The performance of chlorobenzene degradation in groundwater: comparison of hydrogen peroxide, nanoscale calcium peroxide and sodium percarbonate activated with ferrous iron.

The chlorobenzene (CB) degradation performances by various oxidants, including hydrogen peroxide (H2O2), nanoscale calcium peroxide (nCaO2) and sodium percarbonate (SPC), activated with ferrous iron (Fe(II)) were investigated and thoroughly compared. The results showed that all tested systems had strong abilities to degrade CB. The CB removal rate increased with increasing dosages of oxidants or Fe(II) because the generation of reactive oxygen species could be promoted with the chemical dosages' increase. Response surface and contour plots showed that CB could achieve a better removal performance at the same H2O2 and Fe(II) molar content, but the Fe(II) dosage was higher than that of oxidants in the nCaO2 and SPC systems. The optimal molar ratios of H2O2/Fe(II)/CB, nCaO2/Fe(II)/CB and SPC /Fe(II)/CB were 5.2/7.6/1, 8/8/1, and 4.5/8/1, respectively, in which 98.1%, 98%, and 96.4% CB removals could be obtained in 30 min reaction. The optimal pH condition was around 3, while CB removal rates were less than 20% in all three systems when the initial pH was adjusted to 9. The oxidative hydroxyl radicals (HO•) and singlet oxygen (1O2) had been detected by the electron paramagnetic resonance test. Based upon the results of liquid chromatograph-mass spectrometer analysis, the pathways of CB degradation were proposed, in which 1O2 roles were elaborated innovatively in the CB degradation mechanism. The CB degradation performance was significantly affected in actual groundwater, while increasing the molar ratio of oxidant/Fe(II)/CB was an effective way to overcome the adverse effects caused by the complex of actual groundwater matrix.

Co-expression of Pseudomonas alcaligenes lipase and its specific foldase in Pichia pastoris by a dual expression cassette strategy.

Lipomax is a commercialized foldase-dependent Pseudomonas lipase that was previously expressed only in Pseudomonas strains. Here, using Pichia pastoris as the host, we report a new co-expression method that leads to the successful production of Lipomax. The active Lipomax is extracellularly co-expressed with its cognate foldase (LIM); and the purified enzyme mix has the optimum pH at pH 8.0 and an optimal temperature around 40 °C. N-glycosylation was observed for Pichia produced Lipomax, and its reduction was shown to increase the lipolytic activity. With different p-nitrophenyl esters as the substrates, the substrate profiling analyses further indicate that Lipomax prefers esters with middle-long chain fatty acids, showing the highest specific activity to p-nitrophenyl caprylate (C8). The extracellular co-expression of Lipomax and LIM in Pichia will not only increase our ability to investigate additional eukaryotic hosts for lipase expression, but also be of considerable value in analyzing other foldase-dependent lipases.

All-Carbon Pressure Sensors with High Performance and Excellent Chemical Resistance.

An all-carbon pressure sensor is designed and fabricated based on reduced graphene oxide (rGO) nanomaterials. By sandwiching one layer of superelastic rGO aerogel between two freestanding high-conductive rGO thin papers, the sensor works based on the contact resistance at the aerogel-paper interfaces, getting rid of the alien materials such as polymers and metals adopted in traditional sensors. Without the limitation of alien materials, the all-carbon sensors demonstrate an ultrawide detecting range (0.72 Pa-130 kPa), low energy consumption (≈0.58 µW), ultrahigh sensitivity (349-253 kPa-1 ) at low-pressure regime (<1.4 Pa), fast response time (8 ms at 1 kPa), high stability (10 000 unloading-loading cycles between 0 and 1 kPa), light weight (<10 mg), easily scalable fabrication process, and excellent chemical stability. These merits enable them to detect real-time human physiological signals and monitor the weights of various droplets of not only water but also hazardous chemical reagents including strong acid, strong alkali, and organic solvents. This shows their great potential applications in real-time health monitoring, sport performance detecting, harsh environment-related robotics and industry, and so forth.

Electrochemical Enantioselective Recognition in a Highly Ordered Self-Assembly Framework.

Construction of convenient systems for isomer discrimination is of great importance for medical and life sciences. Here, we report a simple and effective chiral sensing device based on a highly ordered self-assembly framework. Cu2+-modified ß-cyclodextrin (Cu-ß-CD) was self-assembled to the ammonia-ethanol cotreated chitosan (ae-CS), and the highly ordered framework was gradually formed during the "re-growth" process of the shrinked ae-CS films. Tryptophan (Trp) isomers were well discriminated with the highly ordered framework by electrochemical approach. This study is the first example showing how an ordered structure influences chiral recognition.

Application of ascorbic acid to enhance trichloroethene degradation by Fe(III)-activated calcium peroxide.

The enhancement effect of an environmentally friendly reducing agent, ascorbic acid (AA), on trichloroethene (TCE) degradation by Fe(III)-activated calcium peroxide (CP) was evaluated. The addition of AA accelerated the transformation of Fe(III) to Fe(II), and the complexation of Fe(III)/Fe(II) with AA and its products alleviated the precipitation of dissolved iron. These impacts enhanced the generation of reactive oxygen species (ROSs). Investigation of ROSs using chemical probe tests, electron paramagnetic resonance (EPR) tests, and radical scavenger tests strongly confirm large production of hydroxyl radicals (HO•) that is responsible for TCE degradation. The generation of Cl- from the degraded TCE was complete in the enhanced CP/Fe(III)/AA system. The investigation of solution matrix effects showed that the TCE degradation rate decreases with the increase in solution pH, while Cl-, SO42- and NO3- anions have minor impact. Conversely, HCO3- significantly inhibited TCE degradation due to pH elevation and HO• scavenging. The results of experiments performed using actual groundwater indicated that an increase in reagent doses are required for effective TCE removal. In summary, the potential effectiveness of the CP/Fe(III)/AA oxidation system for remediation of TCE contaminated groundwater has been demonstrated. Additional research is needed to develop the system for practical implementation.

Benzene oxidation by Fe(III)-catalyzed sodium percarbonate: matrix constituent effects and degradation pathways.

Complete degradation of benzene by the Fe(III)-activated sodium percarbonate (SPC) system is demonstrated. Removal of benzene at 1.0 mM was seen within 160 min, depending on the molar ratios of SPC to Fe(III). A mechanism of benzene degradation was elaborated by free-radical probe-compound tests, free-radical scavengers tests, electron paramagnetic resonance (EPR) analysis, and determination of Fe(II) and H2O2 concentrations. The degradation products were also identified using gas chromatography-mass spectrometry method. The hydroxyl radical (HO.) was the leading species in charge of benzene degradation. The formation of HO. was strongly dependent on the generation of the organic compound radical (R.) and superoxide anion radical (O.). Benzene degradation products included hydroxylated derivatives of benzene (phenol, hydroquinone, benzoquinone, and catechol) and aliphatic acids (oxalic and fumaric acids). The proposed degradation pathways are consistent with radical formation and identified products. The investigation of selected matrix constituents showed that the Cl and HCO3 had inhibitory effects on benzene degradation. Natural organic matter (NOM) had accelerating influence in degrading benzene. The developed system was tested with groundwater samples and it was found that the Fe(III)-activated SPC has a great potential in effective remediation of benzene-contaminated groundwater while more further studies should be done for its practical application in the future because of the complex subsurface environment.

Ultrahigh-Power-Factor Carbon Nanotubes and an Ingenious Strategy for Thermoelectric Performance Evaluation.

An ingenious strategy is put forward to evaluate accurately the thermoelectric performance of carbon nanotube (CNT) thin films, including thermal conductivity, electrical conductivity, and Seebeck coefficient in the same direction. The results reveal that the as-prepared CNT interconnected films and CNT fibers possess enormous potential of thermoelectric applications because of their ultrahigh power factors.

The destruction of benzene by calcium peroxide activated with Fe(II) in water.

The ability of Fe(II)-activated calcium peroxide (CaO2) to remove benzene is examined with a series of batch experiments. The results showed that benzene concentrations were reduced by 20 to 100% within 30 min. The magnitude of removal was dependent on the CaO2/Fe(II)/Benzene molar ratio, with much greater destruction observed for ratios of 4/4/1 or greater. An empirical equation was developed to quantify the destruction rate dependence on reagent composition. The presence of oxidative hydroxyl radicals (HO•) and reductive radicals (primarily O2•-) was identified by probe compound testing and electron paramagnetic resonance (EPR) tests. The results of the EPR tests indicated that the application of CaO2/Fe(II) enabled the radical intensity to remain steady for a relatively long time. The effect of initial solution pH was also investigated, and CaO2/Fe(II) enabled benzene removal over a wide pH range of 3.0~9.0. The results of radical scavenging tests showed that benzene removal occurred primarily by HO• oxidation in the CaO2/Fe(II) system, although reductive radicals also contributed. The intermediates in benzene destruction were identified to be phenol and biphenyl. The results indicate that Fe(II)-activated CaO2 is a feasible approach for treatment of benzene in contaminated groundwater remediation.

DNA-inspired electrochemical recognition of tryptophan isomers by electrodeposited chitosan and sulfonated chitosan.

Inspired by the double helix structure of DNA, a simple enantioselective system based on chitosan (CS) was employed for electrochemical enantiorecognition of tryptophan (Trp) isomers. The recognition mechanism was proposed from the supramolecular point of view, which was further verified by the recognition of Trp isomers with sulfonated CS (SCS). The SCS-based chiral system presented the ability of indicating the percentage of d-Trp in racemic mixture, extending future applications of the electrochemical chiral system based on natural polysaccharides.

Enhancement effects of chelating agents on the degradation of tetrachloroethene in Fe(III) catalyzed percarbonate system.

The performance of Fe(III)-based catalyzed sodium percarbonate (SPC) for stimulating the oxidation of tetrachloroethene (PCE) for groundwater remediation applications was investigated. The chelating agents citric acid monohydrate (CIT), oxalic acid (OA), and Glutamic acid (Glu) significantly enhanced the degradation of PCE. Conversely, ethylenediaminetetraacetic acid (EDTA) had a negative impact on PCE degradation, which may due to its strong Fe chelation and HO• scavenging abilities. However, excessive SPC or chelating agent will retard PCE degradation. In addition, investigations using free radical probe compounds and radical scavengers revealed that PCE was primarily degraded by HO• radical oxidation in both the chelated and non-chelated systems, while O2•- also participated in the non-chelated system and the OA and Glu modified systems. According to the electron paramagnetic resonance (EPR) studies, the presence of HO• in the Fe(III)/SPC system was maintained much longer than that in the Fe(II)/SPC system. The results indicated that the addition of CIT, OA or Glu indeed enhanced the generation of HO• in the first 10 min and promoted degradation efficiency by increasing the amount of Fe(III) and maintaining the concentration of HO• radicals in solution. In conclusion, chelated Fe(III)-based catalyzed SPC oxidation is a promising method for the remediation of PCE-contaminated groundwater.

Trichloroethylene degradation by persulphate with magnetite as a heterogeneous activator in aqueous solution.

Iron oxide-magnetite (Fe3O4) as a heterogeneous activator to activate persulphate anions (S2O8(2-)) for trichloroethylene (TCE) degradation was investigated in this study. The experimental results showed that TCE could be completely oxidized within 5 h by using 5 g L(-1) magnetite and 63 mM S2O8(2-), indicating the effectiveness of the process for TCE removal. Various factors of the process, including. (S2O8(2-) and magnetite dosages, and initial solution pH, were evaluated, and TCE degradation fitted well to the pseudo-first-order kinetic model. The calculated kinetic rate constant was increased with increasing S2O8(2-) and magnetite dosages, but it was independent of solution pH. In addition, the changes of magnetite morphology examined by scanning electron microscopy and X-ray powder diffraction, respectively, confirmed the slight corrosion with α-Fe2O3 coated on the magnetite surface. The probe compounds tests clearly identified the generation of the reactive oxygen species in the system. While the free radical quenching studies further demonstrated that •SO4- and •OH were the major radicals responsible for TCE degradation, whereas •O2- contributed less in the system, and therefore the roles of reactive oxygen species on TCE degradation mechanisms were proposed accordingly. To our best knowledge, this is the first time the performance and mechanism of magnetite-activated persulphate oxidation for TCE degradation are reported. The findings of this study provided a new insight into the heterogeneous catalysis mechanism and showed a great potential for the practical application of this technique in in situ TCE-contaminated groundwater remediation.

Trichloroethylene oxidation performance in sodium percarbonate (SPC)/Fe2+ system.

In this study, in-situ chemical oxidation technique employing Fe(II) catalytic sodium percarbonate (SPC) to stimulate the oxidation of trichloroethylene (TCE) in contaminated groundwater remediation was investigated. The effects of various factors including the SPC/TCE/Fe2+ molar ratio, the initial solution pH and the widely found constituents in groundwater matrix such as Cl(-), HCO3(-), SO4(2-) and NO3(-) anions and natural organic matters were evaluated. The experimental results showed that TCE could be completely oxidized in 5 min at 20 degrees C with a SPC/TCE/Fe2+ molar ratio of 5:1:10, indicating the significant effectiveness of the SPC/Fe2+ system for TCE removal. The initial solution pH value (from 3 to 11) has less influence on TCE oxidation rate. In contrast, Cl(-) and HCO3(-) anions had a negative effect on TCE removal in which HCO3(-) possesses a stronger influence than Cl(-), whereas the effects of both SO4(2-) and NO3(-) anions appeared to be negligible. With the 1.0-10 mg/L concentrations of humic acid in solution, slightly inhibitive effect was observed, suggesting that dissolved organic matters consumed less SPC and had a negligible effect on the oxidation of TCE in SPC/Fe2+ system. From the intermediate products' analyses and the released Cl(-) contents from TCE parent contaminant in solution, all the decomposed TCE had completely dechlorinated and led to carbon dioxide and hydrocarbon. In conclusion, Fe(II) catalytic SPC oxidation is a highly promising technique for TCE-contaminated groundwater remediation, but some complex constituents such as HCO3(-), in in-situ groundwater matrix should be carefully considered for its practical application.

Efficient dechlorination of chlorinated solvent pollutants under UV irradiation by using the synthesized TiO2 nano-sheets in aqueous phase.

Titanium dioxide (TiO2), which is the widely used photo-catalyst, has been synthesized by simple hydrothermal solution containing tetrabutyl titanate and hydrofluoric acid. The synthesized product has been applied to photo-degradation in aqueous phase of chlorinated solvents, namely tetrachloroethene (PCE), trichloroethene (TCE) and 1,1,1-trichloroethane (TCA). The photo-degradation results revealed that the degradation of these harmful chemicals was better in UV/synthesized TiO2 system compared to UV/commercial P25 system and UV only system. The photo-catalytic efficiency of the synthesized TiO2 was 1.4, 1.8 and 3.0 folds higher compared to the commercial P25 for TCA, TCE and PCE degradation, respectively. Moreover, using nitrobenzene (NB) as a probe of hydroxyl radical (·OH), the degradation rate was better over UV/synthesized TiO2, suggesting the high concentration of ·OH generated in UV/synthesized TiO2 system. In addition, ·OH concentration was confirmed by the strong peak displayed in EPR analysis over UV/synthesized TiO2 system. The characterization result using XRD and TEM showed that the synthesized TiO2 was in anatase form and consisted of well-defined sheet-shaped structures having a rectangular outline with a thickness of 4 nm, side length of 50 nm and width of 33 nm and a surface 90.3 m(2)/g. XPS analysis revealed that ≡Ti-F bond was formed on the surface of the synthesized TiO2. The above results on both photocatalytic activity and the surface analysis demonstrated the good applicability of the synthesized TiO2 nano-sheets for the remediation of chlorinated solvent contaminated groundwater.

Biosynthesis of a new UDP-sugar, UDP-2-acetamido-2-deoxyxylose, in the human pathogen Bacillus cereus subspecies cytotoxis NVH 391-98.

We have identified an operon and characterized the functions of two genes from the severe food-poisoning bacterium, Bacillus cereus subsp. cytotoxis NVH 391-98, that are involved in the synthesis of a unique UDP-sugar, UDP-2-acetamido-2-deoxyxylose (UDP-N-acetyl-xylosamine, UDP-XylNAc). UGlcNAcDH encodes a UDP-N-acetyl-glucosamine 6-dehydrogenase, converting UDP-N-acetylglucosamine (UDP-GlcNAc) to UDP-N-acetyl-glucosaminuronic acid (UDP-GlcNAcA). The second gene in the operon, UXNAcS, encodes a distinct decarboxylase not previously described in the literature, which catalyzes the formation of UDP-XylNAc from UDP-GlcNAcA in the presence of exogenous NAD(+). UXNAcS is specific and cannot utilize UDP-glucuronic acid and UDP-galacturonic acid as substrates. UXNAcS is active as a dimer with catalytic efficiency of 7 mM(-1) s(-1). The activity of UXNAcS is completely abolished by NADH but unaffected by UDP-xylose. A real-time NMR-based assay showed unambiguously the dual enzymatic conversions of UDP-GlcNAc to UDP-GlcNAcA and subsequently to UDP-XylNAc. From the analyses of all publicly available sequenced genomes, it appears that UXNAcS is restricted to pathogenic Bacillus species, including Bacillus anthracis and Bacillus thuringiensis. The identification of UXNAcS provides insight into the formation of UDP-XylNAc. Understanding the metabolic pathways involved in the utilization of this amino-sugar may allow the development of drugs to combat and eradicate the disease.

Identification of a bifunctional UDP-4-keto-pentose/UDP-xylose synthase in the plant pathogenic bacterium Ralstonia solanacearum strain GMI1000, a distinct member of the 4,6-dehydratase and decarboxylase family.

The UDP-sugar interconverting enzymes involved in UDP-GlcA metabolism are well described in eukaryotes but less is known in prokaryotes. Here we identify and characterize a gene (RsU4kpxs) from Ralstonia solanacearum str. GMI1000, which encodes a dual function enzyme not previously described. One activity is to decarboxylate UDP-glucuronic acid to UDP-beta-l-threo-pentopyranosyl-4''-ulose in the presence of NAD(+). The second activity converts UDP-beta-l-threo-pentopyranosyl-4''-ulose and NADH to UDP-xylose and NAD(+), albeit at a lower rate. Our data also suggest that following decarboxylation, there is stereospecific protonation at the C5 pro-R position. The identification of the R. solanacearum enzyme enables us to propose that the ancestral enzyme of UDP-xylose synthase and UDP-apiose/UDP-xylose synthase was diverged to two distinct enzymatic activities in early bacteria. This separation gave rise to the current UDP-xylose synthase in animal, fungus, and plant as well as to the plant Uaxs and bacterial ArnA and U4kpxs homologs.

Biosynthesis of UDP-xylose and UDP-arabinose in Sinorhizobium meliloti 1021: first characterization of a bacterial UDP-xylose synthase, and UDP-xylose 4-epimerase.

Sinorhizobium meliloti is a soil bacterium that fixes nitrogen after being established inside nodules that can form on the roots of several legumes, including Medicago truncatula. A mutation in an S. meliloti gene (lpsB) required for lipopolysaccharide synthesis has been reported to result in defective nodulation and an increase in the synthesis of a xylose-containing glycan. Glycans containing xylose as well as arabinose are also formed by other rhizobial species, but little is known about their structures and the biosynthetic pathways leading to their formation. To gain insight into the biosynthesis of these glycans and their biological roles, we report the identification of an operon in S. meliloti 1021 that contains two genes encoding activities not previously described in bacteria. One gene encodes a UDP-xylose synthase (Uxs) that converts UDP-glucuronic acid to UDP-xylose, and the second encodes a UDP-xylose 4-epimerase (Uxe) that interconverts UDP-xylose and UDP-arabinose. Similar genes were also identified in other rhizobial species, including Rhizobium leguminosarum, suggesting that they have important roles in the life cycle of this agronomically important class of bacteria. Functional studies established that recombinant SmUxs1 is likely to be active as a dimer and is inhibited by NADH and UDP-arabinose. SmUxe is inhibited by UDP-galactose, even though this nucleotide sugar is not a substrate for the 4-epimerase. Unambiguous evidence for the conversions of UDP-glucuronic acid to UDP-α-D-xylose and then to UDP-ß-L-arabinose (UDP-arabinopyranose) was obtained using real-time (1)H-NMR spectroscopy. Our results provide new information about the ability of rhizobia to form UDP-xylose and UDP-arabinose, which are then used for the synthesis of xylose- and arabinose-containing glycans.

Trichloroethylene degradation by PVA-coated calcium peroxide nanoparticles in Fe(II)-based catalytic systems: enhanced performance by citric acid and nanoscale iron sulfide.

In this study, the enhanced trichloroethylene (TCE) degradation performance was investigated by polyvinyl alcohol coated calcium peroxide nanoparticles (PVA@nCP) as an oxidant in Fe(II)-based catalytic systems. The nanoscale iron sulfide (nFeS), having an average particle size of 115.4 nm, was synthesized in the laboratory and characterized by SEM, TEM, HR-TEM along with EDS elemental mapping, XRD, FTIR, ICP-OES, and XPS techniques. In only ferrous iron catalyzed system (PVA@nCP/Fe(II)), TCE degradation was recorded at 58.9% in 6 h. In comparison, this value was increased to 97.5% or 99.7% with the addition of citric acid (CA) or nFeS in PVA@nCP/Fe(II) system, respectively. A comparative study was performed with optimum usages of chemical reagents in both PVA@nCP/Fe(II)/CA and PVA@nCP/Fe(II)/nFeS systems. Further, the probe compounds tests and electron paramagnetic resonance (EPR) analysis confirmed the generation of reactive oxygen species. The scavenging experiments elucidated the dominant role of HO• to TCE degradation, particularly in PVA@nCP/Fe(II)/nFeS system. Both CA and nFeS strengthened PVA@nCP/Fe(II) system, but displayed completely different mechanisms in the enhancement of active radicals generation; hence, their different contribution to TCE degradation. The acidic environment was favorable for TCE degradation, and a high concentration of HCO3- inhibited TCE removal in both systems. Conclusively, compared to PVA@nCP/Fe(II)/nFeS system, PVA@nCP/Fe(II)/CA system resulted in encouraging TCE degradation outcomes in actual groundwater, showing great potential for prolonged benefits in the remediation of TCE polluted groundwater. Graphical abstract.

Degradation of trichloroethene by citric acid chelated Fe(II) catalyzing sodium percarbonate in the environment of sodium dodecyl sulfate aqueous solution.

In this study, the common chlorinated solvent trichloroethene (TCE) was selected as the target contaminant. The aqueous solution after solubilization treatment (containing TCE and sodium dodecyl sulfate (SDS)) was used as the research object to carry out the remediation technology research of citric acid (CA) enhanced Fe(II) activation in sodium percarbonate (SPC) system. In 0.15 mM TCE and 1 critical micelle concentration (CMC) SDS solution, CA chelating Fe(II) activated SPC could effectively promote 93.2% degradation of TCE when the dosages of SPC, Fe(II) and CA were 3.0, 6.0 and 3.0 mM, respectively. SDS had a significant inhibitory effect on the degradation of TCE, and the surface tension changed after the reaction. The addition of CA greatly increased the generation of hydroxyl radicals (HO) in the system, while the removal of TCE was mainly attributed to HO, and the removed TCE was almost completely dechlorinated. The pH range from 3 to 7 could keep the TCE degradation above 80.0%. In the actual groundwater remediation, this technique could also efficiently degrade TCE (including SDS), showing a great application potential and development prospective in practice.

Insights into enhanced removal of 1,2-dichloroethane by amorphous boron-enhanced Fenton system: Performances and mechanisms.

In this study, amorphous boron was employed as a reductant in traditional Fenton system for the first time to accelerate the regeneration of Fe(II). The degradation of 1,2-dichloroethane (DCA) was only 40.0% in Fenton system, while in the presence of amorphous boron, it could reach to 93.0% in 60 min. HO• was demonstrated to be the major reactive oxygen species (ROSs) and responsible for DCA degradation. Further, the mechanism of amorphous boron-enhanced Fenton system was described as follows. With the addition of amorphous boron, the reduction process occurred on its surface and Fe(III) was regenerated to Fe(II) to further utilize H2O2 and produce more HO• for DCA removal. Meanwhile, amorphous boron was oxidized to B2O3 and a portion of H3BO3 leaching into the solution occurred. Both B2O3 and H3BO3 had no reactivity for Fe(III) reduction. Moreover, DCA could be entirely dechlorinated and mineralized to CO2, Cl- and H2O. Vinyl chloride (VC) and dichloromethane (DCM) were the mainly intermediates in DCA degradation and two possible pathways were inferred. Eventually, the performance of DCA degradation in complex solution matrixes and for other contaminants removal were tested, demonstrating the broad-spectrum reactivity and superiority of amorphous boron-enhanced Fenton system in the remediation of contaminated groundwater.

Mechanism of surfactant in trichloroethene degradation in aqueous solution by sodium persulfate activated with chelated-Fe(II).

The mechanism of surfactants in surfactant-in situ chemical oxidation (S-ISCO) coupled process for trichloroethene (TCE) degradation was firstly reported. The performance of TCE solubilization and inhibition of TCE degradation in three nonionic surfactants (TW-80, Brij-35, TX-100) in PS/Fe(II)/citric acid (CA) system was compared and TW-80 was evaluated to be the optimal surfactant in S-ISCO coupled process due to the best TCE solubilizing ability and minimal inhibition for TCE degradation (only 31.8% TCE inhibition in the presence of 1 g L-1 TW-80 surfactant). The inhibition mechanism in TCE degradation was also demonstrated by comparing the strength of ROSs and PS utilization. In the presence of TW-80 (1 g L-1), over 97.5% TCE was removed at the PS/Fe(II)/CA/TCE molar ratio of 30/4/4/1, in which more than 86.7% TCE was dechlorinated. The result of scavenger experiments revealed that the dominant radicals were HO• and SO4-• in PS/Fe(II)/CA system in TW-80 containing aqueous solution, among which SO4-• performed a greater role in TCE removal. Moreover, over 85.3% TCE degradation in actual groundwater revealed the potential of PS/Fe(II)/CA process for actual groundwater remediation in containing TW-80 of TCE contaminant. This research provided a novel alternative technology for groundwater remediation with TCE contaminant when containing surfactants.