The adsorptive removal of chromium (VI) in aqueous solution by novel natural zeolite based hollow fibre ceramic membrane.

Adsorption is one of the most efficient ways to remove heavy metal from wastewater. In this study, the adsorptive removal of hexavalent chromium, Cr (VI) from aqueous solution was investigated using natural zeolite, clinoptilolite, in the form of hollow fibre ceramic membrane (HFCM). The HFCM sample was prepared using phase inversion-based extrusion technique and followed by sintering process at different sintering temperatures in the range of 900-1050 °C. The fabricated HFCM was characterised using scanning electron microscopy (SEM), contact angle, water permeability, and mechanical strength for all HFCMs sintered at different temperatures. The adsorption and filtration test of Cr (VI) were performed using an in-house water permeation set up with a dead-end cross-flow permeation test. An asymmetric structure with sponge- and finger-like structures across the cross-section of HFCM was observed using SEM. Based on the characterisation data, 1050 °C was chosen to be the best sintering temperature as the water permeability and mechanical strength of this HFCM were 29.14 L/m2∙h and 50.92 MPa, respectively. The performance of the HFCM in adsorption/filtration was 44% of Cr (VI) removal at the Cr (VI) concentration of 40 mg/L and pH 4. In addition, the mathematical model was also performed in simulating the experimental data obtained from this study. All in all, the natural zeolite-based HFCM has a potential as a single-step Cr (VI) removal by membrane adsorption for the wastewater treatment.

[Clinical significance of chronologic immature platelet fraction analysis in TAFRO syndrome].

TAFRO syndrome is characterized by thrombocytopenia with unknown etiology. The assessment of immature platelet fraction (IPF) is useful for differential diagnoses that include thrombocytopenia. However, the significance of IPF in cases of TAFRO syndrome remains to be reported. We present a case of TAFRO syndrome wherein the patient demonstrated a marked increase in IPF without thrombocytopenia, which offers vital information concerning TAFRO diagnosis and the serial measurements of IPF during treatment. A 65-year-old man presenting with fever was admitted to our hospital. He exhibited mild splenomegaly and lymphadenopathy, as well as rapidly worsening renal failure and fluid retention. These indications prompted the initiation of corticosteroid therapy. A normal platelet count and aberrantly high IPF implied abnormal thrombopoiesis, and subsequent bone-marrow findings suggested TAFRO syndrome. The platelet counts started to decrease following the corticosteroid therapy, but the treatment refractoriness prompted the urgent administration of rituximab. Thereafter, the platelet count nadir remained for approximately one month, whereas the decreasing IPF trend preceded platelet recovery. In the present case, a high pre-treatment IPF was demonstrated before the emergence of thrombocytopenia, and a decreasing trend of IPF was observed before platelet recovery during treatment. Therefore, serial IPF measurements could be useful for the early diagnosis and prognostication of TAFRO syndrome.

Molecular typing of environmental Cryptococcus neoformans/C. gattii species complex isolates from Manaus, Amazonas, Brazil.

Cryptococcus neoformans and Cryptococcus gattii are the main causative agents of cryptococcosis, a systemic fungal disease that affects internal organs and skin, and which is acquired by inhalation of spores or encapsulated yeasts. It is currently known that the C. neoformans/C. gattii species complex has a worldwide distribution, however, some molecular types seem to prevail in certain regions. Few environmental studies of Cryptococcus have been conducted in the Brazilian Amazon. This is the first ecological study of the pathogenic fungi C. neoformans/C. gattii species complex in the urban area of Manaus, Amazonas, Brazil. A total of 506 samples from pigeon droppings (n = 191), captive bird droppings (n = 60) and tree hollows (n = 255) were collected from June 2012 to January 2014 at schools and public buildings, squares, pet shops, households, the zoo and the bus station. Samples were plated on niger seed agar (NSA) medium supplemented with chloramphenicol and incubated at 25°C for 5 days. Dark-brown colonies were isolated and tested for thermotolerance at 37°C, cycloheximide resistance and growth on canavanine-glycine-bromothymol blue agar. Molecular typing was done by PCR-RFLP. Susceptibility to the antifungal drugs amphotericin B, fluconazole, itraconazole and ketoconazole was tested using Etest(®) strips. In total, 13 positive samples were obtained: one tree hollow (C. gattiiVGII), nine pigeon droppings (C. neoformansVNI) and three captive bird droppings (C. neoformansVNI). The environmental cryptococcal isolates found in this study were of the same molecular types as those responsible for infections in Manaus.

Management of three cardiogenic pulmonary edemas occurring in a patient scheduled for left ventricular assist device implantation: indicators for determining left ventricular assist device pump speed.

A male patient with Marfan syndrome underwent aortic root replacement and developed left ventricular (LV) failure. Four years later, he underwent aortic arch and aortic valve replacement. Thereafter, his LV failure progressed, and cardiogenic pulmonary edema (CPE) appeared, which we treated with extracorporeal LV assist device (LVAD) placement. Three months later, the patient developed aspiration pneumonia, which caused hyperdynamic right ventricle (RV) and CPE. We treated by changing his pneumatic LVAD to a high-flow centrifugal pump. A month later, he underwent thoracoabdominal aortic replacement. After four weeks, he developed septic thrombosis and LVAD failure, which caused CPE. We treated with LVAD circuit replacement and an additional membrane oxygenator. Four months later, he underwent DuraHeart(®) implantation. During this course, pulmonary artery wedge pressure (PAWP) varied markedly. Additionally, systolic pulmonary artery pressure (sPAP), left atrial diameter (LAD), RV end-diastolic diameter (RVEDD) and estimated RV systolic pressure (esRVP) changed with PAWP changes. In this patient, LV failure and hyperdynamic RV caused the CPEs, which we treated by adjusting the LVAD output to the RV output. Determining LVAD output, RV function and LV end-diastolic diameter are typically referred, and PAWP, LAD, RVEDD, and sPAP could be also referred.

Bézier Curve Method to Compute Various Meniscus Shapes.

This paper is an extension of our earlier paper in which it was shown that the meniscus shape in a cylindrical capillary could be computed by solving the Young-Laplace equation via optimization of a Bézier curve. This work extends the previous work by demonstrating that the method is applicable to predict the meniscus shape not only in a cylindrical capillary but also in other cases, such as at a tilted plate, between two plates, and for a sessile drop. Numerous works have attempted previously to solve the Young-Laplace equation, and their results all agree with this paper's validating its method. All the preceding approaches, however, used special techniques to solve the differential equation, while the Bézier curve method proposed in this work is more simple, which allows it to maintain greater computational simplicity. Moreover, the Bézier curve method can be applied to solve many other different differential equations in the same way as shown in this work. The effect of the Bézier curve degree on the precision of prediction was also thoroughly investigated. It was found that the 4th degree Bézier curve was required to predict the meniscus shape precisely in a cylindrical capillary, against a tilted plate, and between two plates, while the 5th degree was required for the shape of the sessile drop.

Simultaneous separation and degradation of methylene blue by a thin film nanocomposite membrane containing TiO2/MWCNTs nanophotocatalyst.

ABSTRACTAn innovative photocatalytic thin film nanocomposite (TFN) membrane was prepared and used for the simultaneous separation/degradation of methylene blue (MB) under UV irradiation. For this purpose, we used the sol-gel method to prepare the TiO2/MWCNTs nanophotocatalyst and added to the 1,3-phenylenediamine (MPD) solution during interfacial polymerization (IP) of 1,3,5-benzenetricarbonyl chloride (TMC) and 1,3-phenylenediamine monomers on the polysulfone (PSF) support. Using scanning electron microscopy (SEM) analysis and studying the cross-sectional images of membrane samples, it was revealed that the polyamide (PA) thin layer was well fabricated over the support membrane. The attendance of the TiO2/MWCNTs nanophotocatalyst in the PA thin layer of TFN samples was also proved using EDX (energy-dispersive X-ray) analysis. According to the results of the contact angle (CA), it is clear that the hydrophilicity of membrane samples first increased and then decreased by enhancing the TiO2/MWCNTs nanophotocatalyst content in the PA thin layer. In comparison with the pristine thin film composite (TFC) membrane, TFN samples showed higher water flux and MB removal when they were exposed to UV light. Finally, it turned out that the TFN membrane comprising 0.2 wt. % TiO2/MWCNTs nanophotocatalyst (TFN 0.2) had the foremost efficiency among TFNs with the water flux of 13 L/m2·hr and dye separation/degradation of almost 100% under UV irradiation.

Clinical Results of Surgical Treatment for Comminuted Radial Head and Neck Fracture: Headless Compression Screws Versus Plate Fixation.

Background: We surgically treated comminuted radial head and neck fractures using headless compression screws, including multiple screws for the radial head and a single oblique screw for the radial neck. This study aimed to compare the clinical and radiological results for comminuted radial head and neck fractures between surgery using headless compression screws with a single oblique screw for the radial neck, our new procedure, and a plate system precontoured to the proximal radius. Methods: This retrospective study included 23 patients (11 and 12 in the screw and plate groups, respectively). The fractures were type 3 according to the Mason-Johnston classification modified by Broberg and Morrey. Clinical outcomes analyzed included the motion range of the elbow and forearm, Mayo Elbow Performance Score, and radiological assessments. In addition, postoperative complications were also investigated. The average follow-up was 18 months. Results: The bone union was achieved in all the patients, and there were no significant differences in clinical outcomes and radiological assessments except forearm supination (p = 0.02). Furthermore, additional surgical procedures were performed in one and five patients in the screw and plate groups, respectively (p = 0.16). Posterior nerve palsy was observed in two patients in the plate group. Complications were observed in one and six patients in the screw and plate groups, respectively (p = 0.07). Conclusion: Both surgical procedures achieved good clinical and radiological outcomes with bone and ligament injury repair. The screw group had a greater range of forearm supination than the plate group.

Magnesium Oxide Nanoparticles for the Adsorption of Pentavalent Arsenic from Water: Effects of Calcination.

The occurrence of heavy metal ions in water is intractable, and it has currently become a serious environmental issue to deal with. The effects of calcining magnesium oxide at 650 °C and the impacts on the adsorption of pentavalent arsenic from water are reported in this paper. The pore nature of a material has a direct impact on its ability to function as an adsorbent for its respective pollutant. Calcining magnesium oxide is not only beneficial in enhancing its purity but has also been proven to increase the pore size distribution. Magnesium oxide, as an exceptionally important inorganic material, has been widely studied in view of its unique surface properties, but the correlation between its surface structure and physicochemical performance is still scarce. In this paper, magnesium oxide nanoparticles calcined at 650 °C are assessed to remove the negatively charged arsenate ions from an aqueous solution. The increased pore size distribution was able to give an experimental maximum adsorption capacity of 115.27 mg/g with an adsorbent dosage of 0.5 g/L. Non-linear kinetics and isotherm models were studied to identify the adsorption process of ions onto the calcined nanoparticles. From the adsorption kinetics study, the non-linear pseudo-first order showed an effective adsorption mechanism, and the most suitable adsorption isotherm was the non-linear Freundlich isotherm. The resulting R2 values of other kinetic models, namely Webber-Morris and Elovich, were still below those of the non-linear pseudo-first-order model. The regeneration of magnesium oxide in the adsorption of negatively charged ions was determined by making comparisons between fresh and recycled adsorbent that has been treated with a 1 M NaOH solution.

Calculation of the Meniscus Shape Formed under Gravitational Force by Solving the Young-Laplace Differential Equation Using the Bézier Curve Method.

This work presents a method to calculate the meniscus shape by solving the differential equation based on the Young-Laplace equation. More specifically, the differential equation is solved by applying the cubic Bézier curve. A complicated nonlinear differential equation is solved using the Bézier control points and the least-squares method while maintaining computational simplicity. The results show all of the expected features of the meniscus under the gravitational force. A brief discussion is also made on the effect of the errors on the results. The method is further validated by its agreement with the numerical solutions reported in the existing literature.

Fouling Prevention in Polymeric Membranes by Radiation Induced Graft Copolymerization.

The application of membrane processes in various fields has now undergone accelerated developments, despite the presence of some hurdles impacting the process efficiency. Fouling is arguably the main hindrance for a wider implementation of polymeric membranes, particularly in pressure-driven membrane processes, causing higher costs of energy, operation, and maintenance. Radiation induced graft copolymerization (RIGC) is a powerful versatile technique for covalently imparting selected chemical functionalities to membranes' surfaces, providing a potential solution to fouling problems. This article aims to systematically review the progress in modifications of polymeric membranes by RIGC of polar monomers onto membranes using various low- and high-energy radiation sources (UV, plasma, γ-rays, and electron beam) for fouling prevention. The feasibility of the modification method with respect to physico-chemical and antifouling properties of the membrane is discussed. Furthermore, the major challenges to the modified membranes in terms of sustainability are outlined and the future research directions are also highlighted. It is expected that this review would attract the attention of membrane developers, users, researchers, and scientists to appreciate the merits of using RIGC for modifying polymeric membranes to mitigate the fouling issue, increase membrane lifespan, and enhance the membrane system efficiency.

Flux Increase Occurring When an Ultrafiltration Membrane Is Flipped from a Normal to an Inverted Position-Experiments and Theory.

The effects of flipping membranes with hydrophilic/hydrophobic asymmetry are well documented in the literature, but not much is known on the impact of flipping a membrane with dense/porous layer asymmetry. In this work, the pure water flux (PWF) of a commercial polyethersulfone (PES) membrane and a ceramic ultrafiltration (UF) membrane was measured in the normal and inverted positions. Our experimental results showed that the PWF was two orders of magnitude higher when the PES membrane was flipped to the inverted position, while the increase was only two times for the ceramic membrane. The filtration experiments were also carried out using solutions of bovine serum albumin and poly(vinylpyrrolidone). A mathematical model was further developed to explain the PWF increase in the inverted position based on the Bernoulli's rule, considering a straight cylindrical pore of small radius connected to a pore of larger radius in series. It was found by simulation that a PWF increase was indeed possible when the solid ceramic membrane was flipped, maintaining its pore geometry. The flow from a layer with larger pore size to a layer with smaller pore size occurred in the backwashing of the fouled membrane and in forward and pressure-retarded osmosis when the membrane was used with its active layer facing the draw solution (AL-DS). Therefore, this work is of practical significance for the cases where the direction of the water flow is in the inverted position of the membrane.

Desalination at ambient temperature and pressure by a novel class of biporous anisotropic membrane.

Recent scientific advances have made headway in addressing pertinient issues in climate change and the sustainability of our natural environment. This study makes use of a novel approach to desalination that is environment friendly, naturally sustainable and energy efficient, meaning that it is also cost efficient. Evaporation is a key phenomenon in the natural environment and used in many industrial applications including desalination. For a liquid droplet, the vapor pressure changes due to the curved liquid-vapor interface at the droplet surface. The vapor pressure at a convex surface in a pore is, therefore, higher than that at a flat surface due to the capillary effect, and this effect is enhanced as the pore radius decreases. This concept inspired us to design a novel biporous anisotropic membrane for membrane distillation (MD), which enables to desalinate water at ambient temperature and pressure by applying only a small transmembrane temperature gradient. The novel membrane is described as a super-hydrophobic nano-porous/micro-porous composite membrane. A laboratory-made membrane with specifications determined by the theoretical model was prepared for model validation and tested for desalination at different feed inlet temperatures by direct contact MD. A water vapor flux as high as 39.94 ± 8.3 L m-2 h-1 was achieved by the novel membrane at low feed temperature (25 °C, permeate temperature = 20 °C), while the commercial PTFE membrane, which is widely used in MD research, had zero flux under the same operating conditions. As well, the fluxes of the fabricated membrane were much higher than the commercial membrane at various inlet feed temperatures.

Model analysis on effect of temperature on the solubility of recycling of Polyethylene Terephthalate (PET) plastic.

The massive increase in the use of PET plastic bottles has raised the challenge of accumulated waste plastics disposal and its related environmental concerns. Reusing this plastic waste through a solvent-based recycling process seems to be an eco-friendly solution for eliminating waste plastic and converting them into high quality products. The selection of solvent with its temperature requirement for the dissolution of polymeric materials is crucial in the solvent-based recycling process. Therefore, an innovative MATLAB program named HSPs-TPT was designed and constructed in this work to evaluate the dissolving power of solvents. Through this program, the solubility of the waste PET polymer was examined in thirteen (13) different solvents at different temperatures. As a results, the degree of waste PET polymer dissolution in the solvents was presented as the polymer-solvent solubility diagram, which provided the information about the relative energy difference (RED) change with the temperature rise. The program also provided the temperature range effective for the dissolution of PET by indicating the minimum and maximum solubility point for each solvent, which was further validated by the experimental data found in the literature. The proposed MATLAB program can numerically analyse the solubility of a polymer in different solvents in a short time for the recycling process and fabrication of different value-added plastic products such as polymer monoliths and membrane filters.

Controlling Air Bubble Formation Using Hydrophilic Microfiltration Diffuser for C. vulgaris Cultivation.

In this project, a commercial polytetrafluoroethylene (PTFE) membrane was coated with a thin layer of polyether block amide (PEBAX) via vacuum filtration to improve hydrophilicity and to study the bubble formation. Two parameters, namely PEBAX concentration (of 0-1.5 wt%) and air flow rate (of 0.1-50 mL/s), were varied and their effects on the bubble size formation were investigated. The results show that the PEBAX coating reduced the minimum membrane pore size from 0.46 µm without coating (hereafter called PEBAX0) to 0.25 µm for the membrane coated with 1.5wt% of PEBAX (hereafter called PEBAX1.5). The presence of polar functional groups (N-H and C=O) in PEBAX greatly improved the membrane hydrophilicity from 118° for PEBAX0 to 43.66° for PEBAX1.5. At an air flow rate of 43 mL/s, the equivalent bubble diameter size decreased from 2.71 ± 0.14 cm for PEBAX0 to 1.51 ± 0.02 cm for PEBAX1.5. At the same air flow rate, the frequency of bubble formation increased six times while the effective gas-liquid contact area increased from 47.96 cm2/s to 85.6 cm2/s. The improved growth of C. vulgaris from 0.6 g/L to 1.3 g/L for PEBAX1.5 also shows the potential of the PEBAX surface coating porous membrane as an air sparger.

Waste Reutilization in Polymeric Membrane Fabrication: A New Direction in Membranes for Separation.

In parallel to the rapid growth in economic and social activities, there has been an undesirable increase in environmental degradation due to the massively produced and disposed waste. The need to manage waste in a more innovative manner has become an urgent matter. In response to the call for circular economy, some solid wastes can offer plenty of opportunities to be reutilized as raw materials for the fabrication of functional, high-value products. In the context of solid waste-derived polymeric membrane development, this strategy can pave a way to reduce the consumption of conventional feedstock for the production of synthetic polymers and simultaneously to dampen the negative environmental impacts resulting from the improper management of these solid wastes. The review aims to offer a platform for overviewing the potentials of reutilizing solid waste in liquid separation membrane fabrication by covering the important aspects, including waste pretreatment and raw material extraction, membrane fabrication and characterizations, as well as the separation performance evaluation of the resultant membranes. Three major types of waste-derived polymeric raw materials, namely keratin, cellulose, and plastics, are discussed based on the waste origins, limitations in the waste processing, and their conversion into polymeric membranes. With the promising material properties and viability of processing facilities, recycling and reutilization of waste resources for membrane fabrication are deemed to be a promising strategy that can bring about huge benefits in multiple ways, especially to make a step closer to sustainable and green membrane production.

Planning of smart gating membranes for water treatment.

The use of membranes in desalination and water treatment has been intensively studied in recent years. The conventional membranes however have various problems such as uncontrollable pore size and membrane properties, which prevents membranes from quickly responding to alteration of operating and environmental conditions. As a result the membranes are fouled, and their separation performance is lowered. The preparation of smart gating membranes inspired by cell membranes is a new method to face these challenges. Introducing stimuli-responsive functional materials into traditional porous membranes and use of hydrogels and microgels can change surface properties and membrane pore sizes under different conditions. This review shows potential of smart gating membranes in water treatment. Various types of stimuli-response such as those of thermo-, pH-, ion-, molecule-, UV light-, magnetic-, redox- and electro-responsive gating membranes along with various gel types such as those of polyelectrolyte, PNIPAM-based, self-healing hydrogels and microgel based-smart gating membranes are discussed. Design strategies, separation mechanisms and challenges in fabrication of smart gating membranes in water treatment are also presented. It is demonstrated that experimental and modeling and simulation results have to be utilized effectively to produce smart gating membranes.

Research and Development Journey and Future Trends of Hollow Fiber Membranes for Purification Applications (1970-2020): A Bibliometric Analysis.

Hollow fiber membrane (HFM) technology has received significant attention due to its broad range separation and purification applications in the industry. In the current study, we applied bibliometric analysis to evaluate the global research trends on key applications of HFMs by evaluating the global publication outputs. Results obtained from 5626 published articles (1970-2020) from the Scopus database were further manipulated using VOSviewer software through cartography analysis. The study emphasizes the performance of most influential annual publications covering mainstream journals, leading countries, institutions, leading authors and author's keywords, as well as future research trends. The study found that 62% of the global HFM publications were contributed by China, USA, Singapore, Japan and Malaysia, followed by 77 other countries. This study will stimulate the researchers by showing the future-minded research directions when they select new research areas, particularly in those related to water treatment, biomedical and gas separation applications of HFM.

Synthesis and Characterization of Titanium Dioxide Hollow Nanofiber for Photocatalytic Degradation of Methylene Blue Dye.

Environmental crisis and water contamination have led to worldwide exploration for advanced technologies for wastewater treatment, and one of them is photocatalytic degradation. A one-dimensional hollow nanofiber with enhanced photocatalytic properties is considered a promising material to be applied in the field. Therefore, we synthesized titanium dioxide hollow nanofibers (THNF) with extended surface area, light-harvesting properties and an anatase-rutile heterojunction via a template synthesis method and followed by a calcination process. The effect of calcination temperature on the formation and properties of THNF were determined and the possible mechanism of THNF formation was proposed. THNF nanofibers produced at 600 °C consisted of a mixture of 24.2% anatase and 75.8% rutile, with a specific surface area of 81.2776 m2/g. The hollow nanofibers also outperformed the other catalysts in terms of photocatalytic degradation of MB dye, at 85.5%. The optimum catalyst loading, dye concentration, pH, and H2O2 concentration were determined at 0.75 g/L, 10 ppm, pH 11, and 10 mM, respectively. The highest degradation of methylene blue dye achieved was 95.2% after 4 h of UV irradiation.

Comparison of modified Das De procedure with Du Vries procedure for traumatic peroneal tendon dislocation.

BACKGROUND: For peroneal tendon dislocation, various surgical procedures have been described. Das De et al. reported good clinical results using retinaculum repair. However, their reports are limited to case series. We have simplified the Das De procedure since 1996. The purpose of this study is to investigate the clinical outcomes of our modified Das De procedure (MD) and compare these clinical outcomes to those of the Du Vries procedure (DV) that was performed in our hospital until 1996. PATIENTS: From 1996 to 2007, 19 patients were treated by MD and from 1988 to 1996, 15 patients were treated by DV. RESULTS: A mean preoperative Ankle-Hindfoot Scale was 78.4 points (range: 65-84) in the MD group and 77.2 points (range: 67-87) in the DV group. A mean postoperative Ankle-Hindfoot Scale was 93.4 points in the MD group and 89.4 points in the DV group. Two patients (13.3%) in the DV group suffered postoperative peroneal tendon redislocation. In the MD group, there was no postoperative peroneal tendon redislocation or complication related to skin incision. In athletes, 80.0% in the MD group and 54.5% in the DV group were able to return to their previous sports. The mean duration to return to sports was 2.9 months in the MD group and 3.9 months in the DV group (p < 0.05). CONCLUSIONS: MD provided similar or slightly better clinical outcomes with less complication as compared to DV. For athletes, the rate of return to sports was higher and the duration to return to sports was significantly shorter in the MD group.