Forces required to dynamize sliding screws in gamma nail and selfdynamizable internal fixator.

BACKGROUND: Single limb support phase of the gait-cycle in patients who are treated for a pertrochanteric fracture is characterized by transversal loads acting on the lag screw, tending to block its dynamization. If the simultaneous axial force overcomes transversal loads of the sliding screw, the dynamization can still occur. METHODS: Biomechanical investigation was performed for three types of dynamic implants: Gamma Nail, and two types of Selfdynamizable Internal Fixators (SIF) - SIF-7 (containing two 7 mm non-cannulated sliding screws), and SIF-10 (containing one 10 mm cannulated sliding screw). Contact surface between the stem and the sliding screws is larger in SIF implants than in Gamma Nail, as the stem of Gamma Nail is hollow. A special testing device was designed for this study to provide simultaneous application of a controlled sliding screws bending moment and a controlled transversal load on sliding screws (Qt) without using of weights. Using each of the implants, axial forces required to initiate sliding screws dynamization (Qa) were applied and measured using a tensile testing machine, for several values of sliding screws bending moment. Standard least-squares method was used to present the results through the linear regression model. RESULTS: Positive correlation between Qt and Qa was confirmed (p < 0.05). While performing higher bending moments in all the tested implants, Qa was higher than it could be provided by the body weight. It was the highest in Gamma Nail, and the lowest in SIF-10. CONCLUSIONS: A larger contact surface between a sliding screw and stem results in lower forces required to initiate dynamization of a sliding screw. Patients treated for a pertrochanteric fracture by a sliding screw internal fixation who have longer femoral neck or higher body weight could have different programme of early postoperative rehabilitation than lighter patients or patients with shorter femoral neck.

The small screw-apex distance is potentially associated with femoral head osteonecrosis in adults with femoral neck fractures treated by closed reduction and percutaneous 3 parallel cannulated screws.

OBJECTIVE: Femoral neck fractures (FNFs) are among the most common fractures in elderly individuals. Surgery is the main treatment for FNFs, and osteonecrosis of the femoral head (ONFH) is one of the unacceptable complications. This study aimed to assess both the clinical and radiological outcomes in patients with FNFs treated with three parallel cannulated screws and to identify relationship between screws position and ONFH. PATIENTS AND METHODS: A total of 100 patients who were treated with closed reduction and fixed with 3 parallel cannulated screws met the inclusion criteria between January 2014 and December 2020 at authors' institution. The follow-up duration, age, sex, affected side, and injury-to-surgery interval were collected; the neck-shaft angle of both hips, screw-apex distance (SAD) and the tip-apex distance (TAD)were measured; and the Garden classification, quality of reduction and presence of ONFH were evaluated. RESULTS: The sample consisted of 37 males and 63 females, with 60 left and 40 right hips affected. The mean age of patients was 54.93 ± 12.24 years, and the mean follow-up was 56.3 ± 13.38 months. The overall incidence of ONFH was 13%. No significant difference was observed in the incidence of ONFH by affected side, age, fracture displacement, injury-to-surgery interval, neck-shaft angle deviation, or reduction quality. The SAD was significantly shorter in ONFH patients than in normal patients for all three screws (p = 0.02, 0.02, and 0.01, respectively). CONCLUSIONS: The short SAD of all screws is associated with femoral head necrosis of FNFs treated with 3 cannulated screws. The short SAD indicated that screws malpositioning in the weight-bearing area of the femoral head, potentially harming the blood supply and compromising the anchorage of the primary compressive trabeculae in this region.

Robot-assisted Temporary Hemiepiphysiodesis With Eight-plates for Lower Extremity Deformities in Children.

PURPOSE: This study was performed to compare the radiographic results of robot-assisted and traditional methods of treating lower extremity deformities (LEDs). METHODS: From January 2019 to February 2022, 55 patients with LEDs were treated by temporary hemiepiphysiodesis with eight-plates. They were divided into a robot group and a freehand group. The fluoroscopy time and operation time were recorded. The accuracy of screw placement was measured after the operation using the following parameters: coronal entering point (CEP), sagittal entering point (SEP), and angle between the screw and epiphyseal plate (ASEP). The limb length discrepancy (LLD) and femorotibial angle (FTA) were measured before the operation, after the operation, and at the last follow-up. Patients were followed up for 12 to 24 months, and the radiographic results of the 2 groups were compared. RESULTS: Among the 55 patients with LEDs, 36 had LLD and 19 had angular deformities. Seventy-six screws were placed in the robot group and 85 in the freehand group. There was no difference in the CEP between the 2 groups ( P >0.05). The robot group had a better SEP (2.96±1.60 vs. 6.47±2.80 mm) and ASEP (3.46°±1.58° vs. 6.92°±3.92°) than the freehand group ( P <0.001). At the last follow-up, there was no difference in the LLD or FTA improvement between the two groups ( P >0.05). The incidence of complications was significantly lower in the robot group than in the freehand group (0/27 vs. 5/28, P <0.05). CONCLUSION: Robot-assisted temporary hemiepiphysiodesis with eight-plates is a safe and effective method for treating LEDs in children. Robotic placement of screws is superior to freehand placement with respect to the entering position and direction. Although the correction effect for LLD and angular deformity is similar, screw dislocation is less common when using robot assistance. LEVELS OF EVIDENCE: Level-III. Retrospective comparative study.

Tibial fracture associated with use of Arthrex self-tapping screws during tibial plateau leveling osteotomy in dogs and development of transcortical tibial fracture.

OBJECTIVE: Medical records for dogs treated with tibial plateau leveling osteotomy (TPLO) using Arthrex 3.5 mm self-tapping screws (STS) were evaluated to determine the incidence rate of transcortical tibial fractures (TCTF) and development of complications. STUDY DESIGN: Retrospective case report. STUDY POPULATION: A total of 78 dogs. METHODS: Dogs that underwent a TPLO performed from March 2022 to August 2023 were reviewed. Postoperative TPLO radiographs were examined for evidence of a TCTF with Arthrex 3.5 mm STS. Records were reviewed for complications up to 14 weeks after surgery. RESULTS: Evidence of a TCTF was found in 42% of cases (33 of 78) and 14% (36 of 250) of STS screws distal to the osteotomy. TCTFs were only identified distal to the osteotomy. Three dogs had radiographic evidence of more than one TCTF. Of the dogs with radiographic TCTF, 6% of patients (2 of 33) developed a major complication that required surgical stabilization of a tibial fracture associated with screw angulation relative to the plate. CONCLUSION: Use of Arthrex 3.5 mm STS for TPLO is associated with risk of TCTF. TCTF can compromise the structural properties of the tibia and cause complete tibial fracture requiring major revision surgery. CLINICAL SIGNIFICANCE: Development of TCTF after use of STS for TPLO has been recognized, in contrast to use of non-self-tapping screws, and was considered a benign complication. Our findings suggest TCTF associated with Arthrex 3.5 mm STS use in TPLO can contribute to major complications after surgery, including complete tibial fracture, particularly if screws are not placed perpendicular to the plate.

Peroneal artery injury potential due to different syndesmosis screw placement options: a simulation study with lower extremity computed tomography angiography.

INTRODUCTION: The aim of this study is to assess the risk of peroneal artery injury of hardware placement at the fixation of syndesmotic injuries. MATERIALS AND METHODS: The lower extremity computed tomography angiography was used to design the study. The syndesmosis screw placement range was simulated every 0.5 cm, from 0.5 to 5 cm proximal to the ankle joint. The screw axes were drawn as 20°, 30° or individual angle according to the femoral epicondylar axis. The proximity between the screw axis and the peroneal artery was measured in millimeters. Potential peroneal artery injury was noted if the distance between the peroneal artery to the axis of the simulated screw was within the outer shaft radius of the simulated screw. The Pearson chi-square test was used and a p-value < 0.05 was considered significant. RESULTS: The potential for injury to the peroneal artery increased as the syndesmosis screw level rose proximally from the ankle joint level or as the diameter of the syndesmosis screw increasds. In terms of syndesmosis screw trajection, the lowest risk of injury was observed with the syndesmosis screw angle of 20°. Simulations with a screw diameter of 3.5 mm exhibited the least potential for peroneal artery injury. CONCLUSION: Thanks to this radiological anatomy simulation study, we believe that we have increased the awareness of the peroneal artery potential in syndesmosis screw application. Each syndesmosis screw placement option may have different potential for injury to the peroneal artery. To decrease the peroneal artery injury potential, we recommend the followings. If individual syndesmosis screw angle trajection can be measured, place the screw 1.5 cm proximal to the ankle joint using a 3.5 mm screw shaft. If not, fix it with 30° trajection regardless of the screw diameter at the same level. If the most important issue is the peroneal artery circulation, use the screw level up to 1 cm proximal to the ankle joint regardless of the screw angle trajection and screw diameter.

Low avascular necrosis rates in femoral neck fractures: efficacy of cannulated screw fixation.

PURPOSE: Cannulated screw fixation for femoral neck fractures is often limited by concerns of avascular necrosis (AVN) occurring, historically seen in 5-40% of fixed intracapsular fractures. This study aims to assess the outcomes, particularly the AVN rate, associated with current surgical techniques within our unit. METHODS: We conducted a single-center cross-sectional study, manually searching operative records between July 14, 2014, and December 1, 2018, identifying patients with intracapsular fractured neck of femur fixed with cannulated screws, with a minimum of two years follow-up. Patient records and radiographs were reviewed for clinical and radiographic diagnoses of AVN, non-union, post-operative metalwork infection, and screw penetration of the head. Additionally, fracture pattern and displacement, screw configuration, reduction techniques, and adequacy of reduction were recorded, with radiographs independently analyzed by four orthopedic surgeons. RESULTS: Fifty-six patients were included; average age of 67 years (range 30-100). Forty-two patients (75%) sustained displaced fractures and 14 patients (25%) had undisplaced fractures. Two (4%) patients developed AVN, with no cases of non-union, post-operative metalwork infection or screw penetration of the head. Eight patients (14%) sustained a high-energy injury, though none of these patients developed AVN. All fractures required closed reduction; no open reductions performed. Twenty-seven (64%) of reductions were adequate. CONCLUSION: Our observed AVN rate is notably lower than the widely reported figures, even among a significant proportion of displaced fractures that were fixed. This study underscores that with adequate fixation, cannulated screws represent an excellent option for treating intracapsular neck of femur fractures, even in cases of displaced fracture patterns with imperfect reduction.

Finite element study on post-screw removal stress in toy poodle radius with different plate designs and screw arrangements.

Background: The study employs finite element analysis to investigate stress distribution in the radius of toy poodles after screw removal. The examination focuses on the biomechanical implications of varied screw hole configurations using 1.5 and 2.0-mm locking compression plates (LCPs) with notched head T-Plates. Aim: To provide a noninvasive approach to analyzing the immediate consequences of screw removal from the radius bone in toy poodles. Specifically, it explores the impact of varied plate designs and screw arrangements on stress distribution within the forelimb bones. Methods: The study constructs a three-dimensional bone model of the toy poodle's forelimb based on computed tomography (CT) images. Simulations were designed to replicate jumping and landing from a 40 cm height, comparing stress distribution in the radius post-screw removal. Results: The analysis reveals significant variations in stress distribution patterns between the two LCPs. The radius implanted with the 2.0-mm LCP displays a uniform stress distribution, contrasting with the 1.5-mm plates. Localized stress concentration is observed around the screw holes, while trabecular bone regions near the screw holes exhibit lower stress levels. Conclusion: The study highlights the plate designs and screw configurations that affect bone stress in toy poodle forelimbs post-screw removal. The findings provide valuable insights for veterinarians, aiding informed decisions in veterinary orthopedic practices.

Interfaces between Cranial Bone and AISI 304 Steel after Long-Term Implantation: A Case Study of Cranial Screws.

Interfaces between AISI 304 stainless steel screws and cranial bone were investigated after long-term implantation lasting for 42 years. Samples containing the interface regions were analyzed using state-of-the-art analytical techniques including secondary ion mass, Fourier-transform infrared, Raman, and X-ray photoelectron spectroscopies. Local samples for scanning transmission electron microscopy were cut from the interface regions using the focused ion beam technique. A chemical composition across the interface was recorded in length scales covering micrometric and nanometric resolutions and relevant differences were found between peri-implant and the distant cranial bone, indicating generally younger bone tissue in the peri-implant area. Furthermore, the energy dispersive spectroscopy revealed an 80 nm thick steel surface layer enriched by oxygen suggesting that the AISI 304 material undergoes a corrosion attack. The attack is associated with transport of metallic ions, namely, ferrous and ferric iron, into the bone layer adjacent to the implant. The results comply with an anticipated interplay between released iron ions and osteoclast proliferation. The interplay gives rise to an autocatalytic process in which the iron ions stimulate the osteoclast activity while a formation of fresh bone resorption sites boosts the corrosion process through interactions between acidic osteoclast extracellular compartments and the implant surface. The autocatalytic process thus may account for an accelerated turnover of the peri-implant bone.

The effect of different implant-abutment types and heights on screw loosening in cases with increased crown height space.

OBJECTIVES: The stability of the abutment screw is pivotal for successful implant-supported restorations, yet screw loosening remains a common complication, leading to compromised function and potential implant failure. This study aims to evaluate the effect of different implant-abutment types and heights on screw loosening in cases with increased crown height space (CHS). MATERIALS AND METHODS: In this in vitro study, a total of 64 abutments in eight distinct groups based on their type and height were evaluated. These groups included stock, cast, and milled abutments with heights of 4 mm (groups S4, C4, and M4), 7 mm (groups S7, C7, and M7), and 10 mm (groups C10 and M10). Removal torque loss (RTL) was assessed both before and after subjecting the abutments to dynamic cyclic loading. Additionally, the differences between initial RTL and RTL following cyclic loading were analyzed for each group (p < .05). RESULTS: The C10 group demonstrated the highest RTL, whereas the S4 group exhibited the lowest initial RTL percentage (p < .05). Furthermore, the study established significant variations in RTL percentages and the discrepancies between initial and postcyclic loading RTL across different abutment groups (p < .05). Additionally, both abutment types and heights were found to significantly influence the RTL percentage (p < .05). CONCLUSION: The type and height of the implant abutment affected screw loosening, and in an increased CHS of 12 mm, using a stock abutment with a postheight of 4 mm can be effective in minimizing screw loosening.

Treatment of non-displaced intracapsular femoral neck fractures with dynamic hip and cannulated screws resulting in avascular necrosis: A comparative study of complications.

OBJECTIVES: To compare the complications associated with cannulated hip screws (CHS) and dynamic hip screws (DHS) techniques. METHODS: In this multicenter retrospective chart study, we reviewed the records and data of all patients operated upon by DHS or CHS for treatment of Garden type I and type II intracapsular non-displaced femoral neck fracture from January 2017 to December 2022. Patients with incomplete files or follow-ups of less than one year were excluded from the study. RESULTS: The study enrolled 85 patients, 35 males, and 50 females, with a mean age of 72±5.4 for males and 70.6±7.6 for females. A total of 44 patients were operated upon with DHS, and 41 patients with CHS. The mortality rate of DHS was 15.9% and was 17.1% in the CHS group (p>0.05). Non-union was recorded in 4.5% of the DHS group and 4.9% of CHS patients (p>0.05). Avascular necrosis (AVN) was significantly higher in DHS (9.1%) than in CHS (4.9%, p<0.05). A revision was required in 15.9% of DHS patients and 14.6% of CHS patients (p>0.05). CONCLUSION: This study found that DHS was superior to CHS in AVN rate. However, there was no significant difference between both methods regarding mortality, revision, and non-union.

Wear and corrosion of titanium alloy spinal implants in vivo.

To investigate the wear and corrosion of titanium alloy spinal implants in vivo, we evaluated removed implants and their surrounding scar tissues from 27 patients between May 2019 and April 2021. We performed scanning electron microscopy, energy-dispersive X-ray spectroscopy, and histological analysis. The results revealed metal-like particles in the soft tissues of seven patients, without any considerable increase in inflammatory cell infiltration. Patients with fractures showed lower percentages of wear and corrosion compared with other patients (42% and 17% vs. 59% and 26%). Polyaxial screws exhibited higher wear and corrosion percentages (53% and 23%) compared with uniaxial screws (39% and 3%), although in patients with fracture, the reverse was observed (20% and 0% vs. 39% and 3%). We found that titanium alloy spinal implants experience some degree of wear and corrosion in vivo. The titanium alloy particles formed by wear exhibited good histocompatibility, not causing inflammation, foreign body reactions, or osteolysis. Therefore, spinal implants should be removed cautiously when treating titanium alloy spinal metallosis. The wear and corrosion of the implants increase with the increase in implantation time, although the screw structure does not significantly affect these changes.

Talar and fibular histiocytic-driven massive expansile osteolysis following polyetheretherketone interference screw implantation: a case report.

Numerous interference screws of different compositions exist including titanium screws, bioabsorbable screws, and polyetheretherketone (PEEK) screws. PEEK-based implants are frequently used in orthopaedic surgery due to their biocompatibility, similar elastic modulus to cortical bone, and purported negligible risk of osteolysis compared with bioabsorbable screws. In this case report, we present the case of a 48-year-old healthy female who experienced a massive osteolytic reaction in the talus and fibula after 11 weeks following implantation of PEEK-based interference screws during lateral ankle ligament reconstruction. The patient subsequently underwent removal of the PEEK screws and specimens were sent for microbiological and histopathological analysis. The specimens report demonstrated fibrotic tenosynovial soft tissue with patchy chronic inflammation, oedematous reactive changes, and histiocytic reaction, with no evidence of any significant acute inflammation. The patient recovered well and was asymptomatic at 6 months postoperatively. To our knowledge, this is the first case report of a massive osteolytic reaction to PEEK-based interference screws.

Complications Following Short Femoral Nail Fixation for Intertrochanteric Hip Fractures: A Retrospective Study.

The incidence of proximal femur fractures is increasing due to aging of the population. Intramedullary nails are the mainstay of treatment for intertrochanteric hip fractures mainly due to their better biomechanical properties compared to dynamic hip screw devices, shorter operative time, and less blood loss during surgery. However intramedullary nail fixation is not devoid of complications. The purpose of this study is to look at complications related to intramedullary nailing for intertrochanteric hip fractures in a major trauma center. A retrospective study was conducted including all patients having suffered an intertrochanteric femur fracture and treated with intramedullary nails from October 1, 2020, to October 1, 2022, in the Orthopaedic Surgery Clinic. The intramedullary hip systems used were the Stryker Gamma3 Nail and the VITUS PF Nail. All complications following the postoperative period were recorded in detail. Overall, 240 patients with a mean age of 82.3 years treated with hip intramedullary devices were identified. Superior cutout of the lag screw in two patients (females 90 and 87 years old) was identified 8 and 10 weeks following initial surgery. Avascular necrosis (AVN) of the femoral head was identified in one patient (male 81 years old) which occurred 12 weeks postoperatively. All three cases were revised by replacing the nail with cemented hemiarthroplasty. Periprosthetic fractures occurred in an 88-year-old male and a 73-year-old female following an injury distal to the stem and were managed by replacing the nail with a long stem device (Long Gamma3). One case of metalwork fracture was also recorded. There are many advantages in managing intertrochanteric hip fractures with intramedullary hip devices such as shorter theater time, less blood loss, and improved biomechanical properties. However, complications such as cutout of the lag screw, AVN, and periprosthetic fracture are serious and require complex revision surgery.

The Safety of Volar to Dorsal Percutaneous Screw Fixation of Bennett Fracture-Dislocation - A Cadaveric Study.

Background: Bennett fractures are traditionally fixed with percutaneous K-wires from dorsal to volar, or with a volar to dorsal screw via a volar open approach. While volar to dorsal screw fixation is biomechanically advantageous, an open approach requires extensive soft tissue dissection, thus increasing morbidity. This study aims to investigate the practicality and safety of Bennett fracture fixation using a percutaneous, volar to dorsal screw, particularly with regard to the median nerve and its motor branch during wire and screw insertion. Methods: Fifteen fresh frozen forearm and hand specimens were obtained from the University of Auckland human cadaver laboratory. A guidewire is placed under image intensifier from volar to dorsal with the thumb held in traction, abduction and pronation. The wire is passed through the skin volarly under image intensifier, then the median nerve is dissected from the carpal tunnel and the motor branch of the median nerve (MBMN) is dissected from its origin to where it supplies the thenar musculature. The distance between the K-wire to the MBMN is measured. Results: In 14 of 15 specimens, the wire was superficial and radial to the carpal tunnel. The mean distance to the origin of the MBMN is 6.2 mm (95% CI 4.1-8.3) with the closest specimen 1 mm away. The mean closest distance the wire gets to any part of the MBMN is 3.7 mm (95% CI 1.6-5.8); in two specimens, the wire was through the MBMN. Conclusions: Wire placement, although done under image intensifier, is subject to significant variation in exiting location. While research has shown the thenar portal in arthroscopic thumb surgery is safe, our guidewire needs to exit further ulnar to capture the Bennett fracture fragment, placing the MBMN at risk. This cadaveric study has demonstrated the proposed technique is unsafe for use.

A 56-Year-Old Woman Presenting 19 Years After Pubic Bone Fracture with a Surgical Screw Foreign Body in the Bladder.

BACKGROUND Non-calculus foreign bodies in the bladder are rare and are usually introduced via the urethra. Reports of the migration of metallic foreign bodies from previous surgery are uncommon and mainly associated with surgical screws used for the internal fixation of pubic bone fracture and total hip replacement. This report is of a 56-year-old woman presenting with a surgical screw foreign body in the bladder 19 years after open surgical reduction and internal plate and screw fixation of traumatic fracture of the pubic bone. CASE REPORT A 56-year-old woman visited a urologist because of gross hematuria. She mentioned a mild pelvic pain and multiple lower urinary tract infections over the past 2 years, with no other symptoms. From the previous history, she had undergone an open reduction and internal fixation of the pelvic ring, with surgical plates and screws following pubic bone's fracture, due to an accident 19 years earlier. Cystoscopy identified the presence of a screw head protruding into the bladder wall. The screw was extracted via open surgery, and the patient was discharged 2 days later. CONCLUSIONS While intravesical foreign bodies are rarely seen in Emergency Departments, clinicians should maintain a level of suspicion in certain cases. The purpose of this case report is to present the unlikely and delayed complication of internal pubic bone fixation resulting in the migration of a fixation screw to the bladder. It also highlights the importance of imaging in diagnosis and localization of the foreign body in the bladder.

Treatment of intertrochanteric fractures using cephalomedullary nail: One or two cephalic screws?

OBJECTIVES: To determine the incidence of cut-out, cut-in, cut-through, Z-effect, and reverse Z-effect in two cephalomedullary nail (CMN) systems: one with single cephalic screw fixation and the other with dual-screw fixation using a lag screw and an anti-rotation screw. METHODS: A retrospective study from a cohort of patients was conducted between January 2017 and August 2019 in patients with intertrochanteric fractures treated with osteosynthesis using CMN. RESULTS: One hundred ninety-six patients with intertrochanteric fractures who met the inclusion criteria were recruited. The median age was 81 years [interquartile range (IQR) 12]. Seventy-six percent had fractures classified as Orthopaedic Trauma Association/Arbeitsgemeinschaft für Osteosynthesefragen (OTA/AO) 31A2. Twenty-one mechanical complications occurred, 8.7% (17) was cut-out with a single cephalic screw CMN and 2% (4) was Z-effect with a dual-screw CMN non-integrated. The median tip-apex distance (TAD) was 19.4 mm (IQR 10.8) in patients who experienced cut-out and 19 mm (IQR 10) in those who experienced Z-effect. The median time to cut-out occurrence was 39,5 days (IQR 47,5), while the median time to Z-effect was 90 days (IQR 86). CONCLUSIONS: The incidence of osteosynthesis failure using CMN is more frequent in patients treated with a single cephalic screw CMN. LEVEL OF EVIDENCE: Therapeutic, Level III.

Utilization Trends, Patient-Demographics, and Comparison of Medical Complications of Sliding Hip Screw or Intramedullary Nail for Intertrochanteric Fractures: A Nationwide Analysis from 2005 to 2014 of the Medicare Population.

Background: Studies demonstrate an increase incidence of intertrochanteric fractures within the United States. Matched studies evaluating intertrochanteric fractures managed with either sliding hip screw (SHS) or intramedullary nail (IMN) within the Medicare population are limited. The purpose of this study was to investigate: 1) annual utilization trends; 2) patient demographics; and 3) complications including mortality. Methods: A retrospective query using a nationwide database was performed. Patients undergoing SHS or IMN for intertrochanteric fractures were identified. The query yielded a total of 37,929 patients utilizing SHS (n = 11,665) or IMN (n = 26,264). Patients were matched 1:1 based on comorbidities. Primary outcomes included: utilization trends, patient demographics, 90-day complications, and 90-day readmission rates. Linear regression analyses were used to compare utilization trends. Pearson's c2 analyses were used to compare patient-demographics, medical complications, and 90-day readmission rates. A p-value less than 0.05 was considered statistically significant. Results: Linear regression analysis demonstrated a statistically significant decrease in utilization of SHS for IT fractures (p<0.0001); whereas utilization for IMN stayed consistent (p=0.36). IMN had significantly higher prevalence of comorbidities compared to SHS, notably, hyperlipidemia (70.6 vs. 62.6%; p<0.0001). Based on 1:1 match, IMN patients had significantly higher rates of 90-day medical complications, such as respiratory failure (11.0 vs. 8.1%; p<0.0001) and VTE (4.2 vs. 3.2%; p<0.001; however, there was not a statistical difference in postoperative infection (1.4 vs. 1.5%, p=0.06). There was no statistical difference in 90-day mortality between IMN and SHS cohorts (0.19 vs .13%, p = 0.249). Conclusion: This analysis demonstrates a difference in utilization of SHS and IMN for patients with IT fractures. Patients with IMN had significantly higher prevalence of comorbid conditions and incidence of 90-day postoperative complications compared to SHS patients. The study can be utilized by orthopaedic surgeons to potentially anticipate healthcare utilization depending on implant selection. Level of Evidence: III.

Detección de tornillos prominentes en la articulación radiocarpiana mediante la proyección tangencial del escafoides dorsal / Detection of protruding screws in the radiocarpal joint using the "scaphoid skyline view"

INTRODUCCIÓN: Una de las complicaciones de la osteosíntesis retrógrada del escafoides es la protrusión del tornillo en la articulación radiocarpiana, dada la limitada visualización intraoperatoria del polo proximal del escafoides con las proyecciones tradicionales. OBJETIVO: Evaluar la capacidad de una nueva proyección radiológica, la proyección "tangencial del escafoides dorsal", o TED, para identificar tornillos prominentes radiocarpianos durante la osteosíntesis retrógrada del escafoides con tornillos canulados. MATERIALES Y MÉTODOS: Estudio cadavérico en muñecas frescas congeladas. Se introdujo en el escafoides un tornillo canulado con técnica retrógrada estándar. La proyección TED fue evaluada en 5 muñecas, con angulaciones del antebrazo de 15°, 30° y 45° para definir la mejor visualización del polo proximal del escafoides y del tornillo. Se comparó la capacidad para identificar la prominencia del tornillo en el polo proximal de la proyección TED de 30° con 5 proyecciones tradicionales de escafoides en 9 muñecas. El tornillo se posicionó a nivel de la superficie del escafoides, y luego se avanzó a intervalos de 0,5 mm bajo visualización directa por artrotomía dorsal. Tras cada intervalo, se repitieron todas las proyecciones para determinar su capacidad de detectar tornillos prominentes en el escafoides. RESULTADOS: La mejor visualización del polo proximal del escafoides se logró con la proyección TED de 30°. Al comparar la proyección TED de 30° y las tradicionales, con la TED se logró identificar tornillos prominentes a 0,8 mm promedio, seguida por la proyección posteroanterior con cubitalización y extensión a 1.3 mm (p » 0.014), con una alta precisión y correlación interobservador de estas proyecciones. CONCLUSIÓN: La proyección TED demostró ser la más sensible para detectar tornillos prominentes en la articulación radiocarpiana. Su uso rutinario podría evitar complicaciones durante la osteosíntesis.

INTRODUCTION: One of the complications of the retrograde percutaneous scaphoid fixation is the protrusion of the screw in the radiocarpal joint due to the limited intraoperative visualization of the proximal pole of the scaphoid with the traditional radiographic views. OBJETIVE: To evaluate the sensitivity of a novel radiographic view (the skyline scaphoid view, SSV) to detect screws protruding in the radiocarpal joint during the retrograde fixation of the scaphoid. MATERIALS AND METHODS: We studied nine cadaverous fresh frozen wrists. A retrograde cannulated screw was inserted in the scaphoid. To validate the SSV, 5 wrists were studied, comparing 3 forearm angulations (15°, 30° and 45°) to get the best visualization of the proximal pole and screw. We compared the ability to identify the protrusion of the screw in the proximal pole of the 30° SSV with that of 5 standard scaphoid radiographic views in 9 wrists. The screw was positioned at the level of the surface of the scaphoid, and was sequentially protruded in 0.5 mm increments, with direct visualization of its tip through a dorsal capsulotomy. After each increment, all views were repeated to determine if they were able to detect screws projecting from the scaphoid. RESULTS: The best visualization of the proximal pole of the scaphoid was found with the 30° SSV. In the comparison of the 30° SSV and the standard views, with the SSV we were able to identify the protrusion of the screws at an average of 0.8 mm, followed by the posterior-anterior view with ulnar deviation and extension at 1.3 mm (p » 0.014), with high precision and interobserver agreement regarding these views. CONCLUSION: The SSV was the most sensitive view to detect protruding screws in the proximal pole of the scaphoid. Its routine use could avoid complications during osteosynthesis.

Fracturas ipsilaterales proximales y diafisarias de fémur: ¿existe una mejor opción terapéutica?: revisión bibliográfica / Ipsilateral proximal and shaft femoral fractures: is there a better therapeutic option?: review / Fracturas ipsilaterais proximais e diafisárias do fémur: existe uma melhor opção terapêutica?: revisão bibliográfica

Introducción: Las fracturas ipsilaterales proximales de fémur ocurren en el 1 al 9% de las fracturas diafisarias. Existen múltiples tratamientos propuestos para dicha asociación lesional. El objetivo de este trabajo es revisar los diferentes métodos de tratamiento propuestos, y comparar sus resultados funcionales y principales complicaciones. Materiales y Métodos: Se utilizaron los buscadores electrónicos: PubMed, Lilacs, Cochrane y Ovid SP. La búsqueda llegó a un total de 1829 trabajos, de los cuales se seleccionaron 21 según criterios de inclusión y exclusión. Discusión: No existe un consenso acerca de cuál es el mejor método de fijación para esta asociación lesional. Esta ocurre en pacientes jóvenes por un mecanismo axial de alta energía cinética y la opción elegida debe buscar la reducción anatómica de la fracturas proximales de fémur. Las complicaciones como la pseudoartrosis de cuello femoral y la necrosis avascular son de difícil manejo en este grupo etario. Conclusión: Las fracturas ipsilaterales proximales y diafisarias de fémur son lesiones que presentan un problema diagnóstico y terapéutico. Hay un subdiagnóstico de las mismas y no existe un implante ideal, ni un consenso de cual es el mejor método de fijación.

Introduction: Ipsilateral proximal femoral fractures ocurred in 1 to 9% of femoral shaft fractures. There are multiple treatments proposed for these injuries. The objetive of the present work is revise the different treatment options and compare their functional results and main complications Materials and methods: A comprehensive literature search was carried out using: Pubmed, Lilacs, Cochrane and OVID SP. Initially there were identified a total of 1829 studies. Only 21 studies remained after inclusion and exclusion were applied. Discussion: There is no consensus about which is the best fixation option for these injuries. These occurred in young patients as a result of a high energy axial trauma, and the selected treatment must achieve anatomic reduction of the proximal femoral fracture. Complications such as femoral neck no-union and avascular necrosis are difficult to manage at this age. Conclusion: Ipsilateral proximal and shaft femoral fractures present diagnostic and therapeutic problems. There is an underdiagnosis of these injuries, and there is no ideal implant or consensus on which is the best fixation method.

Introdução: As fraturas proximais ipsilaterais do fêmur ocorrem em 1 a 9% das fraturas diafisárias. Existem vários tratamentos propostos para essa associação lesional. O objetivo deste trabalho é rever os diferentes métodos de tratamento propostos, e comparar os seus resultados funcionais e principais complicações. Materiais e Métodos: Foram utilizados os buscadores eletrônicos: Pubmed, Lilacs, Cochrane e Ovid SP. A busca chegou a um total de 1829 trabalhos, dos quais foram selecionados 21 segundo critérios de inclusão e exclusão. Discussão: Não há consenso sobre qual é o melhor método de fixação para esta associação lesional. Esta ocorre em pacientes jovens por um mecanismo axial de alta energia cinética e a opção escolhida deve procurar a redução anatômica da fratura proximal do fêmur. Complicações como a pseudoartrose do pescoço femoral e a necrose avascular são de difícil manejo neste grupo etário. Conclusão: As fraturas ...(SUPRIMIR LO PRECEDENTE)Conclusão: As fracturas ipsilaterais proximais e diafisárias do fémur são lesões que apresentam um problema diagnóstico e terapêutico. Há um subdiagnóstico das mesmas e não existe um implante ideal, nem um consenso de qual é o melhor método de fixação.

Una Descripción General y Actualizada de Miniplacas y Minitornillos. Efectos Dentoalveolares y Esqueléticos / A General and Updated Description of Miniplates and Miniscrews. Dentoalveolar and Skeletal Effects

RESUMEN: En ortodoncia, las miniplacas se utilizan como dispositivo de anclaje temporal (TAD) para la realización de movimientos dentales que permiten el uso de fuerzas ortopédicas en ellos. En comparación con los mini tornillos, las miniplacas tienen la ventaja de una tasa de falla muy baja, pero la desventaja es que para la extracción se necesita el mismo acto quirúrgico que se realizó para la instalación. El objetivo de este estudio es realizar una revisión bibliográfica de las indicaciones de miniplacas en pacientes con mordidas abiertas, clase II y anomalías de clase III, y buscar cómo las miniplacas han mejorado los tratamientos de ortodoncia. La información principal se reunió buscando en PubMed con las palabras clave enumeradas a continuación. Afirmamos que las miniplacas están indicadas para la retracción en masa de la arcada, donde se observó que la fuerza de 150 g aplicada en los molares superiores es suficiente no solo para empujar los molares hacia atrás en una clase I corregida, sino también para iniciar la retracción de premolares, caninos e incisivos. En pacientes con mordida abierta, las miniplacas se definen como un método seguro, una alternativa rápida y menos costosa a la cirugía ortognática. Y en pacientes de las clases II y III se utilizan sin producir efectos dentoalveolares que sustituyan a los dispositivos extraorales como máscaras, con dispositivos intraorales y elásticos (BAMP).

ABSTRACT: In orthodontics, miniplates are used as a Temporary Anchoring Device (TAD) for the purpose dental movements, allowing the use of orthopedic forces. In comparison with mini-screws, miniplates have the advantage of a very low rate of failure. Nonetheless, their removal requires the same surgical procedure as during installation, which is an obvious disadvantage. The aim of this study is to review the indications of miniplates in patients with open bite, class II and class III anomalies, and review how miniplates improved orthodontics treatments. Information was obtained by a search in PubMed with the keywords listed below. Miniplates are indicated for retraction in mass of the arcade, where it was seen that the force of 150 g applied on maxillary molars, is sufficient not only to push the molars back into a corrected class I, but also to initiate retraction of premolars, canines, and incisors. In open-bite patients, mini plates, are achieved as a safe method, that is quick and a less expensive alternative to orthognathic surgery. Further, in class II and III patients they are used without producing dentoalveolar effects replacing extraoral devices as facemasks, with intraoral devices and elastics. (BAMP).