Electrocatalytic Hydrogenation of Biomass-Derived Organics: A Review.

Sustainable energy generation calls for a shift away from centralized, high-temperature, energy-intensive processes to decentralized, low-temperature conversions that can be powered by electricity produced from renewable sources. Electrocatalytic conversion of biomass-derived feedstocks would allow carbon recycling of distributed, energy-poor resources in the absence of sinks and sources of high-grade heat. Selective, efficient electrocatalysts that operate at low temperatures are needed for electrocatalytic hydrogenation (ECH) to upgrade the feedstocks. For effective generation of energy-dense chemicals and fuels, two design criteria must be met: (i) a high H:C ratio via ECH to allow for high-quality fuels and blends and (ii) a lower O:C ratio in the target molecules via electrochemical decarboxylation/deoxygenation to improve the stability of fuels and chemicals. The goal of this review is to determine whether the following questions have been sufficiently answered in the open literature, and if not, what additional information is required:(1)What organic functionalities are accessible for electrocatalytic hydrogenation under a set of reaction conditions? How do substitutions and functionalities impact the activity and selectivity of ECH?(2)What material properties cause an electrocatalyst to be active for ECH? Can general trends in ECH be formulated based on the type of electrocatalyst?(3)What are the impacts of reaction conditions (electrolyte concentration, pH, operating potential) and reactor types?

Explaining the structure sensitivity of Pt and Rh for aqueous-phase hydrogenation of phenol.

Phenol is an important model compound to understand the thermocatalytic (TCH) and electrocatalytic hydrogenation (ECH) of biomass to biofuels. Although Pt and Rh are among the most studied catalysts for aqueous-phase phenol hydrogenation, the reason why certain facets are active for ECH and TCH is not fully understood. Herein, we identify the active facet of Pt and Rh catalysts for aqueous-phase hydrogenation of phenol and explain the origin of the size-dependent activity trends of Pt and Rh nanoparticles. Phenol adsorption energies extracted on the active sites of Pt and Rh nanoparticles on carbon by fitting kinetic data show that the active sites adsorb phenol weakly. We predict that the turnover frequencies (TOFs) for the hydrogenation of phenol to cyclohexanone on Pt(111) and Rh(111) terraces are higher than those on (221) stepped facets based on density functional theory modeling and mean-field microkinetic simulations. The higher activities of the (111) terraces are due to lower activation energies and weaker phenol adsorption, preventing high coverages of phenol from inhibiting hydrogen adsorption. We measure that the TOF for ECH of phenol increases as the Rh nanoparticle diameter increases from 2 to 10 nm at 298 K and -0.1 V vs the reversible hydrogen electrode, qualitatively matching prior reports for Pt nanoparticles. The increase in experimental TOFs as Pt and Rh nanoparticle diameters increase is due to a larger fraction of terraces on larger particles. These findings clarify the structure sensitivity and active site of Pt and Rh for the hydrogenation of phenol and will inform the catalyst design for the hydrogenation of bio-oils.

Structures and Free Energies of Cerium Ions in Acidic Electrolytes.

The Ce3+/Ce4+ redox potential changes with the electrolyte, which could be due to unequal anion complexation free energies between Ce3+ and Ce4+ or a change in the solvent electrostatic screening. Ce complexation with anions and solvent screening also affect the solubility of Ce and charge transfer kinetics for electrochemical reactions involving waste remediation and energy storage. We report the structures and free energies of cerium complexes in seven acidic electrolytes based on Extended X-ray Absorption Fine Structure, UV-vis, and Density Functional Theory calculations. Ce3+ coordinates with nine water molecules as [Ce(H2O)9]3+ in all studied electrolytes. However, Ce4+ complexes with anions in all electrolytes except HClO4. Thus, our results suggest that Ce4+-anion complexation leads to the large shifts in standard redox potential. Long range screening effects are smaller than the anion complexation energies but could be responsible for changes in the Ce solubility with acid.

Investigation of the active sites of rhodium sulfide for hydrogen evolution/oxidation using carbon monoxide as a probe.

Carbon monoxide (CO) was observed to decrease the activity for hydrogen evolution, hydrogen oxidation, and H2-D2 exchange on rhodium sulfide, platinum, and rhodium metal. The temperature at which the CO was desorbed from the catalyst surface (detected by recovery in the H2-D2 exchange activity of the catalyst) was used as a descriptor for the CO binding energy to the active site. The differences in the CO desorption temperature between the different catalysts showed that the rhodium sulfide active site is not metallic rhodium. Using density functional theory, the binding energy of CO to the Rh sites in rhodium sulfide is found comparable to the binding energy on Pt. Coupled with experiment this supports the proposition that rhodium rather than sulfur atoms in the rhodium sulfide are the active site for the hydrogen reaction. This would indicate the active sites for hydrogen evolution/oxidation as well as oxygen reduction (determined by other groups using X-ray absorption spectroscopy) may be the same.

Synthesis of chemicals using solar energy with stable photoelectrochemically active heterostructures.

Efficient and cost-effective conversion of solar energy to useful chemicals and fuels could lead to a significant reduction in fossil hydrocarbon use. Artificial systems that use solar energy to produce chemicals have been reported for more than a century. However the most efficient devices demonstrated, based on traditionally fabricated compound semiconductors, have extremely short working lifetimes due to photocorrosion by the electrolyte. Here we report a stable, scalable design and molecular level fabrication strategy to create photoelectrochemically active heterostructure (PAH) units consisting of an efficient semiconductor light absorber in contact with oxidation and reduction electrocatalysts and otherwise protected by alumina. The functional heterostructures are fabricated by layer-by-layer, template-directed, electrochemical synthesis in porous anodic aluminum oxide membranes to produce high density arrays of electronically autonomous, nanostructured, corrosion resistant, photoactive units (~10(9)-10(10) PAHs per cm(2)). Each PAH unit is isolated from its neighbor by the transparent electrically insulating oxide cellular enclosure that makes the overall assembly fault tolerant. When illuminated with visible light, the free floating devices have been demonstrated to produce hydrogen at a stable rate for over 24 h in corrosive hydroiodic acid electrolyte with light as the only input. The quantum efficiency (averaged over the solar spectrum) for absorbed photons-to-hydrogen conversion was 7.4% and solar-to-hydrogen energy efficiency of incident light was 0.9%. The fabrication approach is scalable for commercial manufacturing and readily adaptable to a variety of earth abundant semiconductors which might otherwise be unstable as photoelectrocatalysts.

Electrode Treatments for Redox Flow Batteries: Translating Our Understanding from Vanadium to Aqueous-Organic.

Redox flow batteries (RFBs) are a promising technology for long-duration energy storage; but they suffer from inefficiencies in part due to the overvoltages at the electrode surface. In this work, more than 70 electrode treatments are reviewed that are previously shown to reduce the overvoltages and improve performance for vanadium RFBs (VRFBs), the most commercialized RFB technology. However, identifying treatments that improve performance the most and whether they are industrially implementable is challenging. This study attempts to address this challenge by comparing treatments under similar operating conditions and accounting for the treatment process complexity. The different treatments are compared at laboratory and industrial scale based on criteria for VRFB performance, treatment stability, economic feasibility, and ease of industrial implementation. Thermal, plasma, electrochemical oxidation, CO2 treatments, as well as Bi, Ag, and Cu catalysts loaded on electrodes are identified as the most promising for adoption in large scale VRFBs. The similarity in electrode treatments for aqueous-organic RFBs (AORFBs) and VRFBs is also identified. The need of standardization in RFBs testing along with fundamental studies to understand charge transfer reactions in redox active species used in RFBs moving forward is emphasized.

Transition metal sulfide hydrogen evolution catalysts for hydrobromic acid electrolysis.

Mixed metal sulfides containing combinations of W, Fe, Mo, Ni, and Ru were synthesized and screened for activity and stability for the hydrogen evolution reaction (HER) in aqueous hydrobromic acid (HBr). Co- and Ni-substituted RuS(2) were identified as potentially active HER electrocatalysts by high-throughput screening (HTS), and the specific compositions Co(0.4)Ru(0.6)S(2) and Ni(0.6)Ru(0.4)S(2) were identified by optimization. Hydrogen evolution activity of Co(0.4)Ru(0.6)S(2) in HBr is greater than RuS(2) or CoS(2) and comparable to Pt and commercial Rh(x)S(y). Structural and morphological characterizations of the Co-substituted RuS(2) suggest that the nanoparticulate solids are a homogeneous solid solution with a pyrite crystal structure. No phase separation is detected for Co substitutions below 30% by X-ray diffraction. In 0.5 M HBr electrolyte, the Co-Ru electrode material synthesized with 30% Co rapidly lost approximately 34% of the initial loading of Co; thereafter, it was observed to exhibit stable activity for HER with no further loss of Co. Density functional theory calculations indicate that the S(2)(2-) sites are the most important for HER and the presence of Co influences the S(2)(2-) sites such that the hydrogen binding energy at sufficiently high hydrogen coverage is decreased compared to ruthenium sulfide. Although showing high HER activity in a flow cell, the reverse reaction of hydrogen oxidation is slow on the RuS(2) catalysts tested when compared to platinum and rhodium sulfide, leaving rhodium sulfide as the only suitable tested material for a regenerative HBr cell due its stability compared to platinum.

Translating Catalyst-Polymer Composites from Liquid to Gas-Fed CO2 Electrolysis: A CoPc-P4VP Case Study.

The electrochemical CO2 reduction reaction (CO2RR) in gas-fed flow electrolyzers using gas diffusion electrodes (GDEs) generates industrially relevant activities and provides a promising approach for carbon recycling. Developing effective catalyst systems on GDEs is critical for achieving high activities. Catalyst-polymer composites (CPCs) formed between immobilized molecular catalysts and coordinating polymers exhibit positive synergies for the enhancement of CO2RR activity. However, previous studies of CPCs have been primarily confined to liquid reaction platforms, and there are few examples of translating CPCs to GDE architectures. This suggests a knowledge gap exists in translating between the two platforms. Herein, we identify and bridge that gap by demonstrating a case study for the (poly-4-vinylpyridine)-encapsulated cobalt phthalocyanine (CoPc-P4VP) CPC. We identify a major knolwedge gap in the overlooked factor of CPC's hydrophobicity, which plays a significant role in gas-fed CO2RR but is often neglected in fundamental studies conducted on the liquid reaction platform. We bridge this gap by correlating catalyst hydrophobicity in liquid CO2RR with activity in gas-fed CO2RR by means of water contact angle measurements. Our case study underscores the importance of incorporating an engineering perspective into CPC studies and the necessity to consider hydrophobicity in CPC design and evaluation. This approach will hopefully accelerate the applied studies of this group of promising catalytic materials in gas-fed CO2 electrolysis.

Unveiling the Cerium(III)/(IV) Structures and Charge-Transfer Mechanism in Sulfuric Acid.

The Ce3+/Ce4+ redox couple has a charge transfer (CT) with extreme asymmetry and a large shift in redox potential depending on electrolyte composition. The redox potential shift and CT behavior are difficult to understand because neither the cerium structures nor the CT mechanism are well understood, limiting efforts to improve the Ce3+/Ce4+ redox kinetics in applications such as energy storage. Herein, we identify the Ce3+ and Ce4+ structures and CT mechanism in sulfuric acid via extended X-ray absorption fine structure spectroscopy (EXAFS), kinetic measurements, and density functional theory (DFT) calculations. We show EXAFS evidence that confirms that Ce3+ is coordinated by nine water molecules and suggests that Ce4+ is complexed by water and three bisulfates in sulfuric acid. Despite the change in complexation within the first coordination shell between Ce3+ and Ce4+, we show that the kinetics are independent of the electrode, suggesting outer-sphere electron-transfer behavior. We identify a two-step mechanism where Ce4+ exchanges the bisulfate anions with water in a chemical step followed by a rate-determining electron transfer step that follows Marcus theory (MT). This mechanism is consistent with all experimentally observed structural and kinetic data. The asymmetry of the Ce3+/Ce4+ CT and the observed shift in the redox potential with acid is explained by the addition of the chemical step in the CT mechanism. The fitted parameters from this rate law qualitatively agree with DFT-predicted free energies and the reorganization energy. The combination of a two-step mechanism with MT should be considered for other metal ion CT reactions whose kinetics have not been appropriately described.

Liquid-Phase Effects on Adsorption Processes in Heterogeneous Catalysis.

Aqueous solvation free energies of adsorption have recently been measured for phenol adsorption on Pt(111). Endergonic solvent effects of ∼1 eV suggest solvents dramatically influence a metal catalyst's activity with significant implications for the catalyst design. However, measurements are indirect and involve adsorption isotherm models, which potentially reduces the reliability of the extracted energy values. Computational, implicit solvation models predict exergonic solvation effects for phenol adsorption, failing to agree with measurements even qualitatively. In this study, an explicit, hybrid quantum mechanical/molecular mechanical approach for computing solvation free energies of adsorption is developed, solvation free energies of phenol adsorption are computed, and experimental data for solvation free energies of phenol adsorption are reanalyzed using multiple adsorption isotherm models. Explicit solvation calculations predict an endergonic solvation free energy for phenol adsorption that agrees well with measurements to within the experimental and force field uncertainties. Computed adsorption free energies of solvation of carbon monoxide, ethylene glycol, benzene, and phenol over the (111) facet of Pt and Cu suggest that liquid water destabilizes all adsorbed species, with the largest impact on the largest adsorbates.

Near-Quantitative Predictions of the First-Shell Coordination Structure of Hydrated First-Row Transition Metal Ions Using K-Edge X-ray Absorption Near-Edge Spectroscopy.

The solvation structure of transition metal ions is important for applications in geochemistry, biochemistry, energy storage, and environmental chemistry. We study the X-ray absorption pre-edge and near-edge spectra at the K-edge of a nearly complete series of hydrated first-row transition metal ions with d orbital occupancy from d2 to d10. We optimize all of the structures at the density functional theory (DFT) level with explicit solvation and then compute the pre-edge X-ray absorption spectra with time-dependent DFT (TDDFT) and restricted active space second-order perturbation theory (RASPT2). TDDFT provides accurate results for spectra that are dominated by single excitations, while RASPT2 correctly distinguishes between singly and doubly excited states with quantitative accuracy compared with experiment. We analyze the pre-edge features for each metal ion to reveal the impact of the variations in d orbital occupancy on the first-shell coordination environment. We also report the lowest-energy ligand field d-d transitions using complete active space second-order perturbation theory.

Why halides enhance heterogeneous metal ion charge transfer reactions.

The reaction kinetics of many metal redox couples on electrode surfaces are enhanced in the presence of halides (i.e., Cl-, Br-, I-). Using first-principles metadynamics simulations, we show a correlation between calculated desorption barriers of V3+-anion complexes bound to graphite via an inner-sphere anion bridge and experimental V2+/V3+ kinetic measurements on edge plane pyrolytic graphite in H2SO4, HCl, and HI. We extend this analysis to V2+/V3+, Cr2+/Cr3+, and Cd0/Cd2+ reactions on a mercury electrode and demonstrate that reported kinetics in acidic electrolytes for these redox couples also correlate with the predicted desorption barriers of metal-anion complexes. Therefore, the desorption barrier of the metal-anion surface intermediate is a descriptor of kinetics for many metal redox couple/electrode combinations in the presence of halides. Knowledge of the metal-anion surface intermediates can guide the design of electrolytes and electrocatalysts with faster kinetics for redox reactions of relevance to energy and environmental applications.

Earth-Abundant Tin Sulfide-Based Photocathodes for Solar Hydrogen Production.

Tin-based chalcogenide semiconductors, though attractive materials for photovoltaics, have to date exhibited poor performance and stability for photoelectrochemical applications. Here, a novel strategy is reported to improve performance and stability of tin monosulfide (SnS) nanoplatelet thin films for H2 production in acidic media without any use of sacrificial reagent. P-type SnS nanoplatelet films are coated with the n-CdS buffer layer and the TiO2 passivation layer to form type II heterojunction photocathodes. These photocathodes with subsequent deposition of Pt nanoparticles generate a photovoltage of 300 mV and a photocurrent density of 2.4 mA cm-2 at 0 V versus reversible hydrogen electrode (RHE) for water splitting under simulated visible-light illumination (λ > 500 nm, Pin = 80 mW cm-2). The incident photon-to-current efficiency at 0 V versus RHE for H2 production reach a maximum of 12.7% at 575 nm with internal quantum efficiency of 13.8%. The faradaic efficiency for hydrogen evolution remains close to unity after 6000 s of illumination, confirming the robustness of the heterojunction for solar H2 production.

On the plasmonic photovoltaic.

The conversion of sunlight into electricity by photovoltaics is currently a mature science and the foundation of a lucrative industry. In conventional excitonic solar cells, electron-hole pairs are generated by light absorption in a semiconductor and separated by the "built in" potential resulting from charge transfer accompanying Fermi-level equalization either at a p-n or a Schottky junction, followed by carrier collection at appropriate electrodes. Here we report a stable, wholly plasmonic photovoltaic device in which photon absorption and carrier generation take place exclusively in the plasmonic metal. The field established at a metal-semiconductor Schottky junction separates charges. The negative carriers are high-energy (hot) electrons produced immediately following the plasmon's dephasing. Some of the carriers are energetic enough to clear the Schottky barrier or quantum mechanically tunnel through it, thereby producing the output photocurrent. Short circuit photocurrent densities in the range 70-120 µA cm(-2) were obtained for simulated one-sun AM1.5 illumination with devices based on arrays of parallel gold nanorods, conformally coated with 10 nm TiO2 films and fashioned with a Ti metal collector. For the device with short circuit currents of 120 µA cm(-2), the internal quantum efficiency is ∼2.75%, and its wavelength response tracks the absorption spectrum of the transverse plasmon of the gold nanorods indicating that the absorbed photon-to-electron conversion process resulted exclusively in the Au, with the TiO2 playing a negligible role in charge carrier production. Devices fabricated with 50 nm TiO2 layers had open-circuit voltages as high as 210 mV, short circuit current densities of 26 µA cm(-2), and a fill factor of 0.3. For these devices, the TiO2 contributed a very small but measurable fraction of the charge carriers.

An autonomous photosynthetic device in which all charge carriers derive from surface plasmons.

Solar conversion to electricity or to fuels based on electron-hole pair production in semiconductors is a highly evolved scientific and commercial enterprise. Recently, it has been posited that charge carriers either directly transferred from the plasmonic structure to a neighbouring semiconductor (such as TiO2) or to a photocatalyst, or induced by energy transfer in a neighbouring medium, could augment photoconversion processes, potentially leading to an entire new paradigm in harvesting photons for practical use. The strong dependence of the wavelength at which the local surface plasmon can be excited on the nanostructure makes it possible, in principle, to design plasmonic devices that can harvest photons over the entire solar spectrum and beyond. So far, however, most such systems show rather small photocatalytic activity in the visible as compared with the ultraviolet. Here, we report an efficient, autonomous solar water-splitting device based on a gold nanorod array in which essentially all charge carriers involved in the oxidation and reduction steps arise from the hot electrons resulting from the excitation of surface plasmons in the nanostructured gold. Each nanorod functions without external wiring, producing 5 × 10(13) H2 molecules per cm(2) per s under 1 sun illumination (AM 1.5 and 100 mW cm(-2)), with unprecedented long-term operational stability.