Instantaneous thermometry imaging using two-photon laser-induced fluorescence.

Measuring temperature in complex two-phase flows is crucial for understanding the dynamics of heat and mass transfer. In this Letter, we introduce a novel, to the best of our knowledge, optical approach based on the combination of two-photon laser-induced fluorescence (2p-LIF) imaging and two-color laser-induced fluorescence (2CLIF) for instantaneous temperature mapping of complex liquid media. Using Kiton Red (KR) and Rhodamine 560 (R560), a temperature sensitivity of 1.54%/∘C has been achieved over a range of 17-60°C. The monitoring of two-dimensional transient temperature dynamics in the heating and degassing of water shows the efficiency of the 2p-2CLIF. This new approach contributes to the toolkit of optical temperature measurement techniques, providing a robust solution for studying transient scattering media and high-speed two-phase flows.

Droplet sizing in atomizing sprays using polarization ratio with structured laser illumination planar imaging.

Previous research has shown that the polarization ratio technique allows the characterization of the surface mean diameter, D21, of droplets forming dilute sprays. However, its application to optically dense sprays has posed significant challenges due to the presence of multiple light scattering. Additionally, errors in measurement can arise from the angular dependence of the signal. In this Letter, we present a novel, to the best of our knowledge, method that addresses these challenges. Our approach combines the use of a telecentric objective with structured laser illumination, to both optimize light detection and suppress the unwanted intensity from multiple scattering. This approach enables the utilization of the polarization ratio technique for measuring the droplet size of challenging atomizing sprays. The method offers a promising solution for accurate and comprehensive spray characterization. It is applied, here, to a hollow-cone water spray running at 30, 50, and 70 bar injection pressure, reaching an optical depth up to three.

Multi-scattering software part II: experimental validation for the light intensity distribution.

This article, Part II of an article series on GPU-accelerated Monte Carlo simulation of photon transport through turbid media, focuses on the validation of the online software Multi-Scattering. While Part I detailed the implementation of the computational model, simulated and experimental results are now compared for the distribution of the scattered light intensity. The scattering phantoms prepared here are aqueous dispersions of polystyrene microspheres of diameter D = 0.5, 2 and 5 µm and at various concentrations, resulting in optical depth ranging from OD = 1 to 17.5. The Lorenz-Mie scattering phase functions used in the simulations have been verified experimentally at low particle concentrations by analyzing the angular light intensity distribution at the Fourier plane of a collecting lens. The validation approach herein accounts for the specific light collection and image formation by the camera. The front and side surfaces of the medium are imaged and the corresponding light intensity distributions are compared qualitatively and quantitatively. It is concluded that the model enables reliable simulations over the tested parameters, offering predictive simulations of transmitted intensities with a mean relative error ≤~19% over the full range. The online software is available at: https://multi-scattering.com/.

Transition from saliva droplets to solid aerosols in the context of COVID-19 spreading.

To control the evolution of a pandemic such as COVID-19, knowing the conditions under which the pathogen is being transmitted represents a critical issue, especially when implementing protection strategies such as social distancing and wearing face masks. For viruses and bacteria that spread via airborne and/or droplet pathways, this requires understanding how saliva droplets evolve over time after their expulsion by speaking or coughing. Within this context, the transition from saliva droplets to solid residues, due to water evaporation, is studied here both experimentally, considering the saliva from 5 men and 5 women, and via numerical modeling to accurately predict the dynamics of this process. The model assumes saliva to be a binary water/salt mixture and is validated against experimental results using saliva droplets that are suspended in an ultrasound levitator. We demonstrate that droplets with an initial diameter smaller than 21 µm will produce a solid residue that would be considered an aerosol of <5 µm diameter in less than 2 s (for any relative humidity less than 80% and/or any temperature greater than 20°C). Finally, the model developed here accounts for the influence of the saliva composition, relative humidity and ambient temperature on droplet drying. Thus, the travel distance prior to becoming a solid residue can be deduced. We found that saliva droplets of initial size below 80 µm, which corresponds to the vast majority of speech and cough droplets, will become solid residues prior to touching the ground when expelled from a height of 160 cm.

Stereoscopic high-speed imaging of iron microexplosions and nanoparticle-release.

In this work, the combustion behavior of seeded iron particles (d50 = 70 µm) in a laminar diffusion flame was studied in a modified Mckenna flat-flame burner. Two high speed cameras in stereo configuration allowed 3D position and 3D velocity measurements of burning iron particles as well as 3D evaluation of particle microexplosions. Microexplosive processes are important since it can affect both combustion stability and formation of product components. The observed microexplosions happened before particle extinction resulting in change of trajectories, velocities, radiation intensities and fragmentation into smaller particles. It was observed for the first time that fragments of these microexplosions tend to produce planar structures. A frequent release phenomenon was observed during the iron particle combustion using magnified thermal radiation imaging and high-speed shadowgraphy. This release phenomenon was indirectly confirmed with scanning electron microscopy of combust products, revealing multiple cracked particle shells and hollow structures. Black body radiation characteristics was observed indicating the release being in condensed phase and emission spectroscopy identified FeO as intermediate species during combustion. The observed release is believed to mainly consist of iron-oxide nanoparticles formed in the homogenous reaction between vapor iron and oxidizers.

Multi-Scattering software: part I: online accelerated Monte Carlo simulation of light transport through scattering media.

In this article we present and describe an online freely accessible software called Multi-Scattering for the modeling of light propagation in scattering and absorbing media. Part II of this article series focuses on the validation of the model by rigorously comparing the simulated results with experimental data. The model is based on the use of the Monte Carlo method, where billions of photon packets are being tracked through simulated cubic volumes. Simulations are accelerated by the use of general-purpose computing on graphics processing units, reducing the computation time by a factor up to 200x in comparison with a single central processing unit thread. By using four graphic cards on a single computer, the simulation speed increases by a factor of 800x. For an anisotropy factor g = 0.86, this enables the transport path of one billion photons to be computed in 10 seconds for optical depth OD = 10 and in 20 minutes for OD = 500. Another feature of Multi-Scattering is the integration and implementation of the Lorenz-Mie theory in the software to generate the scattering phase functions from spherical particles. The simulations are run from a computer server at Lund University, allowing researchers to log in and use it freely without any prior need for programming skills or specific software/hardware installations. There are countless types of scattering media in which this model can be used to predict light transport, including medical tissues, blood samples, clouds, smoke, fog, turbid liquids, spray systems, etc. An example of simulation results is given here for photon propagation through a piece of human head. The software also includes features for modeling image formation by inserting a virtual collecting lens and a detection matrix which simulate a camera objective and a sensor array respectively. The user interface for setting-up simulations and for displaying the corresponding results is found at: https://multi-scattering.com/.

Snapshot 3D reconstruction of liquid surfaces.

In contrast to static objects, liquid structures such as drops, blobs, as well as waves and ripples on water surfaces are challenging to image in 3D due to two main reasons: first, the transient nature of those phenomena requires snapshot imaging that is fast enough to freeze the motion of the liquid. Second, the transparency of liquids and the specular reflections from their surfaces induce complex image artefacts. In this article we present a novel imaging approach to reconstruct in 3D the surface of irregular liquid structures that only requires a single snapshot. The technique is named Fringe Projection - Laser Induced Fluorescence (FP-LIF) and uses a high concentration of fluorescent dye in the probed liquid. By exciting this dye with a fringe projection structured laser beam, fluorescence is generated primarily at the liquid surface and imaged at a backward angle. By analysing the deformation of the initial projected fringes using phase-demodulation image post-processing, the 3D coordinates of the liquid surface are deduced. In this article, the approach is first numerically tested by considering a simulated pending drop, in order to analyse its performance. Then, FP-LIF is applied for two experimental cases: a quasi-static pending drop as well as a transient liquid sheet. We demonstrate reconstruction RMS errors of 1.4% and 6.1% for the simulated and experimental cases respectively. The technique presented here demonstrates, for the first time, a fringe projection approach based on LIF detection to reconstruct liquid surfaces in 3D. FP-LIF is promising for the study of more complex liquid structures and is paving the way for high-speed 3D videography of liquid surfaces.

3D mapping of droplet Sauter mean diameter in sprays.

In this study, we report on the three-dimensional (3D) characterization of a spray in terms of its droplet Sauter mean diameter (SMD) using the laser-induced fluorescence (LIF)/Mie ratio technique. The spray structure is analyzed for a multi-hole direct-injection spark ignition (DISI) injector. A calibration curve to convert the LIF/Mie ratio to droplet diameter is deduced using LIF/Mie imaging and analysis of single droplets generated by a droplet generator. The DISI spray investigated here is optically sectioned by means of two-phase structured laser illumination planar imaging to suppress the intensity of multiple light scattering from LIF and Mie images prior to their ratio. A series of calibrated LIF/Mie ratio images of spray is then recorded at several depths along the z direction following the light sheet scanning of the spray. The droplet SMD ranges from less than 5 µm up to a maximum of 50 µm in single-shot images. The averaged SMD results (1-30 µm) obtained by using the calibration curve from the droplet generator are compared with measurement results from phase-Doppler anemometry. Finally, a 3D map is reconstructed from the successive 2D layers generated from spray scanning. The resulting 3D representation of the droplet SMD shows a non-symmetric spray structure produced by the studied multi-hole injector, which cannot be resolved by analyzing only one central plane.

Analysis of LIF and Mie signals from single micrometric droplets for instantaneous droplet sizing in sprays.

Planar droplet sizing (PDS) is a technique relying on the assumption that laser-induced fluorescence (LIF) and Mie scattering optical signals from spherical droplets depend on their volume and surface area, respectively. In this article, we verify the validity of this assumption by experimentally analyzing the light intensity of the LIF and Mie optical signals from micrometric droplets as a function of their diameter. The size of the droplets is controlled using a new flow-focusing monodisperse droplet generator capable of producing droplets of the desired size in the range of 21 µm to 60 µm. Ethanol droplets doped with eosin dye and excited at 532 nm are considered in this study, and the individual droplets were imaged simultaneously at microscopic and macroscopic scale. The effects of laser power, dye concentration, and temperature variation are systematically studied as a function of LIF/Mie ratio in the whole range of droplet sizes. Finally, a calibration curve at tracer concentration of 0.5 vol% is deduced and used to extract the droplet Sauter mean diameter (SMD) from instantaneous images of a transient ethanol spray. This droplet size mapping is done using structured laser illumination planar imaging (SLIPI), in order to suppress the artifacts induced by multiple light scattering.

Light sheet fluorescence microscopic imaging for the primary breakup of diesel and gasoline sprays with real-world fuels.

This paper describes the adaptation of the laser-induced fluorescence measurement technique for the investigation of the primary breakup of modern diesel and gasoline direct injection sprays. To investigate the primary breakup, a microscopic technique is required, and with the help of special tracer dyes, a high fluorescence signal can be achieved in the visible range of the electromagnetic spectrum, resulting in good image quality with a nonintensified camera. Besides the optimization of the optical setup for the microscopic field of view, different tracer dyes are compared, and their solubility and fluorescence are tested in the desired surrogate and real-world fuels. As a tracer, the phenoxazine dye Nile Red was found to provide sufficient solubility in alkanes as well as suitable emission and excitation spectrum for the use of the second-harmonic frequency of a Nd:YAG laser (532 nm). The good quantum efficiency delivered by Nile Red also meant that single-shot images clearly showing spray structures in regions measuring up to 3 mm by 3 mm around the nozzle outlet could be recorded. Compared to relatively easy shadowgraph techniques and complex and costly x-ray synchrotron measurements, light sheet fluorescence microscopic imaging is not overly complex yet delivers excellent data on spray structures as well as qualitative fuel distribution.

High dynamic spectroscopy using a digital micromirror device and periodic shadowing.

We present an optical solution called DMD-PS to boost the dynamic range of 2D imaging spectroscopic measurements up to 22 bits by incorporating a digital micromirror device (DMD) prior to detection in combination with the periodic shadowing (PS) approach. In contrast to high dynamic range (HDR), where the dynamic range is increased by recording several images at different exposure times, the current approach has the potential of improving the dynamic range from a single exposure and without saturation of the CCD sensor. In the procedure, the spectrum is imaged onto the DMD that selectively reduces the reflection from the intense spectral lines, allowing the signal from the weaker lines to be increased by a factor of 28 via longer exposure times, higher camera gains or increased laser power. This manipulation of the spectrum can either be based on a priori knowledge of the spectrum or by first performing a calibration measurement to sense the intensity distribution. The resulting benefits in detection sensitivity come, however, at the cost of strong generation of interfering stray light. To solve this issue the Periodic Shadowing technique, which is based on spatial light modulation, is also employed. In this proof-of-concept article we describe the full methodology of DMD-PS and demonstrate - using the calibration-based concept - an improvement in dynamic range by a factor of ~100 over conventional imaging spectroscopy. The dynamic range of the presented approach will directly benefit from future technological development of DMDs and camera sensors.

Quantitative measurements of turbid liquids via structured laser illumination planar imaging where absorption spectrophotometry fails.

A comparison between the commonly used absorption spectrophotometry and a more recent approach known as structured laser illumination planar imaging (SLIPI) is presented for the characterization of scattering and absorbing liquids. Water solutions of milk and coffee are, respectively, investigated for 10 different levels of turbidity. For the milk solutions, scattering is the dominant process, while the coffee solutions have a high level of absorption. Measurements of the extinction coefficient are performed at both λ=450 nm and λ=638 nm and the ratio of their values has been extracted. We show that the turbidity limit of valid transmission measurements is reached at an optical depth of OD∼2.4, corresponding here to an extinction coefficient of µe=0.60 mm-1 when using a modern absorption spectrometer having a spatial Fourier filter prior to detection. Above this value, errors are induced due to the contribution of scattered and multiply scattered photons reaching the detector. On the contrary, the SLIPI measurements were found to be very reliable, even for an extinction coefficient three times as high, where µe=1.80 mm-1. This improvement is due to the capability of the technique in efficiently suppressing the contribution from multiple light scattering.

Thermometry in aqueous solutions and sprays using two-color LIF and structured illumination.

In imaging, the detection of light originating from multiple scattering, indirect reflections and surrounding backgrounds are known to produce errors especially in intensity-ratio based measurements. SLIPI (Structured Laser Illumination Planar Imaging) is an imaging technique that significantly reduces the impact of such issues. In this study, SLIPI is combined with the two-color LIF (Laser Induced Fluorescence) ratio thermometry approach for measuring water temperature in both a cuvette and a hollow-cone spray. By removing the unwanted background interferences using SLIPI, we observe both significant improvements in terms of temperature sensitivity as well as more pronounced temperature gradients within the spray.

High-contrast imaging through scattering media using structured illumination and Fourier filtering.

We show in this Letter a novel approach for high-contrast imaging through scattering media by combining structured illumination and Fourier filtering (SIF). To assess the image contrast enhancement at different image spatial frequencies, the modulation transfer function is calculated for four detection schemes: (1) no filtering, (2) Fourier filtering, (3) structured illumination, and (4) SIF filtering. A scattering solution consisting of D=7.3 µm polystyrene spheres immersed in distilled water and illuminated at λ=671 nm is used here. We demonstrate the possibility of obtaining, with SIF, an image contrast up to 60% at an optical depth of OD=10, improving the contrast by a factor of 40 over conventional transmission imaging.

Two-phase SLIPI for instantaneous LIF and Mie imaging of transient fuel sprays.

We report in this Letter a two-phase structured laser illumination planar imaging [two-pulse SLIPI (2p-SLIPI)] optical setup where the "lines structure" is spatially shifted by exploiting the birefringence property of a calcite crystal. By using this optical component and two cross-polarized laser pulses, the shift of the modulated pattern is not "time-limited" anymore. Consequently, two sub-images with spatially mismatched phases can be recorded within a few hundred of nanoseconds only, freezing the motion of the illuminated transient flow. In comparison with previous setups for instantaneous imaging based on structured illumination, the current optical design presents the advantage of having a single optical path, greatly simplifying its complexity. Due to its virtue of suppressing the effects from multiple light scattering, the 2p-SLIPI technique is applied here in an optically dense multi-jet direct-injection spark-ignition (DISI) ethanol spray. The fast formation of polydispersed droplets and appearance of voids after fuel injection are investigated by simultaneous detection of Mie scattering and liquid laser-induced fluorescence. The results allow for significantly improved analysis of the spray structure.

Reliable LIF/Mie droplet sizing in sprays using structured laser illumination planar imaging.

In this article, Structured Laser Illumination Planar Imaging (SLIPI) is used in combination with the LIF/Mie ratio technique for extracting a reliable two-dimensional mapping of the droplets Sauter Mean Diameter (SMD). We show that even for the case of a fairly dilute spray, where single scattering events are in majority, the conventional LIF/Mie technique still remains largely affected by errors introduced by multiple light scattering. To remove this unwanted light intensity on both the LIF and Mie images SLIPI is used prior to apply the image ratio. For the first time, the SLIPI LIF/Mie results are calibrated and compared with measurement data from Phase Doppler Interferometry (PDI).

Stray light suppression in spectroscopy using periodic shadowing.

It is well known that spectroscopic measurements suffer from an interference known as stray light, causing spectral distortion that reduces measurement accuracy. In severe situations, stray light may even obscure the existence of spectral lines. Here a novel general method is presented, named Periodic Shadowing, that enables effective stray light elimination in spectroscopy and experimental results are provided to demonstrate its capabilities and versatility. Besides its efficiency, implementing it in a spectroscopic arrangement comes at virtually no added experimental complexity.

Two-pulse structured illumination imaging.

Structured illumination (SI), which is an imaging technique that is employed in a variety of fields, permits unique possibilities to suppress unwanted signal contributions that carry misguiding information such as out-of-focus light or multiply scattered light. So far SI has been applied mostly for averaged imaging or for imaging of slowly occurring events because it requires three acquisitions (subimages) to construct the final SI image. This prerequisite puts technological constraints on SI that make "instantaneous" imaging of fast transient processes (occurring on submicrosecond time scales) very challenging and expensive. Operating SI with fewer subimages generates errors in the form of residual lines that stretch across the image. Here, a new approach that circumvents this limiting factor is presented and experimentally demonstrated. By judiciously choosing the intensity modulation, it is possible to extract an SI image from two subimages only. This development will allow standard double-pulsed lasers and interline transfer CCD or scientific CMOS cameras to be used to acquire temporally frozen SI images of rapidly occurring processes as well as to boost the frame-rate of current SI video systems; a technical advancement that will benefit both macro- and microscopic imaging applications.

Image post-processing for SILMAS: structured illumination light sheet microscopy with axial sweeping.

In this article, we propose a post-processing scheme for the novel volumetric microscopy technique SILMAS. We demonstrate this scheme on data from an alpha-synuclein transgenic mouse brain. By combining structured illumination and axial sweeping, a SILMAS measurement provides a prerequisite for quantitative data extraction through improved contrast and optical sectioning. However, due to the technique's efficient removal ofb multiple scattered light, image artifacts such as illumination inhomogeneity, shadowing stripes, and signal attenuation, are highlighted in the recorded volumes. To suppress these artifacts, we rely on the strengths of the imaging method. The SILMAS data, together with the Beer-Lambert law, allow for an approximation of real light extinction, which can be used to compensate for light attenuation in a near-quantitative way. Shadowing stripes can be suppressed efficiently using a computational strategy thanks to the large numerical aperture of an axially swept light sheet. Here, we build upon prior research that employed wavelet-Fourier filtering by incorporating an extra bandpass step. This allows us to filter high-contrast light sheet microscopy data without introducing new artifacts and with minimal distortion of the data. The combined technique is suitable for imaging cleared tissue samples of up to a centimeter scale with an isotropic resolution of a few microns. The combination of a thin and uniform light sheet, scattered light suppression, light attenuation compensation, and shadowing suppression produces volumetric data that is seamless and highly uniform.

High-Speed Fluorescence Imaging Corroborates Biological Data on the Influence of Different Nozzle Types on Cell Spray Viability and Formation.

Treating severe dermal disruptions often presents significant challenges. Recent advancements have explored biological cell sprays as a promising treatment, but their success hinges on efficient cell delivery and complete wound coverage. This requires a good spray distribution with a small droplet size, high particle number, and ample surface coverage. The type of nozzle used with the spray device can impact these parameters. To evaluate the influence of different nozzles on spray characteristics, we compared air-assisted and unassisted nozzles. The unassisted nozzle displayed small particle size, high particle number, good overall coverage, high cell viability, preserved cell metabolic activity, and low cytotoxicity. Air-assisted nozzles did not perform well regarding cell viability and metabolic activity. Flow visualization analysis comparing two different unassisted nozzles using high-speed imaging (100 kHz frame rate) revealed a tulip-shaped spray pattern, indicating optimal spray distribution. High-speed imaging showed differences between the unassisted nozzles. One unassisted nozzle displayed a bi-modal distribution of the droplet diameter while the other unassisted nozzle displayed a mono-modal distribution. These findings demonstrate the critical role of nozzle selection in successful cell delivery. A high-quality, certified nozzle manufactured for human application omits the need for an air-assisted nozzle and provides a simple system to use with similar or better performance characteristics than those of an air-assisted system.