Evaluation of long-term bond strength and selected properties of self-adhesive resin cements.

This study evaluated the shear bond strength (SBS) of self-adhesive resin cements (SARCs) to dentin and their physical-chemical properties. Five commercial SARCs were evaluated [SmartCem®2 - DENTSPLY (SC2); BisCem® - Bisco (BC); SeT PP® - SDI (SeT); Relyx U100® - 3M ESPE (U100) and YCEM® SA - Yller (YCEM)]. The SARCs were evaluated for SBS to dentin (n = 10) after 24 h, 6 months, and 12 months. The dentin demineralization caused by acidic monomers was observed by SEM, and pH-neutralization of eluate was observed for 24 h. Degree of conversion (DC), rate of polymerization (Rp), flexural strength (FS), and elastic modulus (E) were evaluated. Immediate SBS of SC2, SET, U100, and YCEM were statistically higher than that of BC (p < 0.001). After 12 months, all SARCs showed reduced SBS values and U100 showed values similar to those of SET and YCEM, and higher than those of BC and SC2 (p = 0.001). Demineralization pattern of SARCs was similar. At 24h, all SARCs showed no differences in the pH-value, except BC and U100 (p < 0.001). YCEM showed the highest Rp. U100, YCEM, and SC2 showed statistically higher FS (p<0.001) and E (p < 0.001) when compared with SET and BC. U100 and YCEM showed the best long-term bonding irrespective of the storage period. A significant reduction in SBS was found for all groups after 12 months. SBS was not shown to be correlated with physical-chemical properties, and appeared to be material-dependent. The polymerization profile suggested that an increased time of light activation, longer than that recommended by manufacturers, would be necessary to optimize DC of SARCs.

Piperonyl methacrylate: Copolymerizable coinitiator for adhesive compositions.

OBJECTIVES: This study describes the synthesis of piperonyl methacrylate (PipM) and evaluates its effect when used as coinitiator in the photoinitiated radical polymerization of experimental adhesive resins. METHODS: PipM was synthetized through an esterification reaction and characterized by FTIR and 1H NMR spectroscopy. Adhesive resins containing camphorquinone as photoinitiator and PipM or ethyl-4-dimethyl amine benzoate (EDAB) as coinitiators were formulated. Scotchbond Multipurpose (SBMP) adhesive was used as commercial reference. All materials were analyzed for polymerization kinetics, flexural strength, elastic modulus, water sorption/solubility, shear bond strength to bovine enamel and dentin, characterization of hybrid layer by scanning electron microscopy (SEM), microbiological direct contact test, and cytotoxicity. RESULTS: The adhesive with PipM presented higher degree of conversion and lower sorption/solubility when compared with other groups. Shear bond strength to enamel and dentin were similar for PipM and EDAB materials. The percentage of cellular viability was close to 100% and similar in the experimental groups and the commercial reference. CONCLUSIONS: PipM presented similar or superior performance to the tertiary amine used as control, representing a potential alternative coinitiator for photopolymerizable dental materials. CLINICAL SIGNIFICANCE: PipM could be potentially useful in the formulations of adhesive systems with enhanced chemical properties, which could mean improvement in the longevity of composite resin restorations.

Impact of hydrophilicity and length of spacer chains on the bonding of functional monomers.

OBJECTIVES: 10-Methacryloyloxy-decyl-dihydrogen-phosphate (10-MDP) is currently considered as one of the most effective functional monomers for dental bonding, this in part thanks to its long and relatively hydrophobic spacer chain, adequately separating the polymerizable from the phosphate functionalities. This study compared functional monomers with different spacer chains' length and hydrophilicity to 10-MDP on their dentin and enamel bonding performance. METHODS: Atomic absorption spectroscopy (AAS) was used to characterize the chemical interaction. Micro-tensile bond strength (µTBS) and fractographic analyses were performed after 24h and one year. Confocal micro-permeability and SEM nanoleakage assessments were also undertaken. The tested functional monomers were 2-MEP (2-carbon spacer), 10-MDP (10-carbon), 12-MDDP (12-carbon), MTEP (high hydrophilic polyether spacer chain) and CAP-P (intermediate hydrophilic ester spacer). RESULTS: AAS revealed clear differences (p<0.05) in monomer-calcium salt formation in this order: 12-MDDP=10-MDP>CAP-P>MTEP>2-MEP. The highest initial dentin µTBS was obtained using 10-MDP or 12-MDDP. After 1-year aging, a significant drop (p<0.05) in µTBS was observed for the adhesives with MTEP (enamel and dentin), 2-MEP (enamel) and CAP-P (enamel). MTEP presented the highest micro-permeability, while 2-MEP, CAP-P and MTEP showed increased nanoleakage after aging. SIGNIFICANCE: These outcomes showed that more hydrophilic and shorter spacer chains may compromise the chemical interaction with calcium and the dentin/enamel bonding performance.

Evaluation of long-term bond strength and selected properties of self-adhesive resin cements

Abstract This study evaluated the shear bond strength (SBS) of self-adhesive resin cements (SARCs) to dentin and their physical-chemical properties. Five commercial SARCs were evaluated [SmartCem®2 - DENTSPLY (SC2); BisCem® - Bisco (BC); SeT PP® − SDI (SeT); Relyx U100® - 3M ESPE (U100) and YCEM® SA - Yller (YCEM)]. The SARCs were evaluated for SBS to dentin (n = 10) after 24 h, 6 months, and 12 months. The dentin demineralization caused by acidic monomers was observed by SEM, and pH-neutralization of eluate was observed for 24 h. Degree of conversion (DC), rate of polymerization (Rp), flexural strength (FS), and elastic modulus (E) were evaluated. Immediate SBS of SC2, SET, U100, and YCEM were statistically higher than that of BC (p < 0.001). After 12 months, all SARCs showed reduced SBS values and U100 showed values similar to those of SET and YCEM, and higher than those of BC and SC2 (p = 0.001). Demineralization pattern of SARCs was similar. At 24h, all SARCs showed no differences in the pH-value, except BC and U100 (p < 0.001). YCEM showed the highest Rp. U100, YCEM, and SC2 showed statistically higher FS (p<0.001) and E (p < 0.001) when compared with SET and BC. U100 and YCEM showed the best long-term bonding irrespective of the storage period. A significant reduction in SBS was found for all groups after 12 months. SBS was not shown to be correlated with physical-chemical properties, and appeared to be material-dependent. The polymerization profile suggested that an increased time of light activation, longer than that recommended by manufacturers, would be necessary to optimize DC of SARCs.