Low-temperature thermocatalytic removal of formaldehyde in air using copper manganite spinels.

The removal of formaldehyde (FA) is vital for indoor air quality management in light of its carcinogenic propensity and adverse environmental impact. A series of copper manganite spinel structures (e.g., CuMn2O4) are prepared using the sol-gel combustion method and treated with reduction or oxidation pretreatment at 300 °C condition. Accordingly, CuMn2O4-O ("O" suffix for oxidation pre-treatment in air) is identified as the best performer to achieve 100% conversion (XFA) of FA (50 ppm) at 90 °C; its performance, if assessed in terms of reaction kinetic rate (r) at XFA = 10%, is 5.02E-03 mmol g-1 h-1. The FA removal performance increases systematically with decreases in flow rate, FA concentration, and relative humidity (RH) or with increases in bed mass. The reaction pathways and intermediates of FA catalytic oxidation on CuMn2O4-A are studied with density functional theory simulations, temperature-programmed characterization experiments, and in-situ diffuse reflectance infrared Fourier transform spectroscopy. The synergistic combination of large quantities of adsorbed oxygen (OA) species and oxidized metal species (e.g., Cu2+) contribute to the enhanced catalytic performance of CuMn2O4-O to oxidize FA into CO2 with the reaction intermediates of H2CO2 (DOM), HCOO-, and CO. The present study is expected to provide valuable insights into the thermocatalytic oxidation of FA over spinel CuMn2O4 materials and their catalytic performances in relation to the key process variables.

Unlocking Giant Third-Order Optical Nonlinearity in (MA)2CuX4 through Introducing Jahn-Teller Distortion.

Nonlinear absorption coefficient and modulation depth stand as pivotal properties of nonlinear optical (NLO) materials, while the existing NLO materials exhibit limitations such as low nonlinear absorption coefficients and/or small modulation depths, thereby severely impeding their practical application. Here we unveil that introducing Jahn-Teller distortion in a Mott-Hubbard system, (MA)2CuX4 (MA=methylammonium; X=Cl, Br) affords the simultaneous attainment of a giant nonlinear absorption coefficient and substantial modulation depth. The optimized compound, (MA)2CuCl4, demonstrates a nonlinear absorption coefficient of (1.5±0.08)×105 cm GW-1, a modulation depth of 60 %, and a relatively low optical limiting threshold of 1.22×10-5 J cm-2. These outstanding attributes surpass those of most reported NLO materials. Our investigation reveals that a more pronounced distortion of the [CuX6]4- octahedron emerges as a crucial factor in augmenting optical nonlinearity. Mechanism study involving structural and spectral characterization along with theoretical calculations indicates a correlation between the compelling performance and the Mott-Hubbard band structure of the materials, coupled with the Jahn-Teller distortion-induced d-d transition. This study not only introduces a promising category of high-performance NLO materials but also provides novel insights into enhancing the performance of such materials.

NiSe and CoSe Topological Nodal-Line Semimetals: A Sustainable Platform for Efficient Thermoplasmonics and Solar-Driven Photothermal Membrane Distillation.

The control of heat at the nanoscale via the excitation of localized surface plasmons in nanoparticles (NPs) irradiated with light holds great potential in several fields (cancer therapy, catalysis, desalination). To date, most thermoplasmonic applications are based on Ag and Au NPs, whose cost of raw materials inevitably limits the scalability for industrial applications requiring large amounts of photothermal NPs, as in the case of desalination plants. On the other hand, alternative nanomaterials proposed so far exhibit severe restrictions associated with the insufficient photothermal efficacy in the visible, the poor chemical stability, and the challenging scalability. Here, it is demonstrated the outstanding potential of NiSe and CoSe topological nodal-line semimetals for thermoplasmonics. The anisotropic dielectric properties of NiSe and CoSe activate additional plasmonic resonances. Specifically, NiSe and CoSe NPs support multiple localized surface plasmons in the optical range, resulting in a broadband matching with sunlight radiation spectrum. Finally, it is validated the proposed NiSe and CoSe-based thermoplasmonic platform by implementing solar-driven membrane distillation by adopting NiSe and CoSe nanofillers embedded in a polymeric membrane for seawater desalination. Remarkably, replacing Ag with NiSe and CoSe for solar membrane distillation increases the transmembrane flux by 330% and 690%, respectively. Correspondingly, costs of raw materials are also reduced by 24 and 11 times, respectively. The results pave the way for the advent of NiSe and CoSe for efficient and sustainable thermoplasmonics and related applications exploiting sunlight within the paradigm of the circular blue economy.

A new aggregation induced emission enhancement (AIEE) dye which self-assembles to panchromatic fluorescent flowers and has application in sensing dichromate ions.

We report for the very first time the crystal structure and self-assembly of a new aggregation-induced emission enhancement (AIEE) dye 4-(5-methoxythiazolo[4,5-b]pyridin-2-yl)-N,N-dimethylaniline (TPA) and its application in sensing dichromate ions. TPA reveals cyan blue emission under UV and visible light. The self-assembly properties of TPA were studied extensively by scanning electron microscopy (SEM) which revealed the formation of beautiful flower-like morphologies. These structures revealed both green and red fluorescence under FITC and rhodamine filters respectively when observed through fluorescence microscopy connoting the panchromatic emission properties of TPA from blue to red. The interactions which cause self-assembled structure formation in TPA were also validated theoretically using density functional theory (DFT) calculations. Crystal and molecular structure analysis of TPA was carried out via single-crystal X-ray diffraction to visualize the intermolecular interactions occurring in the solid-state and to study the structure-photophysical property relationship in the aggregated state. The photophysical properties of TPA were also studied extensively by UV-visible and fluorescence spectroscopy and its quantum yield and fluorescence lifetime were calculated by time-correlated single-photon counting (TCSPC). Interestingly, TPA could efficiently sense dichromate (Cr2O72-) ions in an acidic medium and an interesting morphological transition from a fluorescent flower to non-fluorescent disassembled structures could also be observed. The limit of detection of TPA for Cr2O72- ions was found to be as low as 5.5 nM, suggesting its exceptional sensitivity. More importantly, TPA could selectively sense Cr2O72- ions in real water samples even in the presence of other metal ions routinely present in polluted water, hence making it practically useful for water quality monitoring.

On the atomic structure of two-dimensional materials with Janus structures.

The discrepancy between the bright theoretical projections for two-dimensional (2D) Janus structures and the lack of experimental realisation of these structures motivated us to study the effect of structural disorder on the stability of MoSSe, SnSSe, PtSSe, In2SSe and GaInSe2. The calculation results demonstrate that the difference between metal-sulfur and metal-selenium bonds makes Janus structures frustrated and less energetically favourable than less ordered allotropes of the same compounds. This result explains the difficulties encountered in the experimental fabrication of these materials. In the bulk, there is an additional contribution to the total energy from dipole-dipole interactions between layers with a Janus structure that can overcome the energetic cost of structural frustration in layers for compounds with sufficiently large dipole moments. However, the entropic contribution to the free energy decreases the favourability of the ordered Janus structure. The calculation results are used to make recommendations to enable the discovery and synthesis of 2D materials with Janus structures.

Chemical reactions on surfaces for applications in catalysis, gas sensing, adsorption-assisted desalination and Li-ion batteries: opportunities and challenges for surface science.

The study of chemical processes on solid surfaces is a powerful tool to discover novel physicochemical concepts with direct implications for processes based on chemical reactions at surfaces, largely exploited by industry. Recent upgrades of experimental tools and computational capabilities, as well as the advent of two-dimensional materials, have opened new opportunities and challenges for surface science. In this Perspective, we highlight recent advances in application fields strictly connected to novel concepts emerging in surface science. Specifically, we show for selected case-study examples that surface oxidation can be unexpectedly beneficial for improving the efficiency in electrocatalysis (the hydrogen evolution reaction and oxygen evolution reaction) and photocatalysis, as well as in gas sensing. Moreover, we discuss the adsorption-assisted mechanism in membrane distillation for seawater desalination, as well as the use of surface-science tools in the study of Li-ion batteries. In all these applications, surface-science methodologies (both experimental and theoretical) have unveiled new physicochemical processes, whose efficiency can be further tuned by controlling surface phenomena, thus paving the way for a new era for the investigation of surfaces and interfaces of nanomaterials. In addition, we discuss the role of surface scientists in contemporary condensed matter physics, taking as case-study examples specific controversial debates concerning unexpected phenomena emerging in nanosheets of layered materials, solved by adopting a surface-science approach.

Thermal Effects and Halide Mixing of Hybrid Perovskites: MD and XPS Studies.

Thermal effects in organo-metal halide perovskites are studied by ab initio molecular dynamics (MD) simulations performed at effective temperatures of 293 and 383 K and by X-ray photoelectron spectroscopy (XPS). We find that the cause of thermal instability in this class of perovskites is the rotation of the methylammonium (MA) groups that destroy the rigid lattice of pure compounds (MAPbI3 and MAPbBr3). When the Pb-I lattice is initially distorted by partial replacement of the I with Cl or Br, this not only prevents formation of PbI2 seeds but also improves lattice flexibility and stability against the temperature-induced motion and rotation of MA groups.

Structural phase transitions in VSe2: energetics, electronic structure and magnetism.

First principles calculations of the magnetic and electronic properties of VSe2 describing the transition between two structural phases (H,T) were performed. The results of the calculations evidence a rather low energy barrier (0.60 eV for the monolayer) for the transition between the phases. The energy required for the deviation of a Se atom or whole layer of selenium atoms by a small angle of up to 10° from their initial positions is also rather low, 0.32 and 0.19 eV/Se, respectively. The changes in the band structure of VSe2 caused by these motions of Se atoms should be taken into account for analysis of the experimental data. Simulations of the strain effects suggest that the experimentally observed T phase of the VSe2 monolayer is the ground state due to substrate-induced strain. Calculations of the difference in the total energies of the ferromagnetic and antiferromagnetic configurations evidence that the ferromagnetic configuration is the ground state of the system for all stable and intermediate atomic structures. Calculated phonon dispersions suggest a visible influence of the magnetic configurations on the vibrational properties.

Liquid-Phase Exfoliated Indium-Selenide Flakes and Their Application in Hydrogen Evolution Reaction.

Single- and few-layered InSe flakes are produced by the liquid-phase exfoliation of ß-InSe single crystals in 2-propanol, obtaining stable dispersions with a concentration as high as 0.11 g L-1 . Ultracentrifugation is used to tune the morphology, i.e., the lateral size and thickness of the as-produced InSe flakes. It is demonstrated that the obtained InSe flakes have maximum lateral sizes ranging from 30 nm to a few micrometers, and thicknesses ranging from 1 to 20 nm, with a maximum population centered at ≈5 nm, corresponding to 4 Se-In-In-Se quaternary layers. It is also shown that no formation of further InSe-based compounds (such as In2 Se3 ) or oxides occurs during the exfoliation process. The potential of these exfoliated-InSe few-layer flakes as a catalyst for the hydrogen evolution reaction (HER) is tested in hybrid single-walled carbon nanotubes/InSe heterostructures. The dependence of the InSe flakes' morphologies, i.e., surface area and thickness, on the HER performances is highlighted, achieving the best efficiencies with small flakes offering predominant edge effects. The theoretical model unveils the origin of the catalytic efficiency of InSe flakes, and correlates the catalytic activity to the Se vacancies at the edge of the flakes.

Absence of a stable atomic structure in fluorinated graphene.

Based on the results of first-principles calculations we demonstrate that significant distortion of graphene sheets caused by adsorption of fluorine atoms leads to the formation of metastable patterns for which the next step of fluorination is considerably less energetically favorable. Existence of these stable patterns oriented along the armchair direction makes possible the synthesis of various CFx structures. The combination of strong distortion of the nonfluorinated graphene sheet with the doping caused by the polar nature of C-F bonds reduces the energy cost of migration and the energy of migration barriers, making possible the migration of fluorine atoms on the graphene surface as well as transformation of the shapes of fluorinated areas. The decreasing energy cost of migration with increasing fluorine content also leads to increasing numbers of single fluorine adatoms, which could be the source of magnetic moments.

The atomic and electronic structure of nitrogen- and boron-doped phosphorene.

First principles modeling of nitrogen- and boron-doped phosphorene demonstrates the tendency toward the formation of highly ordered structures. Nitrogen doping leads to the formation of -N-P-P-P-N- lines. Further transformation into -P-N-P-N- lines across the chains of phosphorene occurs with increasing band gap and increasing nitrogen concentration, which coincides with the decreasing chemical activity of N-doped phosphorene. In contrast to the case of nitrogen, boron atoms prefer to form -B-B- pairs with the further formation of -P-P-B-B-P-P- patterns along the phosphorene chains. The low concentration of boron dopants converts the phosphorene from a semiconductor into a semimetal with the simultaneous enhancement of its chemical activity. Co-doping of phosphorene by both boron and nitrogen starts from the formation of -B-N- pairs, which provides flat bands and further transformation of these pairs into hexagonal BN lines and ribbons across the phosphorene chains.

Origin of anomalous water permeation through graphene oxide membrane.

Water inside the low-dimensional carbon structures has been considered seriously owing to fundamental interest in its flow and structures as well as its practical impact. Recently, the anomalous perfect penetration of water through graphene oxide membrane was demonstrated although the membrane was impenetrable for other liquids and even gases. The unusual auxetic behavior of graphene oxide in the presence of water was also reported. Here, on the basis of first-principles calculations, we establish atomistic models for hybrid systems composed of water and graphene oxides revealing the anomalous water behavior inside the stacked graphene oxides. We show that formation of hexagonal ice bilayer in between the flakes as well as melting transition of ice at the edges of flakes are crucial to realize the perfect water permeation across the whole stacked structures. The distance between adjacent layers that can be controlled either by oxygen reduction process or pressure is shown to determine the water flow thus highlighting a unique water dynamics in randomly connected two-dimensional spaces.

Benzene Oxidation in Air by an Amine-Functionalized Metal-Organic Framework-Derived Carbon- and Nitrogen-Loaded Zirconium Dioxide-Supported Platinum Catalyst.

To learn more about the behavior of amine (NH2)-functionalized metal-organic framework (MOF)-derived noble metal catalysts in the removal of aromatic volatile organic compounds in air, benzene oxidation at low temperatures has been investigated using 0.2-, 0.8-, and 1.5%-platinum (Pt)/Universitetet i Oslo (UiO)-66-NH2. The benzene conversion (XB) of x%-Pt/UiO-66-NH2-R under dry conditions (175 °C) was 23% (x = 0.2%) < 52% (x = 0.8%) < 100% (x = 1.5%): 'R' suffix denotes reduction pretreatment using a hydrogen (10 vol %) and nitrogen mixture at 300 °C for the generation of metallic Pt (Pt0) sites and simultaneous partial MOF decomposition into carbon- and nitrogen-loaded zirconium dioxide. The prominent role of reduction pretreatment was apparent in benzene oxidation as 1.5%-Pt/UiO-66-NH2 did not exhibit catalytic activity below 175 °C (dry condition). The promotional role of moisture in benzene oxidation by 1.5%-Pt/UiO-66-NH2-R was evident with a rise in the steady-state reaction rate (r) at 110 °C (21 kPa molecular oxygen (O2)) from 1.3 × 10-3 to 5.0 × 10-3 µmol g-1 s-1 as the water (H2O) partial pressure increased from 0 to 1.88 kPa. In contrast, the activity was lowered with increasing RH due to catalyst poisoning by excess moisture (r (110 °C) of 6.6 × 10-04 µmol g-1 s-1 at 2.83 kPa H2O (21 kPa O2)). Kinetic modeling suggests that XB proceeds through the Langmuir-Hinshelwood mechanism on the Pt/UiO-66-NH2-R surface (dissociative O2 chemisorption and the involvement of two oxygen species in benzene oxidation). According to the density functional theory simulation, the carbon and nitrogen impurities are to make the first XB step (i.e., hydrogen migration from the benzene molecule to the substrate) energetically favorable. The second hydrogen atom from the benzene molecule is also extracted effectively, while the oxygen derived from O2 facilitates further XB. The Pt0 sites dissociate the O2 and H2O molecules, while the product of the latter, i.e., free hydrogen and hydroxyl, makes the subsequent XB steps energetically favorable.

Titanium dioxide-supported mercury photocatalysts for oxidative removal of hydrogen sulfide from the air using a portable air purification unit.

Photocatalytic removal of gaseous hydrogen sulfide (H2S) has been studied through the control of key process variables using a prototype air purifier (AP) fabricated with titanium dioxide (TiO2)-supported mercury. The performance of Hg/TiO2 systems, prepared with different Hg mass proportions over TiO2 (such as 0.1%, 1%, 2%, and 5%), is measured against 5 ppm H2S at 160 L min-1 under UV irradiation. Accordingly, their removal efficiency (RE) values after 360 s are 40.3%, 74.8%, 99.3%, and 99.9%, respectively (relative to 33.5% of AP (TiO2)). An AP with a 2% Hg/TiO2 unit achieves a clean air delivery rate of 32 L min-1 with kinetic reaction rate (r (at 10% RE)) of 0.774 mmol h-1 g-1, quantum yield of 2.19E-02 molecules photon-1, and space-time yield of 1.46E-04 molecules photon-1 mg-1. The superior photocatalytic performance of Hg/TiO2 is supported by superoxide anion and hydroxyl radicals formed in dry air and humid nitrogen (N2) environments, respectively. A density functional theory simulation suggests that the presence of oxygen vacancies should promote the disparities in the electronic structure to subsequently affect the reaction pathways and energetics. The presence of moisture enhances the robust formation of a mercury-OH bond to favorably yield ß-mercury sulfide from H2S.

Enhancing Oxygen Evolution Reaction Performance of Metal-Organic Frameworks through Cathode Activation.

Due to their abundant active sites and porous structures, metal-organic frameworks (MOFs) have garnered significant interest as oxygen evolution reaction (OER) electrocatalysts. Nevertheless, the development of MOF-based electrocatalysts with efficient OER activity and excellent stability simultaneously still faces challenges. Herein, a cathodic activation strategy was used to enhance the OER electrocatalytic performance of M-HHTP for the first time, where M refers to Ni, Cu, Co, Fe, while HHTP denotes 2, 3, 6, 7, 10, 11-hexahydroxytriphenylene. As a prototype, the activated Ni-HHTP (HA-Ni-HHTP) demonstrates outstanding OER performance, with an overpotential as low as 140 mV at 20 mA cm-2 and a small Tafel slope of 78.7 mV-1, surpassing commercial RuO2 and rivaling state-of-the-art MOFs-based electrocatalysts. Characterizations and density functional theory calculations reveal that the superior performance of HA-Ni-HHTP is primarily ascribed to changes in semiconductor type, contact angle, and oxygen vacancy content induced by cathodic activation. Electrochemical impedance spectroscopy analysis using the transmission line model confirms that cathodic activation accelerates charge transport, enhancing the OER process. Furthermore, the cathodic activation strategy holds promise for improving the water oxidation performance of other MOFs such as Fe-HHTP, Co-HHTP, and Cu-HHTP.

The catalytic efficacy of modified manganese-cobalt oxides for room-temperature oxidation of formaldehyde in air.

Formaldehyde (FA) is a hazardous indoor air pollutant with carcinogenic propensity. Oxidation of FA in the dark at low temperature (DLT) is a promising strategy for its elimination from indoor air. In this light, binary manganese-cobalt oxide (0.1 to 5 mol L-1-MnCo2O4) is synthesized and modified in an alkaline medium (0.1-5 mol L-1 potassium hydroxide) for FA oxidation under room temperature (RT) conditions. Accordingly, 1-MnCo2O4 achieves 100 % FA conversion at RT (50 ppm and 7022 h-1 gas hourly space velocity (GHSV)). The catalytic activity of 1-MnCo2O4 is assessed further as a function of diverse variables (e.g., catalyst mass, relative humidity, FA concentration, molecular oxygen (O2) content, flow rate, and time on-stream). In situ diffuse reflectance infrared Fourier-transform spectroscopy confirms that FA molecules are adsorbed onto the active surface sites of 1-MnCo2O4 and oxidized into water (H2O) and carbon dioxide (CO2) through dioxymethylene (DOM) and formate (HCOO-) as the reaction intermediates. According to the density functional theory simulations, the higher catalytic activity of 1-MnCo2O4 can be attributed to the combined effects of its meritful surface properties (e.g., the firmer attachment of FA molecules, lower energy cost of FA adsorption, and lower desorption energy for CO2 and H2O). This work is the first report on the synthesis of alkali (KOH)-modified MnCo2O4 and its application toward the FA oxidative removal at RT in the dark. The results of this study are expected to provide valuable insights into the development of efficient and cost-effective non-noble metal catalysts against indoor FA at DLT.

Thermocatalytic oxidation of a binary mixture of formaldehyde and toluene at ambient levels by a titanium dioxide supported platinum catalyst.

The thermocatalytic oxidative potential of various supported noble metal catalysts (SNMCs) is well-known for hazardous volatile organic compounds (VOCs), e.g., formaldehyde (FA) and toluene. However, little is known about SNMC performance against ambient VOC pollution with low concentration (subppm levels) relative to industrial effuluents with high concentrations (several hundred ppm). Here, the thermocatalytic oxidation performance of a titanium dioxide (TiO2)-supported platinum catalyst (Pt/TiO2) has been evaluated for a low-concentration binary mixture of FA and toluene at low temperatures and in the dark. A sample of TiO2 containing 1 wt% Pt with thermal reduction pre-treatment under hydrogen achieved 100 % conversion of FA (500 ppb) and toluene (100 ppb) at 130 °C and a gas hourly velocity of 59,701 h-1. Its catalytic activity was lowered by either a decrease in catalyst mass or an increase in VOC concentration, relative humidity, or flow rate. In situ diffuse reflectance infrared Fourier transform spectroscopy, density functional theory simulations, and molecular oxygen (O2) temperature-programmed desorption experiments were used to identify possible VOC oxidation pathways, reaction mechanisms, and associated surface phenomena. The present work is expected to offer insights into the utility of metal oxide-supported Pt catalysts for the low-temperature oxidative removal of gaseous VOCs in the dark, primarily for indoor air quality management.

The practical utility of ternary nickel-cobalt-manganese oxide-supported platinum catalysts for room-temperature oxidative removal of formaldehyde from the air.

Formaldehyde (FA), a carcinogenic oxygenated volatile organic compound, is present ubiquitously in indoor air. As such, it is generally regarded as a critical target for air quality management. The oxidative removal of FA under dark and room-temperature (RT) conditions is of practical significance. A series of ternary nickel-cobalt-manganese oxide-supported platinum catalysts (Pt/NiCoMnO4) have been synthesized for FA oxidative removal at RT in the dark. Their RT conversion values for 50 ppm FA (XFA) at 5,964 h-1 gas hourly space velocity (GHSV) decrease in the following order: 1 wt% Pt/NiCoMnO4 (100 %) > 0.5 wt% Pt/NiCoMnO4 (25 %) > 0.05 wt% Pt/NiCoMnO4 (14 %) > NiCoMnO4 (6 %). The catalytic performance of 1 wt% Pt/NiCoMnO4 has been examined further under the control of various process variables (e.g., catalyst mass, flow rate, relative humidity, FA concentration, time on stream, and molecular oxygen content). The catalytic oxidation of FA at low temperatures (e.g., RT and 60 °C) is accounted for by Langmuir-Hinshelwood mechanism (single-site competitive-adsorption), while Mars van Krevelen kinetics is prevalent at higher temperatures. In situ diffuse-reflectance infrared Fourier-transform spectroscopy reveals that FA oxidation proceeds through a series of reaction intermediates such as DOM, HCOO-, and CO32-. Based on the density functional theory simulations, the unique electronic structures of the nearest surface atoms (platinum and nickel) are suggested to be responsible for the superior catalytic activity of Pt/NiCoMnO4.

Hydrogen dissociation catalyzed by carbon-coated nickel nanoparticles: experiment and theory.

Based on the combination of experimental measurements and first-principles calculations we report a novel carbon-based catalytic material and describe significant acceleration of the hydrogenation of magnesium at room temperature in the presence of nickel nanoparticles wrapped in multilayer graphene. The increase in rate of magnesium hydrogenation in contrast to a mix of graphite and nickel nanoparticles evidences intrinsic catalytic properties of the nanocomposites explored. The results from simulation demonstrate that doping of the metal substrate and the presence of Stone-Wales defects turn multilayer graphene from being chemically inert to chemically active. The role of the size of the nanoparticles and temperature are also discussed.

Isolated Spin-7/2 Species of Gadolinium (III) Chelate Complexes on the Surface of 5-nm Diamond Particles.

The magnetic characteristics of a system of triply charged gadolinium ions Gd3+ chelated with carboxyls on the surface of detonation nanodiamond (DND) particles have been studied. Gd3+ ions demonstrate almost perfect spin (S = 7/2) paramagnetism with negligible antiferromagnetic interaction between spins (Weiss temperature about -0.35 K) for a wide range of concentrations up to ~18 ions per 5 nm particle. The study of the concentration dependence of the electron paramagnetic resonance signal for DND intrinsic defects with spin ½ (g = 2.0027) shows that Gd3+ ions are located on average at a distance of no more than 1.4 nm from shallow subsurface defects with spin 1/2. At the same time, they are located (according to density functional theory calculations) at a distance of about or at least 0.28 nm from the particle surface. Magnetic studies also confirm the isolated nature of the gadolinium chelate complexes on the surface of DND particles. DND particles turn out to be an optimal carrier for high-spin 4f- ions (gadolinium) in a highly concentrated isolated state. This property makes DND-Gd particles a candidate for the role of a contrast agent for magnetic resonance imaging.