Electron tomography reveals details of the internal microstructure of desalination membranes.

As water availability becomes a growing challenge in various regions throughout the world, desalination and wastewater reclamation through technologies such as reverse osmosis (RO) are becoming more important. Nevertheless, many open questions remain regarding the internal structure of thin-film composite RO membranes. In this work, fully aromatic polyamide films that serve as the active layer of state-of-the-art water filtration membranes were investigated using high-angle annular dark-field scanning transmission electron microscopy tomography. Reconstructions of the 3D morphology reveal intricate aspects of the complex microstructure not visible from 2D projections. We find that internal voids of the active layer of compressed commercial membranes account for less than 0.2% of the total polymer volume, contrary to previously reported values that are two orders of magnitude higher. Measurements of the local variation in polyamide density from electron tomography reveal that the polymer density is highest at the permeable surface for the two membranes tested and establish the significance of surface area on RO membrane transport properties. The same type of analyses could provide explanations for different flux variations with surface area for other types of membranes where the density is distributed differently. Thus, 3D reconstructions and quantitative analyses will be crucial to characterize the complex morphology of polymeric membranes used in next-generation water-purification membranes.

Living biofouling-resistant membranes as a model for the beneficial use of engineered biofilms.

Membrane systems are used increasingly for water treatment, recycling water from wastewater, during food processing, and energy production. They thus are a key technology to ensure water, energy, and food sustainability. However, biofouling, the build-up of microbes and their polymeric matrix, clogs these systems and reduces their efficiency. Realizing that a microbial film is inevitable, we engineered a beneficial biofilm that prevents membrane biofouling, limiting its own thickness by sensing the number of its cells that are present via a quorum-sensing circuit. The beneficial biofilm also prevents biofilm formation by deleterious bacteria by secreting nitric oxide, a general biofilm dispersal agent, as demonstrated by both short-term dead-end filtration and long-term cross-flow filtration tests. In addition, the beneficial biofilm was engineered to produce an epoxide hydrolase so that it efficiently removes the environmental pollutant epichlorohydrin. Thus, we have created a living biofouling-resistant membrane system that simultaneously reduces biofouling and provides a platform for biodegradation of persistent organic pollutants.

Three-Dimensional Morphology of Polymeric Membranes from Electron Tomography.

Recent advances in the water-energy landscape hinge upon our improved understanding of the complex morphology of materials involved in water treatment and energy production. Due to their versatility and tunability for applications ranging from drug delivery to fuel cells, polymeric systems will play a crucial role in shaping the future of water-energy nexus applications. Electron tomography (ET) stands as a transformative approach for elucidating the intricate structures inherent to polymers, offering unparalleled insights into their nanoscale architectures and functional properties in three dimensions. In particular, the various morphological and chemical characteristics of polymer membranes provide opportunities for perturbations to standard ET for the study of these systems. We discuss the applications of transmission electron microscopy in establishing structure-function relationships in polymeric membranes with an emphasis on traditional ET and cryogenic ET (cryo-ET). The synergy between ET and cryo-ET to unravel structural complexities and dynamic behaviors of polymer membranes holds immense potential in driving progress and innovation across frontiers related to water-energy nexus applications. Expected final online publication date for the Annual Review of Chemical and Biomolecular Engineering , Volume 15 is June 2024. Please see http://www.annualreviews.org/page/journal/pubdates for revised estimates.

New erythrocyte parameters derived from the Coulter principle relate with red blood cell properties-A pilot study in diabetes mellitus.

In routine hematological instruments, blood cells are counted and sized by monitoring the impedance signals induced during their passage through a Coulter orifice. However, only signals associated with centered paths in the aperture are considered for analysis, while the rejected measurements, caused by near-wall trajectories, can provide additional information on red blood cells (RBC), as recent publications suggest. To assess usefulness of two new parameters in describing alterations in RBC properties, we performed a pilot study to compare blood samples from patients with diabetes mellitus (DM), frequent pathological condition associated with impairment in RBC deformability, versus controls. A total of 345 blood samples were analyzed: 225 in the DM group and 120 in the control group. A diagram of [Formula: see text] and [Formula: see text], the two new parameters derived from the analysis of impedancemetry pulses, was used to compare distribution of RBC subpopulations between groups. To discriminate RBC from DM and control individuals, based on our multiparametric analysis, we built a score from variables derived from [Formula: see text] matrix which showed good performances: area under the receiving operating characteristic curve 0.948 (0.920-0.970), p<0.0001; best discriminating value: negative predictive value 94.7%, positive predictive value was 78.4%. These results seem promising to approach RBC alterations in routine laboratory practice. The related potential clinically relevant outcomes remain to be investigated.

Nanoscale control of internal inhomogeneity enhances water transport in desalination membranes.

Biological membranes can achieve remarkably high permeabilities, while maintaining ideal selectivities, by relying on well-defined internal nanoscale structures in the form of membrane proteins. Here, we apply such design strategies to desalination membranes. A series of polyamide desalination membranes-which were synthesized in an industrial-scale manufacturing line and varied in processing conditions but retained similar chemical compositions-show increasing water permeability and active layer thickness with constant sodium chloride selectivity. Transmission electron microscopy measurements enabled us to determine nanoscale three-dimensional polyamide density maps and predict water permeability with zero adjustable parameters. Density fluctuations are detrimental to water transport, which makes systematic control over nanoscale polyamide inhomogeneity a key route to maximizing water permeability without sacrificing salt selectivity in desalination membranes.