RESUMEN
Polymer flooding is drawing lots of attention because of the technical maturity in some reservoirs. The first commercial polymer flooding in China was performed in the Daqing oilfield and is one of the largest applications in the world. Some laboratory tests from Daqing researchers in China showed that the viscoelasticity of high molecular weight polymers plays a significant role in increasing displacement efficiency. Hence, encouraged by the conventional field applications and new findings on the viscoelasticity effect of polymers on residual oil saturation (ROS), some high-concentration high-molecular-weight (HCHMW) polymer-flooding field tests have been conducted. Although some field tests were well-documented, subsequent progress was seldom reported. It was recently reported that HCHMW has a limited application in Daqing, which does not agree with observations from laboratory core flooding and early field tests. However, the cause of this discrepancy is unclear. Thus, a systematic summary of polymer-flooding mechanisms and field tests in China is necessary. This paper explained why HCHMW is not widely used when considering new understandings of polymer-flooding mechanisms. Different opinions on the viscoelasticity effect of polymers on ROS reduction were critically reviewed. Other mechanisms of polymer flooding, such as wettability change and gravity stability effect, were discussed with regard to widely reported laboratory tests, which were explained in terms of the viscoelasticity effects of polymers on ROS. Recent findings from Chinese field tests were also summarized. Salt-resistance polymers (SRPs) with good economic performance using produced water to prepare polymer solutions were very economically and environmentally promising. Notable progress in SRP flooding and new amphiphilic polymer field tests in China were summarized, and lessons learned were given. Formation blockage, represented by high injection pressure and produced productivity ability, was reported in several oil fields due to misunderstanding of polymers' injectivity. Although the influence of viscoelastic polymers on reservoir conditions is unknown, the injection of very viscous polymers to displace medium-to-high viscosity oils is not recommended. This is especially important for old wells that could cause damage. This paper clarified misleading notions on polymer-flooding implementations based on theory and practices in China.
Asunto(s)
Petróleo , Polímeros , Especies Reactivas de Oxígeno , Agua , AceitesRESUMEN
Relative permeability of polymer flooding plays a very important role in oil field development. This paper aimed to measure and calculate the relative permeability curves of polymer flooding more accurately. First, viscosity variation law of polymer in porous media was studied. Rock particles of different diameters and cementing agent were used to make artificial cores and hydrophobically associating polymer solutions were prepared for experiments. Polymer solutions were injected into the cores filled with crude oil and irreducible water. In the process of polymer flooding, produced fluid was collected at different water saturations and locations of the core. Polymer solutions were separated and their viscosities were measured. With the experimental data, the viscosity variation rule of polymer transporting in porous media was explored. The result indicates that the viscosity retention rate of polymer solutions transporting in porous media has power function relationship with the water saturation and the dimensionless distance from the core inlet. Finally, the relative permeability curves of polymer flooding were measured by unsteady state method and the viscosity variation rule was applied to the calculation of the relative permeability curves.
Asunto(s)
Polímeros , Agua , Permeabilidad , Porosidad , ViscosidadRESUMEN
Surfactants can significantly improve the oil recovery of spontaneous imbibition (SI) in unconventional oil reservoirs, but mathematical modeling of surfactant SI for displacing oil in a tight matrix is challenging because of its complex mechanism. Considering the mechanisms of surfactant diffusion and adsorption, the flow equation for the SI of surfactant solution into an oil-saturated capillary is derived, and the dynamic capillary pressure and surfactant concentration during the SI process are characterized. Then, based on the pore size distribution of the pores in a tight matrix, a core-scale mathematical model for SI of surfactant solution into an oil-saturated tight matrix is developed and validated with experimental data from the literature. The results show that surfactant adsorption can increase the product of interfacial tension and the cosine of the contact angle, and the increased capillary pressure in pores leads to a faster imbibition rate. A surfactant with a high adsorption and desorption rate on the water-solid interface and diffusion ability will lead to a higher oil production rate by SI in unconventional oil reservoirs. The proposed model is beneficial for modeling the dynamic process of surfactant SI and screening suitable surfactants for enhanced oil recovery in unconventional reservoirs.
RESUMEN
Since reservoirs with permeability less than 10 mD are characterized by high injection difficulty, high-pressure drop loss, and low pore throat mobilization during the water drive process, CO2 is often used for development in actual production to reduce the injection difficulty and carbon emission simultaneously. However, microfractures are usually developed in low-permeability reservoirs, which further reduces the injection difficulty of the driving medium. At the same time, this makes the injected gas flow very fast, while the gas utilization rate is low, resulting in a low degree of recovery. This paper conducted a series of studies on the displacement effect of CO2-soluble foaming systems in low-permeability fractured reservoirs (the permeability of the core matrix is about 0.25 mD). For the two CO2-soluble blowing agents CG-1 and CG-2, the effects of the CO2 phase state, water content, and oil content on static foaming performance were first investigated; then, a more effective blowing agent was preferred for the replacement experiments according to the foaming results; and finally, the effects of the blowing agents on sealing and improving the recovery degree of a fully open fractured core were investigated at different injection rates and concentrations, and the injection parameters were optimized. The results show that CG-1 still has good foaming performance under low water volume and various oil contents and can be used in subsequent fractured core replacement experiments. After selecting the injection rate and concentration, the blowing agent can be used in subsequent fractured cores under injection conditions of 0.6 mL/min and 2.80%. In injection conditions, the foaming agent can achieve an 83.7% blocking rate and improve the extraction degree by 12.02%. The research content of this paper can provide data support for the application effect of a CO2-soluble blowing agent in a fractured core.
RESUMEN
The conventional production technique employed for low-permeability tight reservoirs exhibits limited productivity. To solve the problem, an acetate-type supercritical carbon dioxide (scCO2) thickener, PVE, which contains a large number of microporous structures, was prepared using the atom transfer radical polymerization (ATRP) method. The product exhibited an ability to decrease the minimum miscibility pressure of scCO2 during a solubility test and demonstrated a favorable extraction efficiency in a low-permeability tight core displacement test. At 15 MPa and 70 °C, PVE-scCO2 at a concentration of 0.2% exhibits effective oil recovery rates of 5.61% for the 0.25 mD core and 2.65% for the 5 mD core. The result demonstrates that the incorporation of the thickener PVE can effectively mitigate gas channeling, further improve oil displacement efficiency, and inflict minimal damage to crude oil. The mechanism of thickening was analyzed through molecular simulation. The calculated trend of thickening exhibited excellent agreement with the experimental measurement rule. The simulation results demonstrate that the contact area between the polymer and CO2 increases in direct proportion to both the number of thickener molecules and the viscosity of the system. The study presents an effective strategy for mitigating gas channeling during scCO2 flooding and has a wide application prospect.
RESUMEN
Polymer flooding has drawn more and more attention in the world for its high incremental oil recovery factor and relative low costs compared with water flooding and other chemically enhanced oil recovery techniques. However, for many oilfields, such as Daqing Oilfield, China, that have already been flooded with polymers, how to further improve recovery remains a big problem. Traditional intralayer, interlayer and plane heterogeneity studies cannot accurately characterize the remaining oil distribution after polymer flooding. To solve this problem, we established a method to quantitatively describe the reservoir's architecture. Then, the architecture elements were dissected hierarchically and the interface of each architecture level in Daqing Oilfield was identified. The distribution pattern and development potential of the remaining oil after polymer flooding under the influence of reservoir architecture was analyzed. The results show that, regarding the sedimentary process from north to south in Daqing Oilfield, the channel becomes narrower, the thickness decreases, the point bar's width increases and the thickness of the meandering river decreases. The braided bar scale becomes larger and the thickness becomes smaller in the braided river. According to the reservoir's architecture, the remaining oil was divided into four categories of plane remaining oil (abandoned channel occlusion type, interfluvial sand body occlusion type, inter-well retention type and well pattern uncontrollable type) and three types of vertical remaining oil (in-layer interlayer occlusion type, rhythm type and gravity type). About 40% of the original oil in place (OOIP) of Daqing Oilfield has not yet been produced, which indicates that there is great potential for development. This study is important for improving oil recovery in polymer-flooded reservoirs.
RESUMEN
The injection of carbon dioxide (CO2) in low-permeable reservoirs can not only mitigate the greenhouse effect on the environment, but also enhance oil and gas recovery (EOR). For numerical simulation work of this process, relative permeability can help predict the capacity for the flow of CO2 throughout the life of the reservoir, and reflect the changes induced by the injected CO2. In this paper, the experimental methods and empirical correlations to determine relative permeability are reviewed and discussed. Specifically, for a low-permeable reservoir in China, a core displacement experiment is performed for both natural and artificial low-permeable cores to study the relative permeability characteristics. The results show that for immiscible CO2 flooding, when considering the threshold pressure and gas slippage, the relative permeability decreases to some extent, and the relative permeability of oil/water does not reduce as much as that of CO2. In miscible flooding, the curves have different shapes for cores with a different permeability. By comparing the relative permeability curves under immiscible and miscible CO2 flooding, it is found that the two-phase span of miscible flooding is wider, and the relative permeability at the gas endpoint becomes larger.