RESUMEN
Organic A'-site ligand structure plays a crucial role in the crystal growth of 2D perovskites, but the underlying mechanism has not been adequately understood. This problem is tackled by studying the influence of two isomeric A'-site ligands, linear-shaped n-butylammonium (n-BA+ ) and branched iso-butylammonium (iso-BA+ ), on 2D perovskites from precursor to device, with a combination of in situ grazing-incidence wide-angle X-ray scattering and density functional theory. It is found that branched iso-BA+ , due to the lower aggregation enthalpies, tends to form large-size clusters in the precursor solution, which can act as pre-nucleation sites to expedite the crystallization of vertically oriented 2D perovskites. Furthermore, iso-BA+ is less likely to be incorporated into the MAPbI3 lattice than n-BA+ , suppressing the formation of unwanted multi-oriented perovskites. These findings well explain the better device performance of 2D perovskite solar cells based on iso-BA+ and elucidate the fundamental mechanism of ligand structural impact on 2D perovskite crystallization.
RESUMEN
The crystallographic orientation of polycrystalline perovskites is found to be strongly correlated with their intrinsic properties; therefore, it can be used to effectively enhance the performance of perovskite-based devices. Here, a facile way of manipulating the facet orientation of polycrystalline perovskite films in a controllable manner is reported. By incorporating a cross-linkable organic ligand into the perovskite precursor solution, the crystal orientation disorder can be reduced in the resultant perovskite films to exhibit the prominent (001) orientation with a preferred stacking mode. Moreover, the as-formed low-dimensional perovskites (LDPs) between the organic ligand and the excess lead iodide can passivate the defects around the grain boundaries. Consequently, highly efficient p-i-n structured perovskite solar cells (PSCs) can be made in both rigid and flexible forms from modified perovskites to show high power conversion efficiencies (PCE) of 24.12% and 23.23%, respectively. The devices also exhibit superior long-term stability in a humid environment (with T90 > 1000 h) and under thermal stress (retaining 87% of its initial PCE after 1000 h). More importantly, the ligand enables the derived LDPs to be crosslinked (under 254 nm UV illumination) to demonstrate excellent mechanical bending durability in flexible devices.
RESUMEN
The black-to-yellow phase transition in perovskite quantum dots (QDs) is more complex than in bulk perovskites, regarding the role of surface energy. Here, with the assistance of in situ grazing-incidence wide-angle and small-angle X-ray scattering (GIWAXS/GISAXS), distinct phase behaviors of cesium lead iodide (CsPbI3 ) QD films under two different temperature profiles-instant heating-up (IHU) and slow heating-up (SHU) is investigated. The IHU process can cause the phase transition from black phase to yellow phase, while under the SHU process, the majority remains in black phase. Detailed studies and structural refinement analysis reveal that the phase transition is triggered by the removal of surface ligands, which switches the energy landscape. The lattice symmetry determines the transition rate and the coexistence black-to-yellow phase ratio. The SHU process allows longer relaxation time for a more ordered QD packing, which helps sustain the lattice symmetry and stabilizes the black phase. Therefore, one can use the lattice symmetry as a general index to monitor the CsPbI3 QD phase transition and finetune the coexistence black-to-yellow phase ratio for niche applications.
RESUMEN
BACKGROUND: Prostate cancer (PCa) is one of the common malignant tumors worldwide. MiR-183-5p has been reported involved in the initiation of human PCa, this study aimed to investigate whether miR-183-5p affects the development of prostate cancer. METHODS: In this study, we analyzed the expression of miR-183-5p in PCa patients and its correlation with clinicopathological parameters based on TCGA data portal. CCK-8, migration assay and invasion and wound-healing assay were performed to detect proliferation, migration and invasion in PCa cells. RESULTS: We found the expression of miR-183-5p was significantly increased in PCa tissues, and high expression of miR-183 was positively associated with poor prognosis of PCa patients. Over-expression of miR-183-5p promoted the migration, invasion capacities of PCa cells, whereas knockdown of miR-183-5p showed reversed function. Furthermore, luciferase reporter assay showed TET1 was identified as a direct target of miR-183-5p, which was negatively correlation with miR-183-5p expression level. Importantly, rescue experiments demonstrated TET1 over-expression could reverse miR-183-5p mimic induced-acceleration of PCa malignant progression. CONCLUSION: Our results indicated that miR-183-5p could act as a tumor promoter in PCa and it accelerated the malignant progression of PCa by directly targeting and down-regulating TET1.
Asunto(s)
MicroARNs , Neoplasias de la Próstata , Masculino , Humanos , Neoplasias de la Próstata/genética , MicroARNs/genética , Oxigenasas de Función Mixta/genética , Proteínas Proto-Oncogénicas/genéticaRESUMEN
The methylammonium (MA) and formamidinium (FA) are the most commonly used organic cations in perovskite solar cells (PSCs), whereas the impact of size and polarity differences between these two on the photovoltaic performances has been rarely revealed. Herein, we systematically investigated the phase distribution, optoelectronic and stability properties of FA-MA mixed perovskites. To identify the phase homogeneity, depth-dependent grazing-incidence wide-angle x-ray scattering measurements were employed, which demonstrates that the mixed cation perovskite possesses a FA-rich phase on the film surface and the bottom is comprised of MA-rich phase. Additionally, upon long-time illumination, a new PL peak is appeared at 778 nm, representing the generation of MA-rich phase induced by ion migration. It is worth noting that the phase splitting and inhomogeneous phase distribution would not bring any obvious detrimental effects to the photovoltaic performances and stability properties. Through judiciously tuning the cation proportion in pure-iodide perovskite, the additive-free PSCs achieve an efficiency as high as 20.7%. Furthermore, the PSCs with a broad range of FA/MA ratios show improved humidity/thermal/light stability despite the phase inhomogeneity. Therefore, the work shows that the MA and FA cations have a high compatibility in perovskite structure and the precise ratio control can further improve the performances.
RESUMEN
Passivating surface and bulk defects of perovskite films has been proven to be an effective way to minimize nonradiative recombination losses in perovskite solar cells (PVSCs). The lattice interference and perturbation of atomic periodicity at the perovskite surfaces often significantly affect the material properties and device efficiencies. By tailoring the terminal groups on the perovskite surface and modifying the surface chemical environment, the defects can be reduced to enhance the photovoltaic performance and stability of derived PVSCs. Here, we report a rationally designed bifunctional molecule, piperazinium iodide (PI), containing both R2NH and R2NH2+ groups on the same six-membered ring, behaving both as an electron donor and an electron acceptor to react with different surface-terminating ends on perovskite films. The resulting perovskite films after defect passivation show released surface residual stress, suppressed nonradiative recombination loss, and more n-type characteristics for sufficient energy transfer. Consequently, charge recombination is significantly suppressed to result in a high open-circuit voltage (VOC) of 1.17 V and a reduced VOC loss of 0.33 V. A very high power conversion efficiency (PCE) of 23.37% (with 22.75% certified) could be achieved, which is the highest value reported for inverted PVSCs. Our work reveals a very effective way of using rationally designed bifunctional molecules to simultaneously enhance the device performance and stability.
RESUMEN
The fabrication of high-quality film with large grains oriented along the direction of film thickness is important for 2D Ruddlesden-Popper perovskite-based solar cells (PVSCs). High-quality 2D BA2 MAn-1 Pbn I3n+1 (BA+ =butylammonium, MA+ =methylammonium, n=5) perovskite films were fabricated with a grain size of over 1â µm and preferential orientation growth by introducing a second spacer cation (SSC+ ) into the precursor solution. Dynamic light scattering showed that SSC+ addition can induce aggregation in the precursor solution. The precursor aggregates are favorable for the formation of large crystal grains by inducing nucleation and decreasing the nucleation sites. Applying phenylethylammonium as SSC+ , the optimized inverted planar PVSCs presented a maximum PCE of 14.09 %, which is the highest value of the 2D BA2 MAn-1 Pbn I3n+1 (n=5) PVSCs. The unsealed device shows good moisture stability by maintaining around 90 % of its initially efficiency after 1000â h exposure to air (Hr=25±5 %).
RESUMEN
We report the fused ring electron acceptor (FREA)-perovskite hybrid as a promising platform to fabricate organic-inorganic hybrid solar cells with simple preparation, high efficiency, and good stability. The FREA-perovskite hybrid films exhibit larger grain sizes and stronger crystallinity than the pristine perovskite films. Moreover, the FREA molecules can form coordination bonding with undercoordinated Pb atoms and passivate the trap states in the perovskite films. Time-resolved photoluminescence and transient absorption measurements reveal that FREA facilitates efficient electron extraction and collection. Transient photocurrent and photovoltage measurements suggest faster charge transfer and reduced charge recombination in solar cells based on FREA-perovskite hybrid films. Consequently, solar cells based on FREA-perovskite hybrid films yield a champion efficiency of 21.7% with enhanced stability, which is higher than that of the control devices based on pristine perovskite films (19.6%).
RESUMEN
Hybrid perovskite thin films are prone to producing surface vacancies during the film formation, which degrade the stability and photovoltaic performance. Passivation via post-treatment can heal these defects, but present methods are slightly destructive to the bulk of 3D perovskite due to the solvent effect, which hinders fabrication reproducibility. Herein, nondestructive surface/interface passivation using 4-fluoroaniline (FAL) is established. FAL is not only an effective antisolvent candidate for surface modification, but also a large dipole molecule (2.84 Debye) with directional field for charge separation. Density functional theory calculation reveals that the nondestructive properties are attributed to both the conjugated amine in aromatic ring and the para-fluoro-substituent. A hot vapor assisted colloidal process is employed for the post-treatment. The molecular passivation yields an ultrathin protection layer with a hydrophobic fluoro-substituent tail and thus enhances the stability and optoelectronic properties. FAL post-treated perovskite solar cell (PSC) delivers a 20.48% power conversion efficiency under ambient conditions. Micro-photoluminescence reveals that passivation activates the dark defective state at the surface and interface, delivering the impact picture of boundary on the local carriers. This work demonstrates a generic nondestructive chemical approach for improving the performance and stability of PSCs.
RESUMEN
Despite the rapid increase of efficiency, perovskite solar cells (PSCs) still face some challenges, one of which is the current-voltage hysteresis. Herein, it is reported that yttrium-doped tin dioxide (Y-SnO2 ) electron selective layer (ESL) synthesized by an in situ hydrothermal growth process at 95 °C can significantly reduce the hysteresis and improve the performance of PSCs. Comparison studies reveal two main effects of Y doping of SnO2 ESLs: (1) it promotes the formation of well-aligned and more homogeneous distribution of SnO2 nanosheet arrays (NSAs), which allows better perovskite infiltration, better contacts of perovskite with SnO2 nanosheets, and improves electron transfer from perovskite to ESL; (2) it enlarges the band gap and upshifts the band energy levels, resulting in better energy level alignment with perovskite and reduced charge recombination at NSA/perovskite interfaces. As a result, PSCs using Y-SnO2 NSA ESLs exhibit much less hysteresis and better performance compared with the cells using pristine SnO2 NSA ESLs. The champion cell using Y-SnO2 NSA ESL achieves a photovoltaic conversion efficiency of 17.29% (16.97%) when measured under reverse (forward) voltage scanning and a steady-state efficiency of 16.25%. The results suggest that low-temperature hydrothermal-synthesized Y-SnO2 NSA is a promising ESL for fabricating efficient and hysteresis-less PSC.
RESUMEN
Solution-processable perovskite-based devices are potentially very interesting because of their relatively cheap fabrication cost but outstanding optoelectronic performance. However, the solution spin-coating process involves complicated processes, including perovskite solution droplets, nucleation of perovskite, and formation of intermediate perovskite films, resulting in complicated crystallization pathways for perovskite films under annealing. Understanding and therefore controlling the fabrication process of perovskites is difficult. Recently, synchrotron radiation-based in situ grazing-incidence wide-angle X-ray scattering (GIWAXS) techniques, which possess the advantages of high collimation, high resolution, and high brightness, have enabled to bridge complicated perovskite structure information with device performance by revealing the real-time crystallization pathways of perovskites during the spin-coating process. Herein, the developments of synchrotron radiation-based in situ GIWAXS are discussed in the study of the crystallization process of perovskites, especially revealing the important crystallization mechanisms of state-of-the-art perovskite optoelectronic devices with high performance. At the end, several potential applications and challenges associated with in situ GIWAXS techniques for perovskite-based devices are highlighted.
RESUMEN
Tin-based perovskite solar cells (PSCs) are promising environmentally friendly alternatives to their lead-based counterparts, yet they currently suffer from much lower device performance. Due to variations in the chemical properties of lead (II) and tin (II) ions, similar treatments may yield distinct effects resulting from differences in underlying mechanisms. In this work, a surface treatment on tin-based perovskite is conducted with a commonly employed ligand, iso-butylammonium iodide (iso-BAI). Unlike the passivation effects previously observed in lead-based perovskites, such treatment leads to the recrystallization of the surface, driven by the higher solubility of tin-based perovskite in common solvents. By carefully designing the solvent composition, the perovskite surface is effectively modified while preserving the integrity of the bulk. The treatment led to enhanced surface crystallinity, reduced surface strain and defects, and improved charge transport. Consequently, the best-performing power conversion efficiency of FASnI3 PSCs increases from 11.8% to 14.2%. This work not only distinguishes the mechanism of surface treatments in tin-based perovskites from that of lead-based counterparts, but also underscores the critical role in designing tailor-made strategies for fabricating efficient tin-based PSCs.
RESUMEN
Lead-tin mixed perovskites are excellent photovoltaic materials that can be used in single- or multi-junction perovskite solar cells (PSCs). However, most high-performance Pb-Sn mixed PSCs reported to date are still Pb-dominant. It is highly demanding to develop environmentally friendly low-lead PSCs, but the poor film quality caused by the uncontrollable crystallization kinetics has been hindering the efficiency improvement of low-lead PSCs. Here, a vacuum-drying strategy in the two-step method to fabricate low-lead PSCs (FAPb0.3 Sn0.7 I3 ) with an impressive efficiency of 19.67% is employed. The vacuum treatment induces the formation of low crystalline Pb0.3 Sn0.7 I2 films containing less solvent, thus facilitating the subsequent FAI penetration and suppressing pinholes. Compared with the conventional one-step method, the two-step fabricated low-lead perovskite films with the vacuum-drying treatment exhibit a larger grain size, lower trap density, and weaker recombination loss, thus giving rise to a record-high efficiency near 20% with better thermal stability.
RESUMEN
Quasi-two-dimensional (2D) Pb-Sn mixed perovskites show great potential in applications of single and tandem photovoltaic devices, but they suffer from low efficiencies due to the existence of horizontal 2D phases. Here, we obtain a record high efficiency of 18.06% based on 2D ⟨n⟩ = 5 Pb-Sn mixed perovskites (iso-BA2MA4(PbxSn1-x)5I16, x = 0.7), by optimizing the crystal orientation through a regulation of the Pb/Sn ratio. We find that Sn-rich precursors give rise to a mixture of horizontal and vertical 2D phases. Interestingly, increasing the Pb content can not only entirely suppress the unwanted horizontal 2D phase in the film but also enhance the growth of vertical 2D phases, thus significantly improving the device performance and stability. It is suggested that an increase of the Pb content in the Pb-Sn mixed systems facilitates the incorporation of iso-butylammonium (iso-BA+) ligands in vertically oriented perovskites because of the reduced lattice strain and increased interaction between the organic ligands and inorganic framework. Our work sheds light on the optimal conditions for fabricating stable and efficient 2D Pb-Sn mixed perovskite solar cells.
RESUMEN
To date, the improvement of open-circuit voltage (VOC ) offers a breakthrough for the performance of perovskite solar cells (PSCs) toward their theoretical limit. Surface modification through organic ammonium halide salts (e.g., phenethylammonium ions PEA+ and phenmethylammonium ions PMA+ ) is one of the most straightforward strategies to suppress defect density, thereby leading to improved VOC . However, the mechanism underlying the high voltage remains unclear. Here, polar molecular PMA+ is applied at the interface between perovskite and hole transporting layer and a remarkably high VOC of 1.175 V is obtained which corresponds to an increase of over 100 mV in comparison to the control device. It is revealed that the equivalent passivation effect of surface dipole effectively improves the splitting of the hole quasi-Fermi level. Ultimately the combined effect of defect suppression and surface dipole equivalent passivation effect leads to an overall increase in significantly enhanced VOC . The resulted PSCs device reaches an efficiency of up to 24.10%. Contributions are identified here by the surface polar molecules to the high VOC in PSCs. A fundamental mechanism is suggested by use of polar molecules which enables further high voltage, leading ways to highly efficient perovskite-based solar cells.
RESUMEN
Inorganic CsSnI3 with low toxicity and a narrow bandgap is a promising photovoltaic material. However, the performance of CsSnI3 perovskite solar cells (PSCs) is much lower than that of Pb-based and hybrid Sn-based (e.g., CsPbX3 and CH(NH2 )2 SnX3 ) PSCs, which may be attributed to its poor film-forming property and the deep traps induced by Sn4+ . Here, a bifunctional additive carbazide (CBZ) is adapted to deposit a pinhole-free film and remove the deep traps via two-step annealing. The lone electrons of the NH2 and CO units in CBZ can coordinate with Sn2+ to form a dense film with large grains during the phase transition at 80 °C. The decomposition of CBZ can reduce Sn4+ to Sn2+ during annealing at 150 °C to remove the deep traps. Compared with the control device (4.12%), the maximum efficiency of the CsSnI3 :CBZ PSC reaches 11.21%, which is the highest efficiency of CsSnI3 PSC reported to date. A certified efficiency of 10.90% is obtained by an independent photovoltaic testing laboratory. In addition, the unsealed CsSnI3 :CBZ devices maintain initial efficiencies of ≈100%, 90%, and 80% under an inert atmosphere (60 days), standard maximum power point tracking (650 h at 65 °C), and ambient air (100 h), respectively.
RESUMEN
The interface and crystallinity of perovskite films play a decisive role in determining the device performance, which is significantly influenced by the bottom hole-transporting material (HTM) of inverted perovskite solar cells (PVSCs). Herein, a simple design strategy of polymer HTMs is reported, which can modulate the wettability and promote the anchoring by introducing pyridine units into the polyarylamine backbone, so as to realize efficient and stable inverted PVSCs. The HTM properties can be effectively modified by varying the linkage sites of pyridine units, and 3,5-linked PTAA-P1 particularly demonstrates a more regulated molecular configuration for interacting with perovskites, leading to highly crystalline perovskite films with uniform back contact and reduced defect density. Dopant-free PTAA-P1-based inverted PVSCs have realized remarkable efficiencies of 24.89% (certified value: 24.50%) for small-area (0.08 cm2 ) as well as 23.12% for large-area (1 cm2 ) devices. Moreover, the unencapsulated device maintains over 93% of its initial efficiency after 800 h of maximum power point tracking under simulated AM 1.5G illumination.
RESUMEN
Lead halide perovskite single crystals have attracted wide interest in the field of X-ray detection due to their excellent photophysical properties. However, their inherent toxicity and high thickness restrict their applications in flexible devices. In this paper, designing a micronanometer-scale X-ray detector based on all-inorganic lead-free CsAg2I3 (CAI) single crystal microbelts (MBs) has addressed the above issues. These CAI single crystal MBs can be synthesized on various substrates with high crystal quality and excellent stability. Based on their excellent characteristics of the CAI MBs, we fabricate single CAI MB devices with an Au/CAI/Au structure, which shows not only good ultraviolet photoresponse characteristics, but also excellent X-ray detection performance. The optimized CAI photodetectors exhibit a responsivity of 23.59 mA/W, a high detectivity of 1010 Jones, and a fast response speed. For X-ray detection performance, a sensitivity of up to 515.49 µC Gyair-1 cm-2 and a detection limit of as low as 14.65 µGyair s-1 are achieved with outstanding operation stability and excellent long-term stability. Furthermore, our devices also showed excellent applicability for X-ray imaging, which is promising for their use in X-ray detection and imaging. Finally, flexible X-ray detectors are fabricated by using thin CAI single-crystal MBs and demonstrate good flexibility under different bending radii and bending cycles. Our work shows the potential for developing highly sensitive flexible integrated micro/nano optoelectronic devices by using lead-free perovskite analogue single crystals.
RESUMEN
Embedding submicrocavities is an effective approach to improve the light out-coupling efficiency (LOCE) for planar perovskite light-emitting diodes (PeLEDs). In this work, we employ phenethylammonium iodide (PEAI) to trigger the Ostwald ripening for the downward recrystallization of perovskite, resulting in spontaneous formation of buried submicrocavities as light output coupler. The simulation suggests the buried submicrocavities can improve the LOCE from 26.8 to 36.2% for near-infrared light. Therefore, PeLED yields peak external quantum efficiency (EQE) increasing from 17.3% at current density of 114 mA cm-2 to 25.5% at current density of 109 mA cm-2 and a radiance increasing from 109 to 487 W sr-1 m-2 with low rolling-off. The turn-on voltage decreased from 1.25 to 1.15 V at 0.1 W sr-1 m-2. Besides, downward recrystallization process slightly reduces the trap density from 8.90 × 1015 to 7.27 × 1015 cm-3. This work provides a self-assembly method to integrate buried output coupler for boosting the performance of PeLEDs.
RESUMEN
As a member of the L1 family of neural cell molecules, close homologue of L1 (CHL1) has been proved to be downregulated in several human cancers. In the present study, we aimed to assess the expression and prognostic value of CHL1 in clear cell renal cell carcinoma (CCRCC). Immunohistochemistry was performed to detect the expression of CHL1 in tissue microarray chips. Then we compared specific clinicopathologic features in patients with different CHL1 expressions. The correlation between CHL1 expression and overall survival (OS) was evaluated by the Kaplan-Meier method and Cox regression analysis. We found that the expression of CHL1 was significantly lower in CCRCC tissues compared with adjacent normal tissues, which was correlated with TNM stage (P<0.001), Fuhrman grade (P=0.006), and LVI (P=0.004). The Kaplan-Meier survival analysis indicated that CCRCC patients with low CHL1 expression had a poorer OS rate than those with high CHL1 expression (P<0.001). Univariate and multivariate Cox regression analyses suggested that CHL1 was an independent and unfavorable prognostic factor for the OS rate of CCRCC patients. Collectively, low expression of CHL1 might predict poor OS rate of CCRCC.