High-Performance Flexible Graphene Oxide-Based Moisture-Enabled Nanogenerator via Multilayer Heterojunction Engineering and Power Management System.

Recently, there has been a surge of interest in nanogenerators within the scientific community because their immense potential for extracting energy from the surrounding environment. A promising approach involves utilizing ambient moisture as an energy source for portable devices. In this study, moisture-enabled nanogenerators (MENGs) are devised by integrating heterojunctions of graphene oxide (GO) and reduced graphene oxide (rGO). Benefiting from the unique structure, a larger ion concentration gradient is achieved as well as a lower resistance, which leads to enhanced electricity generation. The resulting MENG generates a desirable open-circuit voltage of 0.76 V and a short-circuit current density of 73 µA cm-2 with a maximum power density of 15.8 µW cm-2 . Notably, the designed device exhibits a high voltage retention of more than 90% after 3000 bending cycles, suggesting a high potential for flexible applications. Moreover, a large-scale integrated MENG array is developed by incorporating flexible printed circuit technology and connecting it to a power management system. This integrated system can provide ample energy to operate an electronic ink display and drive a heart rate sensor for health monitoring. The outcomes of this research present a novel framework for advancing next-generation self-powered flexible devices, thereby demonstrating significant promise for future wearable electronics.

Recent Development of Moisture-Enabled-Electric Nanogenerators.

Power generation by converting energy from the ambient environment has been considered a promising strategy for developing decentralized electrification systems to complement the electricity supply for daily use. Wet gases, such as water evaporation or moisture in the atmosphere, can be utilized as a tremendous source of electricity by emerging power generation devices, that is, moisture-enabled-electric nanogenerators (MEENGs). As a promising technology, MEENGs provided a novel manner to generate electricity by harvesting energy from moisture, originating from the interactions between water molecules and hydrophilic functional groups. Though the remarkable progress of MEENGs has been achieved, a systematic review in this specific area is urgently needed to summarize previous works and provide sharp points to further develop low-cost and high-performing MEENGs through overcoming current limitations. Herein, the working mechanisms of MEENGs reported so far are comprehensively compared. Subsequently, a systematic summary of the materials selection and fabrication methods for currently reported MEENG construction is presented. Then, the improvement strategies and development directions of MEENG are provided. At last, the demonstrations of the applications assembled with MEENGs are extracted. This work aims to pave the way for the further MEENGs to break through the performance limitations and promote the popularization of future micron electronic self-powered equipment.

Stabilizing High-Voltage Performance of Nickel-Rich Cathodes via Facile Solvothermally Synthesized Niobium-Doped Strontium Titanate.

Ni-rich layered ternary cathodes are promising candidates thanks to their low toxic Co-content and high energy density (∼800 Wh/kg). However, a critical challenge in developing Ni-rich cathodes is to improve cyclic stability, especially under high voltage (>4.3 V), which directly affects the performance and lifespan of the battery. In this study, niobium-doped strontium titanate (Nb-STO) is successfully synthesized via a facile solvothermal method and used as a surface modification layer onto the LiNi0.8Co0.1Mn0.1O2 (NCM811) cathode. The results exhibited that the Nb-STO modification significantly improved the cycling stability of the cathode material even under high-voltage (4.5 V) operational conditions. In particular, the best sample in our work could provide a high discharge capacity of ∼190 mAh/g after 100 cycles under 1 C with capacity retention over 84% in the voltage range of 3.0-4.5 V, superior to the pristine NCM811 (∼61%) and pure STO modified STO-811-600 (∼76%) samples under the same conditions. The improved electrochemical performance and stability of NCM811 under high voltage should be attributed to not only preventing the dissolution of the transition metals, further reducing the electrolyte's degradation by the end of charge, but also alleviating the internal resistance growth from uncontrollable cathode-electrolyte interface (CEI) evolution. These findings suggest that the as-synthesized STO with an optimized Nb-doping ratio could be a promising candidate for stabilizing Ni-rich cathode materials to facilitate the widespread commercialization of Ni-rich cathodes in modern LIBs.

Multi-Interface Engineering of MXenes for Self-Powered Wearable Devices.

Self-powered wearable devices with integrated energy supply module and sensitive sensors have significantly blossomed for continuous monitoring of human activity and the surrounding environment in healthcare sectors. The emerging of MXene-based materials has brought research upsurge in the fields of energy and electronics, owing to their excellent electrochemical performance, large surface area, superior mechanical performance, and tunable interfacial properties, where their performance can be further boosted via multi-interface engineering. Herein, a comprehensive review of recent progress in MXenes for self-powered wearable devices is discussed from the aspects of multi-interface engineering. The fundamental properties of MXenes including electronic, mechanical, optical, and thermal characteristics are discussed in detail. Different from previous review works on MXenes, multi-interface engineering of MXenes from termination regulation to surface modification and their impact on the performance of materials and energy storage/conversion devices are summarized. Based on the interfacial manipulation strategies, potential applications of MXene-based self-powered wearable devices are outlined. Finally, proposals and perspectives are provided on the current challenges and future directions in MXene-based self-powered wearable devices.

Enhanced Piezocatalytic Performance of Li-doped BaTiO3 Through a Facile Sonication-Assisted Precipitation Approach.

Piezocatalysis-induced dye degradation has garnered significant attention as an effective method for addressing wastewater treatment challenges. In our study, we employed a room-temperature sonochemical method to synthesize piezoelectric barium titanate nanoparticles (BaTiO3: BTO) with varying levels of Li doping. This approach not only streamlined the sample preparation process but also significantly reduced the overall time required for synthesis, making it a highly efficient and practical method. One of the key findings was the exceptional performance of the Li-doped BTO nanoparticles. With 20 mg of Li additive, we achieved 90 % removal of Rhodamine B (RhB) dye within a relatively short timeframe of 150 minutes, all while subjecting the sample to ultrasonic vibration. This rapid and efficient dye degradation was further evidenced by the calculated kinetic rate constant, which indicated seven times faster degradation rate compared to pure BTO. The enhanced piezoelectric performance observed in the Li-doped BTO nanoparticles can be attributed to the strategic substitution of Li atoms, which facilitated a more efficient transfer of charge charges at the interface. Overall, our study underscores the potential of piezocatalysis coupled with advanced materials like Li-doped BTO nanoparticles as a viable and promising solution for wastewater treatment, offering both efficiency and environmental sustainability.

Big Data Analytics on Lung Cancer Diagnosis Framework With Deep Learning.

As the segment of diseased tissue in PET images is time-consuming, laborious and low accuracy, this work proposes an automated framework for PET image screening, denoising and diseased tissue segmentation. First, taking into account the characteristics of PET images, the framework uses a differential activation filter to select whole-body images containing lesion tissue. Second, a new neural network containing residual connections which has powerful generalization performance compared with normal FCN network is proposed for PET image reconstruction and denoising. Finally, in the segmentation of lesion tissues, a custom clustering algorithm based on the density is used to distinguishe the lesion tissue part from the normal tissue. Tests on real medical PET images show that the whole automated framework has good performance and time cost in PET lesion image screening, image denoising and lesion tissue segmentation compared with other algorithms. The framework shows promising scientific study and application prospects.

Engineering work functions of cobalt-doped manganese oxide based electrocatalysts for highly efficient oxygen evolution reaction.

The crystalline and electronic structures are two important factors for the design of electrocatalysts. In this work, Co-doped MnO electrocatalysts grown on nickel foam (NF) were prepared by a facile hydrothermal reaction, followed by H2 treatment process. The electrocatalytic performance of MnO was significantly improved after doping with Co and the Co0.1Mn0.9O-NF sample achieved excellent oxygen evolution reaction (OER) performance with low overpotential (370 mV at 10 mA cm-2) and reasonable Tafel slope (85.6 mV dec-1). Significantly, the low work function was obtained in the Co0.1Mn0.9O-NF sample (4.37 eV), which could accelerate the charge transfer process of the OER activity. The excellent OER performance of the Co0.1Mn0.9O-NF sample is also attributed to the rich active sites, which improved electrical conductivity and enlarged electrochemical surface areas.

Dual-modification of Ni-rich cathode materials through strontium titanate coating and thermal treatment.

Ni-rich layered structure ternary oxides, such as LiNi0.8Co0.1Mn0.1O2 (NCM811), are promising cathode materials for high-energy lithium-ion batteries (LIBs). However, a trade-off between high capacity and long cycle life still obstructs the commercialization of Ni-rich cathodes in modern LIBs. Herein, a facile dual modification approach for improving the electrochemical performance of NCM811 was enabled by a typical perovskite oxide: strontium titanate (SrTiO3). With a suitable thermal treatment, the modified cathode exhibited an outstanding electrochemical performance that could deliver a high discharge capacity of 188.5 mAh/g after 200 cycles under 1C with a capacity retention of 90%. The SrTiO3 (STO) protective layer can effectively suppress the side reaction between the NCM811 and the electrolyte. In the meantime, the pillar effect provided by interfacial Ti doping could effectively reduce the Li+/Ni2+ mixing ratio on the NCM811 surface and offer more efficient Li+ migration between the cathode and the coating layer after post-thermal treatment (≥600 °C). This dual modification strategy not only significantly improves the structural stability of Ni-rich layered structure but also enhances the electrochemical kinetics via increasing diffusion rate of Li+. The electrochemical measurement results further disclosed that the 3 wt% STO coated NCM811 with 600 °C annealing exhibits the best performance compared with other control samples, suggesting an appropriate temperature range for STO coated NCM811 cathode is critical for maintaining a stable structure for the whole system. This work may offer an effective option to enhance the electrochemical performance of Ni-rich cathodes for high-performance LIBs.

Enhancing the Electrochemical Properties of Nickel-Rich Cathode by Surface Coating with Defect-Rich Strontium Titanate.

Ni-rich layered ternary cathodes (i.e., LiNixCoyMzO2, M = Mn or Al, x + y + z = 1 and x ≥ 0.8) are promising candidates for the power supply of portable electronic devices and electric vehicles. However, the relatively high content of Ni4+ in the charged state shortens their lifespan due to inevitable capacity and voltage deteriorations during cycling. Therefore, the dilemma between high output energy and long cycle life needs to be addressed to facilitate more widespread commercialization of Ni-rich cathodes in modern lithium-ion batteries (LIBs). This work presents a facile surface modification approach with defect-rich strontium titanate (SrTiO3-x) coating on a typical Ni-rich cathode: LiNi0.8Co0.15Al0.05O2 (NCA). The defect-rich SrTiO3-x-modified NCA exhibits enhanced electrochemical performance compared to its pristine counterpart. In particular, the optimized sample delivers a high discharge capacity of ∼170 mA h/g after 200 cycles under 1C with capacity retention over 81.1%. The postmortem analysis provides new insight into the improved electrochemical properties which are ascribed to the SrTiO3-x coating layer. This layer appears to not only alleviate the internal resistance growth, from uncontrollable cathode-electrolyte interface evolution, but also acts as a lithium diffusion channel during prolonged cycling. Therefore, this work offers a feasible strategy to improve the electrochemical performance of layered cathodes with high nickel content for next-generation LIBs.

Relieving Stress Concentration through Anion-Cation Codoping toward Highly Stable Nickel-Rich Cathode.

Nickel-rich LiNi0.8Co0.15Al0.015O2 (NCA) with excellent energy density is considered one of the most promising cathodes for lithium-ion batteries. Nevertheless, the stress concentration caused by Li+/Ni2+ mixing and oxygen vacancies leads to the structural collapse and obvious capacity degradation of NCA. Herein, a facile codoping of anion (F-)-cation (Mg2+) strategy is proposed to address these problems. Benefiting from the synergistic effect of F- and Mg2+, the codoped material exhibits alleviated Li+/Ni2+ mixing and demonstrates enhanced electrochemical performance at high voltage (≥4.5 V), outperformed the pristine and F-/Mg2+ single-doped counterparts. Combined experimental and theoretical studies reveal that Mg2+ and F- codoping decreases the Li+ diffusion energy barrier and enhances the Li+ transport kinetics. In particular, the codoping synergistically suppresses the Li+/Ni2+ mixing and lattice oxygen escape, and alleviates the stress-strain accumulation, thereby inhibiting crack propagation and improving the electrochemical performance of the NCA. As a consequence, the designed Li0.99Mg0.01Ni0.8Co0.15Al0.05O0.98F0.02 (Mg1+F2) demonstrates a much higher capacity retention of 82.65% than NCA (55.69%) even after 200 cycles at 2.8-4.5 V under 1 C. Furthermore, the capacity retention rate of the Mg1+F2||graphite pouch cell after 500 cycles is 89.6% compared to that of the NCA (only 79.4%).

Cationic Interstitials: An Overlooked Ionic Defect in Memristors.

Metal oxide-based memristors are promising candidates for breaking through the limitations in data storage density and transmission efficiency in traditional von Neumann systems, owing to their great potential in multi-state data storage and achievement of the in-memory neuromorphic computing paradigm. Currently, the resistive switching behavior of those is mainly ascribed to the formation and rupture of conductive filaments or paths formed by the migration of cations from electrodes or oxygen vacancies in oxides. However, due to the relatively low stability and endurance of the cations from electrodes, and the high mobility and weak immunity of oxygen vacancies, intermediate resistance states can be hardly retained for multilevel or synaptic resistive switching. Herein, we reviewed the memristors based on cationic interstitials which have been overlooked in achieving digital or analog resistive switching processes. Both theoretical calculations and experimental works have been surveyed, which may provide reference and inspiration for the rational design of multifunctional memristors, and will promote the increments in the memristor fabrications.

Enhancing cyclic and in-air stability of Ni-Rich cathodes through perovskite oxide surface coating.

Ni-rich layered oxides, such as LiNi0.8Co0.1Mn0.1O2 (NCM811), are promising cathode materials for high-energy lithium-ion batteries. However, the relatively high reactivity of Ni in NCM811 cathodes results in severe capacity fading originating from the undesired side reactions that occur at the cathode-electrolyte interface during prolonged cycling. Therefore, the trade-off between high capacity and long cycle life can obstruct the commercialization process of Ni-rich cathodes in modern lithium-ion batteries (LIBs). In addition, high sensitivity toward air upon storage greatly limits the commercial application. Herein, a facile surface modification strategy is introduced to enhance the cycling and in-air storage stability of NCM811. The NCM811 with a uniform SrTiO3 (STO) nano-coating layer exhibited outstanding electrochemical performances that could deliver a high discharge capacity of 173.5 mAh⋅g-1 after 200 cycles under 1C with a capacity retention of 90%. In contrast, the uncoated NCM811 only provided 65% capacity retention of 130.8 mAh⋅g-1 under the same conditions. Structural evolution analysis suggested that the STO coating acted as a buffer layer to suppress the dissolution of transition metal ions caused by the HF attack from the electrolyte and promote the lithium diffusion during the charge-discharge process. In addition, the constructed STO layer prevented the exposure of NCM811 to H2O and CO2 and thus effectively improved the in-air storage stability. This work offers an effective way to enhance the performance stability of Ni-rich oxides for high-performance cathodes of lithium-ion batteries.

Hydrothermally activated TiO2 nanoparticles with a C-dot/g-C3N4 heterostructure for photocatalytic enhancement.

Dye degradation via photocatalysis technology has been investigated intensively to tackle environmental issues and energy crisis concerns. In this study, a newly designed ternary photocatalyst was facilely prepared by a simple one-pot hydrothermal process by directly mixing TiO2 nanoparticles with carbon dots (C-dots) and graphitic carbon nitride (g-C3N4). The optimized precursor treatments and heterostructure components show significantly enhanced photodegradation activity towards organic dyes Rhodamine B (RhB) and methylene blue (MB). Excellent photocatalytic activities were achieved owing to the better attachment of anatase-type TiO2 nanoparticle-aggregations to the C-dots/g-C3N4 (CC) nanocomposite, which impressively displays superhydrophilicity by employing the hydrothermal activation process. FT-IR spectra revealed that the hydrothermal treatment could remarkably increase the coupling interactions between TiO2 nanoparticles and the CC nanosheets within the ternary catalyst, enhancing the photocatalytic activity. Thus, it was concluded that this ternary photocatalyst is highly suitable for the remediation of dye-contaminated wastewater.

Facile Patterning of Silver Nanowires with Controlled Polarities via Inkjet-Assisted Manipulation of Interface Adhesion.

Facile patterning technologies of silver nanowires (AgNWs) with low-cost, high-resolution, designable, scalable, substrate-independent, and transferable characteristics are highly desired. However, it remains a grand challenge for any material processing method to fulfil all desirable features. Herein, a new patterning method is introduced by combining inkjet printing with adhesion manipulation of substrate interfaces. Both positive and negative patterns (i.e., AgNW grid and rectangular patterns) have been simultaneously achieved, and the pattern polarity can be reversed through adhesion modification with judiciously selected supporting layers. The electrical performance of the AgNW grids depends on the AgNW interlocking structure, manifesting a strong structure-property correlation. High-resolution and complex AgNW patterns with line width and spacing as small as 10 µm have been demonstrated through selective deposition of poly(methyl methacrylate) layers. In addition, customized AgNW patterns, such as logos and words, can be fabricated onto A4-size samples and subsequently transferred to targeted substrates, including Si wafers, a curved glass vial, and a beaker. This reported inkjet-assisted process therefore offers a new effective route to manipulate AgNWs for advanced device applications.

Improving thermal and electrical stability of silver nanowire network electrodes through integrating graphene oxide intermediate layers.

Silver nanowire (Ag NW)-based flexible and transparent electrodes are a promising candidate for various electronic and optoelectronic applications. However, thermal and electrical instabilities of Ag NW networks during operation and post treatments need to be improved for practical applications. In this work, Ag NW/Graphene Oxide (GO) hybrid films with a multilayer structure were developed, in which transparent GO sheets were inserted between Ag NWs. For the pristine Ag NW networks, contacted NWs exhibited poorer thermal stability than individual NWs as faster Ag diffusion between NWs led to the breakage of the junctions at working temperatures, hence leading to the overall device failure. In contrast, the GO intermediate layers hindered the Ag diffusion between NWs in the Ag NW/Graphene Oxide hybrid films and maintained the junction structure, giving rise to enhanced thermal stability compared to the pristine networks and the GO-covered samples. For electrical tests, unlike the network degradation under annealing treatments, a local deterioration perpendicular to the current flow was directly observed after electrical breakdown, which was attributed to high local temperature under large applied voltage. The electrical failure of the devices was related to the network structure and defects. Furthermore, the pristine devices showed notable variation of failure voltage, which in the hybrid devices is more uniform and improved in general.

Tunable resistance switching in solution processed chromium-doped strontium titanate nanoparticles films.

In this work, resistance switching behaviours in solution processed chromium (Cr)-doped strontium titanate (SrTiO3) films have been investigated. Undoped SrTiO3 film shows I-V characteristics of typical nonlinear resistor and no resistance hysteresis loops are observed. On the contrary, Cr-doped SrTiO3 films show stable and reversible hysteresis loops, which can be controlled by applying different voltage bias. Based on a series of characterization results, including X-ray diffraction (XRD), Raman and X-ray photoelectron spectroscopy (XPS), we infer that Ti4+ is substituted by Cr3+, giving rise to increased concentration of oxygen vacancies. Therefore, the observed resistance switching phenomenon is attributed to voltage driven oxygen vacancy migration. Furthermore, gradually decreased overall resistance is also realized under repeated sweeping cycles.