Highly Reproducible Large-Area Perovskite Solar Cell Fabrication via Continuous Megasonic Spray Coating of CH3 NH3 PbI3.

A simple, low-cost, large area, and continuous scalable coating method is proposed for the fabrication of hybrid organic-inorganic perovskite solar cells. A megasonic spray-coating method utilizing a 1.7 MHz megasonic nebulizer that could fabricate reproducible large-area planar efficient perovskite films is developed. The coating method fabricates uniform large-area perovskite film with large-sized grain since smaller and narrower sized mist droplets than those generated by existing ultrasonic spray methods could be generated by megasonic spraying. The volume flow rate of the CH3 NH3 PbI3 precursor solution and the reaction temperature are controlled, to obtain a high quality perovskite active layer. The devices reach a maximum efficiency of 16.9%, with an average efficiency of 16.4% from 21 samples. The applicability of megasonic spray coating to the fabrication of large-area solar cells (1 cm2 ), with a power conversion efficiency of 14.2%, is also demonstrated. This is a record high efficiency for large-area perovskite solar cells fabricated by continuous spray coating.

Strongly Coupled Cyclometalated Ruthenium Triarylamine Chromophores as Sensitizers for DSSCs.

A series of anchor-functionalized cyclometalated bis(tridentate) ruthenium(II) triarylamine hybrids [Ru(dbp-X)(tctpy)](2-) [2 a](2-) -[2 c](2-) (H3 tctpy=2,2';6',2''-terpyridine-4,4',4''-tricarboxylic acid; dpbH=1,3-dipyridylbenzene; X=N(4-C6 H4 OMe)2 ([2 a](2-) ), NPh2 ([2 b](2-) ), N-carbazolyl [2 c](2-) ) was synthesized and characterized. All complexes show broad absorption bands in the range 300-700 nm with a maximum at about 545 nm. Methyl esters [Ru(Me3 tctpy)(dpb-X)](+) [1 a](+) -[1 c](+) are oxidized to the strongly coupled mixed-valent species [1 a](2+) -[1 c](2+) and the Ru(III) (aminium) complexes [1 a](3+) -[1 c](3+) at comparably low oxidation potentials. Theoretical calculations suggest an increasing spin delocalization between the metal center and the triarylamine unit in the order [1 a](2+) <[1 b](2+) <[1 c](2+) . Solar cells were prepared with the saponified complexes [2 a](2-) -[2 c](2-) and the reference dye N719 as sensitizers using the I3 (-) /I(-) couple and [Co(bpy)3 ](3+/2+) and [Co(ddpd)2 ](3+/2+) couples as [B(C6 F5 )4 ](-) salts as electrolytes (bpy=2,2'-bipyridine; ddpd=N,N'-dimethyl-N,N'-dipyridin-2-yl-pyridine-2,6-diamine). Cells with [2 c](2-) and I3 (-) /I(-) electrolyte perform similarly to cells with N719. In the presence of cobalt electrolytes, all efficiencies are reduced, yet under these conditions [2 c](2-) outperforms N719.

Successful demonstration of an efficient I(-)/(SeCN)2 redox mediator for dye-sensitized solar cells.

A new I(-)/(SeCN)(2) redox mediator has favorable properties for dye-sensitized solar cells (DSCs) such as less visible light absorption, higher ionic conductivity, and downward shift of redox potential than I(-)/I(3)(-). It was then applied for DSCs towards increasing energy conversion efficiency, giving a new potential for improving performance.

Potential of self-drilling orthodontic microimplants under immediate loading.

INTRODUCTION: The aim of this study was to investigate clinically and histologically the efficiency of self-drilling microimplants as orthodontic anchorage with immediate, continuous, and constant loadings. METHODS: Titanium-alloy microimplants with diameters of 1.2 to 1.3mm were manually placed into the buccal sides of both jaws, including the interradicular areas, in 3 dogs. Implants were placed without predrilling in thin cortical bone areas; in thick cortical bone areas, a 2-mm deep pilot hole was drilled. Thirty-six microimplants, subjected to approximately 200g of immediate horizontal loading, served as the study group. The remaining 8 received no loading and were the controls over the 9-week observation period. The distances of reciprocally loaded microimplants and crevicular pockets were measured at the beginning and end of loading. Serially undecalcified and decalcified sections of the microimplants and surrounding tissues were studied with light and fluorescent microscopes. After 9 weeks of observation, 22 fixtures were easily removed with a screwdriver. Two were broken, and 1 was movable. RESULTS: Histologic analysis showed good osseointegration in all stable samples, and new bone formation and bone apposition to the surface of the threads in loaded and unloaded samples. Histomorphometric evaluation showed high bone-to-implant contact values in the loaded samples, but no significant statistical differences from the unloaded ones. CONCLUSIONS: Titanium alloy microimplants with small diameters (1.2-1.3mm) are strong enough for self-drilling and immediate loading in thin cortical bone areas, but, to reduce the chance of breakage, a drilling of a pilot hole is suggested in thick cortical bone areas.

Precise Morphology Control and Continuous Fabrication of Perovskite Solar Cells Using Droplet-Controllable Electrospray Coating System.

Herein, we developed a novel electrospray coating system for continuous fabrication of perovskite solar cells with high performance. Our system can systemically control the size of CH3NH3PbI3 precursor droplets by modulating the applied electrical potential, shown to be a crucial factor for the formation of perovskite films. As a result, we have obtained pinhole-free and large grain-sized perovskite solar cells, yielding the best PCE of 13.27% with little photocurrent hysteresis. Furthermore, the average PCE through the continuous coating process was 11.56 ± 0.52%. Our system demonstrates not only the high reproducibility but also a new way to commercialize high-quality perovskite solar cells.

Excellent optical and interfacial performance of a PEDOT-b-PEG block copolymer counter electrode for polymer electrolyte-based solid-state dye-sensitized solar cells.

A poly(3,4-ethylenedioxythiophene)-b-poly(ethylene glycol) (PEDOT-b-PEG) block copolymer doped with perchlorate on FTO shows excellent optical and interfacial performance as a counter electrode (CE), such as low charge transfer resistance and low reflectivity for polymer electrolyte-based solid-state dye-sensitized solar cells (DSCs), resulting in 8.45% energy conversion efficiency, greater than the common Pt CE, via a facile room-temperature process.

Toward Higher Energy Conversion Efficiency for Solid Polymer Electrolyte Dye-Sensitized Solar Cells: Ionic Conductivity and TiO2 Pore-Filling.

Even though the solid polymer electrolyte has many intrinsic advantages over the liquid electrolyte, its ionic conductivity and mesopore-filling are much poorer than those of the liquid electrolyte, limiting its practical application to electrochemical devices such as dye-sensitized solar cells (DSCs). Two major shortcomings associated with utilizing solid polymer electrolytes in DSCs are first discussed, low ionic conductivity and poor pore-filling in mesoporous photoanodes for DSCs. In addition, future directions for the successful utilization of solid polymer electrolytes toward improving the performance of DSCs are proposed. For instance, the facilitated mass-transport concept could be applied to increase the ionic conductivity. Modified biphasic and triple-phasic structures for the photoanode are suggested to take advantage of both the liquid- and solid-state properties of electrolytes.

Synergistic catalytic effect of a composite (CoS/PEDOT:PSS) counter electrode on triiodide reduction in dye-sensitized solar cells.

Inorganic/organic nanocomposite counter electrodes comprised of sheetlike CoS nanoparticles dispersed in polystyrenesulfonate-doped poly(3,4-ethylenedioxythiophene (CoS/PEDOT:PSS) offer a synergistic effect on catalytic performance toward the reduction of triiodide for dye-sensitized solar cells (DSSCs), yielding 5.4% power conversion efficiency, which is comparable to that of the conventional platinum counter electrode (6.1%). The electrochemical impedance spectroscopy (EIS) and cyclic voltammetry measurements revealed that the composite counter electrodes exhibited better catalytic activity, fostering rate of triiodide reduction, than that of pristine PEDOT: PSS electrode. The simple preparation of composite (CoS/PEDOT:PSS) electrode at low temperature with improved electrocatalytic properties are feasible to apply in flexible substrates, which is at most urgency for developing novel counter electrodes for lightweight flexible solar cells.