Nanoparticle platform to modulate reaction mechanism of phenothiazine photosensitizers.

Herein, we report on the synthesis of photosensitizing nanoparticles in which the generation of different oxidizing species, i.e., singlet oxygen (1O2) or radicals, was modulated. Sol gel and surface chemistry were used to obtain nanoparticles with specific ratios of dimer to monomer species of phenothiazine photosensitizers (PSs). Due to competition between the reactions involving electron transfer within dimer species and energy transfer from monomer triplets to oxygen, the efficiency of 1O2 generation could be controlled. Nanoparticles with an excess of dimer have an 1O2 generation efficiency (S(delta)) of 0.01 while those without dimer have a S(delta) value of 0.4. Furthermore, we demonstrate that the PS properties of the nanoparticles are not subjected to interference from the external medium as is commonly the case for free PSs, i.e., PS ground and triplet states are not reduced by NADH and ascorbate, respectively, and singlet excited states are less suppressed by bromide. The modulated 1O2 generation and the PS protection from external interferences make this nanoparticle platform a promising tool to aid in performing mechanistic studies in biological systems. Also, it offers potential application in technological areas in which photo-induced processes take place.

Molecular mapping by low-energy-loss energy-filtered transmission electron microscopy imaging.

Structure-function relationships in supramolecular systems depend on the spatial distribution of molecules, ions, and particles within complex arrays. Imaging the spatial distribution of molecular components within nanostructured solids is the objective of many recent techniques, and a powerful tool is electron spectroscopy imaging in the transmission electron microscope (ESI-TEM) in the low-energy-loss range, 0-80 eV. This technique was applied to particulate and thin film samples of dielectric polymers and inorganic compounds, providing excellent distinction between areas occupied by various macromolecules and particles. Domains differentiated by small changes in molecular composition and minor differences in elemental contents are clearly shown. Slight changes in the molecules produce intensity variations in molecular spectra that are in turn expressed in sets of low-energy-loss images, using the standard energy-filtered transmission electron microscopy (EFTEM) procedures. The molecular map resolution is in the nanometer range and very close to the bright-field resolution achieved for the same sample, in the same instrument. Moreover, contrast is excellent, even though sample exposure to the electron beam is minimal.

Formation of calcium crystallites in dry natural rubber particles.

In this paper, the effects of drying and aging of natural rubber particles of Hevea brasiliensis are studied. The evolutions of the particle morphology and of the elemental distribution are investigated using electron-energy-loss spectroscopy imaging in a low-energy transmission electron microscope (ESI-TEM). It is found that when the sample is aged, calcium salt crystallites are formed around the particles. Fusion of these crystallites with time to form larger crystals shows evidence of ion mobility in the dry rubber matrix. Electron diffraction patterns and elemental mapping analysis indicate the crystals to be calcium sulfate. These crystallites are closely associated with membrane materials of the rubber particle and are surprisingly compatible with the hydrocarbon matrix of the rubber particle. It is proposed that polar sites on the membrane materials provide nucleation sites for the crystallization of calcium and sulfate ions from the latex serum.

A versatile x-ray microtomography station for biomedical imaging and materials research.

An x-ray microtomography station implemented at the X-ray Applied Crystallography Laboratory of the State University of Campinas is described. The station is based on a propagation based phase contrast imaging setup with a microfocus source and digital x-ray area detectors. Due to its simplicity, this setup is ideal for fast, high resolution imaging and microtomography of small biological specimens and materials research samples. It can also be coupled to gratings to use and develop new techniques as the harmonic spatial coherent imaging, which allow scattering contrast imaging. Details of the experimental setup, equipment, and software integration are described. Test microtomography for setup commissioning and characterization is shown. We conclude that phase contrast enhanced x-ray imaging and microtomography with resolution below 5 µm voxel size are possible and data sets as wide as 2000 × 2000 × 2000 voxels are obtained with this instrumentation.

Skim and cream natural rubber particles: colloidal properties, coalescence and film formation.

Cream and skim fractions of freshly tapped natural rubber latex have been studied using atomic force microscopy and scanning electric potential microscopy to elucidate the topology and charge properties in film formation. Elemental distribution maps of the particles have also been obtained using electron energy-loss imaging in a low-energy transmission electron microscope. The two rubber fractions are obtained by centrifugation. The cream fraction is stable while rapid coagulation occurs in the skim fraction. After removal of the coagulum, no further coagulation occurs and the remaining skim rubber particles are stable. The rubber particles from the cream rubber particles contain higher amount of adsorbed protein-phospholipid materials compared to those in the "self-cleaned" skim fraction. This difference in membrane property has a significant impact on the spreading of the cis-1,4-polyisoprene cores, their coalescence and film formation behavior. Coalescence of cream particles appears to be hindered by the membrane materials, forming a rough film that retains the topology of individual particles. Skim particles coalesce more readily, forming relatively smooth films.

Effect of lipid coating on the interaction between silica nanoparticles and membranes.

Lipid coating is a method highly used to improve the biocompatibility of nanoparticles (NPs), even though its effect on the NP properties is still object of investigation. Herein, silica NPs containing methylene blue, which is a photosensitizer used in a variety of biomedical applications, were coated with a phospholipid bilayer. Regarding the photophysical properties, lipid-coating did not cause significant changes since bare and lipid-coated NPs presented very similar absorption spectra and generated singlet oxygen with similar efficiencies. However, NP interaction with cells and membrane mimics was totally different for bare and lipid-coated NPs. Lipid-coated NPs were distributed through the cell cytoplasm whereas bare NPs were detected only in some vacuolar regions within the cells. Since cellular uptake and cytolocalization are influenced by NP adsorption on cell membranes, the interaction of lipid-coated and bare NPs were studied on a membrane mimic, i.e., Hybrid Bilayer Membranes (HBMs) made of different compositions of negatively charged and neutral lipids. Interactions of bare and lipid-coated NPs with HBMs were analyzed by Surface Plasmon Resonance Imaging. Bare NPs presented high adsorption and aggregation on HBMs independently of the surface charge. Conversely, lipid-coated NPs presented less aggregation on the membrane surface and the adsorption was dependent on the charges of the NPs and of the HBMs. Our results indicated that NPs aggregation on the membrane surface can be modulated by lipid coating, which affects the cytosolic distribution of the NPs.

Iron insertion and hematite segregation on Fe-doped TiO2 nanoparticles obtained from sol-gel and hydrothermal methods.

Iron-doped TiO(2) (Fe:TiO(2)) nanoparticles were synthesized by the sol-gel method (with Fe/Ti molar ratio corresponding to 1, 3, and 5%), followed by hydrothermal treatment, drying, and annealing. A similar methodology was used to synthesize TiO(2) and α-Fe(2)O(3) nanoparticles. For comparison, a mixture hematite/titania, with Fe/Ti = 4% was also investigated. Characterization of the samples using Rietveld refinement of X-ray diffraction data revealed that TiO(2) consisted of 82% anatase and 18% brookite; for Fe:TiO(2), brookite increased to 30% and hematite was also identified (0.5, 1.0, and 1.2 wt % for samples prepared with 1, 3, and 5% of Fe/Ti). For hematite/titania mixture, Fe/Ti was estimated as 4.4%, indicating the Rietveld method reliability for estimation of phase composition. Because the band gap energy, estimated as 3.2 eV for TiO(2), gradually ranged from 3.0 to 2.7 eV with increasing Fe content at Fe:TiO(2), it can be assumed that a Fe fraction was also inserted as dopant in the TiO(2) lattice. Extended X-ray absorption fine structure spectra obtained for the Ti K-edge and Fe K-edge indicated that absorbing Fe occupied a Ti site in the TiO(2) lattice, but hematite features were not observed. Hematite particles also could not be identified in the images obtained by transmission electron microscopy, in spite of iron identification by elemental mapping, suggesting that hematite can be segregated at the grain boundaries of Fe:TiO(2).

Synthesis and characterization of magnetic mesoporous particles.

Magnetic mesoporous particles were synthesized and their magnetic and structural properties are reported. The synthesis procedure consists of four steps: (i) preparation of magnetite colloidal nanoparticles; (ii) growth of a silica layer; (iii) development of the mesoporous structure and (iv) template removal. Two different methods for the template removal were studied and their effectiveness was discussed. Magnetization and Mössbauer spectroscopy measurements showed superparamagnetic behavior for the particles at room temperature. X-ray diffraction and nitrogen adsorption measurements showed a mesoporous MCM-41 structure with 2.48nm pore diameter and 1023m(2)/g total area.

Preparation and characterization of ethanol-treated silk fibroin dense membranes for biomaterials application using waste silk fibers as raw material.

The possibility of producing valued devices from low cost natural resources is a subject of broad interest. The present study explores the preparation and characterization of silk fibroin dense membranes using waste silk fibers from textile processing. Morphology, crystallinity, thermal resistance and cytotoxicity of membranes as well as the changes on the secondary structure of silk fibroin were analyzed after undergoing treatment with ethanol. Membranes presented amorphous patterns as determined via X-ray diffraction. The secondary structure of silk fibroin on dense membranes was either random coil (silk I) or beta-sheet (silk II), before and after ethanol treatment, respectively. The sterilized membranes presented no cytotoxicity to endothelial cells during in vitro assays. This fact stresses the material potential to be used in the fabrication of biomaterials, as coatings of cardiovascular devices and as membranes for wound dressing or drug delivery systems.

Efficient preparation of polystyrene/silica colloidal nanocomposite particles by emulsion polymerization using a glycerol-functionalized silica sol.

Colloidally stable polystyrene/silica nanocomposite particles of around 200-400 nm diameter and containing 22-28 wt % silica can be readily prepared by aqueous emulsion polymerization at 60 degrees C using a cationic azo initiator in combination with a commercially available glycerol-functionalized ultrafine aqueous silica sol in the absence of any surfactant, auxiliary comonomer, or nonaqueous cosolvent. Optimization of the initial silica sol concentration allows relatively high silica aggregation efficiencies (up to 95%) to be achieved. Control experiments confirm the importance of selecting a cationic initiator, since nanocomposite particles were not formed when using an anionic persulfate initiator. Similarly, the glycerol groups on the silica sol surface were also shown to be essential for successful nanocomposite particle formation: use of an unfunctionalized ultrafine silica sol in control experiments invariably led to polystyrene latex coexisting with the silica nanoparticles, rather than efficient nanocomposite formation. Electron spectroscopy imaging transmission electron microscopy studies of ultramicrotomed polystyrene/silica nanocomposite particles indicate well-defined "core-shell" particle morphologies, which is consistent with both X-ray photoelectron spectroscopy and aqueous electrophoresis studies.

ESI-TEM imaging of surfactants and ions sorbed in Stöber silica nanoparticles.

The sorption of surfactants and NaCl in silica nanosized particles creates unexpected spatial distributions of solutes that were evidenced by electron spectroscopy imaging in the transmission electron microscope (ESI/TEM). The spectral images show that simple ions (Na(+), Cl(-), Br(-)) are actually absorbed within the particles irrespective of their charges, while surfactant chains are adsorbed at the particle surfaces. The expected effect of the surfactants on particle aggregation is also observed in the micrographs. In the case of salt, close-packed silica particle arrays are formed at low ionic strength, but only coarse aggregates form at higher salt concentrations. The particles absorb both Na(+) and Cl(-) ions in similar amounts, from 0.5 mol L(-)(1) NaCl, but Na(+) ions are depleted from the particles' immediate outer vicinity, where Cl(-) ions are in turn accumulated. These results confirm that Stöber silica nanoparticles are highly porous and reveal their potential usefulness as carriers of small molecules and ions, due to the small particle size, exceptional colloidal stability, and this newly found sorption behavior.

Controlled nanoparticle assembly by dewetting of charged polymer solutions.

In this paper, we present an alternative approach for controlled nanoparticle organization on a solid substrate by applying dewetting patterns of charged polymer solutions as a templating system. Thin films of charged polymer solutions dewet a solid substrate to form complex dewetting patterns that depend on the polymer charge density. These patterns, ranging from polygonal networks to elongated structures that are stabilized by viscous forces during dewetting, serve as potential templates for two-dimensional nanoparticle organization on a solid substrate. Thus, while nanoparticles dried in pure water undergo self-assembly to form close-packed arrays, addition of charged polymer in the dispersion leads to the formation of open structures that are directed by the dewetting patterns of the polymer solution. In this study, we focus on the application of elongated structures resulting from dewetting of high-charge-density polymer solutions to align nanoparticles of silica and gold into long chains that are several micrometers in length. The particle ordering process is a two-step mechanism: an initial confinement of the nanoparticles in the dewetting structures and self-assembly of the particles within these structures upon further drying by lateral capillary attractions.