IN, USA) mixed with autogenous bone grafts (1:1) and autogenous bone graft isolate in maxillary sinus elevation surgery. Material and Methods A total of 9 maxillary sinuses were grafted with Biogran with autogenous bone graft (group 1) and 12 were mixed with autogenous bone graft (group 2). Postoperative cone beam computed tomography (CBCT) was used to measure the initial graft volume after 15 days (T1), and 6 months later, another CBCT scan was performed to evaluate the final graft volume (T2) and determine the graft resorption rate. The resorption outcomes were 37.9%±18.9% in group 1 and 45.7%±18.5% in group 2 (P=0.82). After 6 months, biopsies were obtained concurrent with the placement of dental implants; these implants were subjected to histomorphometric analysis and immunohistochemical analysis for tartrate-resistant acid phosphatase (TRAP). Results The average bone formation in group 1 was 36.6%±12.9 in the pristine bone region, 33.2%±13.3 in the intermediate region, and 45.8%±13.8 in the apical region; in group 2, the values were 34.4%±14.4, 35.0%±13.9, and 42.0%±16.6 of new bone formation in the pristine bone, intermediate, and apical regions, respectively. Immunostaining for TRAP showed poor clastic activity in both groups, which can indicate that those were in the remodeling phase. Conclusions The similarity between the groups in the formation and maintenance of the graft volume after 6 months suggests that the bioactive glass mixed with autogenous bone (1:1) can be used safely as a bone substitute for the maxillary sinus lift.

Assessment of polycaprolacton (PCL) nanocomposite scaffold compared with hydroxyapatite (HA) on healing of segmental femur bone defect in rabbits.

Segmental bone loss due to trauma, infection, and tumor resection and even non-union results in the vast demand for replacement and restoration of the function of the lost bone. The objective of this study is to utilize novel inorganic-organic nanocomposites for biomedical applications. Biodegradable implants have shown great promise for the repair of bone defects and have been commonly used as bone substitutes, which traditionally would be treated using metallic implants. In this study, 45 mature male New Zealand white rabbits 6-8 months and weighting 3-3.5 kg were examined. Rabbits were divided into three groups. Surgical procedures were done after an intramuscular injection of Ketamine 10% (ketamine hydrochloride, 50 mg/kg), Rompun 5% (xylazine, 5 mg/kg). Then an approximately 6 mm diameter - 5 mm cylinder bone defect was created in the femur of one of the hind limbs. After inducing the surgical wound, all rabbits were colored and randomly divided into three experimental groups of nine animals each: Group 1 received medical pure nanocomposite polycaprolactone (PCL) granules, Group 2 received hydroxyapatite and Group 3 was a control group with no treatment. Histopathological evaluation was performed on days 15, 30 and 45 after surgery. On day 45 after surgery, the quantity of newly formed lamellar bone in the healing site in PCL group was better than onward compared with HA and control groups. Finally, nanocomposite PCL granules exhibited a reproducible bone-healing potential.

A novel one-pot process for near-net-shape fabrication of open-porous resorbable hydroxyapatite/protein composites and in vivo assessment.

We present a mild one-pot freeze gelation process for fabricating near-net, complex-shaped hydroxyapatite scaffolds and to directly incorporate active proteins during scaffold processing. In particular, the direct protein incorporation enables a simultaneous adjustment and control of scaffold microstructure, porosity, resorbability and enhancement of initial mechanical and handling stability. Two proteins, serum albumin and lysozyme, are selected and their effect on scaffold stability and microstructure investigated by biaxial strength tests, electron microscopy, and mercury intrusion porosimetry. The resulting hydroxyapatite/protein composites feature adjustable porosities from 50% to 70% and a mechanical strength ranging from 2 to 6 MPa comparable to that of human spongiosa without any sintering step. Scaffold degradation behaviour and protein release are assessed by in vitro studies. A preliminary in vivo assessment of scaffold biocompatibility and resorption behaviour in adult domestic pigs is discussed. After implantation, composites were resorbed up to 50% after only 4 weeks and up to 65% after 8 weeks. In addition, 14% new bone formation after 4 weeks and 37% after 8 weeks were detected. All these investigations demonstrate the outstanding suitability of the one-pot-process to create, in a customisable and reliable way, biocompatible scaffolds with sufficient mechanical strength for handling and surgical insertion, and for potential use as biodegradable bone substitutes and versatile platform for local drug delivery.

In vitro and in vivo bioactivity assessment of a polylactic acid/hydroxyapatite composite for bone regeneration.

Synthetic bone graft substitutes based on composites consisting of a polymer and a calcium-phosphate (CaP) ceramic are developed with the aim to satisfy both mechanical and bioactivity requirements for successful bone regeneration. In the present study, we have employed extrusion to produce a composite consisting of 50 wt.% poly(D,L-lactic acid) (PLA) and 50 wt.% nano-sized hydroxyapatite (HA) powder, achieving homogeneous distribution of the ceramic within the polymeric phase. In vitro, in both a simulated physiological saline (SPS) and a simulated body fluid (SBF), a greater weight loss was observed for PLA/HA than for PLA particles upon 12-week immersion. Furthermore, in SPS, a continuous release of calcium and phosphate from the composite was measured, whereas in SBF, decrease of the amount of the two ions in the solution was observed both for PLA and PLA/HA accompanied with the formation of a CaP layer on the surface. In vitro characterization of the composite bioactivity was performed by culturing human mesenchymal stromal cells (hMSCs) and assessing proliferation and osteogenic differentiation, with PLA as a control. Both PLA/HA composite and PLA control were shown to support hMSCs proliferation over a period of two weeks. In addition, the composite significantly enhanced alkaline phosphatase (ALP) activity of hMSCs in osteogenic medium as compared with the polymer control. A novel implant design was employed to develop implants from dense, extruded materials, suitable for testing osteoinductivity in vivo. In a preliminary study in dogs, PLA/HA composite implants induced heterotopic bone formation upon 12-week intramuscular implantation in all animals, in contrast to PLA control, which was not osteoinductive. Unlike in vitro, a more pronounced degradation of PLA was observed in vivo as compared with PLA/HA composite.

[Experimental assessment of biodegradable polyglycolic and polylactic acid polymers for medical use].

Interrelations of biodegradable poliglicolic and polilactic acid polymers in various proportions implanted in standardized bone defects were evaluated in animal model with 40 Wister line rats. During 10 month follow-up period bone capsule surrounded all implants, but timing of bone formation and bone quality varied significantly being optimal in LactoSorb group. Destructive features of polymers were also seen in implant-bone contact area defined as inflammation, fibrous tissue formation and cell dystrophy.

Mechanical stability and clinical applicability assessment of novel orthodontic mini-implant design.

OBJECTIVE: To compare the stability and clinical applicability of a novel orthodontic mini-implant design (N2) with the most widely used commercially available (CA) design. MATERIALS AND METHODS: Two groups of mini-implants were tested: a CA design (1.5-mm diameter, 6-mm length) and N2 (3-mm diameter, 2-mm length, tapered shape). Implants were inserted in bone blocks of cortical bone simulation with varying densities (20 pounds per cubic foot [pcf], 30 pcf, and 40 pcf). A torque test was used to measure maximum insertion torque (MIT) and maximum removal torque (MRT). Compression and tension force vectors were applied at angles of 10°, 20°, 30°, and 40° using customized load pins to determine primary stability. RESULTS: Mean MIT and MRT were higher in the N2 than the CA design at all three cortical bone densities except MRT in 20 pcf bone (not statistically significant). The mean compression force required to displace the N2 at all distances and angulations was greater for the N2 than the CA design. At all displacement distances, the highest mean tension force required for N2 displacement was at 10° angulation, whereas at 30° and 40°, the mean tension force required to displace the CA design was greater. CONCLUSIONS: The primary stability of the N2 is superior to that of the CA design and is promising for both orthodontic and orthopedic clinical applicability, especially under compression force. The short length of the N2 reduces risk of damage to anatomic structures and root proximity during placement and orthodontic treatment. The stability of the N2 may be compromised in areas of high bone density and highly angulated tension force.

Mechanical characterization of injection-molded macro porous bioceramic bone scaffolds.

Bioactive ceramic materials like tricalcium phosphate (TCP) have been emerging as viable material alternatives to the current therapies of bone scaffolding to target fracture healing and osteoporosis. Both material and architectural characteristics play a critical role in the osteoconductive capacity and strength of bone scaffolds. Thus, the objective of this research was to investigate the sintering temperature effect of a cost-effective manufacturing process on the architecture and mechanical properties of a controlled macro porous bioceramic bone scaffold. In this study the physical and mechanical properties of ß-TCP bioceramic scaffolds were investigated as a function of the sintering temperature in the range of 950-1150 °C. Physical properties investigated included bulk dimensions, pore size, and strut thickness; and, compressive mechanical properties were evaluated in air at room temperature and in saline solution at body temperature. Statistically significant increases in apparent elastic modulus were measured for scaffolds sintered at higher temperatures. Structural stiffness for all the specimens was significantly reduced when tested at body temperature in saline solution. These findings support the development of clinically successful bioceramic scaffolds that may stimulate bone regeneration and scaffold integration while providing structural integrity.

In vivo assessment of bone ingrowth potential of three-dimensional e-beam produced implant surfaces and the effect of additional treatment by acid etching and hydroxyapatite coating.

The bone ingrowth potential of three-dimensional E-beam-produced implant surfaces was examined by histology and compared to a porous plasma-sprayed control. The effects of acid etching and a hydroxyapatite (HA) coating were also evaluated by histology. Specimens were implanted in the distal femur of 10 goats. Histological analysis of bone ingrowth was performed 6 weeks after implantation. The E-beam-produced surfaces showed significantly better bone ingrowth compared to the plasma-sprayed control. Additional treatment of the E-beam surface structures with a HA coating, further improved bone ingrowth potential of these structures significantly. Acid etching of the E-beam structures did not influence bone ingrowth significantly. In conclusion, the HA-coated, E-beam-produced structures are promising potential implant surfaces.

Biodegradable polycaprolactone-chitosan three-dimensional scaffolds fabricated by melt stretching and multilayer deposition for bone tissue engineering: assessment of the physical properties and cellular response.

Fabrication of polycaprolactone (PCL)-chitosan (CS) three-dimensional (3D) scaffolds using the novel technique of melt stretching and multilayer deposition was introduced. In brief, firstly, the PCL-CS monofilaments containing 0% (pure PCL), 10%, 20% and 30% CS by weight were fabricated by melting and stretching processes. Secondly, the desired multilayer (3D) scaffolds were fabricated by arranging and depositing the filaments. Physical properties of the filaments and the scaffolds were evaluated. MC3T3-E1 cell lines were seeded on the scaffolds to assess their proliferation. A typical micro-groove pattern was found on the surfaces of pure PCL filaments due to stretching. The filaments of PCL-30%CS had the highest tendency of fracture during stretching and could not be used to form the scaffold. Increasing CS proportions tended to reduce the micro-groove pattern, surface roughness, tensile strength and elasticity of the filaments, whilst compressive strength of the PCL-CS scaffolds was not affected. The average pore size and porosity of the scaffolds were 536.90 ± 17.91 µm and 45.99 ± 2.8% respectively. Over 60 days, degradation of the scaffolds gradually increased (p > 0.05). The more CS containing scaffolds were found to increase in water uptake, but decrease in degradation rate. During the culture period, the growth of the cells in PCL-CS groups was significantly higher than in the pure PCL group (p < 0.05). On culture-day 21, the growth in the PCL-20%CS group was significantly higher than the other groups (p < 0.05). In conclusion, the PCL-20%CS scaffolds obtained the optimum results in terms of physical properties and cellular response.

Mechanical stability in a human radius fracture treated with a novel tissue-engineered bone substitute: a non-invasive, longitudinal assessment using high-resolution pQCT in combination with finite element analysis.

The clinical gold standard in orthopaedics for treating fractures with large bone defects is still the use of autologous, cancellous bone autografts. While this material provides a strong healing response, the use of autografts is often associated with additional morbidity. Therefore, there is a demand for off-the-shelf biomaterials that perform similar to autografts. Biomechanical assessment of such a biomaterial in vivo has so far been limited. Recently, the development of high-resolution peripheral quantitative computed tomography (HR-pQCT) has made it possible to measure bone structure in humans in great detail. Finite element analysis (FEA) has been used to accurately estimate bone mechanical function from three-dimensional CT images. The aim of this study was therefore to determine the feasibility of these two methods in combination, to quantify bone healing in a clinical case with a fracture at the distal radius which was treated with a new bone graft substitute. Validation was sought through a conceptional ovine model. The bones were scanned using HR-pQCT and subsequently biomechanically tested. FEA-derived stiffness was validated relative to the experimental data. The developed processing methods were then adapted and applied to in vivo follow-up data of the patient. Our analyses indicated an 18% increase of bone stiffness within 2 months. To our knowledge, this was the first time that microstructural finite element analyses have been performed on bone-implant constructs in a clinical setting. From this clinical case study, we conclude that HR-pQCT-based micro-finite element analyses show high potential to quantify bone healing in patients.

Quantitative assessment of growth factors in reaming aspirate, iliac crest, and platelet preparation.

Large bony defects and non-unions are still a complication in trauma and orthopedic surgery. Treatment strategies include the use of autogenous materials (iliac crest), allogenic bone, bone substitutes, and currently stimulation with growth factors such as BMP-2, BMP-7 or the growth factors containing platelet-rich plasma (PRP). Another source of bone graft material might be the cuttings produced during intramedullary reaming. The aim of this study was to compare the quantity of various growth factors found within iliac crest, bony reaming debris, reaming irrigation fluid, and platelet-rich plasma. Iliac crest and reaming debris and irrigation samples were harvested during surgery. PRP was prepared from blood. The growth factors in the bony materials (iliac crest or reaming debris) and of the liquid materials (platelet-poor plasma (PPP), platelet-rich plasma (PRP) or reaming irrigation) were compared. Elevated levels of FGFa, PDGF, IGF-I, TGF-beta1 and BMP-2 were measured in the reaming debris as compared to iliac crest curettings. However, VEGF and FGFb were significantly lower in the reaming debris than from iliac crest samples. In comparing PRP and PPP all detectable growth factors, except IGF-I, were enhanced in the platelet-rich plasma. In the reaming irrigation FGFa (no measurable value in the PRP) and FGFb were higher, but VEGF, PDGF, IGF-I, TGF-beta1 and BMP-2 were lower compared to PRP. BMP-4 was not measurable in any sample. The bony reaming debris is a rich source of growth factors with a content comparable to that from iliac crest. The irrigation fluid from the reaming also contains growth factors.