RESUMEN
Our main focus is to explore the atomic electronegativity-dependent photoinduced behavior of styryl derivatives (HBO, HBS, and HBSe). The results of structural parameter calculation by the DFT method show that the intramolecular hydrogen bonds of normal and tautomer form are strengthened and weakened, respectively, in an excited state (S1), which is conducive to the excited intramolecular proton transfer (ESIPT) process. The enhancement of excited hydrogen bond is beneficial to the ESIPT process from the aspects of infrared vibration frequency (IR), Mulliken's charge analysis, and density gradient reduction (RDG). Additionally, by determining the bond energy with the band critical point (BCP) parameter, we found that the lower the electronegativity of the atom, the larger the hydrogen bond strength at the excited state and the more likely ESIPT reaction occurs. Meanwhile, the intramolecular H-bonds O-H N in HBO, HBS, and HBSe are enhanced with the weakened electron-withdrawing capacity of the atom (from O to S and Se). Subsequently, frontier molecular orbital (FMOs) and charge density difference (CDD) analyses essentially revealed that electron redistribution induces the ESIPT process. Low atomic electronegativity exhibits the high chemical activity of the excited state. Furthermore, to demonstrate the electronegativity-dependent ESIPT behavior of the system, we built potential energy curves (PECs) and located the transition states (TS) of proton transfer processes.
RESUMEN
To obtain atomic-level insights into the decomposition behavior of 1,3,5-trinitro-2,4,6-trinitroaminobenzene (TNTNB) under different stimulations, this study applied reactive molecular dynamics simulations to illustrate the effects of thermal and shock stimuli on the TNTNB crystal. The results show that the initial decomposition of the TNTNB crystal under both thermal and shock stimuli starts with the breakage of the N-NO2 bond. However, the C6 ring in TNTNB undergoes structural rearrangement to form a C3-C5 bicyclic structure at a constant high temperature. Then, the C3 and C5 rings break in turn. The main final products of TNTNB under shock are N2, CO2, and H2O, while NO, N2, H2O and CO are formed instead at 1 atm under a constant high temperature. Pressure is the main reason for this difference. High pressure promotes the complete oxidation of the reactants.
RESUMEN
We developed a new coarse-grained (CG) molecular dynamics force field for polyacrylamide (PAM) polymer based on fitting to the quantum mechanics (QM) equation of state (EOS). In this method, all nonbond interactions between representative beads are parameterized using a series of QM-EOS, which significantly improves the accuracy in comparison to common CG methods derived from atomistic molecular dynamics. This CG force-field has both higher accuracy and improved computational efficiency with respect to the OPLS atomistic force field. The nonbond components of the EOS were obtained from cold-compression curves on PAM crystals with rigid chains, while the covalent terms that contribute to the EOS were obtained using relaxed chains. For describing PAM gels we developed water-PAM interaction parameters using the same method. We demonstrate that the new CG-PAM force field reproduces the EOS of PAM crystals, isolated PAM chains, and water-PAM systems, while successfully predicting such experimental quantities as density, specific heat capacity, thermal conductivity and melting point.
RESUMEN
Metal nanoparticles are easily deactivated by migration-aggregation in combustion. Encapsulated nanoparticles are one of the tools for coping with the stability challenges of metal nanoparticles. The self-assembly details of aluminum nanoparticles (ANPs) encapsulated into carbon nanotubes (CNTs) were demonstrated by molecular dynamics simulations. The simulation results show that ANPs can completely self-roll into CNTs to form a stable core-shell structure by inertial force and van der Waals force. Inside the tubes, ANPs move toward the cap at a velocity of 2.27 Å ps-1. However, it increases to 3.17 Å ps-1 when near the cap of CNTs. The initiation of the ANPs' oxidation and degradation can be effectively checked by coating CNTs. The diffusion of the Al atoms in the encapsulated ANPs occurred earlier than their oxidation in combustion, verified by using ReaxFF molecular dynamics simulations. The morphological evolutions of the nanostructures in the initial combustion of the encapsulated ANPs are predicted. The interplay between the encapsulated ANPs' responses and external stimuli is classified into core-shell separation, shell damage, and core-shell burst, which provides insights into the oxidation mechanism of encapsulated nanoparticles.
RESUMEN
Energetic salts based on pentazolate anion (cyclo-N5-) have attracted much attention due to their high nitrogen contents. However, it is an enormous challenge to efficiently screen out an appropriate cation that can match well with cyclo-N5-. The vertical electron affinity (VEA) of the cations and vertical ionization potential (VIP) of the anions for 135 energetic salts and some cyclo-N5- salts were calculated by the density functional theory (DFT). The magnitudes of VEA and VIP, and their matchability were analyzed. The results based on the calculations at the B3LYP/6-311++G(d,p) and B3LYP/aug-cc-pVTZ levels indicate that there is an excellent compatibility between cyclo-N5- and cation when the difference between the VEA of cation and the VIP of cyclo-N5- anion is -2.8 to -1.0 eV. The densities of the salts were predicted by the DFT method. Relationship between the calculated density and the experimental density was established as ρExpt = 1.111ρcal - 0.06067 with a correlation coefficient of 0.905. This regression equation could be in turn used to calibrate the calculated density of the cyclo-N5- energetic salts accurately. This work provides a favorable way to explore the energetic salts with excellent performance based on cyclo-N5-.
Asunto(s)
Aniones/química , Nitrógeno/química , Sales (Química)/química , Cationes/química , Química Computacional , Gravedad Específica , Temperatura , TermodinámicaRESUMEN
On the basis of thieno(3,2-b)thiophene and dithieno[3,2-b:2',3'-d]thiophene (T2 and T3 moieties) as π-linker, the A, D and S series dyes were designed to investigate the effect of the introducing N+ as an "electron trap" into T2 and T3 on the properties of the dyes. The optimized structures, electronic and optical properties were investigated by the density functional theory (DFT) and time-dependent DFT (TD-DFT). The results show that the properties of the dyes are sensitive to the N+ position in π-linkers. D series dyes with electron-withdrawing units located near the donor have better properties than the corresponding A series with the electron-withdrawing units located near the acceptor. For A and D series, the N+ modified dye named T2N+1-d displays the largest red shift of the UV-vis absorption, the maximum integral values of the adsorption-wavelength curves over the visible light, the highest light harvesting efficiency (LHE, 0.996), and the strongest adsorption energy (-44.33 kcal/mol). T2N+1-d also has a large driving force of hole injection (ΔGinj, -0.74 eV), which results in a more efficient hole injection. Bearing a lengthier π-linker than T2N+1-d, the properties of T2N+1-s are further improved. T2N+1-d moiety or its increased conjugated derivatives may be a promising π-linker.
Asunto(s)
Colorantes/química , Nitrógeno/química , Fármacos Fotosensibilizantes/química , Teoría Funcional de la Densidad , Estructura MolecularRESUMEN
Molecular dynamic simulation of a high explosive, RDX, mixed with AlH3 nanoparticles was performed by a newly parameterized ReaxFF force field. Testing of the ReaxFF shows that the mean absolute errors of the densities and bond lengths between calculated and experimental values are less than 7% and 3%, respectively. Using the ReaxFF, effects of AlH3 nanoparticles with different radii on the thermal decomposition of RDX were revealed. A new mechanism of the generation and the consumption of H2 was discovered in the explosion. The H2 is released by AlH3 firstly and then it reacts with NO2 and CO2 from the decomposition of RDX, leading to an increase of H2O, NO and CO. Meanwhile, the size effect of AlH3 upon the reaction was also revealed. As a result, the number of produced H2O and CO2 molecules increases by 10.38% and 56.85%, respectively, when the radius of AlH3 nanoparticles decreases from 1.10 to 0.68 nm. This showed that RDX decomposes more completely with smaller AlH3 nanoparticles, which was further demonstrated by the analysis of reaction residues and diffusion coefficients.
RESUMEN
Aluminized explosives have important applications in civil construction and military armaments, but their thermal decomposition mechanisms are not well characterized. Here, the thermal decomposition of TNT, RDX, HMX and CL-20 on Al nanoparticles is examined by reactive dynamics simulations using a newly parameterized reactive force field with low gradient correction (ReaxFF-lg). Partially passivated Al nanoparticles were constructed and mixed with TNT, RDX, HMX and CL-20 crystals and then the mixed systems are heated to a high temperature in which the explosives are fully decomposed. The simulation results show that the aluminized explosives undergo three main steps of thermal decomposition, which were denoted "adsorption period" (0-20 ps), "diffusion period" (20-80 ps) and "formation period" (80-210 ps). These stages in sequence are the chemical adsorption between Al and surrounding explosive molecules (R-NO2-Al bonding), the decomposition of the explosives and the diffusion of O atoms into the Al nanoparticles, and the formation of final products. In the first stage, the Al nanoparticles decrease the decomposition reaction barriers of RDX (1.90 kJ g-1), HMX (1.95 kJ g-1) and CL-20 (1.18 kJ g-1), respectively, and decrease the decomposition reaction barrier of TNT from 2.99 to 0.29 kJ g-1. Comparing with the crystalline RDX, HMX and CL-20, the energy releases are increased by 4.73-4.96 kJ g-1 in the second stage. The number of produced H2O molecules increased by 25.27-27.81% and the number of CO2 molecules decreased by 47.73-68.01% in the third stage. These three stages are further confirmed by the evolutive diagram of the structure and temperature distribution for the CL-20/Al system. The onset temperatures (To) of generating H2O for all the aluminized explosives decrease, while those of generating CO2 for aluminized HMX and CL-20 increase, which are in accord with the experiment of aluminized RDX.
RESUMEN
An analogue-oriented synthetic route for the formulation of furazan-functionalized 5-nitroimino-1,2,4-triazoles has been explored. The process was found to be straightforward, high yielding, and highly efficient, and scalable. Nine compounds were synthesized and the physicochemical and energetic properties, including density, thermal stability, and sensitivity, were investigated, as well as the energetic performance (e.g., detonation velocities and detonation pressures) as evaluated by using EXPLO5 code. Among the new materials, compounds 4-6 and 11 possess high densities, acceptable sensitivities, and good detonation performances, and thereby demonstrate the potential applications as new secondary explosives.
RESUMEN
Two new D-π-A zinc porphyrin dyes with thiophene and furan π-bridges have been synthesized and employed in dye-sensitized solar cells (DSSCs). Here, the triphenylamine (TPA) moiety was used as the electron donor, and the hexylthiophene chromophores were introduced onto the donor groups, which effectively extended the π-conjugation system. Although the two dyes had similar molecular structures, there was a significant difference between their optical and photoelectric properties. The EIS analysis suggested that the dye with the thiophene π-bridge had a lower charge recombination rate compared to the dye with the furan π-bridge. Based on their light-harvesting abilities, the power conversion efficiency (PCE) of dye JP-S was higher than that of dye JP-O. The JP-S-based DSSC showed a PCE of 5.84%, whereas the PCE of the JP-O-based DSSC was 4.68%. Moreover, using the dye TTR1 as a co-sensitizer made up for the poor absorption of porphyrin dyes in the 480-600 nm range and reduced the charge recombination. The JP-S + TTR1-based DSSCs showed a higher PCE of 6.71%, and the Jsc and Voc values of the device were both increased using this strategy.
RESUMEN
Eight molecular structures (BT-A1 to BT-A8) with high-performance non-fullerene acceptor (NFA) were selected for organic solar cells (OSCs) and non-linear optical (NLO) applications. Their electronic, photovoltaic (PV) and optoelectronic properties were tuned by adding powerful electron-withdrawing groups to the acceptor (A) of the D-π-A-π-D structure. Using time-dependent density functional theory (TD-DFT) techniques, based on the laws of quantum chemical calculations, the absorption spectra, stability of the highest and lowest-energy molecular orbitals (HOMO/LUMOs), electron density, intramolecular charge transfer (ICT), transition density matrix (TDM), were examined. The binding energy (Eb) and density of states (DOS) were probed to realize the optoelectronic analysis of the structures BT-A1 to BT-A8. Noncovalent interactions (NCIs) based on a reduced density gradient (RDG) were used to describe the nature and strength of D-A interactions in the molecules BT-A1 to BT-A8. The new refined molecules BT-A1 to BT-A8 exhibited strong absorbance bands between 408-721 nm and high electron transfer contribution (ETC) ranges between 87-96 %, along with the smallest excitation energies (Ex) between 1.71-3.55 eV in the solvent dichloromethane. Dipolar moment strengths ranging from 0.38 to 4.72 Debye in both the excited and ground states have determined with good solubility properties of BT-A1 to BT-A8 in polar solvent. Highly effective charge mobilities and prevention of charge recombination have been demonstrated by the electron (0.18-0.41 eV) and hole RE values (0.13-0.89 eV) for the new compounds. Power conversion efficiencies (PCE) of BT-A1 to BT-A8 were nearly the same because of better outcomes compared to the molecules in the BT. Compared to poly[4.8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b: 4,5-b']dithiophene-2,6- diyl-alt-(4-2-ethylhexyl)-3-fluorothieno[3,4-b]thiophene-)-2-carboxylate-2-6-diyl)] (PTB7-Th), the open circuit voltages (Voc) of compounds BT-A1 to BT-A8 were ranged from 1.52 to 2.13 eV. The polarizability (α) and hyperpolarizability (ß) of the molecules BT-A1 to BT-A8 were used to determine the non-linear optical (NLO) properties. The results showed that BT-A2, BT-A6 and BT-A7 have good NLO activity. This computational analysis demonstrates the superiority of the molecules with NFA. Hence the compounds are advised for the use in production of high-performance OSCs and NLO activity.
RESUMEN
The excited (S1) state charge distribution characteristics and fluorescence mechanism of fluorescence probes benzyl (6-cyano-2-naphthoyl)-L-valinate (NPI) and benzyl (6-amino-2-naphthoyl)-L-valinate (NPA) have been discussed using density functional theory (DFT) and time-dependent density functional theory (TD-DFT). Further analysis by constructing a torsional potential energy curve (PEC) shows that a well-defined minimum energy conformation is observed when the C-C single bond between the valine benzyl ester and naphthalene ring in NPI rotates. For NPA, the most stable conformation is the naphthalene ring conformation with dihedral angle N2C1C2C3 of -30.60°, whose total energy is 0.17 kcal/mol lower than that of the second most stable conformer. The frontier molecular orbitals (FMOs) demonstrate that NPI exhibits a low degree of charge coupling, and the oscillator intensity is close to zero, indicating that it is not conducive to luminescence. However, in the S1 state, the oscillator strength of NPA is 1.2044, which is a bright state, resulting in the strong emitting. Additionally, fluorescence imaging is favored as a visual observation technique, and Stokes shift is an important physical parameter to measure fluorescence. According to the idea that changing the number and position of functional groups can affect the photophysical properties of fluorescent dyes, o-NPDI, p-NPDI and m-NPDI dyes were newly designed and o-NPDA, p-NPDA, m-NPDA produced after recognition of Hg2+. The spectral performance results show that the newly designed fluorescent dye (p-NPDA) can not only emit in the near infrared region after recognizing Hg2+, but also has a large Stokes shift (236 nm). This indirectly reflects that para-substitution is more conducive to Stokes shift, and has become one of the strategies for fluorescent dye design.
RESUMEN
Fast and real-time detection of trace Hg(â ¡) by fluorescent probes under acidic conditions is urgently required due to the high toxicity and accessibility to creatures and human being. However, fluorescent probes for Hg(â ¡) detection in environmental samples are rarely reported due to the protonation potential of acidic mercury sources. In this study, the SD probe was developed by 5-(p-dimethylaminobenzylidene) rhodanine (DMABR) loaded on sepiolite by hydrothermal treatment, and showed excellent Hg(â ¡) detection performances for mercury sources at pH 4-10 due to buffering ability of the hyperconjugated lactam rings. Sepiolite functioned as the support skeleton to decrease intermolecular transition, and thus increased the sensitivity. At pH 4, the SD probe showed high selectivity and sensitivity for Hg(â ¡) among various species, with low LOD and binding constant of 4.78 × 10-9 M and 1.34 × 106 M-1, respectively. Through DFT calculations, MAS 1H NMR and 2D-COS analysis, the detection mechanism was demonstrated as SN1 substitution of the spontaneous leaving H on amino groups in the transient state during tautomeric equilibrium, rather than the expected high-affinity sulphydryl. Additionally, the SD probe exhibited promising potential in quantifying water-soluble and bioavailable Hg(â ¡) in acidic polluted soil and water samples. Moreover, real-time detection was realized by paper-based strips.
RESUMEN
Dye-sensitized solar cells (DSSCs) are currently under intense academic and industrial investigations, because of their environmentally-friendly, efficient, and low-cost features. The photosensitizer plays a key role in determining DSSCs' performance. The 4,4'-di(2-thienyl)triphenylamine moiety, included in dye TTC102, has been demonstrated before as a novel and efficient electron donor fragment. In this paper, the oversimple π-conjugated bridge of TTC102 was replaced by a 9-ethyl-3,6-di(2-thiophenyl)carbazole moiety. Two new D-D-π-A sensitizers, named TTC104 and TTC105, were synthesized and fully characterized. After anchoring on TiO(2) nanoparticle film, the absorption band of TTC104 is broader by 30 nm than that of TTC102. Under AM 1.5G irradiation, the energy conversion efficiency (η) of a DSSC based on TTC104 reaches 6.36%, which is 21.6% higher than that of TTC102 (5.24%). The results above demonstrate that the photovoltaic performance can be improved after introducing the 9-ethyl-3,6-di(2-thiophenyl)carbazole moiety to TTC102 when employed in DSSCs. Dye TTC105, containing a pyridyl group as the electron acceptor, showed only 1.88% conversion efficiency (η) when used in DSSCs. The huge different performances of TTC104 and TTC105 are proved to be partly due to the smaller dye loading amount, higher dark current and charge recombination rate of TTC105.
RESUMEN
The adsorption and reaction of H2O molecule on neutral X-centered icosahedronal Al12X clusters (X = Al, Mg, Zn, Ga, Ni, Fe, B, C, Si, P) were investigated by PW91, PBE, and PWC methods. Reaction energies and reaction barriers were determined. The spin states and the doped atoms have important influences on the Al12X geometries, density, electronic properties, and energy density of reaction between Al12X with a single H2O molecule. The energies of the neutral X-centered Al12X are lower than that of surface X-replaced Al12X with the exception of Al12Mg. The H2O dissociation on the Al12X (X = Mg, Zn, Ga, Ni, Fe) clusters have relatively low activation barriers, but large activation barriers for Al12X (X = B, C, Si, P). The activation barrier of water dissociation on the singlet Al12Fe cluster is the lowest, whereas the highest barrier is with the Al12C. The reaction of H2O with Al12Fe is the most exothermic. The center-Fe atom can move out to the surface after the adsorption and dissociation of H2O with an energy barrier of 172 kJ/mol. The results showed that the water dissociation on the Al12X cluster can be tuned by controllable X doping.
RESUMEN
The adsorption of a CO2 molecule on neutral and charged X-centered icosahedron Al12X(±z) clusters (X = Al, Be, Zn, Ni, Cu, B, P; z = 0, 1) was investigated by the density functional PW91 and PWC methods. Optimized configurations corresponding to physisorption and chemisorption of CO2 were identified. The adsorption energies, activation barriers, and binding energies involving both the physisorption (Al12X(±z)·CO2-I) and chemisorption (Al12X(±z)·CO2-II) for CO2 were determined. The chemisorption of a CO2 molecule on the Al12X clusters (X is a metallic doping element) requires relatively low activation barriers. The lowest barrier was found to be with the Al12Be cluster. For the Al12X(-) clusters, the barriers are all higher than those of the neutral analogues. For the Al12X(+) clusters, two corresponding configurations are linked by a low-energy barrier, and CO2 molecule chemisorption on the Al12Be(+) cluster has the lowest barrier. The adsorption energies are larger than the energy barriers, which facilitates the chemisorption. The results show that carbon dioxide adsorbed on the Al12X(±z) clusters can be tuned by controllable X doping and the total number of valence electrons and suggest the potential application of Al12X(±z) nanostructures for carbon dioxide capture and activation.
RESUMEN
CONTEXT: The morphologies of hexanitrohexaazaisowurtzitane (CL-20) and 1,4-dinitroimidazole (1,4-DNI) co-crystal under vacuum or solvent at different temperatures were predicted. The CL-20/1,4-DNI co-crystal has six important growth crystal planes: (002), (011), (101), (11â1), (110), (111). The areas of (002), (101), and (011) planes account for a relatively large proportion, which are important crystal planes that affect the crystal morphology. The crystal habits at different temperatures were simulated. The simulation results showed that the crystal plane attachment energy of CL-20 and 1,4-DNI co-crystal increases with the increase of temperature, indicating that the increase of temperature is conducive to the growth of crystal planes. The aspect ratio decreases with the increase of temperature and the morphology of co-crystal becomes more spherical at a higher temperature. The theoretical predictions are in good agreement with the experiment. The simulation results can provide guidance for the crystallization of CL-20/1,4-DNI to obtain a nearly spherical crystal morphology. METHODS: The CL-20/1,4-DNI unit cell structure was geometrically optimized by the COMPASS force field. The AE model was used to predict the morphology of CL-20/1,4-DNI under vacuum, resulting in the most morphologically important growth planes. Ethyl acetate was selected as the solvent. The interaction energy between the solvent and the crystal plane, and the attachment energies in solvent at 298 K, 320 K, 340 K, 360 K, and 380 K were predicted. The NVT ensemble is used in the molecular dynamics calculation process. The simulation step is 1 fs and the total simulation time is 500 ps. The Andersen thermostat is selected as the temperature control method. In the potential energy calculation, the atom-based and Ewald methods were selected to calculate the van der Waals force and the electrostatic interaction force, respectively.
RESUMEN
Lack of experience concerning the organic conversion period and its associated challenges have made it difficult for conventional farmers to convert to organic farming. In this study, using a combined life cycle assessment (LCA) with data envelopment analysis (DEA) approach, we investigated farming management strategies, and environmental, economic, and efficiency impacts of organic conversion tea farms (OCTF, N = 15) compared to conventional (CTF, N = 13) and organic (OTF, N = 14) tea farms in Wuyi County, China for a year-round (2019). We found that the OCTF reduced agricultural inputs (environmental impacts) and applied more manual harvesting (increased added value) to pull through the conversion period. According to the LCA results, OCTF showed a similar integrated environmental impact index compared with OTF but significantly (P < 0.05) lower than CTF at both midpoint and endpoint levels. In terms of economic assessment, OTF showed the significantly highest total revenue (18.7 thousand $ ha-1 yr-1) and profit (13.7 thousand $ ha-1 yr-1) (P < 0.05) among the farm types. In contrast, OCTF and CTF did not show significant differences in relation to these economic indicators (P > 0.05). The total cost and cost-profit ratio did not show significant differences among the three farm types. Considering the DEA analysis, there were no significant differences in the technical efficiency of all farm types. However, the eco-efficiency of OCTF and OTF was significantly higher than that of CTF. Therefore, conventional tea farms can survive the conversion period with competitive economic and environmental benefits. In this regard, policies should promote organic tea cultivation and agroecological practices to enhance the sustainable transformation of tea production systems.
Asunto(s)
Industria Lechera , Agricultura Orgánica , Granjas , Industria Lechera/métodos , Ambiente , Agricultura/métodos , China , TéRESUMEN
CONTEXT: The development of high-efficiency photovoltaic devices is the need of time with increasing demand for energy. Herein, we designed seven small molecule donors (SMDs) with A-π-D-π-A backbones containing various acceptor groups for high-efficiency organic solar cells (OSCs). Molecular engineering was performed by substituting the acceptor group in the synthesized compound (BPR) with another highly efficient acceptor group to improve the photoelectric performance of the molecule. METHOD: The photovoltaic, optoelectronic, and photophysical properties of the proposed compounds (BP1-BP7) were investigated in comparison to BPR using DFT and TD-DFT at MPW1PW91/6-311G(d,p) level of theory. All molecules we designed have red-shifted absorption spectra. The modification of the acceptor fragment of the BPR resulted in a reduced HOMO-LUMO energy gap; thus, the designed compounds (BP1-BP7) had improved optoelectronic responses as compared with the BPR molecule. Various key factors that are crucial for efficient SMDs such as exciton binding energy, frontier molecular orbitals (FMOs), absorption maximum (λmax), open circuit voltage (VOC), dipole moment (µ), excitation charge mobilities, and the transition density matrix of (BPR, BP1-BP7) have also been studied. Low reorganizational energy (holes and electrons) values provide high charge mobility, and all the designed compounds are efficient in this regard. Here, BP6 exhibits low excitation energy (1.66 eV), highest open circuit voltage (2.00 V), normalized VOC (77.23), and fill factor (0.931). Consequently, the superiority of the designed molecules advises experimenters to envision future developments in extremely effective OSC devices.
RESUMEN
Flumequine (FLU) and nadifloxacin (NAD), as emerging contaminants, have received extensive attention recently. In this study, a triazine-based microporous organic network (TMON) was synthetized and developed as an excellent adsorbent for FLU and NAD. The adsorption behavior and influence factors were investigated in both single and binary systems. Insight into the adsorption mechanisms were conducted through experiments, models, and computational studies, from macro and micro perspectives including functional groups, adsorption sites, adsorption energy and frontier molecular orbital. The results showed that the maximum adsorption capacities of TMON for FLU and NAD are 325.27 and 302.28 mg/g under 30 °C higher than records reported before. TMON exhibits the better adaptability and anti-interference ability for influence factors, leading to the preferable application effect in kinds of real water samples. TMON also shows the application potentials for the adsorption of other quinolone antibiotics and CO2 capture. Hydrogen-bonding interaction played the most critical role compared to π-π stacking effect, π-π electron-donor-acceptor interaction, CH-π interaction, and hydrophobic interaction during the adsorption. TMON could be regarded as a promising environmental adsorbent for its large surface area, stable physical and chemical properties, excellent recyclability, and wide range of applications.