ABSTRACT
The estuary is an energetic area connecting the inland, river, and ocean. The migration of microplastics (MPs) in this highly complex area is tied to the entire ecosystem. In this study, the effects of cohesive SPM (clay) and noncohesive SPM (sand) on the vertical migration of positively buoyant MPs, polyethylene (PE), and negatively buoyant MPs, polytetrafluoroethylene (PTFE), in the estuarine environment under hydrodynamic disturbances were investigated. The settling of positively buoyant MPs was more reliant on the cohesive SPM compared to the settling of negatively buoyant MPs. Moreover, MPs interacting with the SPM mixture at a clay-to-sand ratio of 1:9 settled more efficiently than those interacting with clay alone. A significant positive correlation was observed between MP settling percentage and the salinity level. MP settling percentage was significantly negatively correlated with fluid shear stress for both types of MPs, meanwhile, negatively buoyant MPs were able to resist greater hydraulic disturbances. In the low-energy mixing state, for both types of MPs, the settling percentage reached about 50% in only 10 min. The resuspension process of MPs under hydrodynamic disturbances was also uncovered. Additionally, the migration and potential sites of MPs were described in the context of prevalent environmental phenomena in estuaries.
Subject(s)
Particulate Matter , Water Pollutants, Chemical , Particulate Matter/analysis , Microplastics , Plastics , Salinity , Sand , Hydrodynamics , Clay , Ecosystem , Water Pollutants, Chemical/analysis , Environmental Monitoring , EstuariesABSTRACT
Ice can serve as a significant temporary repository and conveyance mechanism for microplastics (MPs). MPs present in the water column can become entrapped within developing ice formations, subsequently being sequestered and transported by ice floes. With changing temperatures, MPs stored in ice can be released back into the environment, while freezing conditions can alter the properties of MPs, ultimately affecting the fate of MPs in the environment. Freezing of MPs in freshwater ice results in the aggregation of MP particles due to physical compression, leading to an increase in particle size once the MPs are released from the ice. The freezing-induced aggregation enhances buoyancy effects, accelerating the settling/rising velocity of MPs in water. Additionally, freezing can lead to enhanced surface wetting alterations, thus improving the dispersion of hydrophobic MPs. The presence of salt in the water can mitigate the effect of freezing on MPs due to the formation of a brine network within the ice structure, which reduces the pressure on MPs entrapped by ice. In cold regions, numerous MPs undergo freezing and thawing, re-entering the water column.
ABSTRACT
Microplastics (MPs) pollution is an emerging environmental health concern, impacting soil, plants, animals, and humans through their entry into the food chain via bioaccumulation. Human activities such as improper solid waste dumping are significant sources that ultimately transport MPs into the water bodies of the coastal areas. Moreover, there is a complex interplay between the coastal climate dynamics, environmental factors, the burgeoning issue of MPs pollution and the complex web of coastal pollution. We embark on a comprehensive journey, synthesizing the latest research across multiple disciplines to provide a holistic understanding of how these inter-connected factors shape and reshape the coastal ecosystems. The comprehensive review also explores the impact of the current climatic patterns on coastal regions, the intricate pathways through which MPs can infiltrate marine environments, and the cascading effects of coastal pollution on ecosystems and human societies in terms of health and socio-economic impacts in coastal regions. The novelty of this review concludes the changes in climate patterns have crucial effects on coastal regions, proceeding MPs as more prevalent, deteriorating coastal ecosystems, and hastening the transfer of MPs. The continuous rising sea levels, ocean acidification, and strong storms result in habitat loss, decline in biodiversity, and economic repercussion. Feedback mechanisms intensify pollution effects, underlying the urgent demand for environmental conservation contribution. In addition, the complex interaction between human, industry, and biodiversity demanding cutting edge strategies, innovative approaches such as remote sensing with artificial intelligence for monitoring, biobased remediation techniques, global cooperation in governance, policies to lessen the negative socioeconomic and environmental effects of coastal pollution.
Subject(s)
Climate Change , Ecosystem , Microplastics , Microplastics/analysis , Water Pollutants, Chemical/analysis , Environmental Monitoring , Humans , Environmental Pollution/analysis , ClimateABSTRACT
The presence of plastic fragments in the environment is a growing global concern. In this study, we explored the effects of dynamic fluctuations of capillary fringe on the transport of microplastics (MPs) in the substrate combining various environmental and MP properties. Both experimental and Hydrus-2D modeling results confirmed that increasing cycles of water table fluctuation led to the rise of capillary fringe. An increase in the cycles of water table fluctuations did not significantly change the overall MP retention percentages in 0.5 mm substrate but altered the MP distribution along the column. In 1 and 2 mm substrate, the increase in cycle numbers enhanced the MP transport from substrate to the water below. In terms of the size of the MPs, more 20-25 µm polyethylene (PE2) were retained in the substrate compared to 4-6 µm polyethylene (PE1) under the same number of fluctuation cycles. High-density polytetrafluoroethylene (PTFE, 5-6 µm) exhibited higher retention percentages compared to PE1 particles. Ultraviolet aging for 60 days enhanced PE1 transport along the column, while 60 days of seawater aging did not affect PE1 transport greatly. For PTFE, ultraviolet and seawater aging enhanced its retention in the substrate. The retention percentages of both PE1 and PTFE in the column increased with the elevated ionic strength and the decrease of fluctuation velocity. This work highlights that capillary fringe fluctuation can serve as a pathway to relocate MPs to the tidal aquifer.
Subject(s)
Groundwater , Water Pollutants, Chemical , Microplastics , Plastics/chemistry , Water Pollutants, Chemical/analysis , Polytetrafluoroethylene , Polyethylene , Environmental MonitoringABSTRACT
Sea ice can serve as a temporary sink for microplastics (MPs), and thus, it too can function as a secondary source of and transport medium for MPs. This study aimed to explore the effect of various MP properties and environmental characteristics on the entrainment and enrichment of MPs in ice under varying turbulence conditions. It was found that high rotation speed in freshwater distinctively enhanced the entrainment of hydrophobic MPs in ice, this being attributable to the combined effects of frazil ice and air bubbles. The hydrophobic nature of these MPs caused them to be attracted to the water/air or water/ice interface. However, in saline water, high turbulence inhibited the entrainment of all of the MP types under study. The ice crystals formed a loose structure in saline water instead of congealing, and this allowed the exchange of MPs between ice and water, leading to the rapid expulsion of MPs from the ice. The enrichment factors of all the MPs under study increased in calm saline water compared to in calm freshwater. The results revealed that the entrainment and enrichment of MPs in ice can be critical pathways affecting their fate in cold regions.
Subject(s)
Microplastics , Water Pollutants, Chemical , Plastics , Water Pollutants, Chemical/analysis , Environmental Monitoring , Fresh WaterABSTRACT
The increasing enrichment of microplastics (MPs) in the shoreline environment poses both ecological and social-economic risks. The alteration and motion of MPs in the ocean under the effect of bulk nanobubbles (NBs) have been less extensively studied. In this study, we explored the behavior and movement of various MPs in the presence of bulk NBs. The role of salinity and external energy in the interactions between NBs and MPs was evaluated, and the mechanism underlying these interactions was analyzed. In the presence of NBs, the binding of MPs and NBs resulted in an increase in the measured average particle size and concentration. Meanwhile, NBs reduced the aggregation between MPs, while the NBs present combined with MPs to make them more stable in suspensions. The velocity of motion of MPs driven by NBs varies under different salinity conditions. The increase in ionic strength reduced the energy barrier between particles and promoted their aggregation. Thus, the binding of NBs and MPs became more stable, which in turn affected the movement of MPs in suspensions. Polyethylene (PE1) with small particle size was mainly affected by Brownian motion, and its rising was limited; therefore, polyethylene (PE2) with large particle size rose faster than PE1 in suspension, especially in the presence of NBs. The rising velocity of poly(tetrafluoroethylene) (PTFE) was higher than that of PE1 and PE2. However, when NBs were present, the trend of the change in velocity was the opposite compared to the absence of NBs for PTFE. Moreover, various types of MPs were found to be affected distinctly by external energy. The presence of NBs had a clear effect on PE under shaking conditions, whereas the effect on PTFE was less obvious.
Subject(s)
Microplastics , Water Pollutants, Chemical , Plastics , Suspensions , Polyethylene , Oceans and Seas , PolytetrafluoroethyleneABSTRACT
Reducing greenhouse gas emissions from maritime transport is an urgent topic. Some regional emissions trading systems (ETSs), buoyed by the globalized market-based measures (MBMs) plan of the International maritime organization, have initially assessed the feasibility of including maritime emissions under compliance obligations. However, including maritime emissions (which are interjurisdictional) in the existing ETSs is controversial, and globalized maritime MBMs remain elusive. Therefore, this study designed a joint bilateral maritime carbon market (BMCM) model based on the European ETS (EU-ETS) and Quebec ETS (QC-ETS). The carbon costs, speed optimization, and marginal abatement costs of three container routes under BMCM were analyzed. The results show that this Euro-American linkage achieves adequate emission coverage on specific routes and generates acceptable carbon costs for charterers. This study yields a positive result for the equal division of ETSs' exercising competence in cross-regional maritime transport and provides evidence for sector-specific ETS links based on quantitative analysis.
Subject(s)
Carbon , Greenhouse Gases , Costs and Cost Analysis , ChinaABSTRACT
Tidal zones providing habitats are particularly vulnerable to microplastic (MP) pollution. In this study, the effects of tidal cycles on the transport of MPs (4-6 µm polyethylene, PE1; 125 µm polyethylene, PE2; and 5-6 µm polytetrafluoroethylene, PFTE) in porous media combined with various environmental and MPs properties were systemically investigated. The results indicated that smaller substrate sizes exhibited higher retention percentages compared to those of larger substrate sizes under different tidal cycles. In terms of the size of MPs, a larger size (same density) was found to result in enhanced retention of MPs in the column. As the number of tidal cycles increased, although the transport of MPs from the substrate to the water phase was enhanced, PE1 was washed out more with the change in water level, compared to PTFE. Additionally, more MPs were retained in the column with the increase of salinity and the decrease of flow velocity under the same tidal cycles. Ultraviolet and seawater aged PE1 showed enhanced transport, while aged PTFE showed enhanced retention under the same tidal cycles. These results can help understand the MP behaviors in the shoreline environment and provide support for future cleanup and sampling in tidal zones.
Subject(s)
Microplastics , Water Pollutants, Chemical , Environmental Monitoring , Plastics/chemistry , Polyethylene , Polymers , Polytetrafluoroethylene , Water , Water Pollutants, Chemical/analysisABSTRACT
Oil spills may affect ecosystems and endanger public health. In this study, we developed a novel and dual responsive nanoclay/sodium alginate (NS) washing fluid, and systematically evaluated its application potential in oiled shoreline cleanup. The characterization results demonstrated that sodium alginate combined with nanoclay via hydrogen bonds, and was inserted into the interlayer spacing of nanoclay. Adding sodium alginate reduced surface and interfacial tensions, while increasing the viscoelasticity of the washing fluid. Batch experiments were conducted to investigate oil removal performance under various conditions. Additionally, the factorial design analysis showed that three single factors (temperature, oil concentration, and salinity), and two interactive effects (temperature/salinity; and oil concentration/HA) displayed significant effects on the oil removal efficiency of the NS washing fluid. Compared to the commercial surfactants, the NS composite exhibited satisfactory removal efficiencies for treating oily sand. Green materials-stabilized Pickering emulsion can potentially be used for oil/water separation. The NS washing agent displayed excellent pH- and Ca2+- responsiveness, generating transparent supernatants with low oil concentration and turbidity. Our work opens an interesting avenue for designing economical, high performance, and green washing agents.
Subject(s)
Alginates , Petroleum Pollution , Ecosystem , Petroleum Pollution/analysis , Salinity , SandABSTRACT
In-situ burning can be used to prevent oil spreading in oil spill response. In this study, a steady-state Gaussian plume model was applied to analyze the concentration distribution of fine particulate matter produced by in-situ burning, as well as to assess the health risks associated with different combustion methods and ambient conditions, in reference to three simulation scenarios. The spatial and temporal distribution of emission sources can affect the dispersion pattern. The distribution into an array of different burning locations ensures better dispersion of emissions, thereby preventing the formation of high concentration regions. The wind and atmosphere stability play an important role in pollution dispersion. Lower wind and temperature inversion can seriously hinder the diffusion of pollutants. The health risk to technical staff adjacent to the burning areas is a serious concern, and when the community is more than 20 km away from the burning zone, there is few risks. Through simulation, the influences of combustion methods and natural factors on the concentration and diffusion of pollutants are evaluated. The results can help provide an optimized burning strategy for oil spill response in the Arctic area.
Subject(s)
Air Pollutants , Petroleum Pollution , Air Pollutants/analysis , Environmental Monitoring , Humans , Particulate Matter/analysis , WindABSTRACT
The use of machine learning techniques in waste management studies is increasingly popular. Recent literature suggests k-fold cross validation may reduce input dataset partition uncertainties and minimize overfitting issues. The objectives are to quantify the benefits of k-fold cross validation for municipal waste disposal prediction and to identify the relationship of testing dataset variance on predictive neural network model performance. It is hypothesized that the dataset characteristics and variances may dictate the necessity of k-fold cross validation on neural network waste model construction. Seven RNN-LSTM predictive models were developed using historical landfill waste records and climatic and socio-economic data. The performance of all trials was acceptable in the training and validation stages, with MAPE all less than 10%. In this study, the 7-fold cross validation reduced the bias in selection of testing sets as it helps to reduce MAPE by up to 44.57%, MSE by up to 54.15%, and increased R value by up to 8.33%. Correlation analysis suggests that fewer outliers and less variance of the testing dataset correlated well with lower modeling error. The length of the continuous high waste season and length of total high waste period appear not important to the model performance. The result suggests that k-fold cross validation should be applied to testing datasets with higher variances. The use of MSE as an evaluation index is recommended.
ABSTRACT
The 2010 Deepwater Horizon (DWH) blowout released 3.19 million barrels (435â¯000 tons) of crude oil into the Gulf of Mexico. Driven by currents and wind, an estimated 22â¯000 tons of spilled oil were deposited onto the northeastern Gulf shorelines, adversely impacting the ecosystems and economies of the Gulf coast regions. In this work we present field work conducted at the Gulf beaches in three U.S. States during 2010-2011: Louisiana, Alabama, and Florida, to explore endogenous mechanisms that control persistence and biodegradation of the MC252-oil deposited within beach sediments as deep as 50 cm. The work involved over 1500 measurements incorporating oil chemistry, hydrocarbon-degrading microbial populations, nutrient and DO concentrations, and intrinsic beach properties. We found that intrinsic beach capillarity along with groundwater depth provides primary controls on aeration and infiltration of near-surface sediments, thereby modulating moisture and redox conditions within the oil-contaminated zone. In addition, atmosphere-ocean-groundwater interactions created hypersaline sediment environments near the beach surface at all the studied sites. The fact that the oil-contaminated sediments retained near or above 20% moisture content and were also eutrophic and aerobic suggests that the limiting factor for oil biodegradation is the hypersaline environment due to evaporation, a fact not reported in prior studies. These results highlight the importance of beach porewater hydrodynamics in generating unique hypersaline sediment environments that inhibited oil decomposition along the Gulf shorelines following DWH.
Subject(s)
Petroleum Pollution , Petroleum , Water Pollutants, Chemical , Ecosystem , Environmental Monitoring , Gulf of Mexico , Petroleum/analysis , Petroleum Pollution/analysis , Water , Water Pollutants, Chemical/analysisABSTRACT
Coastal environment is one of the most important ecological and socioeconomic areas. However, increasing energy demand and economic development lead to a continuous gas and oil exploration, production, and traffics, which notably raise the risk of oil spill accidents in coastal areas. Sensitivity assessment aiming to determine the coastal features that would be severely impaired by spill incidents is a crucial part of the response planning. In this study, an innovative framework for coastal sensitivity mapping that incorporated ecosystem service (ES) valuation and multidimensional assessment was proposed. Sensitivity was computed by valuing physical, biological, and social-economical indicators from ES perspective and separating each indicator into specific coastal domains. For different ES typologies, provisioning services contributed most to the overall ES value followed by culture services, supporting services, and regulating services. For ES value in different coastal domains, the highest value was recorded in the water column followed by water surface, shoreline, and seabed. However, the shoreline ranked highest regarding the ES value per ha. Sensitivity assessment revealed that sensitive areas differed in different domains, both in distribution and extent. Compared with the scoring method, the ES valuation method showed more coincidence with Ecologically and Biologically Significant Areas (EBSA), representing a more precise and practical approach for sensitivity assessment. A three-dimensional (3D) oil spill model was also applied to generate maps of oil contamination probability in shoreline, water surface, and water column. The obtained results highlighted the significance of incorporating different coastal domains into oil spill responses, and the urgent demand to broaden and deepen our understanding of ecological processes across the vertical coastal zones.
Subject(s)
Petroleum Pollution , Water Pollutants, Chemical , Canada , Ecosystem , Environmental Monitoring , Water Pollutants, Chemical/analysisABSTRACT
The shorelines frequently suffer adverse impacts from oil spill accidents. As one important technique of shoreline cleanup, the application of surface washing agents (SWAs) can help achieve high oil removal from shoreline substrates with less damage to affected zone. In this study, a framework for evaluation and selection of SWAs in oil spill incidents was constructed to better understand and apply this technique. A decision tree was firstly developed to illustrate all possible scenarios which are appropriate to use SWAs in consideration of oil collectability, shoreline character, types and amount of stranded oil, and cleanup requirement. Based on literature review, theoretical modeling, and experts' suggestions, an integrated multi-criteria decision analysis (MCDA) method was then come up to select the most preferred SWA from five aspects of toxicity, effectiveness, minimal dispersion, demonstrated field test, and cost. Its suitability and rationality were proved by a hypothetical case. In addition, sensitivity analysis was performed by changing the weight of each criterion independently to check the priority rank of alternatives, and it also verified the robustness and stability of this model. The presented framework has significant implications for future research and application of SWAs in the shoreline cleanup.
Subject(s)
Petroleum Pollution , AccidentsABSTRACT
The COVID-19 pandemic has induced many issues for all societal sectors, in particular in the production and disposal of municipal solid waste. This may be because successive easing and reimposing of lockdown measures have deeply changed people's movements, consumers' behaviors and waste management. Previous studies have focused on the short-term effects of lockdowns on waste changes, yet there is little knowledge on waste variations during successive lockdowns and unlocking of various lockdown intensities. Moreover, the efficiency of lockdown and its relation to people's mobility in different countries are still not clear. Here, we studied the variations of amount and composition of municipal solid waste before the pandemic in 2019 and during the pandemic in 2020-2021 in USA, Brazil, Canada, UK, France and Italy. We used a stringency index and a composite mobility index to assess the lockdown intensity and people's movements. Results show that the mobility index sharply decreased with lockdown intensity, and enforcing measures were more efficient in France and Italy. Compared to 2019, prolonged lockdowns caused larger decreases in the quantity of commercial and construction wastes versus household waste. The initial implementation of lockdown or unlocking measures promoted inhabitants' consumption, generally leading to the increased waste amount, by about 9% for Trento and 12% for Montreal at the beginning of lockdown, respectively. Moreover, larger variations in the waste amount in Trento, from - 25.3 to 9.8%, were in line with higher lockdown intensity compared to those in Montreal, from - 9.5 to 12.7%, affected by people's mobility, consumers' behaviors and waste management. SUPPLEMENTARY INFORMATION: The online version contains supplementary material available at 10.1007/s10311-021-01290-z.
ABSTRACT
Spilled oil frequently reaches the shorelines and affects coastal biota and communities. The application of surface washing agents is an important shoreline cleanup technique that can help remove stranded oil from substrate surfaces with the advantages of high removal efficiency, low toxicity, and strong economic viability. In this study, the investigation into the oil removal from contaminated sand using a surface washing agent under variable environmental conditions was conducted. A preliminary test was conducted to obtain the optimal combination of operating factors of surface washing agent-to-oil ratio (SOR) 2:1, mixing speed 150 rpm, and mixing time 30 min. The results of single-factor experiments showed that high temperature and humic acid concentration of flush water contributed to the performance of a surface washing agent, while salinity and kaolinite concentration could inhibit its performance. The factorial analysis revealed the main effects of temperature and salinity, and the interactive effects of temperature and salinity as well as salinity and humic acid concentration that were significant to the washing efficiency of the surface washing agent. In addition, the comprehensive assessment of a surface washing agent from the aspects of toxicity, detergency, dispersion properties, and field trials was conducted. The results have significant implications for future application of surface washing agents in the shoreline cleanup.
Subject(s)
Petroleum , Water Pollutants, Chemical , Salinity , Sand , Temperature , Water Pollutants, Chemical/analysisABSTRACT
The beef cattle production has been considered as one of the largest sources of greenhouse gases (GHGs) emission. A large amount of GHGs including N2O and CH4 from enteric fermentation and manure are discharged to atmosphere during beef-production process. In addition, a substantial amount of GHGs is also emitted from many other related processes such as feed production, transportation, and energy consumption. In this study, an emission assessment model was developed to quantify the amount of regional GHGs produced from the beef cattle production process. A case study was conducted based on the beef production in Saskatchewan, Canada. The results demonstrated that the GHG emissions from the annual marketed beef cattle in Saskatchewan in 2014 were 8.52 × 109 kg CO2-eq in total and the cattle-source GHGs (enteric CH4, manure CH4, and manure N2O emission) accounted for more than 90% of the total emission. Sensitivity analysis showed that the most critical factors influencing the GHG emission included feedlot manure handling system, cattle diet, feed additives, maximum methane producing capacity (Bo), and climate (temperature, precipitation, and potential evapotranspiration). The potential impacts of climate change on GHG emission from beef cattle production in Saskatchewan were also investigated. An overall decrease in the GHG emission can be observed due to the climate change, which are 3.67%, 4.96%, and 6.63% for 2020-2039, 2040-2059, and 2060-2099, respectively.
Subject(s)
Greenhouse Gases , Red Meat , Animals , Cattle , Greenhouse Effect , Manure , Methane , Nitrous Oxide , SaskatchewanABSTRACT
The study explored the chronic toxicity of triclosan to green microalga Chlorococcum sp. under multiple interactions among multiple environmental conditions. This is the first study on chronic algal toxicity to combine synchrotron-based Fourier transform infrared spectromicroscopy, factorial analysis, principal component analysis, and stepwise-cluster analysis. Such a combination helps to reveal the toxic mechanism at the molecular level and explore the inner correlationship among multiple environmental conditions. In the 120-h test, nitrogen content became the most significant factor of the physiochemical properties. Some insignificant factors in the 48-h test became significant in the 120-h test. Temperature * nitrogen content, temperature * phosphorus content, and pH * phosphorus content were the most significant two-order interactions. Temperature * pH * NaCl concentration and temperature * NaCl concentration * phosphorus content were the most significant three-order interactions. More high-order interactions became significant in the 120-h test, indicating the complexity and impacts of all the factors may increase when time was extended. The chronic toxicity of triclosan presented more distinguishable variations among treatments based on biochemical alterations. These results demonstrate that the sensitivity and fragility of algae to triclosan can be amplified with time extension. Long-term exposure can be applied to better evaluate and predict the environmental toxicity behavior of triclosan. It can also help with environmental evaluation and risk management of real-world triclosan toxicity.
Subject(s)
Chlorophyta/drug effects , Chlorophyta/metabolism , Environmental Exposure/adverse effects , Spectroscopy, Fourier Transform Infrared/instrumentation , Synchrotrons , Triclosan/toxicity , Water Pollutants, Chemical/toxicity , Principal Component Analysis , Time FactorsABSTRACT
This study explored the long-term impacts of a pulse disturbance of triclosan on five nontarget green algae in Lake Erie. Comprehensive analyses were performed using multiple physiological end points at community and subcellular scales. The toxic mechanism of triclosan in a wide range of concentrations was analyzed. The diverse sensitivity of algae species and complex interrelationships among multiple end points were revealed. The results showed the taxonomic groups of algae were the key issue for sensitivity difference. High doses of triclosan caused irreversible damage on algae, and environmentally relevant doses initiated either inhibition or stimulation. Smaller cells had higher sensitivity to triclosan, while larger cells had a wider size variation after exposure. Colonial cells were less sensitive than unicells. For chlorophyll, there were better dose-response relationships in Chlorococcum sp., Chlamydomonas reinhardtii CPCC 12 and 243 than Asterococcus superbus and Eremosphaera viridis. For chlorophyll fluorescence, Fv/ Fm was the most sensitive parameter, and qN was more sensitive than qP. Triclosan showed long-term effects on biochemical components, such as lipids, proteins, and nucleic acids. The findings will be helpful for a systematic and complete assessment of triclosan toxicity in natural waters and the development of appropriate strategies for its risk management.
Subject(s)
Chlorophyta , Triclosan , Water Pollutants, Chemical , Chlorophyll , LakesABSTRACT
This study explored the toxicity of triclosan in the presence of TiO2 P25 to the green alga Eremosphaera viridis in Lake Erie. Multiple physicochemical end points were conducted to perform a comprehensive analysis of the toxic effects of individual and combined pollutants. Fourier transform infrared spectromicroscopy and synchrotron-based X-ray fluorescence imaging were first documented to be applied to explore the distribution variation of macromolecules and microelements in single algal cells in interactive toxicity studies. The results were different based on different triclosan concentrations and measurement end points. Comparing with individual pollutants, the toxicity intensified in lipids, proteins, and oxidative stress at 1000 and 4000 µg/L triclosan in the presence of P25. There were increases in dry weight, chlorophyll content, lipids, and catalase content when cells were exposed to P25 and 15.625 µg/L triclosan. The toxicity alleviated when P25 interacted with 62.5 and 250 µg/L triclosan compared with triclosan-only exposure. The reasons could be attributed to the combination of adsorption, biodegradation, and photocatalysis of triclosan by algae and P25, triclosan dispersion by increased biomass, triclosan adherency on algal exudates, and triclosan adsorption site reduction on algae surface owing to P25's taking over. This work provides new insights into the interactive toxicity of nanoparticles and personal care products to freshwater photosynthetic organisms. The findings can help with risk evaluation for predicting outcomes of exposure to mixtures and with prioritizing further studies on joint toxicity.