Organic-Inorganic Hybrid Crystal-Assisted Etching of Nickel Foam for the Collectively Exhaustive Electrochemical Performance of Oxygen Evolution Reaction.

In this work, an organic-inorganic hybrid crystal, violet-crystal (VC), was used to etch the nickel foam (NF) to fabricate a self-standing electrode for the water oxidation reaction. The efficacy of VC-assisted etching manifests the promising electrochemical performance towards the oxygen evolution reaction (OER), requiring only ~356 and ~376 mV overpotentials to reach 50 and 100 mA cm-2 , respectively. The OER activity improvement is attributed to the collectively exhaustive effects arising from the incorporation of various elements in the NF, and the enhancement of active site density. Furthermore, the self-standing electrode is robust, exhibiting a stable OER activity after 4,000 cyclic voltammetry cycles, and ~50 h. The anodic transfer coefficients (αa ) show that the first electron transfer step is the rate-determining step on the surface of NF-VCs-1.0 (NF etched by 1 g of VCs) electrode, while the chemical step involving dissociation following the first electron transfer step is identified as the rate-limiting step in other electrodes. The lowest Tafel slope value observed in the NF-VCs-1.0 electrode indicates the high surface coverage of oxygen intermediates and more favorable OER reaction kinetics, as confirmed by high interfacial chemical capacitance and low charge transport/interfacial resistance. This work demonstrates the importance of VCs-assisted etching of NF to activate the OER, and the ability to predict reaction kinetics and rate-limiting step based on αa values, which will open new avenues to identify advanced electrocatalysts for the water oxidation reaction.

Electron Storage System Based on a Two-Way Inversion of Redox Potentials.

Molecular-level multielectron handling toward electrical storage is a worthwhile approach to solar energy harvesting. Here, a strategy which uses chemical bonds as electron reservoirs is introduced to demonstrate the new concept of "structronics" (a neologism derived from "structure" and "electronics"). Through this concept, we establish, synthesize, and thoroughly study two multicomponent "super-electrophores": 1,8-dipyridyliumnaphthalene, 2, and its N,N-bridged cyclophane-like analogue, 3. Within both of them, a covalent bond can be formed and subsequently broken electrochemically. These superelectrophores are based on two electrophoric (pyridinium) units that are, on purpose, spatially arranged by a naphthalene scaffold. A key characteristic of 2 and 3 is that they possess a LUMO that develops through space as the result of the interaction between the closely positioned electrophoric units. In the context of electron storage, this "super-LUMO" serves as an empty reservoir, which can be filled by a two-electron reduction, giving rise to an elongated C-C bond or "super-HOMO". Because of its weakened nature, this bond can undergo an electrochemically driven cleavage at a significantly more anodic-yet accessible-potential, thereby restoring the availability of the electron pair (reservoir emptying). In the representative case study of 2, an inversion of potential in both of the two-electron processes of bond formation and bond-cleavage is demonstrated. Overall, the structronic function is characterized by an electrochemical hysteresis and a chemical reversibility. This structronic superelectrophore can be viewed as the three-dimensional counterpart of benchmark methyl viologen (MV).

Ferrocene-Incorporated Cobalt Sulfide Nanoarchitecture for Superior Oxygen Evolution Reaction.

Here, ferrocene(Fc)-incorporated cobalt sulfide (Cox Sy ) nanostructures directly grown on carbon nanotube (CNT) or carbon fiber (CF) networks for electrochemical oxygen evolution reaction (OER) using a facile one-step solvothermal method are reported. The strong synergistic interaction between Fc-Cox Sy nanostructures and electrically conductive CNTs results in the superior electrocatalytic activity with a very small overpotential of ≈304 mV at 10 mA cm-2 and a low Tafel slope of 54.2 mV dec-1 in 1 m KOH electrolyte. Furthermore, the Fc-incorporated Cox Sy (FCoS) nanostructures are directly grown on the acid pretreated carbon fiber (ACF), and the resulting fabricated electrode delivers excellent OER performance with a low overpotential of ≈315 mV at 10 mA cm-2 . Such superior OER catalytic activity can be attributed to 3D Fc-Cox Sy nanoarchitectures that consist of a high concentration of vertical nanosheets with uniform distribution of nanoparticles that afford a large number of active surface areas and edge sites. Besides, the tight contact interface between ACF substrate and Fc-Cox Sy nanostructures could effectively facilitate the electron transfer rate in the OER. This study provides valuable insights for the rational design of energy storage and conversion materials by the incorporation of other transition metal into metal sulfide/oxide nanostructures utilizing metallocene.

Towards Understanding the Solvent-Dynamic Control of the Transport and Heterogeneous Electron-Transfer Processes in Ionic Liquids.

The impact of temperature-induced changes in solvent dynamics on the diffusion coefficient and standard rate constant k0 for heterogeneous electron transfer (ET) of ethylferrocene (EFc) in 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF6 ]) is investigated. The results are analysed to understand the impact of solvent-dynamic control, solute-solvent interactions and solvent friction on the transport of redox probes and k0 . Concentration dependence of the diffusion coefficient of EFc in [BMIM][PF6 ] is observed. This is attributed to the solute-induced enhancement of the structural organisation of the ionic liquid (IL), which is supported by the concentration-dependent UV/Vis absorption and photoluminescence responses of EFc/[BMIM][PF6 ] solutions. Similar values of the activation energies for mass transport and ET and a linear relationship between the diffusion coefficient and the heterogeneous ET rate is observed. The ratio between the diffusion coefficient and the heterogeneous rate constant allows a characteristic length Ld , which is temperature-independent, to be introduced. The presented results clearly establish that mass transport and heterogeneous ET of redox probes are strongly correlated in ILs. It is proposed that the apparent kinetics of heterogeneous ET reactions in ILs can be explained in terms of their impact on thermal equilibration, energy dissipation and thermal excitation of redox-active probes.

Strain-capacitance relationship in polymer actuators based on single-walled carbon nanotubes and ionic liquid gels.

We investigate the electromechanical properties of bucky-gel electrochemical actuators incorporating various amounts of single-walled carbon nanotubes and an ionic liquid electrolyte, 1-butyl-3-methylimidazolium tetrafluoroborate, that are able to convert electrochemical energy into mechanical energy. The interplay between mechanical and electrochemical effects is studied. The electromechanical responses are investigated by means of electrochemical impedance spectroscopy and bending displacement measurements. We develop a theoretical model that allows us to rationalize the electromechanical properties of the bucky-gel actuators. This model takes into account electrochemical stress due to the intercalation (de-intercalation) process, which generates the strain and bending of the actuators. We then analyze the relationship between the strain and the real part of the complex capacitance by introducing a strain-capacitance coefficient. This coefficient is related to the electrochemical stress and the amount of the ionic adsorption (desorption) at the double-layer. From a practical point of view, the determination of the strain-capacitance coefficient is helpful for characterizing and optimizing the performance of electrochemical actuators.

Surface Initiated Immobilization of Molecules Contained in an Ionic Liquid Framework.

A simple and general route for the immobilization of molecules containing ionic liquids framework was described. The proposed approach is inspired from the classical synthesis of ionic liquid and labeled surface-initiated synthesis of molecules bearing ionic liquid components. In the first step, bromide end layer was electrochemically grafted onto the electrode surface followed by its reaction with imidazole derivatives. The generated modified materials were characterized by electrochemistry and by X-ray photoelectron spectroscopy (XPS). As a result, molecule-based ionic liquids were successfully attached onto electrode material. The possibility to perform an anion-exchange reaction within the layer was demonstrated. Furthermore, the proposed surface functionalization approach was successfully performed without requiring the synthesis of any intermediate. The generated structures provide multifunctional systems containing ions, immobilized cation and mobile anion, and redox species.

Highly conductive, capacitive, flexible and soft electrodes based on a 3D graphene-nanotube-palladium hybrid and conducting polymer.

Highly conductive, capacitive and flexible electrodes are fabricated by employing 3D graphene-nanotube-palladium nanostructures and a PEDOT:PSS conducting polymer. The fabricated flexible electrodes, without any additional metallic current collectors, exhibit increased charge mobility and good mechanical properties; they also allow greater access to the electrolyte ions and hence are suitable for flexible energy storage applications.

Hybrid TiO2/Carbon quantum dots heterojunction photoanodes for solar photoelectrocatalytic wastewater treatment.

The modification of titanium dioxide (TiO2) is a strategy to maximize the utilization of sunlight. Carbon quantum dots (CQDs) are carbon nanomaterials with outstanding optical and electronic properties that are suitable for that purpose. In this work, three types of hybrid TiO2/CQD photoelectrodes were synthesized following different methods: 1) deposition of a CQD layer on top of TiO2 (labelled as TiO2-CQD); 2) deposition of a TiO2 layer on top of CQDs (labelled as CQD-TiO2) and; 3) deposition of a mixed CQD + TiO2 layer (labelled as CQD + TiO2). The photoelectrodes were investigated for the photoelectrocatalytic degradation of phenol as model pollutant under simulated solar light and TiO2-CQD showed the highest apparent reaction rate constant of kapp = 0.0117 min-1 with 40% of TOC removal in 6 h of treatment. CQDs were found to enhance photon absorption in the visible region of the electromagnetic spectrum and in turn phenol degradation by promoting the separation of photogenerated charge carriers through electron transfer via the Ti-O-C bonds formed at the TiO2-CQD interface. Finally, the performance of the TiO2-CQD photoanode was evaluated for the treatment of real wastewater from the membrane fabrication sector, confirming its photoelectrocatalytic efficiency under solar radiation with 93% of TOC removal in 8 h of treatment and kapp = 0.0058 min-1.

A Reflection on Sustainable Anode Materials for Electrochemical Chloride Oxidation.

Chloride oxidation is a key industrial electrochemical process in chlorine-based chemical production and water treatment. Over the past few decades, dimensionally stable anodes (DSAs) consisting of RuO2 - and IrO2 -based mixed-metal oxides have been successfully commercialized in the electrochemical chloride oxidation industry. For a sustainable supply of anode materials, considerable efforts both from the scientific and industrial aspects for developing earth-abundant-metal-based electrocatalysts have been made. This review first describes the history of commercial DSA fabrication and strategies to improve their efficiency and stability. Important features related to the electrocatalytic performance for chloride oxidation and reaction mechanism are then summarized. From the perspective of sustainability, recent progress in the design and fabrication of noble-metal-free anode materials, as well as methods for evaluating the industrialization of novel electrocatalysts, are highlighted. Finally, future directions for developing highly efficient and stable electrocatalysts for industrial chloride oxidation are proposed.

Estimation of activity coefficients for aqueous organic redox flow batteries: Theoretical basis and equations.

The field of aqueous organic redox flow batteries (AORFBs) has been developing fast in recent years, and many chemistries are starting to emerge as serious contenders for grid-scale storage. The industrial development of these systems would greatly benefit from accurate physics-based models, allowing to optimize battery operation and design. Many authors in the field of flow battery modeling have brought evidence that the dilute solution hypothesis (the assumption that aqueous electrolytes behave ideally) does not hold for these systems and that calculating cell voltage or chemical potentials through concentrations rather than activities, while serviceable, may become insufficient when greater accuracy is required. This article aims to provide the theoretical basis for calculating activity coefficients of aqueous organic electrolytes used in AORFBs to provide tools to predict the concentrated behavior of aqueous electrolytes, thereby improving the accuracy of physics-based models for flow batteries.

Electrochemical fabrication of highly stable redox-active nanojunctions.

Redox-gated molecular junctions were obtained starting with a relatively large gap between two electrodes, in the micrometer range, followed by electrochemical polymerization of aniline. Polyaniline (PANI) grows from the tip side until it bridges the two electrodes. The resulting junctions were characterized electrochemically by following the variation of the tip-substrate current as a function of the electrochemical gate potential for various bias voltages and by recording their I(V) characteristics. The two electrodes make contact through PANI wires, and microjunctions with conductances around 10(-3) S were obtained. On the basis of a similar setup, PANI nanojunctions with conductances between 10(-7) and 10(-8) S were made, where the current appears to be controlled by fewer than 10 oligoaniline strands. Despite the small number of strands connecting the two electrodes, the junctions are highly stable even when several successive potential sweeps are performed. Comparison of the conductance measured in the oxidized and reduced states leads to an on/off ratio of about 70-100, which is higher than that reported for a single aniline heptamer bridging two electrodes, highlighting the interest of connecting a few tens of molecules using the scanning electrochemical microscopy (SECM) configuration. In some cases, the switching of the PANI takes place in several individual conductance steps close to that obtained for a single oligoaniline. Finally, starting with a microjunction and mechanically withdrawing the tip shrinks it down to the nanometer scale and makes it possible to reach the regime where the conductance is controlled by a limited number of strands. This work presents an easy method for making redox-gated nanojunctions and for probing the conductance of a few oligoanilines despite an initially large tip-substrate gap.

Boosting Oxygen Evolution Reaction on Metallocene-based Transition Metal Sulfides Integrated with N-doped Carbon Nanostructures.

In this study, utilizing metallocene and organosulfur chelating agent, an innovative synthetic route was developed towards electrochemically activated transition metal sulfides entrapped in pyridinic nitrogen-incorporated carbon nanostructures for superior oxygen evolution reaction (OER). Most importantly, the preferential electrochemical activation process, which consisted of both anodic and cathodic pre-treatment steps, strikingly enhanced OER and long-lasting cyclic stability. The substantial increase in OER electrocatalytic activity of Ni9 S8 /Ni3 S2 -NC and Co9 S8 -NC during the activation process was mainly attributed to the increase of faradaic active site density on the catalytic layer resulting from the reconstruction of catalytic interfaces. It was also found that Fe-based metallocene [ferrocene (Fc)]-incorporation in the Co9 S8 -NC and Ni9 S8 /Ni3 S2 -NC nanostructures significantly boosted the OER activity. Thus, the combined effects of Fc-incorporation and the electrochemical activation process reduced the overpotential to about 115 and 95 mV on the Ni9 S8 /Ni3 S2 -NC and Co9 S8 -NC nanostructures to derive a current density of 10 mA cm-2 , respectively. Notably, Fc-Ni9 S8 /Ni3 S2 -NC electrocatalysts required very small overpotentials of around 222, 244, and 280 mV to acquire the current densities of 10, 20, and 50 mA cm-2 , respectively. This work opens up a new avenue for superior OER electrocatalysts by the utilization of metallocene and the preferential electrochemical activation process.

Complex Impedance Analysis on Charge Accumulation Step of Mn3O4 Nanoparticles during Water Oxidation.

The development of efficient water-oxidizing electrocatalysts is a key issue for achieving high performance in the overall water electrolysis technique. However, the complexity of multiple electron transfer processes and large activation energies have been regarded as major bottlenecks for efficient water electrolysis. Thus, complete electrochemical processes, including electron transport, charge accumulation, and chemical bond formation/dissociation, need to be analyzed for establishing a design rule for film-type electrocatalysts. In light of this, complex capacitance analysis is an effective tool for investigating the charge accumulation and dissipation processes of film-type electrocatalysts. Here, we conduct complex capacitance analysis for the Mn3O4 nanocatalyst, which exhibits superb catalytic activity for water oxidation under neutral conditions. Charge was accumulated on the catalyst surface by the change in Mn valence between Mn(II) and Mn(IV) prior to the rate-determining O-O bond forming step. Furthermore, we newly propose the dissipation ratio (D) for understanding the energy balance between charge accumulation and charge consumption for chemical O-O bond formation. From this analysis, we reveal the potential- and thickness-dependent contribution of the charge accumulation process on the overall catalytic efficiency. We think that an understanding of complex capacitance analysis could be an effective methodology for investigating the charge accumulation process on the surface of general film-type electrocatalysts.

Host-guest complexation: a convenient route for the electroreduction of diazonium salts in aqueous media and the formation of composite materials.

Electrochemical grafting of a water-insoluble diazonium salt in aqueous media onto an electrode surface was achieved by host-guest complexation. 1-(2-Bisthienyl)-4-aminobenzene (BTAB) was solubilized in a water/beta-cyclodextrin solution (beta-CD). The corresponding diazonium salt was generated in situ then electroreduced. This process leads to the attachment of bithiophene or short oligothiophene groups to the electrode surface. The modified surfaces were analyzed by cyclic voltammetry (CV), scanning electrochemical microscopy (SECM), X-ray photoelectron spectroscopy (XPS), infrared reflection absorption spectroscopy (IRRAS), and atomic force microscopy (AFM). The electrochemical investigations show that the water-based modified surface is similar to one generated in acetonitrile without beta-CD. Thus, the attached organic layer behaves like an electrochemical switch (above some threshold potential, a soluble external probe is oxidized, but the oxidized form cannot be reduced). The modified surfaces consist of grafted bisthienylbenzene (BTB) and cyclodextrins that can be removed from the surface. This procedure may be considered as a new means of creating a surface made of submicrometric holes in an organic semiconducting layer.

Giant plasmon resonance shift using poly(3,4-ethylenedioxythiophene) electrochemical switching.

Herein, we report the variation of localized surface plasmon resonance (LSPR) of gold nanoparticle (NP) arrays covered by poly(3,4-ethylenedioxythiophene) (PEDOT) as a function of the electronic state of the polymer. Giant shifts and fine-tuning of the LSPR of gold NPs surrounded by PEDOT/sodium docecyl sulfate have been achieved. The color variations of plasmonic/conducting polymer (CP) devices are given not only by changes of the optical properties of the CP upon doping but also by a close synergy of the optical properties of CP and NP. Such systems can considerably extend the field of CP-based electrochromic devices.

Ionic liquid viscosity effects on the functionalization of electrode material through the electroreduction of diazonium.

The electrochemical reduction of 4-nitrophenyl diazonium, NPD, in different ionic liquids presenting different viscosities has been investigated. The electrochemical studies show that the reduction of diazonium leading to the formation of its corresponding radical occurs whatever the viscosity of the grafting media. Following that, the presence of an organic layer attached to the electrode after electrochemical treatment was evidenced by cyclic voltammetry (CV) in acidic media thanks to the presence of nitro groups. Moreover, infrared spectroscopy (IR), X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) confirm the presence of a nitrophenyl (NP) layer attached to the electrode material. Next, the examination of the electrochemical data through the measurement of the charge, corresponding to the reduction of the attached nitrophenyl (NP) moieties, shows that the surface concentration of NP, Γ(NP), decreases when the viscosity, η, of the grafting media increases. Additionally, in the case of the more viscous ionic liquid, N-tributyl-N-methylammonium bis(trifluoromethylsulfonyl)imide [Bu(3)MeN] [NTf(2)], a cosolvent has been added leading to fine decrease of the viscosity. The IR and CV investigations of the modified electrodes demonstrate the decrease of the amount of the attached molecules when the viscosity of the grafting media increases. In addition, a correlation between Γ(NP) as function of 1/η was observed. Finally, XPS and AFM experiments lead to an estimate of the thickness of the attached layer. As a result, both methods are in perfect agreement and thicknesses of 4 and 1 nm are measured after grafting in acetonitrile and in pure ionic liquid [Bu(3)MeN] [NTf(2)], respectively. By comparison with classical solvent, the use of viscous ionic liquid for the grafting leads to a decrease in the amount of the attached molecules and conduce to the formation of thinner or less dense layer.

Recent Advances in the Development of Organic and Organometallic Redox Shuttles for Lithium-Ion Redox Flow Batteries.

In recent years, redox flow batteries (RFBs) and derivatives have attracted wide attention from academia to the industrial world because of their ability to accelerate large-grid energy storage. Although vanadium-based RFBs are commercially available, they possess a low energy and power density, which might limit their use on an industrial scale. Therefore, there is scope to improve the performance of RFBs, and this is still an open field for research and development. Herein, a combination between a conventional Li-ion battery and a redox flow battery results in a significant improvement in terms of energy and power density alongside better safety and lower cost. Currently, Li-ion redox flow batteries are becoming a well-established subdomain in the field of flow batteries. Accordingly, the design of novel redox mediators with controllable physical chemical characteristics is crucial for the application of this technology to industrial applications. This Review summarizes the recent works devoted to the development of novel redox mediators in Li-ion redox flow batteries.

Grafting oligothiophenes on surfaces by diazonium electroreduction: a step toward ultrathin junction with well-defined metal/oligomer interface.

The functionalization of electrode materials through diazonium electroreduction using a heteroaromatic compound, without phenyl groups, has been investigated for the first time. The electrochemical reduction of 2-aminoterthiophenyldiazonium cation, generated in situ, coats the electrode (glassy carbon (GC), gold or platinum) with an ultrathin organic layer, shown by X-ray photoelectron spectroscopy (XPS) of that deposited on gold to consist of terthiophene or oligothiophene. The coating is electroactive at potential close to that of terthiophene in solution. The electrochemical response of the modified GC electrode in the presence of various reversible redox couples shows that the attached layer acts as a conductive switch. It behaves as a barrier to electron transfer when the standard redox potential is below 0.5 V/SCE; in this case diode-like behavior is observed. However, for more oxidizing redox probes the layer can be considered as transparent and no barrier effect is observed. The layer deposited on a platinum ultramicroelectrode (UME) behaves similarly to that obtained on the large GC electrode. Scanning electrochemical microscopy (SECM) can be performed using this electroswitchable modified platinum UME which can act as a filter toward competitive redox exchange pathways.

Electrochemical Growth of Metallic Nanoparticles onto Immobilized Polymer Brush Ionic Liquid as a Hybrid Electrocatalyst for the Hydrogen Evolution Reaction.

Platinum and palladium are the first choice electrocatalysts to drive the hydrogen evolution reaction. In this report, surface modification was introduced as a potential approach to generate hybrid electrocatalyst. The immobilized polymer brush, poly(1-allyl-3-methylimidazolium) (PAMI), was used as a nanostructured template for guiding the electrochemical deposition of metallic nanoparticles (Pd, Pt). The intrinsic properties of the polymer brush in term of nanostructured architecture and the anions mobility within the polymer was exploited to generate a hybrid electrocatalyst. The latter was generated using two different approaches including the direct electrochemical deposition of Pd or Pt metal and the indirect approach through the anion exchange reaction followed by the electrochemical deposition under self-electrolytic conditions. The hybrid structure based on the polymer/metallic NP exhibits an enhancement of the catalytic performance toward hydrogen evolution reaction with a low Tafel slope and overpotential. Interestingly, the indirect approach leads to decrease the metal loading by two orders of magnitude, when compared to those generated in the absence of the polymeric layer, while retaining the electrocatalytic performance.