Light Enables the Cathodic Interface Reaction Reversibility in Solid-State Lithium-Oxygen Batteries.

Limited triple-phase boundaries arising from the accumulation of solid discharge product(s) in solid-state cathodes (SSCs) pose a challenge to high-property solid-state lithium-oxygen batteries (SSLOBs). Light-assisted SSLOBs have been gradually explored as an ingenious system; however, the fundamental mechanisms of the SSCs interface behavior remain unclear. Here, we discovered that light assistance can enhance the fast inner-sphere charge transfer in SSCs and regulate the discharge products with spherical particles generated via the surface growth model. Moreover, the high photoelectron excitation and transportation capabilities of SSCs can retard cathodic catalytic decay by avoiding structural degradation of the cathode with a reduced charge voltage. The light-induced SSLOBs exhibited excellent stability (170 cycles) with a low discharge-charge polarization overpotential (0.27 V). Furthermore, transparent SSLOBs with exceptional flexibility, mechanical stability, and multiform shapes were fabricated for theory-to-practical applications in sunlight-induced batteries. Our study opens new opportunities for the introduction of solar energy into energy storage systems.

Fabrication of light, flexible and multifunctional graphene nanoribbon fibers via a 3D solution printing method.

Graphene oxide nanoribbons (GONRs) are one of the most promising carbon based materials. The integration of 2D GONR sheets into macroscopic materials, such as continuous fibers or film, leads the way in translating the good properties of individual GONR sheets into macroscopic and ordered materials for future applications. In this study, we first report the fabrication of GONR fibers utilizing GONR sheets as the raw material without any supporting surfactant or polymer. The method of fabricating fibers is referred to as '3D solution printing'. GONR fibers exhibit good mechanical and electrical properties, whose tensile strength and electrical conductivity could reach up to 95 MPa and 680 S cm-1, respectively. Hence, the fabricated 3D integrated circuits are lighter and smaller compared to traditional metal circuits, and with high electrical properties. The 3D integrated circuits, therefore, have a bright future prospect.

External Stimuli-Induced Welding of Dynamic Cross-Linked Polymer Networks.

Thermosets have been crucial in modern engineering for decades, finding applications in various industries. Welding cross-linked components are essential in the processing of thermosets for repairing damaged areas or fabricating complex structures. However, the inherent insolubility and infusibility of thermoset materials, attributed to their three-dimensional network structure, pose challenges to welding development. Incorporating dynamic chemical bonds into highly cross-linked networks bridges the gap between thermosets and thermoplastics presenting a promising avenue for innovative welding techniques. External stimuli, including thermal, light, solvent, pH, electric, and magnetic fields, induce dynamic bonds' breakage and reformation, rendering the cross-linked network malleable. This plasticity facilitates the seamless linkage of two parts to an integral whole, attracting significant attention for potential applications in soft actuators, smart devices, solid batteries, and more. This review provides a comprehensive overview of dynamic bonds employed in welding dynamic cross-linked networks (DCNs). It extensively discusses the classification and fabrication of common epoxy DCNs and acrylate DCNs. Notably, recent advancements in welding processes based on DCNs under external stimuli are detailed, focusing on the welding dynamics among covalent adaptable networks (CANs).

A pH-responsive, injectable and self-healing chitosan-coumarin hydrogel based on Schiff base and hydrogen bonds.

Smart hydrogels have shown great potential applications in disease treatment due to their controlled and local drug-release ability. Herein, a smart hydrogel with pH-responsive, injectable, and self-healing properties for controlled release of taxifolin (TFL) was prepared by freezing-thawing and photo-crosslinking methods. The crosslinking network of hydrogels (CS-CA hydrogels) was constructed by the hydrogen bonds, Schiff base bonds, and cyclobutane rings using chitosan (CS) and coumarin (CA) as raw materials. The CS-CA hydrogel demonstrated a compressive strength of 1.04 MPa, a self-healing efficiency of 99.9 %, and could maintain structural and functional integrity after injection. In addition, the drug release rate and shape of the CS-CA hydrogels were tunable due to its pH sensitivity. The TFL cumulative release reached 60 % within 12 h at pH = 4, and after equilibration, the cumulative release of TFL at pH = 4 (80 %) was significantly higher than at pH = 9.2 (50 %). The CCK8 experiment showed that the resulting hydrogel had no cytotoxicity. Meanwhile, subcutaneous implantation experiments in mice showed that the CS-CA hydrogels had favorable biodegradability and compatibility.

A Facile Route to Synthesize Nanographene Reinforced PBO Composites Fiber via in Situ Polymerization.

The polymer matrix with introduced carbon-based nanofiber displays fascinating properties. They have inspired extensive research on the synthesis of polymer composites, which have been applied in catalysis, electronics, and energy storage. In this report, we reported a facile and efficient method to prepare poly(p-phenylene benzobisoxazole) (PBO)/nanographene (PNG) composites fibers via in-situ polymerization, accompanied by the reduction from (nanographene oxide) NGO to (nanographene) NG. By tuning the ratio of feeding PBO monomer to NGO, various composites fibers with 0.1⁻1 wt % contents of NG were obtained. The efficient PBO chains grafting made NG uniformly disperse in the PBO matrix, and it also increased the uniformity of the packing orientation of PBO chains. Consequently, the tensile strength, tensile modulus, and thermal stability of the obtained PNG composites fibers had been improved significantly. In addition, the composites fibers with 0.5 wt % NG exhibited a 25% increment in tensile strength, and a 41% enhancement in tensile modulus compared with neat PBO fibers. It reveals an excellent reinforcement to PBO composites fibers with NG.