RESUMEN
Increased antibiotic use worldwide has become a major concern because of their health and environmental impacts. Since most antibiotic residues can hardly be removed from wastewater using conventional treatments, alternative methods receive great attention. Adsorption is one of the most efficient and cost-effective treatment methods for antibiotics. Among the adsorbents, clay minerals have garnered increasing attention due to their unique properties including availability, high specific surface area, low cost, cation exchange capacity, and good removal efficiency. This paper reviews the recent progress made in the use of natural and modified clay minerals for the removal of antibiotics from water. First, the sources, occurrence, removal and health effects of the antibiotics commonly encountered in water bodies are described. Antibiotic concentration levels and average removal efficiencies measured in conventional activated sludge treatment systems worldwide are also provided to better address the problem. Second, the review explores the characteristics of clay minerals as adsorbent of antibiotics and the factors affecting the adsorption. The review identifies and discusses the future trends and strategies used to increase the adsorption capacity of clay minerals by modification and combination techniques (intercalation of novel functional groups such as organocations, biopolymers and metal pillared-clay minerals, combination with biochar or thermal activation). The quantitative comparisons of clay minerals' ability for antibiotic removal are given. Some natural clay minerals have good removal potential for antibiotics, with maximum adsorption capacities over 100 mg/g. For most other adsorbents, surface modifications and combination techniques resulted in improved adsorption properties (including higher surface area, enhanced adsorption capacity, increased stability and mechanical strength). Finally, the application of these adsorbents at pilot scale, using real wastewater samples, their reuse, economic analysis and life cycle assessment are other issues that have been considered.
Asunto(s)
Aguas Residuales , Contaminantes Químicos del Agua , Adsorción , Antibacterianos/química , Arcilla , Minerales , Aguas Residuales/química , Agua/análisis , Contaminantes Químicos del Agua/químicaRESUMEN
The development of biobased polymeric materials for wastewater purification has become a demand due to the growing need for water free of hazardous metal ions for safe purposes. The organic components of the OLLW including carbohydrates, phenolics, aromatic acids and others are cost-effective and sustainable choices for this application. This work focuses on a method for turning the organic components of liquid waste from the olive industry (OILW) into a foam-based value-added polymer that has several metal ion binding sites. The process of making the target polymers involved reacting the components of the OILW with hexamethylene diisocyante and 1,4-phnyelene diisocynate to create the polymeric materials LHMIDIC and LPDIC that are in foam forms with urethane linkages, respectively. The adsorption competence of the polymeric foams toward Pb(II) was evaluated as a function of various parameters including adsorbent dose, pH, temperature, initial ion concentration and time. The optimum parameters values that led to a quantitative removal of Pb(II) were identified. The obtained thermodynamic parameters showed that the adsorption by the two foams was spontaneous at room temperature. The isothermal and kinetic values showed that the adsorption by synthesized foams follows a second order kinetic and obeys the Langmuir isothermal model. The foams showed a high tendency for removing multi metal ions present in a real sample of wastewater. The original nature of the starting material used in making the foam, cost and the obtained results showed the potential of using the foam in a large-scale plants of wastewater purification.
RESUMEN
Pharmaceutical residues in water and wastewater have become a worldwide problem with environmental and public health consequences. Antibiotics are of special importance because of the emergence of antibiotic-resistant genes. This study evaluates the adsorptive removal of four common fluoroquinolone antibiotics by using natural colemanite as an alternative adsorbent for the first time. Batch adsorption experiments were conducted for the mixture of fluoroquinolones as well as for individual compounds during the isotherm studies. Adsorption kinetic results indicated that the process followed the pseudo-second-order (PSO) model, while the Langmuir model described the sorption isotherms. The effects of pH and temperature on adsorption performance were determined, and the results indicated that the adsorption was endothermic and spontaneous, with increasing randomness at the solid-liquid interface. The effects of real water and wastewater matrices were tested by using tap water, surface water, and wastewater samples. Reusability experiments based on five adsorption-desorption cycles indicated that the adsorption performance was mostly retained after five cycles. The adsorption mechanism was elucidated based the material characterization before and after adsorption. The results indicate that colemanite can be used as an effective and reusable adsorbent for fluoroquinolone antibiotics as well as for other pollutants with similar physicochemical properties.
Asunto(s)
Contaminantes Químicos del Agua , Purificación del Agua , Agua , Aguas Residuales , Adsorción , Purificación del Agua/métodos , Fluoroquinolonas , Antibacterianos , Contaminantes Químicos del Agua/análisis , Cinética , Concentración de Iones de Hidrógeno , TermodinámicaRESUMEN
In this work, we present a process for converting olive industry solid waste (OISW) into a value-added material with ionic receptors for use in the removal of toxic metal ions from wastewater. This 3D polymer is a promising adsorbent for large-scale application, since it is a low-cost material made from agricultural waste and showed exceptional performance. The synthesis of the network polymer involved the carboxymethylation of OISW and curing of the carboxymethylated OISW at an elevated temperature to promote the formation of ester linkages between OISW's components. FT-IR, atomic force microscopy, and thermal analysis were performed on the crosslinked product. The adsorption efficiency of the crosslinked carboxymethylated OISW toward Pb(II), Cu(II), and other toxic metal ions present in sewage was evaluated as a function of adsorbent dose, temperature, pH, time, and initial metal ion. The percentage removal of about 20 metal ions present in a sewage sample collected from a sewer plant located in the Palestinian Territories was determined. The adsorption efficiency did not drop even after six cycles of use. The kinetic study showed that the adsorption process follows the Langmuir isotherm model and the second-order adsorption rate. The experimental Qe values of 13.91 and 13.71 mg/g were obtained for Pb(II) and Cu(II) removal, respectively. The thermodynamic results confirm the spontaneous metal bonding to the receptor sites of the crosslinked carboxymethylated OISW.
RESUMEN
Contamination in water is due to various environmental pollutants from natural and anthropogen activities. To remove toxic metals from contaminated water, we developed a novel adsorbent in foam form based on an olive industry waste material. The foam synthesis involved oxidation of cellulose extracted from the waste to dialdehyde, functionalization of the cellulose dialdehyde with an amino acid group, reacting the functionalized cellulose with hexamethylene diisocyanate and p-phenylene diisocyanate to produce the target polyurethanes Cell-F-HMDIC and Cell-F-PDIC, respectively. The optimum condition for lead(II) adsorption by Cell-F-HMDIC and Cell-F-PDIC were determined. The foams show the ability to quantitatively remove most of metal ions present in a real sample of sewage. The kinetic and thermodynamic studies confirmed a spontaneous metal ion binding to the foams with a second pseudo-order adsorption rate. The adsorption study revealed it obeys the Langmuir isotherm model. The experimental Qe values of both foams Cell-F-PDIC and Cell-F-HMDIC were 2.1929 and 2.0345 mg/g, respectively. Monte Carlo (MC) and Dynamic (MD) and simulations showed excellent affinity of both foams for lead ions with high adsorption negative energy value indicating vigorous interactions of Pb(II) with the adsorbent surface. The results indicate the usefulness of the developed foam in commercial applications. ENVIRONMENTAL IMPLICATION: Elimination of metal ions from contaminated environments is important for a number of reasons. They are toxic to humans via interaction with biomolecules, resulting in disruption of the metabolism and biological activities of many proteins. They are toxic to plants. Industrial effluents and/or wastewater discharged from production processes, contain a considerable amount of metal ions. In this work, the use of naturally produced materials, such as olive waste biomass, as adsorbents for environmental remediation has received great attention. This biomass represents unused resources and presents serious disposal problems. We demonstrated that such materials are capable of selectively adsorbing metal ions.
Asunto(s)
Metales Pesados , Contaminantes Químicos del Agua , Purificación del Agua , Humanos , Celulosa/química , Poliuretanos , Aminoácidos , Metales , Purificación del Agua/métodos , Iones , Agua , Adsorción , Contaminantes Químicos del Agua/química , Cinética , Concentración de Iones de HidrógenoRESUMEN
In this study, the potential use of phosphonated Halomonas Levan (PhHL) as a natural and cost effective adsorbent for Bisphenol A (BPA), was systematically investigated via the study of the adsorption equilibrium, kinetics, and reuse potential as well as the interpretation of adsorption mechanism. The effects of pH and temperature on the adsorption were also evaluated. The maximum amount of BPA adsorbed on the unit weight of PhHL was determined as 104.8 (∓5.02) mg/g (at 298â¯K) and the maximum adsorption capacity was calculated as 126.6â¯mg/g by Sips model. FTIR and XPS studies were conducted to elucidate the adsorption mechanism. Based on the obtained results OH-pi and CH-pi interactions were found to be effective in the adsorption mechanism. The reuse ability was studied with three cycles of adsorption-desorption, and the results showed that the BPA adsorbed per gram of the PhHL decreased 28.6% after the third cycle. This study has shown that PhHL can be used as an effective adsorbent for the removal of BPA from aqueous solutions. The obtained results may be useful in the development of PhHL based adsorption systems for the removal of EDCs with similar chemical properties to BPA.
Asunto(s)
Compuestos de Bencidrilo/análisis , Fructanos/química , Fenoles/análisis , Purificación del Agua/métodos , Adsorción , Análisis Costo-Beneficio , Halomonas/química , Concentración de Iones de Hidrógeno , Cinética , Microscopía Electrónica de Rastreo , Ácidos Fosforosos/química , Espectrometría por Rayos X , Espectroscopía Infrarroja por Transformada de Fourier , Temperatura , Agua , Contaminantes Químicos del Agua/análisis , Purificación del Agua/instrumentaciónRESUMEN
Levan is a fructan type polysaccharide that has long been considered as an industrially important biopolymer however its limited availability is mainly due to the bottlenecks associated with its large-scale production. To overcome such bottlenecks in the commercialization of this very promising polysaccharide, co-production of levan with polyhydroxyalkanoates (PHAs) by halophilic Halomonas smyrnensis cultures has been proposed in this study for the first time. After in silico and in vitro assessment of PHA accumulation, fermentation profiles for levan and PHA concentrations were obtained in the presence of sucrose and glucose and the PHA granules observed by TEM were found to be poly(3-hydroxybutyrate) (PHB) after detailed structural characterization by GC-MS, DSC, FTIR and NMR. Six nutrient limitation strategies based on nitrogen (N) and phosphorus (P) were tested but highest levan and PHB yields were obtained under unlimited conditions. H. smyrnensis is proved to co-produce PHB and levan while using inexpensive carbon sources which is a commercially successful microbial cell factory system showing a great potential in lowering manufacturing costs and aiming for a zero waste policy within the biorefinery concept.