Simulated Wound Assessment Using Digital Planimetry versus Three-Dimensional Cameras: Implications for Clinical Assessment.

BACKGROUND: Clinical management of wounds can benefit from objective measures of response to treatment. Wound surface area and volume are objective measures of wound healing. Using a synthetic wound model, we compare the accuracy and reproducibility of 2 commercially available 3-dimensional (3D) cameras against planimetry and water displacement. METHODS: Twelve ulcers of various sizes and colors were reproduced in modeling clay and cured. Five naive observers used digital planimetry, water displacement, Eykona camera (Fuel 3D, UK), and Silhouette camera (ARANZ, New Zealand) to measure the wounds. RESULTS: When compared with traditional planimetry, wound surface area measurement with Eykona and Silhouette tended to underestimate wounds by 1.7% and 3.7%, respectively. Spearman correlation coefficients were 0.94 (Eykona) and 0.92 (Silhouette). Intraclass correlations for planimetry and the 2 cameras were all 1. Eykona and Silhouette tended to underestimate wound volumes when compared with water displacement by 58% and 23%, respectively. Spearman correlation coefficients were 0.92 (Eykona) and 0.72 (Silhouette). Intraclass correlations for water displacement and the two cameras were all 1. DISCUSSION: Serial accurate objective area measurements are feasible as part of ongoing clinical assessment of wounds. 3D cameras are reliable but have not shown superior accuracy to manual planimetry, and financial concerns and IT integration may limit general clinical usage. Volume measurements of wounds are practicable as part of clinical care.

In vivo scanning electron microscope assessment of enamel permeability in primary teeth with and without early childhood caries.

BACKGROUND: Over the years, certain primary teeth have been shown to be highly sensitive to dental caries, while others have remained caries-free. It has been hypothesized that this may be attributed to differences in the permeability of the enamel surface. AIM: The aim of the study was to evaluate the hypothesized differences in the permeability of primary tooth enamel in children with and those without Severe Early Childhood Caries (S-ECC) using scanning electron microscopy. MATERIALS AND METHODS: Sixteen children between 3 and 6 years of age were randomly selected and divided into two groups: Group 1, children without S-ECC (n = 8), and Group 2, children with S-ECC (n = 8). In each child, 4 teeth (the maxillary right and left central and lateral incisors) were subjected to evaluation. An impression was made with polyvinylsiloxane impression material, and scanning electron microscopy was used to inspect the negative replicas for droplets. RESULTS: The results indicated higher significance when individual regions (cervical, middle, and incisal thirds) in the two groups were evaluated and compared. Similarly, the overall results showed high statistical significance between S-ECC and non-S-ECC teeth. CONCLUSION: There could be a positive relationship between the permeability of tooth enamel and the development of caries, which needs further research.

Assessment of growth dynamics of human cranium middle fossa in foetal period.

BACKGROUND: Available literature analysis demonstrated smallness of studies of cranial base. OBJECTIVES: The goal of the study was to analyse the medial fossa of the human cranium in the foetal period against other fossae. MATERIAL AND METHODS: Survey material consisted of 110 human foetuses at a morphological age of 16-28 weeks of foetal life, CRL 98-220 mm. Anthropological, preparation method, reverse method and statistical analysis were utilized. The survey incorporated the following computer programmes: Renishaw, TraceSurf, AutoCAD, CATIA. The reverse method seems especially interesting (impression with polysiloxane (silicone elastomer of high adhesive power used in dentistry) with 18 D 4823 activator. Elicited impression accurately reflected complex shape of cranium base. RESULTS: On assessing the relative rate of cranium medial fossa, the rate was found to be stable (linear model) for the whole of the analysed period and is 0.19%/week, which stands for the gradual and steady growth of the middle fossa in relation to the whole of the cranium base. At the same time, from the 16th till 28th week of foetal life, relative volume of the cranium middle fossa increases more intensively than cranium anterior fossa, whereas the cranium middle fossa volume as compared with the cranium posterior fossa is definitely slower. In the analysed period, the growth rate of the cranium base middle fossa was bigger in the 4th and 5th weeks than in the 6th and 7th weeks of foetal life. The investigations revealed cranium base asymmetry of the left side. Furthermore, the anterior fossae volume on the left side is significantly bigger than the one of the fossae on the right side. CONCLUSIONS: Volume growth rate is more intensive in the 4th and 5th than in the 6th and 7th weeks of foetal life. In the examined period, the relative growth rate of cranium base middle fossa is 0.19%/week and it is stable - linear model. The study revealed correlations in the form of mathematical models, which enabled foetuses age assessment.

Rapid prototyping of compliant human aortic roots for assessment of valved stents.

Adequate in-vitro training in valved stents deployment as well as testing of the latter devices requires compliant real-size models of the human aortic root. The casting methods utilized up to now are multi-step, time consuming and complicated. We pursued a goal of building a flexible 3D model in a single-step procedure. We created a precise 3D CAD model of a human aortic root using previously published anatomical and geometrical data and printed it using a novel rapid prototyping system developed by the Fab@Home project. As a material for 3D fabrication we used common house-hold silicone and afterwards dip-coated several models with dispersion silicone one or two times. To assess the production precision we compared the size of the final product with the CAD model. Compliance of the models was measured and compared with native porcine aortic root. Total fabrication time was 3 h and 20 min. Dip-coating one or two times with dispersion silicone if applied took one or two extra days, respectively. The error in dimensions of non-coated aortic root model compared to the CAD design was <3.0% along X, Y-axes and 4.1% along Z-axis. Compliance of a non-coated model as judged by the changes of radius values in the radial direction by 16.39% is significantly different (P<0.001) from native aortic tissue--23.54% at the pressure of 80-100 mmHg. Rapid prototyping of compliant, life-size anatomical models with the Fab@Home 3D printer is feasible--it is very quick compared to previous casting methods.

A qualitative assessment of non-carious cervical lesions in extracted human teeth.

BACKGROUND: Opinions vary about the causes of non-carious cervical lesions (NCCLs). They have been attributed to toothbrush abrasion, acid corrosion (commonly termed dental erosion), and abfraction. The purpose of this study was to examine the microwear details of NCCLs in a collection of extracted human teeth using scanning election microscopy (SEM). METHODS: Negative replicas of large NCCLs in 24 extracted human teeth were obtained in polyvinylsiloxane impression material (Light Body Imprint II, 3M ESPE) and viewed under SEM. RESULTS: All NCCLs extended from the cemento-enamel junction to the root surface and they displayed a variety of wedge-shaped appearances. There was evidence of both abrasion and corrosion in 18 of the 24 teeth (75.0 per cent), abrasion only in one tooth (4.2 per cent) and corrosion only in five teeth (20.8 per cent). Horizontal furrows with smooth edges and minor scratch marks, characteristic of abrasion and corrosion, were noted in 13 teeth (54.2 per cent). CONCLUSIONS: Based on microscopic assessment of a sample of extracted teeth, it appears that abrasion and corrosion are common associated aetiological factors in the formation of NCCLs.

An objective assessment of botulinum toxin A effect on superficial skin texture.

The botulinum toxin A (BTX-A) role on elimination of hyperkinetic wrinkles is consolidated, although relying on subjective methods of assessment. A prospective open-label study was performed on 10 patients to objectively analyze superficial skin texture changes caused by BTX-A in the glabellar area. Skin areas were reproduced by silicon replica technique at baseline, 1 month, and 6 months after treatment. Takahashi's parameters (roughness, anisotropy, microsulcus number, and width) were obtained from scanning electron microscopy (SEM) analysis and compared using the Wilcoxon signed rank test. SEM images showed skin texture changes, and software analysis gave parameters for statistical analysis, allowing an objective evaluation. Statistically significant parameter modifications were evidenced. BTX-A effectiveness in wrinkle treatment was confirmed, and no differences in skin texture parameters from baseline to toxin action end were noted.

Técnica de replicação de amostras em positivo. Análise no Microscópio Eletrônico de Varredura / Positive replication tehcnique. Scanning Electron Microscope Assessment

A Microscopia Eletrônica de Varredura apresenta algumas desvantagens como a formação de trincas ou contração do dente durante seu preparo, assim como a impossibilidade de realizar observações in vivo. Para diminuir estes problemas, têm-se desenvolvido técnicas de replicação, avaliando a cópia e não o dente, o que permite estudar processos e seqüências de tratamento na mesma amostra, tanto in vitro como in vivo. Dessa forma, a proposição deste trabalho é avaliar morfologicamente a fidelidade de uma técnica de replicação, utilizando 2 resinas epóxicas e uma técnica de moldagem em dentes humanos extraídos. Uma vez eliminado o cemento no terço cervical radicular dos dentes com alta rotação, delimitou-se uma área de 4X4 na qual foi aplicado EDTA-T 24% por 3 minutos, seguindo da lavagem com soro e secagem com jato de ar, expondo túbulos dentinários. Estes seguimentos foram moldados, utilizando silicona de adição Aquasil (pesada e leve). Posteriormente, as moldagens foram vazadas com as resinas CMR 028-endurecedor CME-251 (Polipox, São Paulo) e o Epoxiglass 1504 e endurecedor 1603 (Epoxiglass-SP). Todas as réplicas e dentes naturais foram avaliados no MEV tomando fotomicrografias que foram avaliadas de acordo com o grau de fidelidade na réplica dos túbulos dentinários. Os resultados mostraram que a técnica de replicação reproduziu satisfatoriamente as características da superfície dentária.

CT angiography in the assessment of carotid atherosclerotic disease: results of more than two years' experience.

PURPOSE: To assess the role of CT Angiography (CTA) in patients with carotid atherosclerotic disease as compared to echo-colour Doppler (CDUS) ultrasound of the supra-aortic trunks (SAT) and surgery. MATERIALS AND METHODS: Eighty-two patients with suspected carotid atherosclerotic disease were submitted to CDUS and CTA of the supra-aortic trunks. Agreement between CDUS and CTA was first evaluated with regard to the following parameters: degree of stenosis according to NASCET criteria, plaque morphology, presence of ulcerations, tandem lesions and vessel abnormalities. Secondly, data provided by the two methodologies were compared with the surgical specimens (35 patients); in 12 cases, the stenosis was measured on the cast of the carotid plaque made of for biologic use silicone. RESULTS: The correlation between CDUS and CTA in evaluating the degree of stenosis was 75.6%; poor agreement was found for mild (61.1%) and severe (69.1%) stenoses; agreement in the evaluation of vessel abnormalities, plaque morphology and ulcerations was 81.7%, 89.0% and 96.3%, respectively. CTA demonstrated 11 tandem lesions not detected CDUS. Compared to surgery, CTA correctly classified the degree of stenosis according to NASCET criteria in 31/35 cases (88.6%) - as opposed to 29/35 by CDUS (82.9%) - and never overestimated the stenosis. CTA proved superior to CDUS in detecting plaque ulcerations (75% vs 25% sensitivity) and vessel abnormalities (100% vs 44.4% sensitivity). CONCLUSIONS: CTA is recommended as a second-level examination in patients with carotid atherosclerotic steno-obstructive disease who are surgical candidates.

Digital assessment of occlusal wear patterns on occlusal stabilization splints: a pilot study.

STATEMENT OF PROBLEM: If masticatory load distribution is task-dependent, then the pattern of wear on an acrylic resin occlusal splint over time may affect clinical outcome. PURPOSE: This pilot study quantitatively assessed posterior wear after 3 months on the occlusal surfaces of maxillary stabilization splints. MATERIAL AND METHODS: Subjects with known history of nocturnal bruxism were given heat-cured full-arch acrylic resin occlusal stabilization splints to be worn nocturnally for 3 months. Splint occlusion was adjusted at appliance delivery and was refined at the baseline session 1 to 2 weeks later. No further adjustment of the splint surface was performed during the 3-month study period. Sequential impressions of the splint occlusal surface provided epoxy resin models that were digitized and analyzed through specialized software. Changes in the digitized splint surface from baseline to 3 months allowed comparison of wear facets between splint sides and among tooth locations. RESULTS: Splint wear was asymmetric between sides and uneven between dental locations. CONCLUSIONS: For full coverage occlusal splints, the appliance wear phenomenon can be site specific and, if left undisturbed, may yield two extremes of high wear and a zone of low wear in-between.

Amalgam marginal quality assessment: a comparison of seven methods.

Black's class I classic cavities were cut in 120 sound extracted human premolars and restored with one of two silver amalgams, six different base combinations, with or without cavity varnish and then aged for 3 months or 1 year. Thereafter, the restored teeth were subjected to a bacterial or acid broth in vitro carious challenge for 36 days. Resin cast impressions were made of the restoration margin of each specimen before and after the carious challenge giving a total of 240 replicas. The replicas were examined in a scanning electron microscope (SEM) and the margins subjected to seven marginal assessment procedures: (i) ranking using micrographs of the margin; (ii) percentage length of marginal discrepancy; (iii) Mjor assessment using six groups; (iv) number of margin segments showing a discrepancy; (v) greatest gap size; (vi) ranking based firstly on gap size and then number of margin segments showing a discrepancy; and (vii) ranking based firstly on gap size and then percentage length of marginal discrepancy. The data from procedures (i), (ii), (vi) and (vii) were examined using one-way ANOVA; a linear logistic statistical analysis examined data from procedures (iii)-(v). Statistical significance was chosen at P < 0.05. It was found that procedure (vii) was able to discriminate between variables to a greater degree than all other procedures. It is recommended that a ranking system based on greatest gap size and percentage length of marginal discrepancy be used to assess marginal quality of amalgam restorations.

Use of a replica-plate assay for the rapid assessment of salivary protein-bacteria interactions.

A replica-plate assay was used to screen for the interaction of salivary molecules with dental plaque bacteria. Bacterial colonies cultured from supragingival plaque on sheep-blood (SB) agar were replica-plated onto nitrocellulose membranes overlaying SB or mitis-salivarius agar. Membranes with attached colonies were removed and incubated with 125I-amylase or 125I-proline-rich glycoprotein (PRG). Positive interactions were detected by autoradiography. Only strains of Streptococcus gordonii and Actinomyces viscosus bound amylase, and strains of A. viscosus bound PRG. The results suggest that amylase and PRG bind to selected species of aerobic dental plaque bacteria.