Long-Term Highly Stable High-Voltage LiCoO2 Synthesized via a Solid Sulfur-Assisted One-Pot Approach.

Commercialized lithium cobalt oxide (LCO) only shows a relatively low capacity of ≈175 mAh g-1 despite a high theoretical capacity of ≈274 mAh g-1 . As an effective and direct strategy, increasing its charge cutoff voltage can, in principle, escalate the capacity, which is however precluded by the irreversible phase transition, oxygen loss, and severe side reactions with electrolytes normally. Herein, an in situ sulfur-assisted solid-state approach is proposed for one-pot synthesis of long-term highly stable high-voltage LCO with a novel compound structure. The coating of coherent spinel Lix Co2 O4 shells on and the gradient doping of SO4 2- polyanions into LCO are in situ realized simultaneously in terms of gas-solid interface reactions between metal oxides and generated SO2 gas from sulfur during synthesis. At 4.6 V, this LCO shows the discharge capacities of 232.4 mAh g-1 at 0.1 C (1 C = 280 mA g-1 ), 215 mAh g-1 at 1 C and 139 mAh g-1 even at 20 C and the capacity retentions of 97.4% (89.7%) after 100 (300) cycles at 1 C. This approach is facile, low-cost and up-scalable and may provide a route to improve the performance of LCO and other electrode materials greatly.

Unveiling the Roles of Trace Fe and F Co-doped into High-Ni Li-Rich Layered Oxides in Performance Improvement.

High-Ni Li-rich layered oxides (HNLOs) derived from Li-rich Mn-based layered oxides (LRMLOs) can effectively mitigate the voltage decay of LRMLOs but normally suffered from decreased capacity and cycling stability. Herein, an effective, simple, and up-scalable co-doping strategy of trace Fe and F ions via a facile expanded graphite template-sacrificed approach was proposed for improving the performance of HNLOs. The trace Fe and F co-doping can far more effectively improve both its rate capability and cycling stability in a synergistic manner compared to the introduction of individual Fe cations and F anions. The co-doping of Fe and F increased the Li-O bonds by a magnitude far larger than the summation of the increments by their individual doping, quite favorable for the performance. The trace Fe doping can escalate the capacity and enhance the rate capability significantly by increasing the components of lower valence transition metals to activate their redox reactions more effectively and improving both the electronic and ionic conduction. In contrast, trace F can improve the cycling stability remarkably by lowering the O 2p band top to suppress the lattice oxygen escape effectively which were revealed by density functional theory calculations. The co-doped cathode exhibited excellent cycling stability with a superior capacity retention of 90% after 200 cycles at 1 C, much higher than 64% for the pristine sample. This study offers an idea for synergistically improving the performance of Li-rich layered oxides by co-doping trace Fe cations and F anions simultaneously, which play a complementary role in performance improvement.

Recent Advances in Polymers for Potassium Ion Batteries.

Potassium-ion batteries (KIBs) are considered to be an effective alternative to lithium-ion batteries (LIBs) due to their abundant resources, low cost, and similar electrochemical properties of K+ to Li+, and they have a good application prospect in the field of large-scale energy storage batteries. Polymer materials play a very important role in the battery field, such as polymer electrode materials, polymer binders, and polymer electrolytes. Here in this review, we focus on the research progress of polymers in KIBs and systematically summarize the research status and achievements of polymer electrode materials, electrolytes, and binders in potassium ion batteries in recent years. Finally, based on the latest representative research of polymers in KIBs, some suggestions and prospects are put forward, which provide possible directions for future research.

Annelid-inspired high-elongation origami robot using partial material removal.

Existing soft robots face challenges given the need for an improved flexible robot elongation rate, bending angle and movement flexibility in space target acquisition, disaster search and rescue, unknown environment detection and other fields. Yoshimura tubular origami shows good applied performance with regard to the axial elongation ratio. However, due to the characteristics of nonrigid folding and a negative Poisson's ratio, the axial elongation length and bending angle of the Yoshimura tubular origami mechanism are limited. Annelids show highly flexible body movement. By analyzing the main factors limiting the axial elongation rate of the Yoshimura tubular origami mechanism and imitating the morphological characteristics and motion mechanism of annelid somite joints, we proposed a method to achieve high flexibility and large angle bending of a tubular origami mechanism based on local material removal and macroscopic elimination of the negative Poisson's ratio. Combined with a Ni-Ti memory alloy wire segmented driving scheme based on force constraints and geometric constraints a continuous origami robot is designed. The optimal cutting amount of the origami mechanism is determined by experiments, and the maximum elongation ratio and bending angle of the origami mechanism reach 2.5 and 3 times those before material removal, respectively. The paper folding module unit was solved in a kinematic analysis workspace. Finally, a prototype was used to verify the performance and demonstrate the application potential of the robot in an unstructured rescue scene.

Lithium Antievaporation-Loss Engineering via Sodium/Potassium Doping Enables Superior Electrochemical Performance of High-Nickel Li-Rich Layered Oxide Cathodes.

Low-cost Mn- and Li-rich layered oxides suffer from rapid voltage decay, which can be improved by increasing the nickel content to derive high nickel Li-rich layered oxides (HNLO) but is normally accompanied by reduced capacity and inferior cycling stability. Herein, Na or K ions are successfully doped into the lattice of high nickel Li-rich Li1.2-xMxNi0.32Mn0.48O2 (M = Na, K) layered oxides via a facile expanded graphite template-sacrificed approach. Both Na- and K-doped samples exhibit excellent rate capability and cycling stability compared with the un-doped one. The Na-doped sample shows a capacity retention of 93% after 200 cycles at 1C, which is quite outstanding for HNLO. The greatly improved electrochemical performances are attributed to the increased effective Li content in the lattice via Li antievaporation-loss engineering, the expanded Li slab, the pillaring effect, the increased C2/m component, and the improved electronic conductivity. Different performances by the introduction of sodium and potassium ions may be ascribed to their different ionic radii, which give rise to their different doping behaviors and threshold doping amounts. This work provides a new idea of enhancing electrochemical performance of HNLO by doping proper alien elements to increase the lattice lithium content effectively.

Mapping the distributions of blood-sucking mites and mite-borne agents in China: a modeling study.

BACKGROUND: Emerging mite-borne pathogens and associated disease burdens in recent decades are raising serious public health concerns, yet their distributions and ecology remain under-investigated. We aim to describe the geographical distributions of blood-sucking mites and mite-borne agents and to assess their ecological niches in China. METHODS: We mapped 549 species of blood-sucking mites belonging to 100 genera at the county level and eight mite-associated agents detected from 36 species of blood-sucking mites in China during 1978-2020. Impacts of climatic and environmental factors on the ecology of 21 predominant vector mites and a leading pathogen, Orientia tsutsugamushi, were assessed using boosted regression tree (BRT) models, and model-predicted risks were mapped. We also estimated the model-predicted number, area and population size of affected counties for each of the 21 mite species in China. RESULTS: Laelaps echidninus is the leading mite species that potentially affects 744 million people, followed by La. jettmari (517 million) and Eulaelaps stabularis (452 million). Leptotrombidium scutellare is the mite species harboring the highest variety of mite-borne agents including four Rickettsia species and two viruses, followed by Eu. stabularis (2 agents), L. palpale (2) and La. echidninus (2). The top two agents that parasitize the largest number of mite species are O. tsutsugamushi (28 species) and hantavirus (8). Mammalian richness, annual mean temperature and precipitation of the driest quarter jointly determine the ecology of the mites, forming four clusters of major mite species with distinct geographic distributions. High-risk areas of O. tsutsugamushi are mainly distributed in southern and eastern coastal provinces where 71.5 million people live. CONCLUSIONS: Ecological niches of major mite species and mite-borne pathogens are much more extensive than what have been observed, necessitating expansion of current filed surveillance.

Mapping the Distributions of Mosquitoes and Mosquito-Borne Arboviruses in China.

The geographic expansion of mosquitos is associated with a rising frequency of outbreaks of mosquito-borne diseases (MBD) worldwide. We collected occurrence locations and times of mosquito species, mosquito-borne arboviruses, and MBDs in the mainland of China in 1954-2020. We mapped the spatial distributions of mosquitoes and arboviruses at the county level, and we used machine learning algorithms to assess contributions of ecoclimatic, socioenvironmental, and biological factors to the spatial distributions of 26 predominant mosquito species and two MBDs associated with high disease burden. Altogether, 339 mosquito species and 35 arboviruses were mapped at the county level. Culex tritaeniorhynchus is found to harbor the highest variety of arboviruses (19 species), followed by Anopheles sinensis (11) and Culex pipiens quinquefasciatus (9). Temperature seasonality, annual precipitation, and mammalian richness were the three most important contributors to the spatial distributions of most of the 26 predominant mosquito species. The model-predicted suitable habitats are 60-664% larger in size than what have been observed, indicating the possibility of severe under-detection. The spatial distribution of major mosquito species in China is likely to be under-estimated by current field observations. More active surveillance is needed to investigate the mosquito species in specific areas where investigation is missing but model-predicted probability is high.

Mapping ticks and tick-borne pathogens in China.

Understanding ecological niches of major tick species and prevalent tick-borne pathogens is crucial for efficient surveillance and control of tick-borne diseases. Here we provide an up-to-date review on the spatial distributions of ticks and tick-borne pathogens in China. We map at the county level 124 tick species, 103 tick-borne agents, and human cases infected with 29 species (subspecies) of tick-borne pathogens that were reported in China during 1950-2018. Haemaphysalis longicornis is found to harbor the highest variety of tick-borne agents, followed by Ixodes persulcatus, Dermacentor nutalli and Rhipicephalus microplus. Using a machine learning algorithm, we assess ecoclimatic and socioenvironmental drivers for the distributions of 19 predominant vector ticks and two tick-borne pathogens associated with the highest disease burden. The model-predicted suitable habitats for the 19 tick species are 14‒476% larger in size than the geographic areas where these species were detected, indicating severe under-detection. Tick species harboring pathogens of imminent threats to public health should be prioritized for more active field surveillance.

A dataset of distribution and diversity of blood-sucking mites in China.

Mite-borne diseases, such as scrub typhus and hemorrhagic fever with renal syndrome, present an increasing global public health concern. Most of the mite-borne diseases are caused by the blood-sucking mites. To present a comprehensive understanding of the distributions and diversity of blood-sucking mites in China, we derived information from peer-reviewed journal articles, thesis publications and books related to mites in both Chinese and English between 1978 and 2020. Geographic information of blood-sucking mites' occurrence and mite species were extracted and georeferenced at the county level. Standard operating procedures were applied to remove duplicates and ensure accuracy of the data. This dataset contains 6,443 records of mite species occurrences at the county level in China. This geographical dataset provides an overview of the species diversity and wide distributions of blood-sucking mites, and can potentially be used in distribution prediction of mite species and risk assessment of mite-borne diseases in China.

Epidemiology of and Risk Factors for COVID-19 Infection among Health Care Workers: A Multi-Centre Comparative Study.

Healthcare workers (HCWs) worldwide are putting themselves at high risks of coronavirus disease 2019 (COVID-19) by treating a large number of patients while lacking protective equipment. We aim to provide a scientific basis for preventing and controlling the COVID-19 infection among HCWs. We used data on COVID-19 cases in the city of Wuhan to compare epidemiological characteristics between HCWs and non-HCWs and explored the risk factors for infection and deterioration among HCWs based on hospital settings. The attack rate (AR) of HCWs in the hospital can reach up to 11.9% in Wuhan. The time interval from symptom onset to diagnosis in HCWs and non-HCWs dropped rapidly over time. From mid-January, the median time interval of HCW cases was significantly shorter than in non-HCW cases. Cases of HCWs and non-HCWs both clustered in northwestern urban districts rather than in rural districts. HCWs working in county-level hospitals in high-risk areas were more vulnerable to COVID-19. HCW cases working in general, ophthalmology, and respiratory departments were prone to deteriorate compared with cases working in the infection department. The AR of COVID-19 in HCWs are higher than in non-HCWs. Multiple factors in hospital settings may play important roles in the transmission of COVID-19. Effective measures should be enhanced to prevent HCWs from COVID-19 infection.

Travel-related infections in mainland China, 2014-16: an active surveillance study.

BACKGROUND: Transmission of infection through international travel is a growing health issue, and the frequency of imported infection is increasing in China. We aimed to quantify the total number of infections imported into mainland China by arriving travellers. METHODS: We actively surveyed arriving travellers at all 272 international entry-exit ports in mainland China. Suspected cases were detected through fever screening, medical inspection, self-declaration, and reporting by on-board staff. Participants completed a standardised questionnaire with questions about demographics, their travel itinerary (including detailed information about all countries or regions visited), and clinical manifestations. Nasopharyngeal swabs, sputum samples, faecal samples, vomitus, blood, and serum were collected as appropriate for diagnoses. Diagnosis was made by specific laboratory tests according to the national technical guidelines. Infections were classified as respiratory, gastrointestinal, vector-borne, blood-transmitted and sex-transmitted, or mucocutaneous. We divided arriving travellers into two groups: travellers coming from countries other than China, and travellers coming from Hong Kong, Macau, and Taiwan. We integrated surveillance data for 2014-16, calculated incidences of travel-related infections, and compared the frequency of infections among subgroups. FINDINGS: Between Jan 1, 2014, and Dec 31, 2016, 22 797 cases were identified among 805 993 392 arriving travellers-an overall incidence of 28·3 per million. 45 pathogens were detected in participants: 18 respiratory (19 662 cases), ten gastrointestinal (189 cases), seven vector-borne (831 cases), seven blood-transmitted and sex-transmitted (1531 cases), and three mucocutaneous (584 cases). Both the overall number and incidence of infection were more than five times higher in 2016 than in 2014. Case numbers and incidences also varied substantially by province, autonomous region, and municipality. Overall, 17 643 (77%) infections were detected by fever screening, but 753 (49%) blood-transmitted and sex-transmitted infections were identified through medical inspection. 14 305 (73%) cases of respiratory infection and 96 (51%) of gastrointestinal infections were in tourists. Tuberculosis, hepatitis A virus, vector-borne, and blood-transmitted and sex-transmitted infections were common among Chinese labourers who worked abroad. Dengue and malaria were most commonly diagnosed in travellers arriving from Africa. 12 126 (93%) of the 12 985 cases arriving from Hong Kong, Macau, or Taiwan were respiratory infections. Hand, foot, and mouth disease accounted for 2·90% of infections in travellers from Hong Kong, Macau, or Taiwan and 0·31% of infections in international travellers. INTERPRETATION: This report is the first to characterise the profile of travel-related infections among arriving travellers in mainland China. Our findings should increase public awareness of the potential risk of imported infections, and help health-care providers to make evidence-based health recommendations to travellers. FUNDING: The Natural Science Foundation of China.