Achieving High Rate and Long Cycle Performance of Na2FePO4F Cathode Through Co-Modification of Ti Doping and Carbon Coating.

Layered Na2FePO4F (NFPF) cathode material has received widespread attention due to its green nontoxicity, abundant raw materials, and low cost. However, its poor inherent electronic conductivity and sluggish sodium ion transportation seriously impede its capacity delivery and cycling stability. In this work, NFPF by Ti doping and conformal carbon layer coating via solid-state reaction is modified. The results of experimental study and density functional theory calculations reveal that Ti doping enhances intrinsic conductivity, accelerates Na-ion transport, and generates more Na-ion storage sites, and pyrolytic carbon from polyvinylpyrrolidone (PVP) uniformly coated on the NFPF surface improves the surface/interface conductivity and suppresses the side reactions. Under the combined effect of Ti doping and carbon coating, the optimized NFPF (marked as 5T-NF@C) exhibits excellent electrochemical performance, with a high capacity of 108.4 mAh g-1 at 0.2C, a considerable capacity of 80.0 mAh g-1 even at high current density of 10C, and a high capacity retention rate of 81.8% after 2000 cycles at 10C. When assembled into a full cell with a hard carbon anode, 5T-NF@C also show good applicability. This work indicates that co-modification of Ti doping and carbon coating makes NFPF achieve high rate and long cycle performance for sodium-ion batteries.

Investigations on Zr incorporation into Li3V2(PO4)3/C cathode materials for lithium ion batteries.

Li3V2(PO4)3/C (LVP/C) composites have been modified by different ways of Zr-incorporation via ultrasonic-assisted solid-state reaction. The difference in the effect on the physicochemical properties and the electrochemical performance of LVP between Zr-doping and ZrO2-coating has also been investigated. Compared with pristine LVP/C, Zr-incorporated LVP/C composites exhibit better rate capability and cycling stability. In particular, the LVP/C-Zr electrode delivers the highest initial capacity of 150.4 mA h g-1 at 10C with a capacity retention ratio of 88.4% after 100 cycles. The enhanced electrochemical performance of Zr-incorporated LVP/C samples (LVZrP/C and LVP/C-Zr) is attributed to the increased ionic conductivity and electronic conductivity, the improved stability of the LVP structure, and the decreased charge-transfer resistance.

Achieving High-Performance Na3V2(PO4)2F3 Cathode Material through a Bifunctional N-Doped Carbon Network.

Na3V2(PO4)2F3 (NVPF) is emerging as a popular cathode for sodium-ion batteries owing to its stable structure, high operating voltage, and large energy density. However, its practical application is hindered by its low conductivity. In addition, due to the loss of fluorine during synthesis, Na3V2(PO4)3 (NVP) impurity is often easily generated, resulting in a decrease in actual operating voltage. Herein, a bifunctional carbon network composed of an N-doped carbon layer and carbon bridge is constructed around NVPF particles. Through pyrolysis of polydopamine (PDA), the NVPF particles are covered in situ by an N-doped carbon layer, and the carbon bridge generated by polytetrafluoroethylene (PTFE) is also coated with N-doped carbon. Besides, PTFE also serves as a fluorine supplement to ensure that pure NVPF is obtained. As a result, the bifunctional N-doped carbon network-modified NVPF delivers a high reversible capacity (125.7 mA h g-1 at 0.2 C) and appreciable cycle stability (92.7% at 1 C over 300 cycles, and 89.8% at 10 C over 1500 cycles). When assembled into a full cell with a commercial hard carbon anode, it displays a discharge median voltage of up to 3.62 V at 0.2 C. Furthermore, it achieves a high energy density of 373.7 W h kg-1 at a power density of 461.2 W kg-1, with an excellent specific energy retention of 78.2% after 200 cycles. Therefore, this modification method is expected to be extended to other fluorine-containing materials with poor electrical conductivity.

Hollow Layered Iron-Based Prussian Blue Cathode with Reduced Defects for High-Performance Sodium-Ion Batteries.

Fe-based Prussian blue (Fe-PB) analogues have emerged as promising cathode materials for sodium-ion batteries, owing to their cost-effectiveness, high theoretical capacity, and environmental friendliness. However, their practical application is hindered by [Fe(CN)6] defects, negatively impacting capacity and cycle stability. This work reports a hollow layered Fe-PB composite material using 1,3,5-benzenetricarboxylic acid (BTA) as a chelating and etching agent by the hydrothermal method. Compared to benzoic acid, our approach significantly reduces defects and enhances the yield of Fe-PB. Notably, the hollow layered structure shortens the diffusion path of sodium ions, enhances the activity of low-spin Fe in the Fe-PB lattice, and mitigates volume changes during Na-ion insertion/extraction into/from Fe-PB. As a sodium-ion battery cathode, this hollow layered Fe-PB exhibits an impressive initial capacity of 95.9 mAh g-1 at a high current density of 1 A g-1. Even after 500 cycles, it still maintains a considerable discharge capacity of 73.1 mAh g-1, showing a significantly lower capacity decay rate (0.048%) compared to the control sample (0.089%). Moreover, the full cell with BTA-PB-1.6 as the cathode and HC as the anode provides a considerable energy density of 312.2 Wh kg-1 at a power density of 291.0 W kg-1. This research not only enhances the Na storage performance of Fe-PB but also increases the yield of products obtained by hydrothermal methods, providing some technical reference for the production of PB materials using the low-yield hydrothermal method.

High-Voltage All-Solid-State Na-Ion-Based Full Cells Enabled by All NASICON-Structured Materials.

Na super ionic conductor (NASICON)-structured materials have evolved to play many critical roles in battery systems because of their three-dimensional framework structures. Here, by coupling NASICON-structured Na3V2(PO4)2O2F cathodes and Na3V2(PO4)3 anodes, an asymmetric Na-ion-based full cell exhibits two flat voltage plateaus at about 2.3 and 1.9 V and a high capacity of 101 mA h/g. Moreover, an all-solid-state Na-ion battery has been further enabled by the concept of using all NASICON-structured materials, including cathodes, anodes, and electrolytes (Na5YSi4O12), which delivers a high output voltage. Importantly, the full cell displays high safety without using a flammable organic liquid electrolyte and superior structure stability with all NASICON-structured materials.

Treatment of Rockwood type III acromioclavicular joint dislocation using autogenous semitendinosus tendon graft and endobutton technique.

BACKGROUND: The aim of this study was to evaluate the therapeutic effect of autogenous semitendinosus graft and endobutton technique, and compare with hook plate in treatment of Rockwood type III acromioclavicular (AC) joint dislocation. METHODS: From April 2012 to April 2013, we treated 46 patients with Rockwood type III AC joint dislocation. Patients were randomly divided into two groups: Group A was treated using a hook plate and Group B with autogenous semitendinosus graft and endobutton technique. All participants were followed up for 12 months. Radiographic examinations were performed every 2 months postoperatively, and clinical evaluation was performed using the Constant-Murley score at the last follow-up. RESULTS: Results indicated that patients in Group B showed higher mean scores (90.3±5.4) than Group A (80.4±11.5) in terms of Constant-Murley score (P=0.001). Group B patients scored higher in terms of pain (P=0.002), activities (P=0.02), range of motion (P<0.001), and strength (P=0.004). In Group A, moderate pain was reported by 2 (8.7%) and mild pain by 8 (34.8%) patients. Mild pain was reported by 1 (4.3%) patient in Group B. All patients in Group B maintained complete reduction, while 2 (8.7%) patients in Group A experienced partial reduction loss. Two patients (8.7%) encountered acromial osteolysis on latest radiographs, with moderate shoulder pain and limited range of motion. CONCLUSION: Autogenous semitendinosus graft and endobutton technique showed better results compared with the hook plate method and exhibited advantages of fewer complications such as permanent pain and acromial osteolysis.

Investigation of Co-incorporated pristine and Fe-doped Li3V2(PO4)3 cathode materials for lithium-ion batteries.

Monoclinic Li3V2(PO4)3/C (LVP/C) and Li3V1.95Fe0.05(PO4)3/C (LVFP/C) composites were successfully modified by cobalt incorporation. The effects of cobalt incorporation on the structure, morphology and electrochemical performance of the LVP/C and LVFP/C composites were systematically investigated. The results show that most Co exists in the form of CoO and forms a hybrid layer with the carbon coating on the surface of the LVP and LVFP particles; moreover, a small part of Co enters into the LVP or LVFP lattices due to atomic diffusion. Compared with LVP/C and LVFP/C, Co-incorporated samples exhibit better electrochemical performance. In particular, under the common effect of doping and a hybrid layer (carbon and metal oxides) coating, the LVFP/C-Co electrode displays a prominent initial capacity of 124.7 mA h g-1 and a very low capacity fading of ∼0.04% per cycle even after 500 cycles at 20 C. This novel co-modification method with cation doping and a hybrid layer (carbon and metal oxide) coating is a highly effective way to improve the electrochemical performance and has great potential to be easily used to modify other cathode materials with poor electrical conductivity.

Continuous transarterial infusion chemotherapy with gemcitabine and 5-Fluorouracil for advanced pancreatic carcinoma.

PURPOSE: Pancreatic carcinoma is one of the most malignant tumors of the alimentary system, with relatively high incidence rates. The purpose of this study was to assess the efficacy and safety of two regimens for advanced pancreatic carcinoma: continuous transarterial infusion versus systemic venous chemotherapy with gemcitabine and 5-fluorouracil. METHODS: Of the 48 patients with advanced pancreatic carcinoma receiving chemotherapy with gemcitabine and 5-fluorouracil, 24 received the selective transarterial infusion, and 24 the systemic chemotherapy. For the continuous transarterial infusion group (experimental group), all patients received gemcitabine 1000 mg/m2,given by 30-minute transarterial infusion, on day 1 of a 4-week cycle for 2 cycles, and a dose of 600 mg/ m2 5-fluorouracil was infused on days 1~5 of a 4-week cycle for 2 cycles. For the systemic venous group (control group), gemcitabine and 5-fluorouracil were infused through a peripheral vein, a dose of 1000 mg/m2 gemcitabine being administrated over 30 min on days 1 and 8 of a 4-week cycle for 2 cycles, and a dose of 600 mg/m2 5-fluorouracil was infused on days 1~5 of a 4-week cycle for 2 cycles. The effectiveness and safety were evaluated after 2 cycles according to WHO criteria. RESULTS: The objective effective rate in transarterial group was 33.3% versus 25% in the systemic group, the difference not being significant (P=0.626). Clinical benefit rates(CBR) in the transarterial and systemic groups were 83.3% and 58.3%, respectively (P=0.014). The means and medians for survival time in transarterial group were higher than those of the systemic group (P<0.005). at the same time, the adverse effects did not significantly differ between the two groups (P>0.05). CONCLUSION: Continuous transarterial infusion chemotherapy with gemcitabine and 5-fluorouracil could improve clinical benefit rate and survival time of patients with advanced pancreatic carcinoma, compared with systemic venous chemotherapy. Since adverse effects were limited in the transarterial group, the regimen of continuous transarterial infusion chemotherapy can be used more extensively in clinical practice. A CT and MRI conventional sequence can be used for efficacy evaluation after chemotherapy in pancreatic carcinoma.