Performance Enhancement of Lead-Free 2D Tin Halide Perovskite Transistors by Surface Passivation and Its Impact on Non-Volatile Photomemory Characteristics.

Two-dimensional (2D) tin (Sn)-based perovskites have recently received increasing research attention for perovskite transistor application. Although some progress is made, Sn-based perovskites have long suffered from easy oxidation from Sn2+ to Sn4+ , leading to undesirable p-doping and instability. In this study, it is demonstrated that surface passivation by phenethylammonium iodide (PEAI) and 4-fluorophenethylammonium iodide (FPEAI) effectively passivates surface defects in 2D phenethylammonium tin iodide (PEA2 SnI4 ) films, increases the grain size by surface recrystallization, and p-dopes the PEA2 SnI4 film to form a better energy-level alignment with the electrodes and promote charge transport properties. As a result, the passivated devices exhibit better ambient and gate bias stability, improved photo-response, and higher mobility, for example, 2.96 cm2 V-1 s-1 for the FPEAI-passivated films-four times higher than the control film (0.76 cm2 V-1 s-1 ). In addition, these perovskite transistors display non-volatile photomemory characteristics and are used as perovskite-transistor-based memories. Although the reduction of surface defects in perovskite films results in reduced charge retention time due to lower trap density, these passivated devices with better photoresponse and air stability show promise for future photomemory applications.

High-performance solar flow battery powered by a perovskite/silicon tandem solar cell.

The fast penetration of electrification in rural areas calls for the development of competitive decentralized approaches. A promising solution is represented by low-cost and compact integrated solar flow batteries; however, obtaining high energy conversion performance and long device lifetime simultaneously in these systems has been challenging. Here, we use high-efficiency perovskite/silicon tandem solar cells and redox flow batteries based on robust BTMAP-Vi/NMe-TEMPO redox couples to realize a high-performance and stable solar flow battery device. Numerical analysis methods enable the rational design of both components, achieving an optimal voltage match. These efforts led to a solar-to-output electricity efficiency of 20.1% for solar flow batteries, as well as improved device lifetime, solar power conversion utilization ratio and capacity utilization rate. The conceptual design strategy presented here also suggests general future optimization approaches for integrated solar energy conversion and storage systems.

Magnetic optical rotary dispersion and magnetic circular dichroism in methylammonium lead halide perovskites.

Large magnetic optical rotary dispersion (Faraday rotation) has been demonstrated recently in methylammonium lead bromide. Here, we investigate the prospect of extending the active spectral range by altering the halogen. We also investigate the origins of large Faraday rotation in these diamagnetic materials using magnetic circular dichroism (MCD) spectroscopy and the Kramers-Kronig relations. We find that, while MAPbCl3 (MA = methylammonium) single crystals exhibit a large Verdet constant in the blue, no appreciable Faraday rotation is observed in the red/near infra-red for MAPbI3 single crystals. However, in all film samples, we find clear evidence of large MCD resulting from the Zeeman splitting of the highly resonant 1s exciton state. Our Kramers-Kronig calculations of Faraday rotation based on MCD data matches well with the dispersion of our experimental data for MAPbCl3 and MAPbBr3 , with some deviation in magnitude-demonstrating the excitonic nature of Faraday rotation in these materials. However, our calculations predict significant Faraday rotation in MAPbI3 , contrary to our experimental results, indicating a potential discrepancy between the properties of the thin film and single crystal.

Unveiling the Relationship between the Perovskite Precursor Solution and the Resulting Device Performance.

For the fabrication of perovskite solar cells (PSCs) using a solution process, it is essential to understand the characteristics of the perovskite precursor solution to achieve high performance and reproducibility. The colloids (iodoplumbates) in the perovskite precursors under various conditions were investigated by UV-visible absorption, dynamic light scattering, photoluminescence, and total internal reflection fluorescence microscopy techniques. Their local structure was examined by in situ X-ray absorption fine structure studies. Perovskite thin films on a substrate with precursor solutions were characterized by transmission electron microscopy, X-ray diffraction analysis, space-charge-limited current, and Kelvin probe force microscopy. The colloidal properties of the perovskite precursor solutions were found to be directly correlated with the defect concentration and crystallinity of the perovskite film. This work provides guidelines for controlling perovskite films by varying the precursor solution, making it possible to use colloid-engineered lead halide perovskite layers to fabricate efficient PSCs.

Application of polydimethylsiloxane surface texturing on III-V//Si tandem achieving more than 2 % absolute efficiency improvement.

Silicon based multi-junction solar cells are a promising approach for achieving high power conversion efficiencies using relatively low-cost substrates. In recent years, 2-terminal triple-junction solar cells using GaInP/GaAs as top cells and Si bottom cell have achieved excellent efficiencies. Epitaxial growth or wafer bonding has been used for the integration of the cells. This requires the top surface of the Si cell to be polished for effective integration, sacrificing the light trapping in the Si cell. The poor long wavelength light absorption in silicon limits the tandem cell efficiency as it is limited by current mismatch. In this work, for the first time, an external surface texturing is attached onto a GaInP/GaAs//Si wafer bonded triple-junction solar cell, using polydimethylsiloxane (PDMS) layers with surface geometries replicated from various pyramidally-textured silicon wafers. With reduced reflection, the short circuit current density is increased by 0.95 mA/cm2, while the overall cell efficiency is boosted by more than 2 % absolute.

The Impact of a Dynamic Two-Step Solution Process on Film Formation of Cs0.15 (MA0.7 FA0.3 )0.85 PbI3 Perovskite and Solar Cell Performance.

This paper provides deep understanding of the formation mechanism of perovskite film fabricated by sequential solution-based methods. It compares two sequential spin-coating methods for Cs0.15 (MA0.7 FA0.3 )0.85 PbI3 perovskite. First is the "static process," with a stoppage between the two spin-coating steps (1st PbI2 -CsI-dimethyl sulfoxide (DMSO)-dimethylformamide (DMF) and 2nd methylammonium iodide (MAI)-formamidinium iodide (FAI)-isopropyl alcohol). Second is the "dynamic process," where the 2nd precursor is dispensed while the substrate is still spinning from the 1st step. For the first time, such a dynamic process is used for Cs0.15 (MA0.7 FA0.3 )0.85 PbI3 perovskite. Characterizations reveal improved film formation with the dynamic process due to the "retainment" of DMSO-complex necessary for the intermediate phase which i) promotes intercalation between precursors and ii) slows down perovskite crystallization for full conversion. The comparison on as-deposited perovskite before annealing indicates a more ordered film using this dynamic process. This results in a thicker, more uniform film with higher degree of preferred crystal orientation and higher carrier lifetime after annealing. Therefore, dynamic-processed devices present better performance repeatability, achieving a higher average efficiency of 17.0% compared to static ones (15.0%). The new insights provided by this work are important for perovskite solar cells processed sequentially as the process has greater flexibility in resolving solvent incompatibility, allowing separate optimizations and allowing different deposition methods.

Light-activated inorganic CsPbBr2I perovskite for room-temperature self-powered chemical sensing.

Halide perovskite materials are excellent light harvesters that have generated enormous interest for photovoltaic technology and an increasing number of other optoelectronic applications. Very recently, their use for miniaturized chemical sensors has shown a promising room-temperature response. Here, we present some insights on the use of CsPbBr2I (CPBI) perovskites for self-powered room-temperature sensing of several environmentally and medically relevant compounds demonstrating rapid detection of down to concentrations of 1 ppm. Notably, the photocurrent of these self-powered CPBI-based devices increases under exposure to both reducing (e.g. acetone, propane) and oxidizing (e.g. NO2, O2) gas molecules and decreases rapidly upon reverting to an inert atmosphere. In situ photoluminescence (PL) analysis of the CPBI during exposure to oxidizing molecules reveals a strongly increased PL intensity and longer lifetime indicating a prevalent role of CPBI trap states in the sensing mechanism. These findings provide new insights for the engineering of perovskite-based materials for their future chemical sensing applications.

Superior Self-Powered Room-Temperature Chemical Sensing with Light-Activated Inorganic Halides Perovskites.

Hybrid halide perovskite is one of the promising light absorber and is intensively investigated for many optoelectronic applications. Here, the first prototype of a self-powered inorganic halides perovskite for chemical gas sensing at room temperature under visible-light irradiation is presented. These devices consist of porous network of CsPbBr3 (CPB) and can generate an open-circuit voltage of 0.87 V under visible-light irradiation, which can be used to detect various concentrations of O2 and parts per million concentrations of medically relevant volatile organic compounds such as acetone and ethanol with very quick response and recovery time. It is observed that O2 gas can passivate the surface trap sites in CPB and the ambipolar charge transport in the perovskite layer results in a distinct sensing mechanism compared with established semiconductors with symmetric electrical response to both oxidizing and reducing gases. The platform of CPB-based gas sensor provides new insights for the emerging area of wearable sensors for personalized and preventive medicine.

Spectral dependence of direct and trap-mediated recombination processes in lead halide perovskites using time resolved microwave conductivity.

Elucidating the decay mechanisms of photoexcited charge carriers is key to improving the efficiency of solar cells based on organo-lead halide perovskites. Here we investigate the spectral dependence (via above-, inter- and sub-bandgap optical excitations) of direct and trap-mediated decay processes in CH3NH3PbI3 using time resolved microwave conductivity (TRMC). We find that the total end-of-pulse mobility is excitation wavelength dependent - the mobility is maximized (172 cm(2) V(-1) s(-1)) when charge carriers are excited by near bandgap light (780 nm) in the low charge carrier density regime (10(9) photons per cm(2)), and is lower for above- and sub-bandgap excitations. Direct recombination is found to occur on the 100-400 ns timescale across excitation wavelengths near and above the bandgap, whereas indirect recombination processes displayed distinct behaviour following above- and sub-bandgap excitations, suggesting the influence of different trap distributions on recombination dynamics.

Mobile Charge-Induced Fluorescence Intermittency in Methylammonium Lead Bromide Perovskite.

Organic-inorganic halide perovskite has emerged as a very promising material for solar cells due to its excellent photovoltaic enabling properties resulting in rapid increase in device efficiency over the last 3 years. Extensive knowledge and in-depth physical understanding in the excited state carrier dynamics are urgently required. Here we investigate the fluorescence intermittency (also known as blinking) in vapor-assisted fabricated CH3NH3PbBr3 perovskite. The evident fluorescence blinking is observed in a dense CH3NH3PbBr3 perovskite film that is composed of nanoparticles in close contact with each other. In the case of an isolated nanoparticle no fluorescence blinking is observed. The "ON" probability of fluorescence is dependent on the excitation intensity and exhibits a similar power rule to semiconductor quantum dots at higher excitation intensity. As the vapor-assisted fabricated CH3NH3PbBr3 perovskite film is a cluster of nanoparticles forming a dense film, it facilitates mobile charge migration between the nanoparticles and charge accumulation at the surface or at the boundary of the nanoparticles. This leads to enhanced Auger-like nonradiative recombination contributing to the fluorescence intermittency observed. This finding provides unique insight into the charge accumulation and migration and thus is of crucial importance for device design and improvement.

The first demonstration of entirely roll-to-roll fabricated perovskite solar cell modules under ambient room conditions.

The rapid development of organic-inorganic hybrid perovskite solar cells has resulted in laboratory-scale devices having power conversion efficiencies that are competitive with commercialised technologies. However, hybrid perovskite solar cells are yet to make an impact beyond the research community, with translation to large-area devices fabricated by industry-relevant manufacturing methods remaining a critical challenge. Here we report the first demonstration of hybrid perovskite solar cell modules, comprising serially-interconnected cells, produced entirely using industrial roll-to-roll printing tools under ambient room conditions. As part of this development, costly vacuum-deposited metal electrodes are replaced with printed carbon electrodes. A high-throughput experiment involving the analysis of batches of 1600 cells produced using 20 parameter combinations enabled rapid optimisation over a large parameter space. The optimised roll-to-roll fabricated hybrid perovskite solar cells show power conversion efficiencies of up to 15.5% for individual small-area cells and 11.0% for serially-interconnected cells in large-area modules. Based on the devices produced in this work, a cost of ~0.7 USD W-1 is predicted for a production rate of 1,000,000 m² per year in Australia, with potential for further significant cost reductions.

Piperidine and Pyridine Series Lead-Free Dion-Jacobson Phase Tin Perovskite Single Crystals and Their Applications for Field-Effect Transistors.

Two-dimensional (2D) organic-inorganic metal halide perovskites have gained immense attention as alternatives to three-dimensional (3D) perovskites in recent years. The hydrophobic spacers in the layered structure of 2D perovskites make them more moisture-resistant than 3D perovskites. Moreover, they exhibit unique anisotropic electrical transport properties due to a structural confinement effect. In this study, four lead-free Dion-Jacobson (DJ) Sn-based phase perovskite single crystals, 3AMPSnI4, 4AMPSnI4, 3AMPYSnI4, and 4AMPYSnI4 [AMP = (aminomethyl)-piperidinium, AMPY = (aminomethyl)pyridinium] are reported. Results reveal structural differences between them impacting the resulting optical properties. Namely, higher octahedron distortion results in a higher absorption edge. Density functional theory (DFT) is also performed to determine the trends in energy band diagrams, exciton binding energies, and formation energies due to structural differences among the four single crystals. Finally, a field-effect transistor (FET) based on 4AMPSnI4 is demonstrated with a respectable hole mobility of 0.57 cm2 V-1 s-1 requiring a low threshold voltage of only -2.5 V at a drain voltage of -40 V. To the best of our knowledge, this is the third DJ-phase perovskite FET reported to date.

Recent progress in layered metal halide perovskites for solar cells, photodetectors, and field-effect transistors.

Metal halide perovskite materials demonstrate immense potential for photovoltaic and electronic applications. In particular, two-dimensional (2D) layered metal halide perovskites have advantages over their 3D counterparts in optoelectronic applications due to their outstanding stability, structural flexibility with a tunable bandgap, and electronic confinement effect. This review article first analyzes the crystallography of different 2D perovskite phases [the Ruddlesden-Popper (RP) phase, the Dion-Jacobson (DJ) phase, and the alternating cations in the interlayer space (ACI) phase] at the molecular level and compares their common electronic properties, such as out-of-plane conductivity, crucial to vertical devices. This paper then critically reviews the recent development of optoelectronic devices, namely solar cells, photodetectors and field effect transistors, based on layered 2D perovskite materials and points out their limitations and potential compared to their 3D counterparts. It also identifies the important application-specific future research directions for different optoelectronic devices providing a comprehensive view guiding new research directions in this field.

Homologous Bromides Treatment for Improving the Open-Circuit Voltage of Perovskite Solar Cells.

The power conversion efficiency (PCE) of solution-processed organic-inorganic mixed halide perovskite solar cells has achieved rapid improvement. However, it is imperative to minimize the voltage deficit (Woc  = Eg /q - Voc ) for their PCE to approach the theoretical limit. Herein, the strategy of depositing homologous bromide salts on the perovskite surface to achieve a surface and bulk passivation for the fabrication of solar cells with high open-circuit voltage is reported. Distinct from the conclusions given by previous works, that homologous bromides such as FABr only react with PbI2 to form a large-bandgap perovskite layer on top of the original perovskite, this work shows that the bromide also penetrates the perovskite film and passivates the perovskite in the bulk. This is confirmed by the small-bandgap enlargement observed by absorbance and photoluminescence, and the bromide element ratio increasing in the bulk by time-of-flight secondary-ion mass spectrometry and depth-resolved X-ray photoelectron spectroscopy. Furthermore, a clear suppression of non-radiative recombination is confirmed by a variety of characterization methods. This work provides a simple and universal way to reduce the Woc of single-junction perovskite solar cells and it will also shed light on developing other high-performance optoelectronic devices, including perovskite-based tandems and light-emitting diodes.

Thermal-Radiation-Driven Ultrafast Crystallization of Perovskite Films Under Heavy Humidity for Efficient Inverted Solar Cells.

Fabricating perovskite solar cells (PSCs) in air is conducive to low-cost commercial production; nevertheless, it is rather difficult to achieve comparable device performance as that in an inert atmosphere because of the poor moisture toleration of perovskite materials. Here, the perovskite crystallization process is systematically studied using two-step sequential solution deposition in an inert atmosphere (glovebox) and air. It is found that moisture can stabilize solvation intermediates and prevent their conversion into perovskite crystals. To address this issue, thermal radiation is used to accelerate perovskite crystallization for integrated perovskite films within 10 s in air. The as-formed perovskite films are compact, highly oriented with giant grain size, superior photoelectric properties, and low trap density. When the films are applied to PSC devices, a champion power conversion efficiency (PCE) of 20.8% is obtained, one of the best results for air-processed inverted PSCs under high relative humidity (60 ± 10%). This work substantially assists understanding and modulation to perovskite crystallization kinetics under heavy humidity. Also, the ultrafast conversion strategy by thermal radiation provides unprecedented opportunities to manufacture high-quality perovskite films for low-temperature, eco-friendly, and air-processed efficient inverted PSCs.

Inorganic-Cation Pseudohalide 2D Cs2 Pb(SCN)2 Br2 Perovskite Single Crystal.

Most of the reported 2D Ruddlesden-Popper (RP) lead halide perovskites with the general formula of An +1 Bn X3 n +1 (n = 1, 2, …) comprise layered perovskites separated by A-site-substituted organic spacers. To date, only a small number of X-site-substituted RP perovskites have been reported. Herein, the first inorganic-cation pseudohalide 2D phase perovskite single crystal, Cs2 Pb(SCN)2 Br2 , is reported. It is synthesized by the antisolvent vapor-assisted crystallization (AVC) method at room temperature. It exhibits a standard single-layer (n = 1) Ruddlesden-Popper structure described in space group of Pmmn (#59) and has a small separation (d = 1.69 Å) between the perovskite layers. The SCN- anions are found to bend the 2D Pb(SCN)2 Br2 framework slightly into a kite-shaped octahedron, limiting the formation of a quasi-2D perovskite structure (n > 1). This 2D single crystal exhibits a reversible first-order phase transformation to 3D CsPbBr3 (Pm3m #221) at 450 K. It has a low exciton binding energy of 160 meV-one of the lowest for 2D perovskites (n = 1). A Cs2 Pb(SCN)2 Br2 -single-crystal photodetector is demonstrated with respectable responsivity of 8.46 mA W-1 and detectivity of ≈1.2 × 1010 Jones at a low bias voltage of 0.5 V.

Immediate and Temporal Enhancement of Power Conversion Efficiency in Surface-Passivated Perovskite Solar Cells.

This work reports strategies for improving the power conversion efficiency (PCE) by capitalizing on temporal changes through the storage effect and immediate improvements by interface passivation. It is demonstrated that both strategies can be combined as shown by PCE improvement in passivated perovskite solar cells (PSCs) upon ambient storage because of trap density reduction. By analyzing the dominant charge recombination process, we find that lead-related traps in perovskite bulk, rather than at the surface, are the recombination centers in both as-fabricated and ambient-stored passivated PSCs. This emphasizes the necessity to reduce intrinsic defects in the perovskite bulk. Furthermore, storage causes temporal changes in band alignment even in passivated PSCs, contributing to PCE improvement. Building on these findings, composition engineering was employed to produce further immediate PCE improvements because of defect reduction in the bulk, achieving a PCE of 22.2%. These results show that understanding the dominant recombination mechanisms within a PSC is important to inform strategies for producing immediate and temporal PCE enhancements either by interface passivation, storage, composition engineering, or a combination of them all to fabricate highly efficient PSCs.

Flexible and efficient perovskite quantum dot solar cells via hybrid interfacial architecture.

All-inorganic CsPbI3 perovskite quantum dots have received substantial research interest for photovoltaic applications because of higher efficiency compared to solar cells using other quantum dots materials and the various exciting properties that perovskites have to offer. These quantum dot devices also exhibit good mechanical stability amongst various thin-film photovoltaic technologies. We demonstrate higher mechanical endurance of quantum dot films compared to bulk thin film and highlight the importance of further research on high-performance and flexible optoelectronic devices using nanoscale grains as an advantage. Specifically, we develop a hybrid interfacial architecture consisting of CsPbI3 quantum dot/PCBM heterojunction, enabling an energy cascade for efficient charge transfer and mechanical adhesion. The champion CsPbI3 quantum dot solar cell has an efficiency of 15.1% (stabilized power output of 14.61%), which is among the highest report to date. Building on this strategy, we further demonstrate a highest efficiency of 12.3% in flexible quantum dot photovoltaics.

Visualizing the Impact of Light Soaking on Morphological Domains in an Operational Cesium Lead Halide Perovskite Solar Cell.

The dynamics of photogenerated carriers and mobile ions in operational cesium lead halide (CsPbI3) perovskite solar cells (PSCs) under working conditions are studied using nanoscale-resolved fluorescence lifetime imaging microscopy (FLIM). The temporally and spatially resolved photoluminescence (PL) changes in the perovskite film during and after bias light soaking are dynamically monitored. Through the analysis of the dynamic variations of PL intensity and PL lifetime of an open-circuit PSC, the impacts of light soaking are revealed by a dynamic model of photogenerated charge carrier and mobile ions. We confirmed the different behaviors between morphological domain interiors and domain boundaries during light soaking, which shed light on the engineering of the domain interiors in addition to the commonly considered domain boundary strategies. This work provides a full picture of the photogenerated process in an operational PSC and therefore guides the design and operation of perovskite-based optoelectronic devices.