ABSTRACT
We present the fabrication and laser performance of thulium-holmium co-doped silica fibers when cladding pumped at â¼790â nm. By using the hybrid gas phase-solution doping process in conjunction with the MCVD preform fabrication technique, the doping concentration and the Tm:Ho ratio were varied to study the energy transfer efficiency from Tm3+ to Ho3+. Our study indicates that for a thulium concentration that has resulted in an efficient two-for-one cross- relaxation process with 790â nm pumping, and while maintaining a Tm:Ho concentration ratio in the range â¼ 10 to 20, the energy transfer efficiency has reached above 75%. In a free-running laser cavity, the pump power limited laser output of 38W with a slope efficiency of 56% at 2.1 microns is demonstrated.
ABSTRACT
We report a hybrid process by combining both vapor-phase and solution-doping techniques of rare-earth doped preform fabrication in conjunction with the MCVD technique, in order to fabricate highly efficient Tm-doped laser fibers. The proposed fabrication route takes advantage of co-doping silica with high alumina content through the vapor-phase doping process, which is otherwise difficult to achieve using conventional solution doping technique. In addition, by employing the solution doping method, high-purity thulium halide precursors that have low vapor pressures up to several hundred degree Celsius. These high-purity thulium halide precursors can be used to dope the fiber core region with a high thulium concentration that is optimized for an efficient two-for-one cross-relaxation process for 79xnm diode pumped thulium-doped fiber laser. Fibers fabricated using the hybrid approach show more homogeneous and flat-top dopant profiles, compared with the conventional approach, where both aluminum and thulium are incorporated in the core through solution doping. This will ensure that more doped region will take part in the cross-relaxation process. Superior laser performance with a slope efficiency of >70% in the two-micron band has been demonstrated when diode pumped at ~790nm.
ABSTRACT
We report the temperature dependent performance of an O-band bismuth (Bi)-doped fiber amplifier (BDFA) in the temperature range from -60 to +80°C. At room temperature, maximum gains of 27 and 40 dB with noise figures (NFs) of 4.3 and 4.8 dB are measured for -23 dBm signal power in the single and double pass BDFA, respectively. An increment in gain and reduction in NF is observed as the ambient temperature of the BDFA is reduced. In the double pass BDFA, the temperature dependent gain coefficient from -60 to +80°C is found to be around -0.02 and -0.03 dB/°C across the wavelength band of 1300-1360 nm for -10 and -23 dBm signal powers, respectively. We also study the gain and NF characteristics with pump power and signal power at different temperatures, and a maximum gain of 45 dB is obtained at -60°C for -30 dBm signal power.
ABSTRACT
In this Letter, we investigate and compare the gain and noise figure characteristics of bismuth (Bi)-doped fiber amplifiers configured in both single and double signal pass implementations. A maximum gain of 25 dB and a noise figure of 4 dB is measured at 1360 nm in the single pass configuration for -23 dBm input signal power, whereas in the double pass configuration the gain of the amplifier is improved significantly by 14 dB allowing us to achieve a gain of 39 dB with a noise figure of 5 dB. To the best of our knowledge, this is the highest gain reported to date using Bi-doped fiber as a gain medium. Furthermore, we also study the gain and noise figure dependency on pump power, signal power, and pump wavelength for the double pass amplifier configuration. We observed similar gain and noise figure performance in the double pass configuration to that of the single pass configuration but with the benefit of less pump power and a shorter length of the Bi-doped fiber.
ABSTRACT
Rheological characteristics of Desi ghee were investigated at 18, 24, 30 and 36 °C. The steady shear properties were evaluated by varying the shear rate from 0.01 to 100 s-1 and the dynamic shear properties were studied by varying strain and frequency sweep from 0.01 to 100% and 0.1 to 100 rad s-1, respectively. At the four selected temperatures, the ghee samples displayed non-Newtonian shear thinning behavior with flow behavior index (n) ranging from 0.224 to 0.911. As the shear rate increased from 0 to 100 s-1, the values of dynamic viscosity decreased from 54 to 8.14, 20.01 to 1.05, 1.33 to 0.295, and 3.02 to 0.0025 Pa s at 18, 24, 30 and 36 °C, respectively. Out of four rheological models (Power-law or Ostwald-de Waele, Herschel-Bulkley, Casson, and Bingham model) fitted to the shear rate and stress data, the Ostwald model was found to be superior in predicting the shear rate-stress data at 18 °C, whereas Ostwald-de Waele and Herschel-Bulkley models predicted all the data points over the temperature range of 24-30 °C, as observed by the values of coefficient of determination (R2 ), standard deviation (SD), and relative deviation percentage (Rd ). The value of activation energy (EA ), as calculated from Arrhenius type equation, was found to be 1.98 × 106 kJ mol-1 over the entire temperature range. The study also revealed that the magnitudes of dynamic shear viscosity (η*) were higher than those of the steady shear viscosity (η) at the four temperatures, indicating that the Cox-Merz rule was not applicable to the ghee samples.
ABSTRACT
We demonstrate a 1340 nm mode-locked Bismuth (Bi)-doped fiber laser without any saturable absorber. The effect of pump power on pulse width is studied, and a variation from 1.5 to 3 ns is reported. The output of the mode-locked Bi-doped fiber laser is further amplified using a master oscillator power amplifier configuration, and a peak power of 1.15 W is achieved. Soliton bunching is observed, and a true pulse width of 1.2 ps is reported from the measured autocorrelation trace. Stable operation of the mode-locked laser is verified from the radio-frequency spectrum with a fundamental repetition rate of 6.3 MHz, and SNR of 65 dB.
ABSTRACT
Bismuth (Bi)-doped phosphosilicate fibers have been fabricated by the modified chemical vapor deposition (MCVD)-solution doping technique under different process conditions. The influence of fabrication conditions on unsaturable loss in fibers has been investigated. Pump wavelength dependent Bi gain has been studied to obtain a flat gain over a wide bandwidth. A diode pumped all-fiber Bi-doped amplifier with a flat gain of 25±1 dB from 1320-1360 nm (40 nm) has been demonstrated for -10 dBm of input signal power with a noise figure (NF) ranging from 4-6 dB. Moreover, a small signal gain of 29 dB and a NF of 4.5 dB at 1340 nm has been achieved for an input signal power of -30 dBm.
ABSTRACT
Short wavelength operation (1650-1800 nm) of silica-based thulium-doped fiber amplifiers (TDFAs) is investigated. We report the first demonstration of in-band diode-pumped silica-based TDFAs working in the 1700-1800 nm waveband. Up to 29 dB of small-signal gain is achieved in this spectral region, with an operation wavelength accessible by diode pumping as short as 1710 nm. Further gain extension toward shorter wavelengths is realized in a fiber laser pumped configuration. A silica-based TDFA working in the 1650-1700 nm range with up to 29 dB small-signal gain and noise figure as low as 6.5 dB is presented.
ABSTRACT
We demonstrate a 60µm core diameter Yb free Er-La-Al doped single-trench fiber having a 0.038 ultra-low-NA, fabricated using conventional MCVD process in conjunction with solution doping technique. Numerical simulations predict an effective single mode operation with effective area varying from 1,820µm(2) to 1,960µm(2) (taking bend-induced modal distortion into account) for different thicknesses of trenches and resonant rings at a constant bend radius of 25cm. Moreover, all solid structure favors easy cleaving and splicing. Experimental measurements demonstrate a robust effective single mode operation. Furthermore, with a 4%-4% laser cavity, this fiber shows a record efficiency of 46% with respect to the absorbed pump power.
ABSTRACT
We experimentally demonstrate all-solid 10 and 20 µm core diameter multi-trench fibers for UV and visible wavelengths. Measurements ensure an effective single-mode operation over a wide range of bend radii, which is suitable for applications such as beam delivery. Both fibers were fabricated by the conventional modified chemical vapor deposition process, which is suitable for mass production. Moreover, all-solid fiber design ensures easy cleaving and splicing.
ABSTRACT
Bismuth-doped aluminosilicate fiber has been fabricated by the MCVD-solution doping method and characterized for its unsaturable loss and gain. The amplifier performance has been compared for a novel pumping wavelength of 1120 nm with the conventional pumping wavelength region of 1047 nm. Unsaturable loss was 65% and 35% at 1047 and 1120 nm, pump wavelengths, respectively. A maximum gain of about 8 dB at 1180 nm for a fiber length of 100 m was observed with 1120 nm pumping. Gain enhancement of 70% was achieved with the 1120 nm pump as compared to the 1047 nm pump. A further 3.5 dB gain was obtained on simultaneous pumping at 1047 and 1120 nm.
ABSTRACT
We experimentally demonstrate an all-solid Yb-doped 30 µm core diameter single trench fiber. Measurements ensure a robust effective single-mode operation without the need of tight coiling as required for conventional fibers thanks to the ultralow NA (â¼0.038) and resonant ring surrounding the core. All-solid and cylindrical design ensures the suitability for mass scale production with the added benefit of all-fiberized device structure. A compact master oscillator power amplifier (MOPA) has been built using this fiber delivering â¼23.5 ps pulses at 13.5 MHz repetition rate delivering up to â¼52 W of average output power corresponding to a pulse energy of â¼3.8 µJ and peak power of >160 kW, while maintaining â¼76% slope efficiency. The output beam exhibits a polarization extinction ratio of more than 15 dB and a M2 less than 1.15.
ABSTRACT
We report a novel "single trench fiber" design for mode area scaling of the fundamental mode while offering effective single mode operation for a compact fiber laser device. This fiber design allows very high suppression of the higher order modes by offering high loss and power delocalization. It has the advantages of low cost and easy fabrication thanks to all solid fiber design, cylindrical symmetry, and higher refractive index of core as that of the cladding. A Yb-doped single trench fiber with a 40 µm core diameter has been fabricated from modified chemical vapor deposition process in conjunction with solution-doping offering an effective mode area of as large as ~1,000 µm(2) at 1,060 nm for the bend radius of 20 cm. Detailed characterizations confirm a robust single mode behavior of the fiber. Comparative analysis with other fiber designs shows significant performance enhancement of effective single mode operation suitable for fiber laser applications.
ABSTRACT
We experimentally demonstrate a few-moded cladding-pumped multi-element fiber amplifier, comprising 4 Er/Yb co-doped signal fibers and 1 multimode pump-delivery fiber all of which are drawn together in a common polymer coating, providing a total spatial path multiplicity of 12. An average WDM signal gain of 18.3 dB and differential modal gain of 1.1 dB were achieved in the spectral range of 1542-1560 nm.
Subject(s)
Amplifiers, Electronic , Fiber Optic Technology/instrumentation , Lasers, Solid-State , Optical Fibers , Equipment DesignABSTRACT
A novel technological approach to space division multiplexing (SDM) based on the use of multiple individual fibers embedded in a common polymer coating material is presented, which is referred to as Multi-Element Fiber (MEF). The approach ensures ultralow crosstalk between spatial channels and allows for cost-effective ways of realizing multi-spatial channel amplification and signal multiplexing/demultiplexing. Both the fabrication and characterization of a passive 3-element MEF for data transmission, and an active 5-element erbium/ytterbium doped MEF for cladding-pumped optical amplification that uses one of the elements as an integrated pump delivery fiber is reported. Finally, both components were combined to emulate an optical fiber network comprising SDM transmission lines and amplifiers, and illustrate the compatibility of the approach with existing installed single-mode WDM fiber systems.
ABSTRACT
We experimentally demonstrate a few-mode erbium doped fiber amplifier (FM-EDFA) supporting 6 spatial modes with a cladding pumped architecture. Average modal gains are measured to be >20dB between 1534nm-1565nm with a differential modal gain of ~3dB among the mode groups and noise figures of 6-7dB. The cladding pumped FM-EDFA offers a cost effective alternative to core-pumped variant as low cost, high power multimode pumps can be used, and offers performance, scalability and simplicity to FM-EDFA design.
Subject(s)
Amplifiers, Electronic , Erbium/chemistry , Optical Fibers , Signal Processing, Computer-Assisted , Spectrum AnalysisABSTRACT
We report the first demonstration of an inline few-mode thulium doped fiber amplifier (TDFA) operating at 2µm for mode division multiplexed transmission. Similar gain and noise figure performance for both the LP(01) and LP(11) modes are obtained in a cladding pumped 2-mode group TDFA. A maximum gain of 18.3dB was measured at 1970nm with a 3dB gain bandwidth of 75nm while the average noise figure was measured to be between 7 and 8dB for wavelengths longer than 1970nm.
ABSTRACT
We report on high-energy nanosecond-pulsed fiber master oscillator power amplifier (MOPA) systems seeded by semiconductor laser diodes at 2 µm incorporating arbitrary pulse-shaping capabilities. Two MOPA systems, one based on direct diode modulation and the second using additional electro-optic modulator (EOM) based shaping, are investigated, with up to 0.5 mJ (25 kHz) and 1.0 mJ (12.5 kHz) pulse energies achieved, respectively, for 100 ns pulses with user-defined pulse shapes. Our results indicate that further energy scaling with shaped output pulses is primarily limited by the maximum pulse peak power available from the seed laser diode and the dynamic range offered by the first generation of EOMs at 2 µm.
ABSTRACT
Erbium-doped multi-element fiber (MEF) amplifiers have been fabricated to simultaneously amplify multiple transmission channels. MEF devices comprise of multiple single-core fibers (elements) combined in a common coating, with each element working as a single fiber in isolation. MEFs containing 3-elements and 7-elements have been fabricated and characterized. Each element of the fabricated MEFs provides nearly 32 dB of gain with a noise figure of <5 dB for an input signal level of -23 dBm at 1530 nm. Different permutations of element pairs within the MEFs were checked for crosstalk and none was detected, confirming the simultaneous multi-channel amplification capabilities of MEFs.
ABSTRACT
The effect of UV-C radiation on thylakoid arrangement, chlorophyll-a and carotenoid content and nitrogenase activity of the cyanobacterium Microchaete sp. was studied. Chlorophyll-a and carotenoid content increased gradually up to 48 h of UV-C exposure but declined with longer exposures. Nitrogenase activity decreased moderately with 6 to 12 h exposure and decreased substantially afterwards. When cells exposed to UV-C for 12 to 24 h, grown under fluorescent light for 144 h, nitrogenase activity increased to levels greater than in the control cells. The exposure of UV-C treated cells to fluorescent light, however, did not result in recovery of pigment content. In Microchaete sp. cells treated with UV-C for 144 h, thylakoid membranes became dense, were aggregated into bundles, and were surrounded by spaces devoid of cytoplasm.