Impact of three-dimensional-printing technology guidance on surgical outcomes for retroperitoneal sarcoma: A propensity score-matched study.

BACKGROUND: The surgical treatment of retroperitoneal sarcoma (RPS) is highly challenging because of its complex anatomy. In this study, the authors compared the surgical outcomes of patients with RPS who underwent surgical resection guided by three-dimensional (3D) printing technology versus traditional imaging. METHODS: This retrospective study included 251 patients who underwent RPS resection guided by 3D-printing technology or traditional imaging from January 2019 to December 2022. The main outcome measures were operative time, intraoperative blood loss, postoperative complications, and hospital stay. RESULTS: In total, 251 patients were enrolled in the study: 46 received 3D-printed navigation, and 205 underwent traditional surgical methods. Propensity score matching yielded 44 patients in the 3D group and 82 patients in the control group. The patients' demographics and tumor characteristics were comparable in the matched cohorts. The 3D group had significantly shorter operative time (median, 186.5 minutes [interquartile range (IQR), 130.0-251.3 minutes] vs. 210.0 minutes [IQR, 150.8-277.3 minutes]; p = .04), less intraoperative blood loss (median, 300.0 mL [IQR, 100.0-575.0 mL] vs. 375.0 mL [IQR, 200.0-925.0 mL]; p = .02), shorter postoperative hospital stays (median, 11.0 days [IQR, 9.0-13.0 days] vs. 14.0 days [IQR, 10.8-18.3 days]; p = .02), and lower incidence rate of overall postoperative complications than the control group (18.1% vs. 36.6%; p = .03). There were no differences with regard to the intraoperative blood transfusion rate, the R0/R1 resection rate, 30-day mortality, or overall survival. CONCLUSIONS: Patients in the 3D group had favorable surgical outcomes compared with those in the control group. These results suggest that 3D-printing technology might overcome challenges in RPS surgical treatment. PLAIN LANGUAGE SUMMARY: The surgical treatment of retroperitoneal sarcoma (RPS) is highly challenging because of its complex anatomy. The purpose of this study was to investigate whether three-dimensional (3D) printing technology offers advantages over traditional two-dimensional imaging (such as computed tomography and magnetic resonance imaging) for guiding the surgical treatment of RPS. In a group of patients who had RPS, surgery guided by 3D-printing technology was associated with better surgical outcomes, including shorter operative time, decreased blood loss, shorter hospital stays, and fewer postoperative complications. These findings suggested that 3D-printing technology could help surgeons overcome challenges in the surgical treatment of RPS. 3D-printing technology has important prospects in the surgical treatment of RPS.

Application of Three-Dimensional Printing Technology in the Perioperative Management of Cardiac Tumours: A Review and Analysis.

Background: Multimodal imaging plays a crucial role in evaluating suspected cardiac tumours. In recent years, three-dimensional (3D) printing technology has continued to advance such that image-based 3D-printed models have been incorporated into the auxiliary diagnosis and treatment of cardiac tumour diseases. The purpose of this review is to analyze the existing literature on the application of 3D printing in cardiac tumour surgery to examine the current status of the application of this technology. Methods: By searching PubMed, Cochrane, Scopus and Google Scholar, as well as other resource databases, a completed review of the available literature was performed. Effect sizes from published studies were investigated, and results are presented concerning the use of 3D surgical planning in the management of cardiac tumours. Results: According to the reviewed literature, our study comes to the point that 3D printing is a valuable technique for planning surgery for cardiac tumours. As shown in the review report, Mucinous and sarcomatous tumours are the most commonly used tumours for 3D printing, magnetic resonance imaging (MRI) and computed tomography (CT) are the most commonly used technologies for preparing 3D printing models, the main printing technology is stereolithography, and the most used 3D modeling software is Mimics. The printing time and cost required for 3D printing are affected by factors such as the size of the type, complexity, the printed material and the 3D printing technology used. The reported research shows that 3D printing can understand the anatomy of complex tumour cases, virtual surgical simulation, as well as facilitate doctor-patient communication and clinical teaching. Conclusions: These results show that the development of 3D printing technology has brought more accurate and safe perioperative treatment options for patients with cardiac tumours. Therefore, 3D printing technology is expected to become a routine clinical diagnosis and treatment tool for cardiac tumours.

Direct correlation of MR-DWI and histopathology of Wilms' tumours through a patient-specific 3D-printed cutting guide.

OBJECTIVES: The International Society of Paediatric Oncology-Renal Tumour Study Group (SIOP-RTSG) discourages invasive procedures to determine the histology of paediatric renal neoplasms at diagnosis. Therefore, the histological subtype of Wilms' tumours (WT) is unknown at the start of neoadjuvant chemotherapy. MR-DWI shows potential value as a non-invasive biomarker through apparent diffusion coefficients (ADCs). This study aimed to describe MR characteristics and ADC values of paediatric renal tumours to differentiate subtypes. MATERIALS AND METHODS: Children with a renal tumour undergoing surgery within the SIOP-RTSG 2016-UMBRELLA protocol were prospectively included between May 2021 and 2023. In the case of a total nephrectomy, a patient-specific cutting guide based on the neoadjuvant MR was 3D-printed, allowing a correlation between imaging and histopathology. Whole-tumour volumes and ADC values were statistically compared with the Mann-Whitney U-test. Direct correlation on the microscopic slide level was analysed through mixed model analysis. RESULTS: Fifty-nine lesions of 54 patients (58% male, median age 3.0 years (range 0-17.7 years)) were included. Forty-four lesions involved a WT. Stromal type WT showed the lowest median decrease in volume after neoadjuvant chemotherapy (48.1 cm3, range 561.5-(+)332.7 cm3, p = 0.035). On a microscopic slide level (n = 240 slides) after direct correlation through the cutting guide, stromal areas showed a significantly higher median ADC value compared to epithelial and blastemal foci (p < 0.001). With a cut-off value of 1.195 * 10-3 mm2/s, sensitivity, and specificity were 95.2% (95% confidence interval 87.6-98.4%) and 90.5% (95% confidence interval 68.2-98.3%), respectively. CONCLUSION: Correlation between histopathology and MR-DWI through a patient-specific 3D-printed cutting guide resulted in significant discrimination of stromal type WT from epithelial and blastemal subtypes. CLINICAL RELEVANCE STATEMENT: Stromal Wilms' tumours could be discriminated from epithelial- and blastemal lesions based on high apparent diffusion coefficient values and limited decrease in volume after neoadjuvant chemotherapy. This may aid in future decision-making, especially concerning discrimination between low- and high-risk neoplasms. KEY POINTS: MR-DWI shows potential value as a non-invasive biomarker in paediatric renal tumours. The patient-specific cutting guide leads to a correlation between apparent diffusion coefficient values and Wilms' tumour subtype. Stromal areas could be discriminated from epithelial and blastemal foci in Wilms' tumours based on apparent diffusion coefficient values.

Custom three-dimensional printed implants for reconstruction of oncologic pelvic defects.

The use of three-dimensional printed implants in the field of orthopedic surgery has become increasingly popular and has potentiated hip reconstruction in the setting of oncologic resections of the pelvis and acetabulum. In this review, we examine and discuss the indications and technical considerations for custom implant reconstruction of pelvic defects.

Accuracy of non-medical and medical individuals in identifying cerebral cortical abnormality from three-dimensional printed models of magnetic resonance images in children with hypoxic ischemic injury.

Effective communication of imaging findings in term hypoxic ischemic injury to family members, non-radiologist colleagues and members of the legal profession can be extremely challenging through text-based radiology reports. Utilization of three-dimensional (D) printed models, where the actual findings of the brain can be communicated via tactile perception, is a potential solution which has not yet been tested in practice. We aimed to determine the sensitivity and specificity of different groups, comprising trained radiologists, non-radiologist physicians and non-physicians, in the detection of gross disease of the cerebral cortex from 3-D printed brain models derived from magnetic resonance imaging (MRI) scans of children. Ten MRI scans in children of varying ages with either watershed pattern hypoxic ischemic injury (cortical injury) or basal-ganglia-thalamus hypoxic ischemic injury pattern with limited perirolandic cortical abnormalities and 2 normal MRI scans were post processed and 3-D printed. In total, 71 participants reviewed the 12 models and were required to indicate only the brain models that they felt were abnormal (with a moderate to high degree of degree of confidence). The 71 participants included in the study were 38 laypeople (54%), 17 radiographic technologists (24%), 6 nurses (8%), 5 general radiologists (7%), 4 non-radiologist physicians- 3 pediatricians and 1 neurologist (6%) and 1 emergency medical services staff (1%). The sensitivity and specificity for detecting the abnormal brains of the 71 participants were calculated. Radiologists showed the highest sensitivity (72%) and specificity (70%). Non-radiologist physicians had a sensitivity of 67.5% and a specificity of 75%. Nurses had a sensitivity of 70% and a specificity of 41.7%. Laypeople (non-medical trained) had a sensitivity of 56.1% and a specificity of 55.3%. Radiologists' high sensitivity and specificity of 72% and 70%, respectively, validates the accuracy of the 3-D-printed models in reproducing abnormalities from MRI scans. The non-radiologist physicians also had a high sensitivity and specificity. Laypeople, without any prior training or guidance in looking at the models, had a sensitivity of 56.1% and a specificity of 55.3%. These results show the potential for use of the 3-D printed brains as an alternate form of communication for conveying the pathological findings of hypoxic ischemic injury of the brain to laypeople.

3D-printed orthoses and prostheses for people with physical disability in rehabilitation centers: a scoping review.

AIMS: The World Health Organization points out that, by 2030, two billion people will need at least one assistive product. 3D printing can be used to meet the demands when dispensing these products. PURPOSE: This review aims to map the use of 3D printing in the manufacture of orthoses and prostheses for people with physical disability at rehabilitation centers. METHODS: Publications that deal with the use of 3D printing for the manufacture of orthoses and prostheses were used, preferably studies from 2012 to 2022. RESULTS: The majority of studies, 56.25%, were quantitative and 46.25% were evaluative research. None of the studies were characterized as developed at rehabilitation centers. 75% of them had the participation of people with physical disability. The use of 3D printing was, for the most part, for the development of assistive technologies for the upper limbs at 56.25%, while 31.25% were for the lower limbs. CONCLUSION: The assistive products developed were orthoses and prostheses for the wrist, hands, fingers, upper limbs, writing devices, sockets, knees, and feet. Although there were positive results in their performance, some limitations related to strength, stiffness, and resistance were observed.

Repair of iatrogenic left pulmonary artery to left atrial appendage fistula using a covered CP stent: a case report.

We report a case of iatrogenic left pulmonary artery-left atrial appendage fistula following percutaneous transluminal angioplasty for residual pulmonary artery stenosis in an 11-year-old boy. This rare complication could have been predicted by understanding the anatomical relationship of these structures. In this study, simulation using three-dimensional printing greatly contributed to successful stent placement.

3D-printed thermally expanded monolithic foam for solid-phase extraction of multiple trace metals.

Digital light processing (DLP) 3DP, commercial acrylate-based photocurable resins, and thermally expandable microspheres-incorporated flexible photocurable resins were employed to fabricate an SPE column with a thermally expanded monolithic foam for extracting Mn, Co, Ni, Cu, Zn, Cd, and Pb ions prior to the determination using inductively coupled plasma mass spectrometry. After optimization of the thermally activated foaming, the design and fabrication of the SPE column, and the automatic analytical system, the DLP 3D-printed SPE column with the thermally expanded monolithic foam extracted the metal ions with up to 14.8-fold enhancement (relative to that without incorporating the microspheres), with absolute extraction efficiencies all higher than 95.6%, and method detection limits in the range from 0.5 to 5.2 ng L-1. We validated the reliability and applicability of this method by determination of the metal ions in several reference materials (CASS-4, SLRS-5, 1643f, and Seronorm Trace Elements Urine L-2) and spiked seawater, river water, ground water, and human urine samples. The results illustrated that to incorporate the thermally expandable microspheres into the photocurable resins with a post-printing heating treatment enabled the DLP 3D-printed thermally expanded monolithic foam to substantially improve the extraction of the metal ions, thereby extending the applicability of SPE devices fabricated by vat photopolymerization 3DP techniques.

3D-printed polycaprolactone scaffolds coated with beta tricalcium phosphate for bone regeneration.

BACKGROUND/PURPOSE: 3D-printing technology is an important tool for the bone tissue engineering (BTE). The aim of this study was to investigate the interaction of polycaprolactone (PCL) scaffolds and modified mesh PCL coated with beta TCP (PCL/ß-TCP) scaffolds with MG-63. METHODS: This study used the fused deposition modeling (FDM) technique with the 3D printing technique to fabricate the thermoplastic polymer and composite scaffolds. Scaffold structure and coating quality were observed under a scanning electron microscope (SEM). MG-63 cells were injected and attached to the mesh-manufactured PCL scaffolds. The biocompatibility of mesh structured PCL and PCL/ß-TCP scaffolds could be examined by measuring the viability of MG-63 cells of MTT assay. Bone cell differentiation was evaluated ALP activity by mineralization assay. RESULTS: The results showed that both mesh PCL scaffolds and PCL/ß-TCP scaffolds were non-toxic to the cells. The ALP activities of cells in PCL/ß-TCP scaffolds groups were significant differences and better than PCL groups in all groups at all experimental dates. The mineralization process was time-dependent, and significantly higher mineralization of osteosarcoma cells was observed on PCL/ß-TCP scaffolds at experimental dates. CONCLUSION: We concluded that both meshes structured PCL and PCL/ß-TCP scaffolds could promote the MG-63 cell growth, and PCL/ß-TCP was better than the PCL scaffolds for the outcome of MG63 cell differentiation and mineralization.

Development and Investigation of a Grasping Analysis System with Two-Axis Force Sensors at Each of the 16 Points on the Object Surface for a Hardware-Based FinRay-Type Soft Gripper.

The FinRay soft gripper achieves passive enveloping grasping through its functional flexible structure, adapting to the contact configuration of the object to be grasped. However, variations in beam position and thickness lead to different behaviors, making it important to research the relationship between structure and force. Conventional research using FEM simulations has tested various virtual FinRay models but replicating phenomena such as buckling and slipping has been challenging. While hardware-based methods that involve installing sensors on the gripper and the object to analyze their states have been attempted, no studies have focused on the tangential contact force related to slipping. Therefore, we developed a 16-way object contact force measurement device incorporating two-axis force sensors into each of the 16 segmented objects and compared the normal and tangential components of the enveloping grasping force of the FinRay soft gripper under two types of contact friction conditions. In the first experiment, the proposed device was compared with a device containing a six-axis force sensor in one segmented object, confirming that the proposed device has no issues with measurement performance. In the second experiment, comparisons of the proposed device were made under various conditions: two contact friction states, three object contact positions, and two object motion states. The results demonstrated that the proposed device could decompose and analyze the grasping force into its normal and tangential components for each segmented object. Moreover, low friction conditions result in a wide contact area with lower tangential frictional force and a uniform normal pushing force, achieving effective enveloping grasping.

Investigating the impact of post-curing cycles on surface hardness and color stability in 3D printed resin crowns.

This study evaluated the effect of different post-curing cycles on the Vickers hardness, color change, and translucency value of 3D printed methacrylic acid ester-based temporary and permanent crown resins. A total of 300 samples were printed in disk shape (ø:8 mm, thickness: 2 mm) using VarseoSmile Crown Plus (VSC) and VarseoSmile Temp (VST) materials from a 3D printer. These disks were divided into five subgroups (n = 30 each) based on flash-curing cycles (0, 750, 1500, 2250, and 3000). Surface hardness tests and color tests were conducted on both the green state and flash-cured groups. The data were analyzed using univariate analysis of variance (ANOVA). The hardness of 3D printed temporary and permanent crown resin increased with post-curing time. Compared to the post-curing cycle recommended by the manufacturer, no clinically significant color change (ΔE00 ≥ 2.25) was observed in any of the polymerized groups. It was determined that permanent crown material had a more translucent structure than temporary crown material. The interaction between material and post-curing had significant effects on surface hardness, color (ΔE00), and translucency of 3D printed methacrylic acid ester-based resins.

German Chamomile (Matricaria chamomilla L.) Flower Extract, Its Amino Acid Preparations and 3D-Printed Dosage Forms: Phytochemical, Pharmacological, Technological, and Molecular Docking Study.

German chamomile (Matricaria chamomilla L.) is an essential oil- containing medicinal plant used worldwide. The aim of this study was to gain knowledge of the phytochemical composition and the analgesic and soporific activity of Matricaria chamomilla L. (German chamomile) flower extract and its amino acid preparations, to predict the mechanisms of their effects by molecular docking and to develop aqueous printing gels and novel 3D-printed oral dosage forms for the flower extracts. In total, 22 polyphenolic compounds and 14 amino acids were identified and quantified in the M. chamomilla extracts. In vivo animal studies with rodents showed that the oral administration of such extracts revealed the potential for treating of sleep disorders and diseases accompanied by pain. Amino acids were found to potentiate these effects. Glycine enhanced the analgesic activity the most, while lysine and ß-alanine improved the soporific activity. The molecular docking analysis revealed a high probability of γ-aminobutyric acid type A (GABAA) and N-methyl-D-aspartate (NMDA) receptor antagonism and 5-lipoxygenase (LOX-5) inhibition by the extracts. A polyethylene oxide (PEO)-based gel composition with the M. chamomilla extracts was proposed for preparing a novel 3D-printed dosage form for oral administration. These 3D-printed extract preparations can be used, for example, in dietary supplement applications.

Accuracy assessment between computer-guided surgery planning and actual tooth position during tooth autotransplantation.

BACKGROUND/AIM: This study aims to evaluate the precision and efficacy of utilizing computer-aided design (CAD) in combination with three-dimensional printing technology for tooth transplantation. MATERIAL AND METHODS: This study analysed 50 transplanted teeth from 48 patients who underwent tooth transplantation surgery with the aid of CAD and positional guides. A consistent coordinate system was established using preoperative and postoperative cone-beam computed tomography images. Linear displacements and angular deviations were calculated by identifying key regions in both virtual designs and actual transplanted teeth. Additionally, an analysis was conducted to explore potential factors influencing these deviations. RESULTS: The mean cervical deviation, apical deviation, and angular deviation among the 50 transplanted teeth were 1.16 ± 0.57 mm, 1.80 ± 0.94 mm, and 6.82 ± 3.14°, respectively. Cervical deviation was significantly smaller than apical deviation. No significant difference in deviation was observed among different recipient socket locations, holding true for both single-root, and multi-root teeth. However, a significant difference was noted in apical deviation between single-root and multi-root teeth. Our analysis identified a correlation between apical deviation and root length, leading to the development of a prediction model: Apical deviation = 0.1390 × (root length) + 0.2791. CONCLUSIONS: The postoperative position of the donor teeth shows discrepancies compared to preoperative simulation when utilizing CAD and 3D printed templates during autotransplantation procedures. Continual refinement of preoperative design is a crucial endeavour.

Assessing hand grasp in patients with systemic sclerosis using the 16-grasp test: Preliminary results from a multidisciplinary study group.

BACKGROUND: Reports on hand dysfunction and rehabilitation in SSc are quite scarce in the literature and mainly focus on functional assessment tools, such as the Duruoz Hand Index and the HAMIS test for evaluating hand mobility by simulating specific grasps with nine different objects. PURPOSE OF THE STUDY: This study aimed to provide an adequate assessment methodology for hand grasp dysfunctions in patients suffering from systemic sclerosis (SSc) through the 16-grasp test. STUDY DESIGN: Case-control study. METHODS: Ninety-seven consecutive SSc patients were recruited at our Scleroderma Unit, where a 16-grasp test was performed by all patients and supervised by an experienced hand therapist. Sixteen different patterns of grasp have been divided into power grasps and precision pinch and two more modalities: static and dynamic prehension evaluation on scale from 0 to 4. We also compared previous evaluations on 19 of patients recruited. RESULTS: The majority of SSc patients (84 females and 13 males; mean age 56.0±12.0 years; mean disease duration 8.0±6.0 years) displayed grasp dysfunctions; in particular 48% and 54% reported slight difficulty in the right and left grasps respectively, 6% medium difficulty in both hands, and only 3% and 1% experienced severe difficulty respectively, while 31.5% had no issues in either hand. Our results showed that the limited cutaneous subset (lcSSc) scored a lower deficit for either grasp compared to diffuse form (dcSSc). No statistically significant differences in total grasp deficit had been noticed when comparing patients having a disease duration < 5 years or longer. In the retrospective study on 19 of these patients, 8 out of 10 lcSSc patients showed no significant changes, while in 2 out of 10, slight improvements were observed in both hands. However, in the dcSSc group, 4 out of 9 worsened bilaterally while the grasp scores for 5 of them remained unchanged. CONCLUSION: Our study reported hand involvement in both lcSSc and dcSSc forms, more significantly in dcSSc patients. This test is intended to be a more objective means of assessing grasp alterations linked to scleroderma hand deformities. Furthermore, thanks to its intuitiveness, the test may be useful for engineers designing personalized ergonomic assistive devices.

Fabrication of 3D-printed scaffolds loaded with gallium acetylacetonate for potential application in osteoclastic bone resorption.

We recently reported the potential of a new gallium compound, gallium acetylacetonate (GaAcAc) in combating osteoclastic bone resorption through inhibition of osteoclast differentiation and function. Herein, we focused on 3D-printed polylactic acid scaffolds that were loaded with GaAcAc and investigated the impact of scaffold pretreatment with polydopamine (PDA) or sodium hydroxide (NaOH). We observed a remarkable increase in scaffold hydrophilicity with PDA or NaOH pretreatment while biocompatibility and in vitro degradation were not affected. NaOH-pretreated scaffolds showed the highest amount of GaAcAc loading when compared to other scaffolds (p < 0.05). NaOH-pretreated scaffolds with GaAcAc loading showed effective reduction of osteoclast counts and size. The trend was supported by suppression of key osteoclast differentiation markers such as NFAT2, c-Fos, TRAF6, & TRAP. All GaAcAc-loaded scaffolds, regardless of surface pretreatment, were effective in inhibiting osteoclast function as evidenced by reduction in the number of resorptive pits in bovine cortical bone slices (p < 0.01). The suppression of osteoclast function according to the type of scaffold followed the ranking: GaAcAc loading without surface pretreatment > GaAcAc loading with NaOH pretreatment > GaAcAc loading with PDA pretreatment. Additional studies will be needed to fully elucidate the impact of surface pretreatment on the efficacy and safety of GaAcAc-loaded 3D-printed scaffolds.

Three-dimensional replica of the temporal bone in the teaching of human anatomy.

PURPOSE: The current study proposes the comparison of the visualization and identification of anatomical details between natural human temporal bone, its respective copy from three-dimensional printing, and the virtual model obtained from CBCT. METHODS: The sample consisted of undergraduate students in Dentistry (Group UE, n = 22), Postgraduate students in Radiology and Imaging (Group P-RI, n = 20), and Postgraduate students in Forensic Odontology (Group P-FO, n = 24). All participants attended a theoretical class on specialized anatomy of the temporal bone and subsequently performed the markings of 10 determined structures. RESULTS: The number of correct identifications was similar in natural bone and printed three-dimensional models in all groups (p > 0.05). The virtual model showed a significantly lower number of correct structures (p < 0.05) in the 3 groups. In general, there were significantly higher percentages of accurate answers among postgraduate students compared to undergraduate students. Most graduate students believed that the printed three-dimensional model could be used to teach anatomy in place of natural bone, while undergraduate students disagreed or were unsure (p < 0.05). Regarding the virtual tomographic image, in all groups, students disagreed or were not sure that its use would be beneficial in replacing natural bone. CONCLUSION: Three-dimensional and virtual models can be used as auxiliary tools in teaching anatomy, complementing practical learning with natural bones.

Micro-computed tomographic evaluation of the shaping ability of three nickel-titanium rotary systems in the middle mesial canal of mandibular first molars: an ex vivo study based on 3D printed tooth replicas.

BACKGROUND: The preparation of the middle mesial (MM) canal of mandibular molars represents a challenge because it is often curved, narrow, and close to the root concave. The purpose of this study was to evaluate the ex vivo shaping ability of 3 nickel-titanium (NiTi) rotary systems in the MM canal using 3D printed resin tooth replicas. METHODS: A permanent mandibular first molar with a MM canal was acquired from a pool of extracted teeth and reproduced by a 3D printer. The resin tooth replicas (n = 18) were equally assigned to 3 groups for the evaluation of the shaping abilities of 3 NiTi rotary systems (OneShape [OS], Twisted Files [TF], and ProTaper Gold [PTG]) according to the manufacturer's recommendations. The tooth replicas were scanned by micro-computed tomography (micro-CT) twice before and after instrumentation of the mesiobuccal (MB), mesiolingual (ML), and MM root canals. After 3D reconstruction, the canal straightening, change of root canal volume and surface area, the mesial and distal canal wall thickness and canal transportation at the levels of 1, 2, and 3 mm below furcation were assessed. One-way variance analysis and Turkey's post hoc test were used for comparisons of the means among different groups, and paired-t test was used to compare the mesial and distal sides of the mesial roots. RESULTS: As compared with OS and TF, the use of PTG in preparation of MM canals resulted in significantly more straightening of canal curvature (p < 0.05), greater post-instrumentation canal volume and surface area, and thinner mesial and distal remaining canal wall thickness at 1, 2 and 3 mm below furcation (all p < 0.05). Regarding the root canal transportation in the mesiodistal direction, there was no significant difference among the 3 instruments (all p > 0.05) after the preparation of the MB and ML canals. However, in the MM canal, more pronounced transportation was detected in the PTG group at 2 mm below furcation, and in the TF group at 3 mm below furcation as compared with the other 2 systems (both p < 0.05). CONCLUSIONS: 3D printed tooth replicas have the advantages of consistency and can be an ideal model to evaluate the shaping ability of different instruments in the MM canal. OS and TF files performed similarly and both are appropriate for shaping the MM canal, while PTG may cause excessive and uneven resin removal, especially near the furcation, and may lead to root fragility and procedural errors.

Effect of immersion in disinfectants on the color stability of denture base resins and artificial teeth obtained by 3D printing.

PURPOSE: To evaluate the effect of immersion in disinfecting solutions on the color stability of denture base resins and artificial teeth obtained by 3D printing. MATERIALS AND METHODS: Forty discs (15 × 3 mm) were obtained for each group: Lucitone 550 and Cosmos Denture 3D (denture base resins), Duralay and Cosmos TEMP 3D (artificial teeth resins). The discs were immersed in disinfectant solutions: Corega Tabs, 2% chlorhexidine digluconate, 0.25% sodium hypochlorite, and distilled water. Color measurements were obtained with a spectrophotometer before immersion in disinfectants and after the simulated periods of 6 and 12 months. Data (ΔE00 ) were submitted to mixed three-way ANOVA and Bonferroni post-test. RESULTS: For denture base resins, Cosmos Denture 3D showed greater color change regardless of the solution and immersion time. The immersion time of 6 months influenced the color change of the denture base resins regardless of the disinfectant solution. For the artificial teeth resins, the immersion time of 12 months showed a significant color change when compared to 6 months. Cosmos TEMP 3D showed greater color change for all solutions, except for 0.25% sodium hypochlorite. Duralay resin showed greater color change in 2% chlorhexidine, regardless of immersion time. CONCLUSIONS: For denture base resins, the immersion time significantly changed the color regardless of the solution. For artificial teeth resins, Cosmos TEMP 3D showed greater color changes in all solutions when compared to Duralay, except for 0.25% sodium hypochlorite. Chlorhexidine digluconate significantly changed the color of Duralay.

Effect of different storage conditions on dimensional accuracy of 3D-printed dental models.

PURPOSE: The objective was to determine the accuracy of 3D-printed dental models subjected to different storage conditions using six different material and printer combinations. MATERIALS AND METHODS: Three completely dentate models were designed using dental CAD software (3Shape Dental System). A horseshoe-shaped solid base with a posterior horizontal bar was used. The models were printed in a horizontal direction against the building platform without support. The models were printed using six printers with the corresponding recommended resin material: Carbon M2 (DPR10), HeyGears A2D4K (Model HP UV2.0), Stratasys J5 (MED610), Stratasys Origin One (DM200), Envision One (E-Model LightDLP), and Asiga Pro4K (VeriModel) with a standard layer thickness of 50 µm. All printed models underwent scanning using a laboratory scanner (Sirona inEOS X5) after printing. Subsequently, the models were randomly assigned into three groups of storage conditions, LT: cold environment (4 ± 1°C), HT: hot and dry environment (50 ± 2°C), and RT: room temperature (25 ± 2°C) serving as the control. Each group was kept under the designated condition and was scanned at 1, 2, 3, 4, and 8 weeks. The total number of models (N) was 72, with 6 printers producing 12 models per printer for 3 storage conditions, resulting in 4 models for each storage condition and each printer. The generated STL files were imported into a 3D inspection software for comparison with the original STL files. In-tolerance percentage, the deviation RMS, trueness, and precision were obtained and analyzed with least square mean linear regression using JMP Pro 15 to identify the significant effects (α = 0.05). RESULTS: The in-tolerance percentage as-printed was significantly different among different printers. Significant dimension deviations were observed after the first week of storage at HT and with subsequent weeks of storage. RT and LT did not show significant dimensional changes. Models printed with Carbon M2 showed the highest in-tolerance percentages compared to the other printers. CONCLUSIONS: The model deviations were affected by storage conditions and the printer used, with high-temperature storage showed least stability compared to low and room temperatures. No significant difference was observed between low and room temperature storage conditions. The Carbon M2 printer showed the highest accuracy among all printers tested. The region had a significant effect on the deviation measured, with the abutment body showing the least deviation. Among the 3D printers evaluated, A2D4K by HeyGears and Carbon M2 printers demonstrated the highest accuracy in terms of both precision and trueness.

Three-dimensional printed models can reduce costs and surgical time for complex proximal humeral fractures: preoperative planning, patient satisfaction, and improved resident skills.

BACKGROUND: Proximal humeral fractures (PHFs) are still controversial with regards to treatment and are difficult to classify. The study's objective is to show that preoperative planning performed while handling a three-dimensional (3D) printed anatomical model of the fracture can ensure a better understanding of trauma for both surgeons and patients. MATERIALS AND METHODS: Twenty patients (group A, cases) with complex PHF were evaluated preoperatively by reproducing life-size, full-touch 3D anatomical models. Intraoperative blood loss, radiographic controls, duration of surgery, and clinical outcomes of patients in group A were compared with 20 patients (group B, controls) who underwent standard preoperative evaluation. Additionally, senior surgeons and residents, as well as group A patients, answered a questionnaire to evaluate innovative preoperative planning and patient compliance. Cost analysis was evaluated. RESULTS: Intraoperative radiography controls and length of operation were significantly shorter in group A. There were no differences in clinical outcomes or blood loss. Patients claim a better understanding of the trauma suffered and the proposed treatment. Surgeons assert that the planning of the definitive operation with 3D models has had a good impact. The development of this tool has been well received by the residents. The surgery was reduced in length by 15%, resulting in savings of about EUR 400 for each intervention. CONCLUSIONS: Fewer intraoperative radiography checks, shorter surgeries, and better patient compliance reduce radiation exposure for patients and healthcare staff, enhance surgical outcomes while reducing expenses, and lower the risk of medicolegal claims. LEVEL OF EVIDENCE: Level I, prospective randomized case-control study.