Saccharopolyspora erythraea-catalyzed bioconversion of 6-deoxyerythronolide B analogs for production of novel erythromycins.

A method was developed for the large-scale bioconversion of novel 6-deoxyerythronolide B (6-dEB) analogs into erythromycin analogs. Erythromycin biosynthesis in Saccharopolyspora erythraea proceeds via the formation of a polyketide aglycone, 6-dEB, which is subsequently glycosylated, hydroxylated and methylated to yield the antibiotic erythromycin A. A modular polyketide synthase (PKS) directs 6-dEB synthesis using a dedicated set of active sites for the condensation of each of seven propionate units. Strategies based on genetic manipulation and precursor feeding are available for the efficient generation of novel 6-dEB analogs using a plasmid-based system in Streptomyces coelicolor. 6-dEB and 13-substituted 6-dEB analogs produced in this manner were fed to S. erythraea mutants which could not produce 6-dEB, yet retained their 6-dEB modification systems, and resulted in the generation of erythromycin A and 13-substituted erythromycin A analogs. Erythromycin B, C and D analogs were observed as intermediates of the process. Dissolved oxygen, temperature, the specific aglycone feed concentration, and pH were found to be important for obtaining a high yield of erythromycin A analogs. Cultivation conditions were identified which resulted in the efficient bioconversion of 6-dEB analogs into erythromycin A analogs, which this process demonstrated at the 100 l scale.

Rapid engineering of polyketide overproduction by gene transfer to industrially optimized strains.

Development of natural products for therapeutic use is often hindered by limited availability of material from producing organisms. The speed at which current technologies enable the cloning, sequencing, and manipulation of secondary metabolite genes for production of novel compounds has made it impractical to optimize each new organism by conventional strain improvement procedures. We have exploited the overproduction properties of two industrial organisms- Saccharopolyspora erythraea and Streptomyces fradiae, previously improved for erythromycin and tylosin production, respectively-to enhance titers of polyketides produced by genetically modified polyketide synthases (PKSs). An efficient method for delivering large PKS expression vectors into S. erythraea was achieved by insertion of a chromosomal attachment site ( attB) for phiC31-based integrating vectors. For both strains, it was discovered that only the native PKS-associated promoter was capable of sustaining high polyketide titers in that strain. Expression of PKS genes cloned from wild-type organisms in the overproduction strains resulted in high polyketide titers whereas expression of the PKS gene from the S. erythraea overproducer in heterologous hosts resulted in only normal titers. This demonstrated that the overproduction characteristics are primarily due to mutations in non-PKS genes and should therefore operate on other PKSs. Expression of genetically engineered erythromycin PKS genes resulted in production of erythromycin analogs in greatly superior quantity than obtained from previously used hosts. Further development of these hosts could bypass tedious mutagenesis and screening approaches to strain improvement and expedite development of compounds from this valuable class of natural products.

Optimizing the heterologous production of epothilone D in Myxococcus xanthus.

The heterologous production of epothilone D in Myxococcus xanthus was improved by 140-fold from an initial titer of 0.16 mg/L with the incorporation of an adsorber resin, the identification of a suitable carbon source, and the implementation of a fed-batch process. To reduce the degradation of epothilone D in the basal medium, XAD-16 (20 g/L) was added to stabilize the secreted product. This greatly facilitated its recovery and enhanced the yield by three-fold. The potential of using oils as a carbon source for cell growth and product formation was also evaluated. From a screen of various oils, methyl oleate was shown to have the greatest impact. At the optimal concentration of 7 mL/L in a batch process, the maximum cell density was increased from 0.4 g dry cell weight (DCW)/L to 2 g DCW/L. Product yield, however, depended on the presence of trace elements in the production medium. With an exogenous supplement of trace metals to the basal medium, the peak epothilone D titer was enhanced eight-fold. This finding demonstrates the significant role of metal ions in cell metabolism and in epothilone biosynthesis. To further increase the product yield, a continuous fed-batch process was used to promote a higher cell density and to maintain an extended production period. The optimized fed-batch cultures consistently yielded a cell density of 7 g DCW/L and an average production titer of 23 mg/L.