A disordered rock salt anode for fast-charging lithium-ion batteries.

Rechargeable lithium-ion batteries with high energy density that can be safely charged and discharged at high rates are desirable for electrified transportation and other applications1-3. However, the sub-optimal intercalation potentials of current anodes result in a trade-off between energy density, power and safety. Here we report that disordered rock salt4,5 Li3+xV2O5 can be used as a fast-charging anode that can reversibly cycle two lithium ions at an average voltage of about 0.6 volts versus a Li/Li+ reference electrode. The increased potential compared to graphite6,7 reduces the likelihood of lithium metal plating if proper charging controls are used, alleviating a major safety concern (short-circuiting related to Li dendrite growth). In addition, a lithium-ion battery with a disordered rock salt Li3V2O5 anode yields a cell voltage much higher than does a battery using a commercial fast-charging lithium titanate anode or other intercalation anode candidates (Li3VO4 and LiV0.5Ti0.5S2)8,9. Further, disordered rock salt Li3V2O5 can perform over 1,000 charge-discharge cycles with negligible capacity decay and exhibits exceptional rate capability, delivering over 40 per cent of its capacity in 20 seconds. We attribute the low voltage and high rate capability of disordered rock salt Li3V2O5 to a redistributive lithium intercalation mechanism with low energy barriers revealed via ab initio calculations. This low-potential, high-rate intercalation reaction can be used to identify other metal oxide anodes for fast-charging, long-life lithium-ion batteries.

Solar Desalination Using Thermally Responsive Ionic Liquids Regenerated with a Photonic Heater.

Growing global water demand has brought desalination technologies to the forefront for freshwater production from nontraditional water sources. Among these, forward osmosis (FO) is a promising two-step desalination process (draw dilution and regeneration), but it is often overlooked due to the energy requirements associated with draw regeneration. To address this limiting factor, we demonstrate FO desalination using thermally responsive ionic liquids (ILs) that are regenerated using a renewable energy input, that is, solar heat. To efficiently harness sunlight, a simple photonic heater converts incoming irradiation into infrared wavelengths that are directly absorbed by IL-water mixtures, thereby inducing phase separation to yield clean water. This approach is markedly different as it uses radiative heating, a noncontact mode of heat transfer that couples to chemical functional groups within the IL for rapid energy transfer without a heat exchanger or secondary fluid. Overall, a solar-thermal separation efficiency of 50% is achieved under unconcentrated sunlight, which can be increased to 69% with the thermal design. Successful desalination of produced water from oil wells in Southern California highlights the potential of solar-powered IL-FO for energy-efficient and low-cost desalination of complex brines for beneficial water reuse.

In Situ ATR-SEIRAS of Carbon Dioxide Reduction at a Plasmonic Silver Cathode.

Illumination of a voltage-biased plasmonic Ag cathode during CO2 reduction results in a suppression of the H2 evolution reaction while enhancing CO2 reduction. This effect has been shown to be photonic rather than thermal, but the exact plasmonic mechanism is unknown. Here, we conduct an in situ ATR-SEIRAS (attenuated total reflectance-surface-enhanced infrared absorption spectroscopy) study of a sputtered thin film Ag cathode on a Ge ATR crystal in CO2-saturated 0.1 M KHCO3 over a range of potentials under both dark and illuminated (365 nm, 125 mW cm-2) conditions to elucidate the nature of this plasmonic enhancement. We find that the onset potential of CO2 reduction to adsorbed CO on the Ag surface is -0.25 VRHE and is identical in the light and the dark. As the production of gaseous CO is detected in the light near this onset potential but is not observed in the dark until -0.5 VRHE, we conclude that the light must be assisting the desorption of CO from the surface. Furthermore, the HCO3- wavenumber and peak area increase immediately upon illumination, precluding a thermal effect. We propose that the enhanced local electric field that results from the localized surface plasmon resonance (LSPR) is strengthening the HCO3- bond, further increasing the local pH. This would account for the decrease in H2 formation and increase the CO2 reduction products in the light.

Infrared Nanospectroscopy at the Graphene-Electrolyte Interface.

We present a new methodology that enables studies of the molecular structure of graphene-liquid interfaces with nanoscale spatial resolution. It is based on Fourier transform infrared nanospectroscopy (nano-FTIR), where the infrared (IR) field is plasmonically enhanced near the tip apex of an atomic force microscope (AFM). The graphene seals a liquid electrolyte reservoir while acting also as a working electrode. The photon transparency of graphene enables IR spectroscopy studies of its interface with liquids, including water, propylene carbonate, and aqueous ammonium sulfate electrolyte solutions. We illustrate the method by comparing IR spectra obtained by nano-FTIR and attenuated total reflection (which has a detection depth of a few microns) demonstrating that the nano-FTIR method makes it possible to determine changes in speciation and ion concentration in the electric double and diffuse layers as a function of bias.

Kerr gated Raman spectroscopy of LiPF6 salt and LiPF6-based organic carbonate electrolyte for Li-ion batteries.

Fluorescent species are formed during cycling of lithium ion batteries as a result of electrolyte decomposition due to the instability of the non-aqueous electrolytes and side reactions that occur at the electrode surface. The increase in the background fluorescence due to the presence of these components makes it harder to analyse data due to the spectroscopic overlap of Raman scattering and fluorescence. Herein, Kerr gated Raman spectroscopy was shown to be an effective technique for the isolation of the scattering effect from the fluorescence enabling the collection of the Raman spectra of LiPF6 salt and LiPF6-based organic carbonate electrolyte, without the interference of the fluorescence component. Kerr gated Raman was able to identify POF3 on the LiPF6 particle surface, after the addition of trace water.

Dependence on Crystal Size of the Nanoscale Chemical Phase Distribution and Fracture in LixFePO4.

The performance of battery electrode materials is strongly affected by inefficiencies in utilization kinetics and cycle life as well as size effects. Observations of phase transformations in these materials with high chemical and spatial resolution can elucidate the relationship between chemical processes and mechanical degradation. Soft X-ray ptychographic microscopy combined with X-ray absorption spectroscopy and electron microscopy creates a powerful suite of tools that we use to assess the chemical and morphological changes in lithium iron phosphate (LiFePO4) micro- and nanocrystals that occur upon delithiation. All sizes of partly delithiated crystals were found to contain two phases with a complex correlation between crystallographic orientation and phase distribution. However, the lattice mismatch between LiFePO4 and FePO4 led to severe fracturing on microcrystals, whereas no mechanical damage was observed in nanoplates, indicating that mechanics are a principal driver in the outstanding electrode performance of LiFePO4 nanoparticles. These results demonstrate the importance of engineering the active electrode material in next generation electrical energy storage systems, which will achieve theoretical limits of energy density and extended stability. This work establishes soft X-ray ptychographic chemical imaging as an essential tool to build comprehensive relationships between mechanics and chemistry that guide this engineering design.

The formation mechanism of fluorescent metal complexes at the Li(x)Ni(0.5)Mn(1.5)O(4-δ)/carbonate ester electrolyte interface.

Electrochemical oxidation of carbonate esters at the Li(x)Ni(0.5)Mn(1.5)O(4-δ)/electrolyte interface results in Ni/Mn dissolution and surface film formation, which negatively affect the electrochemical performance of Li-ion batteries. Ex situ X-ray absorption (XRF/XANES), Raman, and fluorescence spectroscopy, along with imaging of Li(x)Ni(0.5)Mn(1.5)O(4-δ) positive and graphite negative electrodes from tested Li-ion batteries, reveal the formation of a variety of Mn(II/III) and Ni(II) complexes with ß-diketonate ligands. These metal complexes, which are generated upon anodic oxidation of ethyl and diethyl carbonates at Li(x)Ni(0.5)Mn(1.5)O(4-δ), form a surface film that partially dissolves in the electrolyte. The dissolved Mn(III) complexes are reduced to their Mn(II) analogues, which are incorporated into the solid electrolyte interphase surface layer at the graphite negative electrode. This work elucidates possible reaction pathways and evaluates their implications for Li(+) transport kinetics in Li-ion batteries.

The origin of high electrolyte-electrode interfacial resistances in lithium cells containing garnet type solid electrolytes.

Dense LLZO (Al-substituted Li7La3Zr2O12) pellets were processed in controlled atmospheres to investigate the relationships between the surface chemistry and interfacial behavior in lithium cells. Laser induced breakdown spectroscopy (LIBS), scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy, synchrotron X-ray photoelectron spectroscopy (XPS) and soft X-ray absorption spectroscopy (XAS) studies revealed that Li2CO3 was formed on the surface when LLZO pellets were exposed to air. The distribution and thickness of the Li2CO3 layer were estimated by a combination of bulk and surface sensitive techniques with various probing depths. First-principles thermodynamic calculations confirmed that LLZO has an energetic preference to form Li2CO3 in air. Exposure to air and the subsequent formation of Li2CO3 at the LLZO surface is the source of the high interfacial impedances observed in cells with lithium electrodes. Surface polishing can effectively remove Li2CO3 and dramatically improve the interfacial properties. Polished samples in lithium cells had an area specific resistance (ASR) of only 109 Ω cm(2) for the LLZO/Li interface, the lowest reported value for Al-substituted LLZO. Galvanostatic cycling results obtained from lithium symmetrical cells also suggest that the quality of the LLZO/lithium interface has a significant impact on the device lifetime.

Finite temperature effects on the X-ray absorption spectra of lithium compounds: first-principles interpretation of X-ray Raman measurements.

We elucidate the role of room-temperature-induced instantaneous structural distortions in the Li K-edge X-ray absorption spectra (XAS) of crystalline LiF, Li2SO4, Li2O, Li3N, and Li2CO3 using high resolution X-ray Raman spectroscopy (XRS) measurements and first-principles density functional theory calculations within the eXcited electron and Core Hole approach. Based on thermodynamic sampling via ab initio molecular dynamics simulations, we find calculated XAS in much better agreement with experiment than those computed using the rigid crystal structure alone. We show that local instantaneous distortion of the atomic lattice perturbs the symmetry of the Li 1s core-excited-state electronic structure, broadening spectral line-shapes and, in some cases, producing additional spectral features. The excellent agreement with high-resolution XRS measurements validates the accuracy of our first-principles approach to simulating XAS, and provides both accurate benchmarks for model compounds and a predictive theoretical capability for identification and characterization of multi-component systems, such as lithium-ion batteries, under working conditions.

Synchrotron Near-Field Infrared Nanospectroscopy and Nanoimaging of Lithium Fluoride in Solid Electrolyte Interphases in Li-Ion Battery Anodes.

Lithium fluoride (LiF) is a ubiquitous component in the solid electrolyte interphase (SEI) layer in Li-ion batteries. However, its nanoscale structure, morphology, and topology, important factors for understanding LiF and SEI film functionality, including electrode passivity, are often unknown due to limitations in spatial resolution of common characterization techniques. Ultrabroadband near-field synchrotron infrared nanospectroscopy (SINS) enables such detection and mapping of LiF in SEI layers in the far-infrared region down to ca. 322 cm-1 with a nanoscale spatial resolution of ca. 20 nm. The surface sensitivity of SINS and the large infrared absorption cross section of LiF, which can support local surface phonons under certain circumstances, enabled characterization of model LiF samples of varying structure, thickness, surface roughness, and degree of crystallinity, as confirmed by atomic force microscopy, attenuated total reflectance FTIR, SINS, X-ray photoelectron spectroscopy, high-angle annular dark-field, and scanning transmission electron microscopy. Enabled by this approach, LiF within SEI films formed on Cu, Si, and metallic glass Si40Al50Fe10 electrodes was detected and characterized. The nanoscale morphologies and topologies of LiF in these SEI layers were evaluated to gain insights into LiF nucleation, growth, and the resulting nuances in the electrode surface passivity.

Light-driven C-H activation mediated by 2D transition metal dichalcogenides.

C-H bond activation enables the facile synthesis of new chemicals. While C-H activation in short-chain alkanes has been widely investigated, it remains largely unexplored for long-chain organic molecules. Here, we report light-driven C-H activation in complex organic materials mediated by 2D transition metal dichalcogenides (TMDCs) and the resultant solid-state synthesis of luminescent carbon dots in a spatially-resolved fashion. We unravel the efficient H adsorption and a lowered energy barrier of C-C coupling mediated by 2D TMDCs to promote C-H activation. Our results shed light on 2D materials for C-H activation in organic compounds for applications in organic chemistry, environmental remediation, and photonic materials.

Light-driven C-H activation mediated by 2D transition metal dichalcogenides.

C-H bond activation enables the facile synthesis of new chemicals. While C-H activation in short-chain alkanes has been widely investigated, it remains largely unexplored for long-chain organic molecules. Here, we report light-driven C-H activation in complex organic materials mediated by 2D transition metal dichalcogenides (TMDCs) and the resultant solid-state synthesis of luminescent carbon dots in a spatially-resolved fashion. We unravel the efficient H adsorption and a lowered energy barrier of C-C coupling mediated by 2D TMDCs to promote C-H activation and carbon dots synthesis. Our results shed light on 2D materials for C-H activation in organic compounds for applications in organic chemistry, environmental remediation, and photonic materials.

Nanomaterials for renewable energy production and storage.

Over the past decades, there have been many projections on the future depletion of the fossil fuel reserves on earth as well as the rapid increase in green-house gas emissions. There is clearly an urgent need for the development of renewable energy technologies. On a different frontier, growth and manipulation of materials on the nanometer scale have progressed at a fast pace. Selected recent and significant advances in the development of nanomaterials for renewable energy applications are reviewed here, and special emphases are given to the studies of solar-driven photocatalytic hydrogen production, electricity generation with dye-sensitized solar cells, solid-state hydrogen storage, and electric energy storage with lithium ion rechargeable batteries.

Arsenic removal from groundwater using iron electrocoagulation: effect of charge dosage rate.

We demonstrate that electrocoagulation (EC) using iron electrodes can reduce arsenic below 10 µg/L in synthetic Bangladesh groundwater and in real groundwater from Bangladesh and Cambodia, while investigating the effect of operating parameters that are often overlooked, such as charge dosage rate. We measure arsenic removal performance over a larger range of current density than in any other single previous EC study (5000-fold: 0.02 - 100 mA/cm(2)) and over a wide range of charge dosage rates (0.060 - 18 Coulombs/L/min). We find that charge dosage rate has significant effects on both removal capacity (µg-As removed/Coulomb) and treatment time and is the appropriate parameter to maintain performance when scaling to different active areas and volumes. We estimate the operating costs of EC treatment in Bangladesh groundwater to be $0.22/m(3). Waste sludge (~80 - 120 mg/L), when tested with the Toxic Characteristic Leachate Protocol (TCLP), is characterized as non-hazardous. Although our focus is on developing a practical device, our results suggest that As[III] is mostly oxidized via a chemical pathway and does not rely on processes occurring at the anode. Supplementary materials are available for this article. Go to the publisher's online edition of Journal of Environmental Science and Health, Part A, to view the free supplemental file.

The Effect of the SEI Layer Mechanical Deformation on the Passivity of a Si Anode in Organic Carbonate Electrolytes.

The solid electrolyte interphase (SEI) on a Si negative electrode in carbonate-based organic electrolytes shows intrinsically poor passivating behavior, giving rise to unsatisfactory calendar life of Li-ion batteries. Moreover, mechanical strains induced in the SEI due to large volume changes of Si during charge-discharge cycling could contribute to its mechanical instability and poor passivating behavior. This study elucidates the influence that static mechanical deformation of the SEI has on the rate of unwanted parasitic reactions at the Si/electrolyte interface as a function of electrode potential. The experimental approach involves the utilization of Si thin-film electrodes on substrates with disparate elastic moduli, which either permit or suppress the SEI deformation in response to Si volume changes upon charging-discharging. We find that static mechanical stretching and deformation of the SEI results in an increased parasitic electrolyte reduction current on Si. Furthermore, attenuated total reflection and near-field Fourier-transform infrared nanospectroscopy reveal that the static mechanical stretching and deformation of the SEI fosters a selective transport of linear carbonate solvent through, and nanoconfinement within, the SEI. These, in turn, promote selective solvent reduction and continuous electrolyte decomposition on Si electrodes, reducing the calendar life of Si anode-based Li-ion batteries. Finally, possible correlations between the structure and chemical composition of the SEI layer and its mechanical and chemical resilience under prolonged mechanical deformation are discussed in detail.

Nano-FTIR Spectroscopy of the Solid Electrolyte Interphase Layer on a Thin-Film Silicon Li-Ion Anode.

Si anodes for Li-ion batteries are notorious for their large volume expansion during lithiation and the corresponding detrimental effects on cycle life. However, calendar life is the primary roadblock for widespread adoption. During calendar life aging, the main origin of impedance increase and capacity fade is attributed to the instability of the solid electrolyte interphase (SEI). In this work, we use ex situ nano-Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy to characterize the structure and composition of the SEI layer on amorphous Si thin films after an accelerated calendar aging protocol. The characterization of the SEI on non-washed and washed electrodes shows that brief washing in dimethyl carbonate results in large changes to the film chemistry and topography. Detailed examination of the non-washed electrodes during the first lithiation and after an accelerated calendar aging protocol reveals that PF6- and its decomposition products tend to accumulate in the SEI due to the preferential transport of PF6- ions through polyethylene oxide-like species in the organic part of the SEI layer. This work demonstrates the importance of evaluating the SEI layer in its intrinsic, undisturbed form and new strategies to improve the passivation of the SEI layer are proposed.

In situ infrared nanospectroscopy of the local processes at the Li/polymer electrolyte interface.

Solid-state batteries possess the potential to significantly impact energy storage industries by enabling diverse benefits, such as increased safety and energy density. However, challenges persist with physicochemical properties and processes at electrode/electrolyte interfaces. Thus, there is great need to characterize such interfaces in situ, and unveil scientific understanding that catalyzes engineering solutions. To address this, we conduct multiscale in situ microscopies (optical, atomic force, and infrared near-field) and Fourier transform infrared spectroscopies (near-field nanospectroscopy and attenuated total reflection) of intact and electrochemically operational graphene/solid polymer electrolyte interfaces. We find nanoscale structural and chemical heterogeneities intrinsic to the solid polymer electrolyte initiate a cascade of additional interfacial nanoscale heterogeneities during Li plating and stripping; including Li-ion conductivity, electrolyte decomposition, and interphase formation. Moreover, our methodology to nondestructively characterize buried interfaces and interphases in their native environment with nanoscale resolution is readily adaptable to a number of other electrochemical systems and battery chemistries.

Recent Applications of Langmuir-Blodgett Technique in Battery Research.

The Langmuir-Blodgett (LB) technique, in which monolayers are commonly transferred from a liquid/gas interface to a solid surface, allows convenient fabrication of highly ordered thin films with molecular-level precision. This method is widely applicable to substances ranging from organic molecules to nanomaterials. Therefore, LB methods have provided a critical toolbox for researchers to engineer nanoarchitectures. The LB fabrication process is also compatible with numerous substrate materials over large areas, which is advantageous for practical application. Despite its wide applicability, the LB strategy has not been extensively employed in battery studies. The versatility of LB film, along with the accumulated knowledge associated with this technique, makes it a promising platform for promoting battery chemistry evolution. This Review summarizes recent advances of LB methods for high-performance battery development, including preparation of electrode materials, fabrication of functional layers, and battery diagnosis and thus illustrates the high utility of LB approaches in battery research.

The interaction of Li+ with single-layer and few-layer graphene.

The interaction of Li(+) with single and few layer graphene is reported. In situ Raman spectra were collected during the electrochemical lithiation of the single- and few-layer graphene. While the interaction of lithium with few layer graphene seems to resemble that of graphite, single layer graphene behaves very differently. The amount of lithium absorbed on single layer graphene seems to be greatly reduced due to repulsion forces between Li(+) at both sides of the graphene layer.