RESUMEN
X-ray microscopy at photon energies above 15 keV is very attractive for the investigation of atomic and nanoscale properties of technologically relevant structural and bio materials. This method is limited by the quality of X-ray optics. Multilayer Laue lenses (MLLs) have the potential to make a major impact in this field because, as compared to other X-ray optics, they become more efficient and effective with increasing photon energy. In this work, MLLs were utilized with hard X-rays at photon energies up to 34.5 keV. The design, fabrication, and performance of these lenses are presented, and their application in several imaging configurations is described. In particular, two "full field" modes of imaging were explored, which provide various contrast modalities that are useful for materials characterisation. These include point projection imaging (or Gabor holography) for phase contrast imaging and direct imaging with both bright-field and dark-field illumination. With high-efficiency MLLs, such modes offer rapid data collection as compared with scanning methods as well as a large field of views.
RESUMEN
An outstanding question in X-ray single particle imaging experiments has been the feasibility of imaging sub 10-nm-sized biomolecules under realistic experimental conditions where very few photons are expected to be measured in a single snapshot and instrument background may be significant relative to particle scattering. While analyses of simulated data have shown that the determination of an average image should be feasible using Bayesian methods such as the EMC algorithm, this has yet to be demonstrated using experimental data containing realistic non-isotropic instrument background, sample variability and other experimental factors. In this work, we show that the orientation and phase retrieval steps work at photon counts diluted to the signal levels one expects from smaller molecules or with weaker pulses, using data from experimental measurements of 60-nm PR772 viruses. Even when the signal is reduced to a fraction as little as 1/256, the virus electron density determined using ab initio phasing is of almost the same quality as the high-signal data. However, we are still limited by the total number of patterns collected, which may soon be mitigated by the advent of high repetition-rate sources like the European XFEL and LCLS-II.
RESUMEN
During the last few years, there has been an alarming increase in the amount of nickel (Ni) being released into the environment, primarily due to its use in the production of stainless steel but also from other sources such as batteries manufacturing and consequent disposal. The established biotic ligand models provide precise estimates for Ni bioavailability, in contrast, studies describing the mechanisms underpinning toxicological effect of Ni are scarce. This study exploits RNA-seq to determine the transcriptomic responses of isopods using Porcellionides pruinosus as an example of a terrestrial metal-resistant woodlouse. Furthermore, the recently proposed model for Ni adverse outcome pathways (Ni-AOP) presents an unprecedented opportunity to fit isopod responses to Ni toxicity and define Porcellionides pruinosus as a metalomic model. Prior to this study, P. pruinosus represented an important environmental sentinel, though lacking genetic/omic data. The reference transcriptome generated here thus represents a major advance and a novel resource. A detailed annotation of the transcripts obtained is presented together with the homology to genes/gene products from Metazoan and Arthropoda phylum, Gene Ontology (GO) classification, clusters of orthologous groups (COG) and assignment to KEGG metabolic pathways. The differential gene expression comparison was determined in response to nickel (Ni) exposure and used to derive the enriched pathways and processes. It revealed a significant impact on ion trafficking and storage, oxidative stress, neurotoxicity, reproduction impairment, genetics and epigenetics. Many of the processes observed support the current Ni-AOP although the data highlights that the current model can be improved by including epigenetic endpoints, which represents key chronic risks under a scenario of Ni toxicity.
Asunto(s)
Contaminantes Ambientales , Isópodos , Níquel , Animales , Contaminantes Ambientales/farmacocinética , Contaminantes Ambientales/toxicidad , Níquel/farmacocinética , Níquel/toxicidad , Estrés Oxidativo , Reproducción , TranscriptomaRESUMEN
The success of diffraction experiments from weakly scattering samples strongly depends on achieving an optimal signal-to-noise ratio. This is particularly important in single-particle imaging experiments where diffraction signals are typically very weak and the experiments are often accompanied by significant background scattering. A simple way to tremendously reduce background scattering by placing an aperture downstream of the sample has been developed and its application in a single-particle X-ray imaging experiment at FLASH is demonstrated. Using the concept of a post-sample aperture it was possible to reduce the background scattering levels by two orders of magnitude.
RESUMEN
We present a deterministic approach to the ptychographic retrieval of the wave at the exit surface of a specimen of condensed matter illuminated by X-rays. The method is based on the solution of an overdetermined set of linear equations, and is robust to measurement noise. The set of linear equations is efficiently solved using the conjugate gradient least-squares method implemented using fast Fourier transforms. The method is demonstrated using a data set obtained from a gold-chromium nanostructured test object. It is shown that the transmission function retrieved by this linear method is quantitatively comparable with established methods of ptychography, with a large decrease in computational time, and is thus a good candidate for real-time reconstruction.
Asunto(s)
Difracción de Rayos X/métodos , Cromo/química , Oro/química , Modelos Teóricos , Nanoestructuras/químicaRESUMEN
We examine the underlying cognitive mechanisms that govern how competitions play out over time. We used cognitive modeling to examine the dynamic effects of time remaining and relative performance (whether the person is winning or losing) on effort and strategy. In this experiment, participants completed a competitive decision-making task with varying time limits and starting scores, in a repeated-measures design. Participants were tasked with scoring more points than their computerized opponent during a certain time frame, gaining and losing points for correct and incorrect decisions, respectively. The results showed that as the competition deadline approached and as participants drew ahead of their opponent within a competition, they increased effort and became more cautious. Furthermore, the effect of relative score on effort and caution changed over the course of a competition as the deadline approached. These results highlight the importance of considering dynamics when working to understand how competitions unfold as well as the underlying cognitive mechanisms that give rise to the dynamic behavior.
RESUMEN
Nanoparticles, exhibiting functionally relevant structural heterogeneity, are at the forefront of cutting-edge research. Now, high-throughput single-particle imaging (SPI) with X-ray free-electron lasers (XFELs) creates opportunities for recovering the shape distributions of millions of particles that exhibit functionally relevant structural heterogeneity. To realize this potential, three challenges have to be overcome: (1) simultaneous parametrization of structural variability in real and reciprocal spaces; (2) efficiently inferring the latent parameters of each SPI measurement; (3) scaling up comparisons between 105 structural models and 106 XFEL-SPI measurements. Here, we describe how we overcame these three challenges to resolve the nonequilibrium shape distributions within millions of gold nanoparticles imaged at the European XFEL. These shape distributions allowed us to quantify the degree of asymmetry in these particles, discover a relatively stable "shape envelope" among nanoparticles, discern finite-size effects related to shape-controlling surfactants, and extrapolate nanoparticles' shapes to their idealized thermodynamic limit. Ultimately, these demonstrations show that XFEL SPI can help transform nanoparticle shape characterization from anecdotally interesting to statistically meaningful.
RESUMEN
We investigated the effects of two types of competition, races and tournaments (as well as an individual challenge and a do-your-best condition), on two different aspects of performance: effort and strategy. In our experiment, 100 undergraduate participants completed a simple cognitive task under four experimental conditions (in a repeated-measures design) based on different types of competitions and challenges. We used the Linear Ballistic Accumulator to quantify the effects of competition on strategy and effort. The results reveal that competition produced changes in strategy rather than effort, and that trait competitiveness had minimal impact on how people responded to competition. This suggests individuals are more likely to adjust their strategy in competitions, and the uncertainty created by different competition types influences the direction of these strategy adjustments.
Asunto(s)
Cognición , Humanos , IncertidumbreRESUMEN
Ptychographic coherent diffractive imaging (CDI) has been extensively applied using both x rays and electrons. The extension to atomic resolution has been elusive. This Letter demonstrates ptychographic electron diffractive imaging at atomic resolution, permitting identification of structure in a boron nitride helical cone at a resolution of order 1 Å, beyond that of comparative Z-contrast images. A scanning transmission electron microscope is used to create a diverging illumination in a defocused Fresnel CDI geometry, providing a robust strategy leading to a unique solution.
RESUMEN
Previous infection with Epstein-Barr virus (EBV) and infectious mononucleosis are established multiple sclerosis (MS) risk factors, and elevated serum titers of anti-EBV nuclear antigen (anti-EBNA) antibodies in healthy adults are strongly correlated with future MS risk. In this prospective study, we investigated the association between EBV neutralizing antibodies and MS risk. MS risk tended to be higher in individuals with high titers of neutralizing antibodies compared to those with low titers (relative risk [RR] = 2.2, 95% confidence interval [CI] 0.97-5.1). This association was attenuated after adjustment for anti-EBNA1 IgG Ab titers (RR = 1.4, 95% CI 0.5-3.5). This preliminary finding warrants further study in a larger population.
Asunto(s)
Anticuerpos Neutralizantes/sangre , Infecciones por Virus de Epstein-Barr/inmunología , Herpesvirus Humano 4/inmunología , Esclerosis Múltiple/inmunología , Ensayo de Inmunoadsorción Enzimática , Infecciones por Virus de Epstein-Barr/diagnóstico , Infecciones por Virus de Epstein-Barr/epidemiología , Antígenos Nucleares del Virus de Epstein-Barr/inmunología , Femenino , Humanos , Modelos Logísticos , Esclerosis Múltiple/epidemiología , Oportunidad Relativa , Estudios Prospectivos , Medición de Riesgo , Factores de Riesgo , Regulación hacia Arriba , Proteínas de la Matriz Viral/inmunologíaRESUMEN
Improvements in x-ray optics critically depend on the measurement of their optical performance. The knowledge of wavefront aberrations, for example, can be used to improve the fabrication of optical elements or to design phase correctors to compensate for these errors. At present, the characterization of such optics is made using intense x-ray sources, such as synchrotrons. However, the limited access to these facilities can substantially slow down the development process. Improvements in the brightness of lab-based x-ray micro-sources in combination with the development of new metrology methods, particularly ptychographic x-ray speckle tracking, enable characterization of x-ray optics in the lab with a precision and sensitivity not possible before. Here, we present a laboratory setup that utilizes a commercially available x-ray source and can be used to characterize different types of x-ray optics. The setup is used in our laboratory on a routine basis to characterize multilayer Laue lenses of high numerical aperture and other optical elements. This typically includes measurements of the wavefront distortions, optimum operating photon energy, and focal length of the lens. To check the sensitivity and accuracy of this laboratory setup, we compared the results to those obtained at the synchrotron and saw no significant difference. To illustrate the feedback of measurements on performance, we demonstrated the correction of the phase errors of a particular multilayer Laue lens using a 3D printed compound refractive phase plate.
RESUMEN
The European X-ray Free Electron Laser (XFEL) and Linac Coherent Light Source (LCLS) II are extremely intense sources of X-rays capable of generating Serial Femtosecond Crystallography (SFX) data at megahertz (MHz) repetition rates. Previous work has shown that it is possible to use consecutive X-ray pulses to collect diffraction patterns from individual crystals. Here, we exploit the MHz pulse structure of the European XFEL to obtain two complete datasets from the same lysozyme crystal, first hit and the second hit, before it exits the beam. The two datasets, separated by <1 µs, yield up to 2.1 Å resolution structures. Comparisons between the two structures reveal no indications of radiation damage or significant changes within the active site, consistent with the calculated dose estimates. This demonstrates MHz SFX can be used as a tool for tracking sub-microsecond structural changes in individual single crystals, a technique we refer to as multi-hit SFX.
Asunto(s)
Electrones , Rayos Láser , Cristalografía por Rayos X , Radiografía , Rayos XRESUMEN
One of the outstanding analytical problems in X-ray single-particle imaging (SPI) is the classification of structural heterogeneity, which is especially difficult given the low signal-to-noise ratios of individual patterns and the fact that even identical objects can yield patterns that vary greatly when orientation is taken into consideration. Proposed here are two methods which explicitly account for this orientation-induced variation and can robustly determine the structural landscape of a sample ensemble. The first, termed common-line principal component analysis (PCA), provides a rough classification which is essentially parameter free and can be run automatically on any SPI dataset. The second method, utilizing variation auto-encoders (VAEs), can generate 3D structures of the objects at any point in the structural landscape. Both these methods are implemented in combination with the noise-tolerant expand-maximize-compress (EMC) algorithm and its utility is demonstrated by applying it to an experimental dataset from gold nanoparticles with only a few thousand photons per pattern. Both discrete structural classes and continuous deformations are recovered. These developments diverge from previous approaches of extracting reproducible subsets of patterns from a dataset and open up the possibility of moving beyond the study of homogeneous sample sets to addressing open questions on topics such as nanocrystal growth and dynamics, as well as phase transitions which have not been externally triggered.
RESUMEN
For the first time, the structure, dimensions, and composition of the epidermis of an invasive earthworm species that has successfully colonized hostile conditions in actively volcanic soil on São Miguel (Azores) have been measured. Metal concentrations in actively volcanic (Furnas) and volcanically inactive (Fajã) soils were similar; however, Furnas soil was characterised by elevated temperature (10°C differential), relative hypoxia, extremely high CO(2) tension, and accompanying acidity. The epidermis of earthworm's resident at Fajã was approximately twice the thickness of the epidermis of conspecifics resident in Furnas soil. Reference worms transferred to Furnas soil for 14 days experienced an epidermal thinning of approximately 51%. In comparison, when Furnas earthworms were transferred to mesocosms at the relatively benign Fajã site, their epidermal thickness increased by approximately 21% over 14 days. Earthworms resident in Furnas soil had higher goblet cell counts than the residents of volcanically inactive soil on a neighbouring island (S. Maria). Transferring worms from S. Maria to mesocosms at Furnas induced a significant increase in goblet cell counts. Clearly, the active volcanic environment at Furnas poses a multifactorial stress challenge to the epigeic A. gracilis colonizer.
Asunto(s)
Monitoreo del Ambiente/métodos , Epidermis/efectos de los fármacos , Metales/toxicidad , Oligoquetos/efectos de los fármacos , Contaminantes del Suelo/toxicidad , Suelo/química , Erupciones Volcánicas , Animales , Azores , Dióxido de Carbono/metabolismo , Recuento de Células , Epidermis/metabolismo , Epidermis/ultraestructura , Concentración de Iones de Hidrógeno , Metales/análisis , Oligoquetos/metabolismo , Oligoquetos/ultraestructura , Contaminantes del Suelo/análisis , Contaminantes del Suelo/químicaRESUMEN
A phasing algorithm for macromolecular crystallography is proposed that utilizes diffraction data from multiple crystal forms - crystals of the same molecule with different unit-cell packings (different unit-cell parameters or space-group symmetries). The approach is based on the method of iterated projections, starting with no initial phase information. The practicality of the method is demonstrated by simulation using known structures that exist in multiple crystal forms, assuming some information on the molecular envelope and positional relationships between the molecules in the different unit cells. With incorporation of new or existing methods for determination of these parameters, the approach has potential as a method for ab initio phasing.
RESUMEN
In recent years, X-ray speckle-tracking techniques have emerged as viable tools for wavefront metrology and sample imaging applications. These methods are based on the measurement of near-field images. Thanks to their simple experimental setup, high angular sensitivity and compatibility with low-coherence sources, these methods have been actively developed for use with synchrotron and laboratory light sources. Not only do speckle-tracking techniques give the potential for high-resolution imaging, but they also provide rapid and robust characterization of aberrations of X-ray optical elements, focal spot profiles, and sample position and transmission properties. In order to realize these capabilities, software implementations are required that are equally rapid and robust. To address this need, a software suite has been developed for the ptychographic X-ray speckle-tracking technique, an X-ray speckle-based method suitable for highly divergent wavefields. The software suite is written in Python 3, with an OpenCL back end for GPU and multi-CPU core processing. It is accessible as a Python module, through the command line or through a graphical user interface, and is available as source code under Version 3 or later of the GNU General Public License.
RESUMEN
The deterioration of both the signal-to-noise ratio and the spatial resolution in the electron-density distribution reconstructed from diffraction intensities collected at different orientations of a sample is analysed theoretically with respect to the radiation damage to the sample and the variations in the X-ray intensities illuminating different copies of the sample. The simple analytical expressions and numerical estimates obtained for models of radiation damage and incident X-ray pulses may be helpful in planning X-ray free-electron laser (XFEL) imaging experiments and in analysis of experimental data. This approach to the analysis of partially coherent X-ray imaging configurations can potentially be used for analysis of other forms of imaging where the temporal behaviour of the sample and the incident intensity during exposure may affect the inverse problem of sample reconstruction.
RESUMEN
A data-driven method for respiratory gating in PET has recently been commercially developed. We sought to compare the performance of the algorithm with an external, device-based system for oncologic 18F-FDG PET/CT imaging. Methods: In total, 144 whole-body 18F-FDG PET/CT examinations were acquired, with a respiratory gating waveform recorded by an external, device-based respiratory gating system. In each examination, 2 of the bed positions covering the liver and lung bases were acquired with a duration of 6 min. Quiescent-period gating retaining approximately 50% of coincidences was then able to produce images with an effective duration of 3 min for these 2 bed positions, matching the other bed positions. For each examination, 4 reconstructions were performed and compared: data-driven gating (DDG) (we use the term DDG-retro to distinguish that we did not use the real-time R-threshold-based application of DDG that is available within the manufacturer's product), external device-based gating (real-time position management (RPM)-gated), no gating but using only the first 3 min of data (ungated-matched), and no gating retaining all coincidences (ungated-full). Lesions in the images were quantified and image quality scored by a radiologist who was masked to the method of data processing. Results: Compared with the other reconstruction options, DDG-retro increased the SUVmax and decreased the threshold-defined lesion volume. Compared with RPM-gated, DDG-retro gave an average increase in SUVmax of 0.66 ± 0.1 g/mL (n = 87, P < 0.0005). Although the results from the masked image evaluation were most commonly equivalent, DDG-retro was preferred over RPM-gated in 13% of examinations, whereas the opposite occurred in just 2% of examinations. This was a significant preference for DDG-retro (P = 0.008, n = 121). Liver lesions were identified in 23 examinations. Considering this subset of data, DDG-retro was ranked superior to ungated-full in 6 of 23 (26%) cases. Gated reconstruction using the external device failed in 16% of examinations, whereas DDG-retro always provided a clinically acceptable image. Conclusion: In this clinical evaluation, DDG-retro provided performance superior to that of the external device-based system. For most examinations the performance was equivalent, but DDG-retro had superior performance in 13% of examinations, leading to a significant preference overall.
Asunto(s)
Fluorodesoxiglucosa F18 , Tomografía Computarizada por Tomografía de Emisión de Positrones/métodos , Radiofármacos , Técnicas de Imagen Sincronizada Respiratorias/métodos , Algoritmos , HumanosRESUMEN
A method is presented for the measurement of the phase gradient of a wavefront by tracking the relative motion of speckles in projection holograms as a sample is scanned across the wavefront. By removing the need to obtain an undistorted reference image of the sample, this method is suitable for the metrology of highly divergent wavefields. Such wavefields allow for large magnification factors that, according to current imaging capabilities, will allow for nanoradian angular sensitivity and nanoscale sample projection imaging. Both the reconstruction algorithm and the imaging geometry are nearly identical to that of ptychography, except that the sample is placed downstream of the beam focus and that no coherent propagation is explicitly accounted for. Like other X-ray speckle tracking methods, it is robust to low-coherence X-ray sources, making it suitable for laboratory-based X-ray sources. Likewise, it is robust to errors in the registered sample positions, making it suitable for X-ray free-electron laser facilities, where beam-pointing fluctuations can be problematic for wavefront metrology. A modified form of the speckle tracking approximation is also presented, based on a second-order local expansion of the Fresnel integral. This result extends the validity of the speckle tracking approximation and may be useful for similar approaches in the field.
RESUMEN
The ever-increasing brightness of synchrotron radiation sources demands improved X-ray optics to utilize their capability for imaging and probing biological cells, nano-devices and functional matter on the nanometre scale with chemical sensitivity. Hard X-rays are ideal for high-resolution imaging and spectroscopic applications owing to their short wavelength, high penetrating power and chemical sensitivity. The penetrating power that makes X-rays useful for imaging also makes focusing them technologically challenging. Recent developments in layer deposition techniques have enabled the fabrication of a series of highly focusing X-ray lenses, known as wedged multi-layer Laue lenses. Improvements to the lens design and fabrication technique demand an accurate, robust, in situ and at-wavelength characterization method. To this end, a modified form of the speckle tracking wavefront metrology method has been developed. The ptychographic X-ray speckle tracking method is capable of operating with highly divergent wavefields. A useful by-product of this method is that it also provides high-resolution and aberration-free projection images of extended specimens. Three separate experiments using this method are reported, where the ray path angles have been resolved to within 4â nrad with an imaging resolution of 45â nm (full period). This method does not require a high degree of coherence, making it suitable for laboratory-based X-ray sources. Likewise, it is robust to errors in the registered sample positions, making it suitable for X-ray free-electron laser facilities, where beam-pointing fluctuations can be problematic for wavefront metrology.