RESUMEN
Paraffin (PA)/expanded graphite (EG) is an important composite phase change material with low cost, high heat storage, good thermal conductivity and cycling stability. Its thermal conductivity needs to be further improved for application in the thermal management system of power lithium-ion batteries. In this paper, copper plated expanded graphite (CPEG) with 3D porous structure was prepared by electroless copper plating method, which was used as thermal conductivity enhancing material to replace part of EG in PA/EG composite materials. For the optimized phase change material composed of 80 %PA-14 %EG-6 %CPEG, the copper content is very low (0.768â wt %), but its thermal conductivity can be significantly improved without loss of latent heat and thermal cycling stability. Its thermal conductivity is increased from 11â times to 16.5â times that of paraffin while compared with the copper-free composite material (80 %PA-20 %EG). The PA/EG/CPEG composite material exhibits good temperature control effect on power lithium-ion batteries.
RESUMEN
Na4Fe3(PO4)2P2O7/C (NFPP) is a promising cathode material for sodium-ion batteries, but its electrochemical performance is heavily impeded by its low electronic conductivity. To address this, pure-phase Mo6+-doped Na4Fe3-xMox(PO4)2P2O7/C (Mox-NFPP, x = 0, 0.05, 0.10, 0.15) with the Pn21a space group is successfully synthesized through spray drying and annealing methods. Density functional theory (DFT) calculations reveal that Mo6+ doping facilitates the transition of electrons from the valence to the conduction band, thus enhancing the intrinsic electron conductivity of Mox-NFPP. With an optimal Mo6+ doping level of x = 0.10, Mo0.10-NFPP exhibits lower charge transfer resistance, higher sodium-ion diffusion coefficients, and superior rate performance. As a result, the Mo0.10-NFPP cathode offers an initial discharge capacity of up to 123.9 mAh g-1 at 0.1 C, nearly reaching its theoretical capacity. Even at a high rate of 10 C, it delivers a high discharge capacity of 86.09 mAh g-1, maintaining 96.18% of its capacity after 500 cycles. This research presents a new and straightforward strategy to enhance the electrochemical performance of NFPP cathode materials for sodium-ion batteries.
RESUMEN
The morphology of metal oxide nanostructures influences the response of the materials in a given application. In addition to changing the composition, doping can also modify the morphology of a host nanomaterial. Herein, we determine the effect of dopant concentration, reaction temperature, and reaction time on the morphology and assembly of CoxZn1−xO nanoparticles synthesized through non-aqueous sol-gel in benzyl alcohol. With the increase of the atom % of cobalt incorporated from 0 to 15, the shape of the nanoparticles changes from near spherical, to irregular, and finally to triangular. The tendency of the particles to assemble increases in the same direction, with Co0.05Zn0.95O consisting of non-assembled particles, whereas Co0.15Zn0.85O consists of triangular nanoparticles forming spherical structures. The morphology and assembly process are also sensitive to the reaction temperature. The assembly process is found to occur during the nucleation or the early stages of particle growth. The cobalt ions promote the change in the shape during the growth stage of the nanoparticles.
RESUMEN
A novel approach was developed to sort a large-diameter semiconducting single-walled carbon nanotube (sc-SWCNT) based on copolyfluorene derivative with high yield. High purity sc-SWCNTs inks were obtained by wrapping arc-discharge SWCNTs with poly[2,7-(9,9-dioctylfluorene)-alt-4,7-bis(thiophen-2-yl)benzo-2,1,3-thiadiazole] (PFO-DBT) aided by sonication and centrifugation in tetrahydrofuran (THF). The sorted sc-SWCNT inks and nanosilver inks were used to print top-gated thin-film transistors (TFTs) on flexible substrates with an aerosol jet printer. The printed TFTs demonstrated low operating voltage, small hysteresis, high on-state current (up to 10(-3) A), high mobility and on-off ratio. An organic light emitting diode (OLED) driving circuit was constructed based on the printed TFTs, which exhibited high on-off ratio up to 10(4) and output current up to 3.5 × 10(-4) A at V(scan) = -4.5 V and Vdd = 0.8 V. A single OLED was switched on with the driving circuit, showing the potential as backplanes for active matrix OLED applications.