The Placenta in Congenital Langerhans Cell Histiocytosis: A Case Report of Unusual Involvement of Chorionic Plate and Umbilical Vein.

The congenital presentation of Langerhans cell histiocytosis (LCH) is a rare presentation of an uncommon neoplastic process. Concurrent placental parenchymal involvement is even more rare, with just 2 cases of congenital multisystem LCH with placental involvement reported in English medical literature thus far. Here, we present a case of a liveborn male born at 37-weeks, 6-day gestation with congenital LCH focally involving the placenta. Langerhans cells were identified in an area of the placenta showing an unusual mononuclear cell infiltrate in the wall of the umbilical vein. Langerhans cells were also focally identified in areas of chronic villitis, as well as normal-appearing chorionic plate. The examination of the placenta in cases of clinical suspicion of LCH can be of paramount importance since it may provide the early diagnostic evidence of LCH. In this context, placental involvement by LCH should be considered even in the absence of abnormal histology.

Analysis of menstrual effluent: diagnostic potential for endometriosis.

BACKGROUND: Endometriosis is a chronic and underdiagnosed disease which affects 5-10% of women of childbearing age and is characterized by growth of endometrial tissue outside of the uterus, most often in the peritoneal cavity. Delay in diagnosis is a major problem for management of this disorder, and treatment is often not initiated until the disease has progressed for many years. Although the exact etiology of endometriosis remains unknown, retrograde menstruation is recognized as a common underlying factor leading to the deposit of menstrual effluent (ME) into the peritoneal cavity. Differences in the cellular biology and genetics of the cells within ME are therefore likely to explain why endometriosis develops in only a subset of women. METHODS: Patients with and without endometriosis were consented to provide ME. ME was analyzed by flow cytometry for CD45- and CD45+ cell populations or used to isolate stromal fibroblast cells. ME-derived stromal fibroblast cells were assessed using decidualization assays following the addition of cAMP and IGFBP-1 concentrations in the culture supernatants were measured by ELISA. In addition, RNA was collected and analyzed by RNA-Seq and qPCR for markers of decidualization and to identify differentially expressed genes in ME-derived stromal fibroblast cells obtained from controls and subjects with endometriosis (±cAMP). RESULTS: Flow cytometry analysis of cell subsets within the CD45+ fraction of ME revealed a significant decrease in the number of uterine NK cells in endometriosis patients compared with controls (p < 0.01). No other significant differences within either the CD45+ or CD45- cell populations were observed. Most strikingly, ME-derived stromal fibroblast cells cultured from endometriosis subjects showed impaired decidualization potential compared with controls. Highly significant differences in decidualization response were detected by measuring IGFBP-1 production at multiple time points after cAMP stimulation (p = 0.0025 at 6 h; p = 0.0045 at 24 h; p = 0.0125 at 48 h). RNA-Seq and qPCR analyses were used to identify genes differentially expressed by ME-derived stromal fibroblast cells obtained from endometriosis and control subjects. CONCLUSIONS: Menstrual effluent can be useful for investigating the pathobiology of endometriosis and for developing a non-invasive diagnostic for endometriosis which may lead to earlier and more effective treatments for this common disorder.

Prevalence and incidence of dementia among indigenous populations: a systematic review.

BACKGROUND: Indigenous populations may be at increased risk, compared with majority populations, for the development of dementia due to lower education levels and socio-economic status, higher rates of diabetes, hypertension, cardiovascular disease and alcohol abuse, an aging population structure, and poorer overall health. This is the first systematic review investigating the prevalence and incidence of dementia in indigenous populations worldwide. METHODS: This systematic review was conducted in accordance with PRISMA guidelines. We searched MEDLINE, Embase, and PsycInfo for relevant papers published up to April 2015. Studies were included if they reported prevalence or incidence, the disease typically occurred after the age of 45, the study population included indigenous people, and the study was conducted in the general population. RESULTS: Fifteen studies representing five countries (Canada, Australia, the USA, Guam, Brazil) met the inclusion criteria. Dementia prevalence ranged from 0.5% to 20%. Retrospective studies relying on medical records for diagnoses had much lower prevalence rates and a higher risk of bias than population-based prospective studies performing their own diagnoses with culturally appropriate cognitive assessment methods. CONCLUSIONS: The prevalence of dementia among indigenous populations appears to be higher than it is for non-indigenous populations. Despite a building body of evidence supporting the need for dementia research among indigenous populations, there is a paucity of epidemiological research, none of which is of high quality.

Growing human-scale scala tympani-likein vitrocell constructs.

Emerging materials and electrode technologies have potential to revolutionise development of higher resolution next-generation, bionic devices. However, barriers associated with the extended timescales, regulatory constraints, and opportunity costs of preclinical and clinical studies, can inhibit such innovation. Development ofin vitromodels that mimic human tissues would provide an enabling platform to overcome many of these barriers in the product development pathway. This research aimed to develop human-scale tissue engineered cochlea models for high throughput evaluation of cochlear implants on the bench. Novel mould-casting techniques and stereolithography three-dimensional (3D) printing approaches to template hydrogels into spiral-shaped structures resembling the scala tympani were compared. While hydrogels are typically exploited to support 3D tissue-like structures, the challenge lies in developing irregular morphologies like the scala tympani, in which the cochlear electrodes are commonly implanted. This study successfully developed human-scale scala tympani-like hydrogel structures that support viable cell adhesion and can accommodate cochlear implants for future device testing.

Emerging trends in the development of flexible optrode arrays for electrophysiology.

Optical-electrode (optrode) arrays use light to modulate excitable biological tissues and/or transduce bioelectrical signals into the optical domain. Light offers several advantages over electrical wiring, including the ability to encode multiple data channels within a single beam. This approach is at the forefront of innovation aimed at increasing spatial resolution and channel count in multichannel electrophysiology systems. This review presents an overview of devices and material systems that utilize light for electrophysiology recording and stimulation. The work focuses on the current and emerging methods and their applications, and provides a detailed discussion of the design and fabrication of flexible arrayed devices. Optrode arrays feature components non-existent in conventional multi-electrode arrays, such as waveguides, optical circuitry, light-emitting diodes, and optoelectronic and light-sensitive functional materials, packaged in planar, penetrating, or endoscopic forms. Often these are combined with dielectric and conductive structures and, less frequently, with multi-functional sensors. While creating flexible optrode arrays is feasible and necessary to minimize tissue-device mechanical mismatch, key factors must be considered for regulatory approval and clinical use. These include the biocompatibility of optical and photonic components. Additionally, material selection should match the operating wavelength of the specific electrophysiology application, minimizing light scattering and optical losses under physiologically induced stresses and strains. Flexible and soft variants of traditionally rigid photonic circuitry for passive optical multiplexing should be developed to advance the field. We evaluate fabrication techniques against these requirements. We foresee a future whereby established telecommunications techniques are engineered into flexible optrode arrays to enable unprecedented large-scale high-resolution electrophysiology systems.

Combining submerged electrospray and UV photopolymerization for production of synthetic hydrogel microspheres for cell encapsulation.

Microencapsulation within hydrogel microspheres holds much promise for drug and cell delivery applications. Synthetic hydrogels have many advantages over more commonly used natural materials such as alginate, however their use has been limited due to a lack of appropriate methods for manufacturing these microspheres under conditions compatible with sensitive proteins or cells. This study investigated the effect of flow rate and voltage on size and uniformity of the hydrogel microspheres produced via submerged electrospray combined with UV photopolymerization. In addition, the mechanical properties and cell survival within microspheres was studied. A poly(vinyl alcohol) (PVA) macromer solution was sprayed in sunflower oil under flow rates between 1-100 µL/min and voltages 0-10 kV. The modes of spraying observed were similar to those previously reported for electrospraying in air. Spheres produced were smaller for lower flow rates and higher voltages and mean size could be tailored from 50 to 1,500 µm. The microspheres exhibited a smooth, spherical morphology, did not aggregate and the compressive modulus of the spheres (350 kPa) was equivalent to bulk PVA (312 kPa). Finally, L929 fibroblasts were encapsulated within PVA microspheres and showed viability >90% after 24 h. This process shows great promise for the production of synthetic hydrogel microspheres, and specifically supports encapsulation of cells.

Impedance Properties of Multi-Optrode Biopotential Sensing Arrays.

Recording and monitoring electrically-excitable cells is critical to understanding the complex cellular networking within organs as well as the processes underlying many electro-physiological pathologies. Biopotential recording using an optical-electrode (optrode) is a novel approach which has potential to significantly improve interface-instrumentation impedance mismatching as recording contact-sizes become smaller and smaller. Optrodes incorporate a conductive interface that can sense extracellular potential and an underlying layer of liquid crystals that passively transduces electrical signals into measurable optical signals. This study investigates the impedance properties of this optical technology by varying the diameter of recording sites and observing the corresponding changes in the impedance values. The results show that the liquid crystals in this optrode platform exhibit input impedance values (1 MΩ - 100 GΩ) that are three orders of magnitude higher than the corresponding interface impedance, which is appropriate for voltage sensing. The automatic scaling of the input impedance enabled within the optrode system maintains a relatively constant ratio between input and total system impedance of about one for sensing areas with diameters ranging from 40 µm to 1 mm, at which the calculated signal loss is predicted to be <1%. This feature preserves the interface-transducer impedance ratio, regardless of the size of the recording site, allowing development of passive optrode arrays capable of very high spatial-resolution recordings.

Electromechanical Stability and Transmission Behavior of Transparent Conductive Films for Biomedical Optoelectronic Devices.

The application of transparent conductive films to flexible biomedical optoelectronics is limited by stringent requirements on the candidate materials' electromechanical and optical properties as well as their biological performance. Thin films of graphene and poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) are sought as mechanically flexible alternatives to traditional indium tin oxide (ITO). However, they require more understanding of their suitability for biomedical optoelectronic devices in terms of transmission behavior and electromechanical stability. This study shows that the relative increase in sheet resistance under cyclic loading for ITO, graphene, and PEDOT:PSS was 3546±3908%,12±2.7%, and 62±68%, respectively. Moreover, graphene and PEDOT:PSS showed a transmission uniformity of 9.3% and 36.3% (380-2000 nm), respectively, compared with ITO film (61%). Understanding the optical, electrical, and mechanical limits of the transparent conductive films facilitates the optimization of flexible optoelectronic designs to fit multiple biomedical research and clinical applications.

Challenges and solutions for fabrication of three-dimensional cocultures of neural cell-loaded biomimetic constructs.

Fabrication of three-dimensional (3D) constructs to model body tissues and organs can contribute to research into tissue development and models for studying disease, as well as supporting preclinical drug screening in vitro. Furthermore, 3D constructs can also be used for diagnosis and therapy of disease conditions via lab on a chip and microarrays for diagnosis and engineered products for tissue repair, replacement, and regeneration. While cell culture approaches for studying tissue development and disease in two dimensions are long-established, the translation of this knowledge into 3D environments remains a fertile field of research. In this Tutorial, we specifically focus on the application of biosynthetic hydrogels for neural cell encapsulation. The Tutorial briefly covers background on using biosynthetic hydrogels for cell encapsulation, as well as common fabrication techniques. The Methods section focuses on the hydrogel design and characterization, highlighting key elements and tips for more effective approaches. Coencapsulation of different cell types, and the challenges associated with different growth and maintenance requirements, is the main focus of this Tutorial. Much care is needed to blend different cell types, and this Tutorial provides tips and insights that have proven successful for 3D coculture in biosynthetic hydrogels.

Conducting polymer-hydrogels for medical electrode applications.

Conducting polymers hold significant promise as electrode coatings; however, they are characterized by inherently poor mechanical properties. Blending or producing layered conducting polymers with other polymer forms, such as hydrogels, has been proposed as an approach to improving these properties. There are many challenges to producing hybrid polymers incorporating conducting polymers and hydrogels, including the fabrication of structures based on two such dissimilar materials and evaluation of the properties of the resulting structures. Although both fabrication and evaluation of structure-property relationships remain challenges, materials comprised of conducting polymers and hydrogels are promising for the next generation of bioactive electrode coatings.

Subthreshold Electrical Stimulation for Controlling Protein-Mediated Impedance Increases in Platinum Cochlear Electrode.

OBJECTIVE: This study evaluated subthreshold biphasic stimulation pulses as a strategy to stabilize electrode impedance via control of protein adsorption. Following implantation, cochlear electrodes undergo impedance fluctuations thought to be caused by protein adsorption and/or inflammatory responses. Impedance increases can impact device power consumption, safe charge injection limits, and long-term stability of electrodes. METHODS: Protein-mediated changes in polarization impedance (Zp) were measured by voltage transient responses to biphasic current pulses and electrochemical impedance spectroscopy, with and without protein solutions. Four subthreshold stimulation regimes were studied to assess their effects on protein adsorption and impedance; (1) symmetric charge-balanced pulses delivered continuously, (2) at 10% duty cycle, (3) at 1% duty cycle, and (4) an asymmetric charge balanced pulse delivered continuously with a cathodic phase twice as long as the anodic phase. RESULTS: The Zp of electrodes incubated in protein solutions without stimulation for 2 h increased by between ∼28% and ∼55%. Subthreshold stimulation reduced the rate at which impedance increased following exposure to all protein solutions. Decreases in Zp were dependent on the type of protein solution and the stimulation regime. Subthreshold stimulation pulses were more effective when delivered continuously compared to 1% and 10% duty cycles. CONCLUSION: These results support the potential of subthreshold stimulation pulses to mitigate protein-mediated increase in impedance. SIGNIFICANCE: This research highlights the potential of clinically translatable stimulation pulses to mitigate perilymph protein adsorption on cochlear electrodes, a key phenomenon precursor of the inflammatory response.

Electrochemical and biological performance of chronically stimulated conductive hydrogel electrodes.

OBJECTIVE: Evaluate electrochemical properties, biological response, and surface characterization of a conductive hydrogel (CH) coating following chronic in vivo stimulation. APPROACH: Coated CH or uncoated smooth platinum (Pt) electrode arrays were implanted into the cochlea of rats and stimulated over a 5 week period with more than 57 million biphasic current pulses. Electrochemical impedance spectroscopy (EIS), charge storage capacity (CSC), charge injection limit (CIL), and voltage transient (VT) impedance were measured on the bench before and after stimulation, and in vivo during the stimulation program. Electrically-evoked auditory brainstem responses were recorded to monitor neural function. Following explant, the cochleae were examined histologically and electrodes were examined using scanning electron microscopy. MAIN RESULTS: CH coated electrodes demonstrated a bench-top electrochemical advantage over Pt electrodes before and after the electrical stimulation program. In vivo, CH coated electrodes also had a significant advantage over Pt electrodes throughout the stimulation program, exhibiting higher CSC (p= 0.002), larger CIL (p = 0.002), and lower VT impedance (p < 0.001). The CH cohort exhibited a greater tissue response (p= 0.003) with small deposits of particulate material within the tissue capsule. There was no loss in auditory neuron density or change in neural response thresholds in any cochleae. Examination of the electrode surface revealed that most CH electrodes exhibited some coating loss; however, there was no evidence of corrosion in the underlying Pt. SIGNIFICANCE: CH coated electrodes demonstrated significant electrochemical advantages on the bench-top and in vivo and maintained neural function despite an increased tissue response and coating loss. While further research is required to understand the cause of the coating loss, CH electrodes provide promise for use in neural prostheses.

Network structure and macromolecular drug release from poly(vinyl alcohol) hydrogels fabricated via two crosslinking strategies.

Injectable hydrogels have potential biomedical applications ranging from tissue fillers to drug delivery vehicles. This study focussed on evaluating the structure of poly(vinyl alcohol) (PVA) hydrogels of variable solid content and high molecular weight model drug release from the networks formed via either conventional photo-polymerization compared with chemical initiation of polymerization using an oxidation-reduction (redox) reaction. Swelling behaviour was characterised in water to assess the structural properties. Model drugs, FITC-Dextran, 20 kDa (FD20) and 4 kDa (FD4) were loaded in the hydrogels prior to curing and drug release studies conducted. Redox-cured hydrogels were more swollen than UV-cured systems, lost approximately 20% of their polymer mass compared to only 5% from UV-cured hydrogels and subsequently exhibited networks of larger mesh sizes. Also, networks of variable solid contents showed different structural properties with systems of higher polymer concentration exhibiting a smaller mesh size. The difference in structural properties of the networks affected release of FD20, being faster in redox-cured than UV-cured hydrogels, and slower from systems of higher solid content. Release of FD4 was faster than FD20 from networks of same solid content. This study suggested that PVA hydrogels can be cured by redox-initiation to function as a controlled delivery system for macromolecular drugs.

Tissue engineered hydrogels supporting 3D neural networks.

Promoting nerve regeneration requires engineering cellular carriers to physically and biochemically support neuronal growth into a long lasting functional tissue. This study systematically evaluated the capacity of a biosynthetic poly(vinyl alcohol) (PVA) hydrogel to support growth and differentiation of co-encapsulated neurons and glia. A significant challenge is to understand the role of the dynamic degradable hydrogel mechanical properties on expression of relevant cellular morphologies and function. It was hypothesised that a carrier with mechanical properties akin to neural tissue will provide glia with conditions to thrive, and that glia in turn will support neuronal survival and development. PVA co-polymerised with biological macromolecules sericin and gelatin (PVA-SG) and with tailored nerve tissue-like mechanical properties were used to encapsulate Schwann cells (SCs) alone and subsequently a co-culture of SCs and neural-like PC12s. SCs were encapsulated within two PVA-SG gel variants with initial compressive moduli of 16 kPa and 2 kPa, spanning a range of reported mechanical properties for neural tissues. Both hydrogels were shown to support cell viability and expression of extracellular matrix proteins, however, SCs grown within the PVA-SG with a higher initial modulus were observed to present with greater physiologically relevant morphologies and increased expression of extracellular matrix proteins. The higher modulus PVA-SG was subsequently shown to support development of neuronal networks when SCs were co-encapsulated with PC12s. The lower modulus hydrogel was unable to support effective development of neural networks. This study demonstrates the critical link between hydrogel properties and glial cell phenotype on development of functional neural tissues. STATEMENT OF SIGNIFICANCE: Hydrogels as platforms for tissue regeneration must provide encapsulated cellular progenitors with physical and biochemical cues for initial survival and to support ongoing tissue formation as the artificial network degrades. While most research focuses on tailoring scaffold properties to suit neurons, this work aims to support glia SCs as the key cellular component that physically and biochemically supports the neuronal network. The challenge is to modify hydrogel properties to support growth and development of multiple cell types into a neuronal network. Given SCs ability to respond to substrate mechanical properties, the significance of this work lies in understanding the relationship between dynamic hydrogel mechanical properties and glia SCs development as the element that enables formation of mature, differentiated neural networks.

Electrochemical and mechanical performance of reduced graphene oxide, conductive hydrogel, and electrodeposited Pt-Ir coated electrodes: an active in vitro study.

OBJECTIVE: To systematically compare the in vitro electrochemical and mechanical properties of several electrode coatings that have been reported to increase the efficacy of medical bionics devices by increasing the amount of charge that can be delivered safely to the target neural tissue. APPROACH: Smooth platinum (Pt) ring and disc electrodes were coated with reduced graphene oxide, conductive hydrogel, or electrodeposited Pt-Ir. Electrodes with coatings were compared with uncoated smooth Pt electrodes before and after an in vitro accelerated aging protocol. The various coatings were compared mechanically using the adhesion-by-tape test. Electrodes were stimulated in saline for 24 hours/day 7 days/week for 21 d at 85 °C (1.6-year equivalence) at a constant charge density of 200 µC/cm2/phase. Electrodes were graded on surface corrosion and trace analysis of Pt in the electrolyte after aging. Electrochemical measurements performed before, during, and after aging included electrochemical impedance spectroscopy, cyclic voltammetry, and charge injection limit and impedance from voltage transient recordings. MAIN RESULTS: All three coatings adhered well to smooth Pt and exhibited electrochemical advantage over smooth Pt electrodes prior to aging. After aging, graphene coated electrodes displayed a stimulation-induced increase in impedance and reduction in the charge injection limit (p  < 0.001), alongside extensive corrosion and release of Pt into the electrolyte. In contrast, both conductive hydrogel and Pt-Ir coated electrodes had smaller impedances and larger charge injection limits than smooth Pt electrodes (p  < 0.001) following aging regardless of the stimulus level and with little evidence of corrosion or Pt dissolution. SIGNIFICANCE: This study rigorously tested the mechanical and electrochemical performance of electrode coatings in vitro and provided suitable candidates for future in vivo testing.

Conducting polymers for neural interfaces: challenges in developing an effective long-term implant.

Metal electrode materials used in active implantable devices are often associated with poor long-term stimulation and recording performance. Modification of these materials with conducting polymer coatings has been suggested as an approach for improving the neural tissue-electrode interface and increasing the effective lifetime of these implants. Neural interfaces ideally have intimate contact between the excitable tissue and the electrode to maintain signal quality and activation of neural cells. The outcomes of current research into conducting polymers as coatings has potential to enhance this tissue-material contact by increasing the electrode surface area and roughness as well as allowing delivery of bioactive signals to neural cells. However, challenges facing conducting polymers include poor electroactive stability and mechanical properties as well as control of the mobility, concentration and presentation of bioactive molecules. The impact of biological inclusions on polymer properties and their ongoing performance in neural prosthetics requires a greater understanding with future research aimed at controlling and optimising film characteristics for long-term performance. Optimising the electrode interface will require a trade-off between desired electrical, mechanical, chemical and biological properties.

Synthesis and characterization of radiopaque iodine-containing degradable PVA hydrogels.

Poly (vinyl alcohol) (PVA) hydrogels are highly attractive for biomedical applications, especially for controlled release of drugs and proteins. Recently, degradable PVA hydrogels have been described, having the advantage that the material disappears over time from the implantation site. Herein, we report the synthesis of radiopaque degradable PVA, which gives a further advantage that the position of the hydrogel can precisely be determined by X-ray fluoroscopy. Radiopacity has been introduced by replacing 0.5% of the pendent alcohol groups on the PVA with 4-iodobenzoylchloride. This level of substitution rendered the polymer adequately radiopaque. The subsequent modification of 0.8% of the pendent hydroxyl groups with an ester acrylate functional group allowed for cross-linking of the macromers. The radiopaque hydrogels degraded over a time span of 140 days. Rheology data suggested that the macromer solutions were appropriate for injection.

The effect of redox polymerisation on degradation and cell responses to poly (vinyl alcohol) hydrogels.

Biocompatible, degradable hydrogel systems that can cure in situ following injection as a liquid are useful as a base for tissue engineering and drug delivery. In this study, poly (vinyl alcohol) (PVA) polymers were modified with degradable crosslinkers and formulated for either ultraviolet (UV) light initiation or chemical initiation using an oxidation/reduction (redox) curing method. A major objective was to compare the properties of degradable PVA hydrogels formed via two routes of curing. The effect of macromer concentration, degree of hydrolysis and functional group density on the degradation profiles was investigated. Also, since the hydrogels have been designed to be injected as a liquid for in situ curing, the effect of modified macromer solutions and degradation products on cell growth was investigated. Total degradation times ranged from approximately 20 days up to 120 days and increased in direct proportion with percent macromer. Initiation method (UV or redox) did not significantly impact on time for total degradation. While aqueous solutions of the modified macromer induced some cell growth inhibition, mainly associated with oxidative solutions, degradation products showed relatively low cell growth inhibition. Degradable PVA hydrogels tailored to produce networks with various degradation profiles can be cured by redox initiation and have potential as injectable polymers for soft-tissue engineering and drug delivery.

Mechanisms for Imparting Conductivity to Nonconductive Polymeric Biomaterials.

Traditionally, conductive materials for electrodes are based on high modulus metals or alloys. Development of bioelectrodes that mimic the mechanical properties of the soft, low modulus tissues in which they are implanted is a rapidly expanding field of research. Many polymers exist that more closely match tissue mechanics than metals; however, the majority do not conduct charge. Integrating conductive properties via incorporation of metals and other conductors into nonconductive polymers is a successful approach to producing polymers that can be used in electrical interfacing devices. When combining conductive materials with nonconductive polymer matrices, there is often a tradeoff between the electrical and mechanical properties. This review analyzes the advantages and disadvantages of approaches involving coating or layer formation, composite formation via dispersion of conductive inclusions through polymer matrices, and in situ growth of a conductive network within polymers.

A comparative study of enzyme initiators for crosslinking phenol-functionalized hydrogels for cell encapsulation.

BACKGROUND: Dityrosine crosslinking in proteins is a bioinspired method of forming hydrogels. This study compares oxidative enzyme initiators for their relative crosslinking efficiency and cytocompatibility using the same phenol group and the same material platform. Four common enzyme and enzyme-like oxidative initiators were probed for resulting material properties and cell viability post-encapsulation. RESULTS: All four initiators can be used to form phenol-crosslinked hydrogels, however gelation rates are dependent on enzyme type, concentration, and the oxidant. Horseradish peroxidase (HRP) or hematin with hydrogen peroxide led to a more rapid poly (vinyl alcohol)-tyramine (PVA-Tyr) polymerization (10-60 min) because a high oxidant concentration was dissolved within the macromer solution at the onset of crosslinking, whereas laccase and tyrosinase require oxygen diffusion to crosslink phenol residues and therefore took longer to gel (2.5+ hours). The use of hydrogen peroxide as an oxidant reduced cell viability immediately post-encapsulation. Laccase- and tyrosinase-mediated encapsulation of cells resulted in higher cell viability immediately post-encapsulation and significantly higher cell proliferation after one week of culture. CONCLUSIONS: Overall this study demonstrates that HRP/H2O2, hematin/H2O2, laccase, and tyrosinase can create injectable, in situ phenol-crosslinked hydrogels, however oxidant type and concentration are critical parameters to assess when phenol crosslinking hydrogels for cell-based applications.