Online large volume sample staking preconcentration and separation of enantiomeric GHRH analogs by capillary electrophoresis.

A capillary electrophoresis method is proposed to analyze the four most well-known growth hormone-releasing hormone (GHRH) analogs that are misused by athletes. Dimethyl-ß-cyclodextrin used as a chiral selector allowed, for the first time, the separation of those basic peptide analogs, including enantiopeptides (sermorelin and CJC-1293) that differ by the chirality of only one amino acid. To increase the method sensitivity, electrokinetic preconcentration methods have been investigated. The large volume sample stacking with polarity switching (PS-LVSS) method with an injected sample volume corresponding to 80% of the capillary one was found superior to the sweeping in terms of signal enhancement factor (SEF). Acid and organic solvent addition to the sample (0.1 mM phosphoric acid with 30% methanol) led to a twofold signal improvement, when compared to water as a matrix. We increased capillary dimensions to provide a signal enhancement through the injection of a larger sample volume. Finally, using a combination of the optimized PS-LVSS preconcentration with the chiral capillary zone electrophoresis (CZE), the GHRH analogs were separated and limits of detection between 75 and 200 ng/mL were reached. This method was successfully applied to urine after a desalting step. An optimized C18 SPE was used for that purpose in order to provide low sample conductivity (<130 µS/cm) and preserve the efficiency of LVSS preconcentration. SEF of 640 was obtained with desalted urine spiked with sermorelin by comparison to the CZE (without preconcentration) method.

In capillary labeling and online electrophoretic separation of N-glycans from glycoproteins.

In this study, we present a new approach for in-capillary fluorescent labeling of N-glycans prior to their analysis with CE coupled with laser-induced fluorescent detection. This integrated approach allows using a CE capillary as a microreactor to perform several steps required for labeling glycans with 8-aminopyrene-1,3,6 trisulfonic acid and at the same time as a separation channel for CE of fluorescently labeled glycans. This could be achieved through careful optimization of all different steps, including sequential injections of fluorescent dye and glycan plugs, mixing by transverse diffusion of laminar flow profiles, incubation in a thermostatic zone, and finally separation and detection with CE. Such a complex sample treatment protocol for glycan labeling that is feasible thus far only in batchwise mode can now be converted into an automated and integrated protocol. Our approach was applied successfully to analyze fluorescently labeled N-linked oligosaccharides released from human immunoglobulin G and rituximab, a monoclonal antibody used for cancer treatment. We demonstrated the superiority of this in-capillary approach over the conventional in-tube protocol, with fourfold less reagent consumption and full automation without remarkable degradation of the glycan separation profile obtained by capillary electrophoresis.

Unraveling the Speciation of ß-Amyloid Peptides during the Aggregation Process by Taylor Dispersion Analysis.

Aggregation mechanisms of amyloid ß peptides depend on multiple intrinsic and extrinsic physicochemical factors (e.g., peptide chain length, truncation, peptide concentration, pH, ionic strength, temperature, metal concentration, etc.). Due to this high number of parameters, the formation of oligomers and their propensity to aggregate make the elucidation of this physiopathological mechanism a challenging task. From the analytical point of view, up to our knowledge, few techniques are able to quantify, in real time, the proportion and the size of the different soluble species during the aggregation process. This work aims at demonstrating the efficacy of the modern Taylor dispersion analysis (TDA) performed in capillaries (50 µm i.d.) to unravel the speciation of ß-amyloid peptides in low-volume peptide samples (∼100 µL) with an analysis time of ∼3 min per run. TDA was applied to study the aggregation process of Aß(1-40) and Aß(1-42) peptides at physiological pH and temperature, where more than 140 data points were generated with a total volume of ∼1 µL over the whole aggregation study (about 0.5 µg of peptides). TDA was able to give a complete and quantitative picture of the Aß speciation during the aggregation process, including the sizing of the oligomers and protofibrils, the consumption of the monomer, and the quantification of different early- and late-formed aggregated species.

Recent Electrokinetic and Microfluidic Strategies for Detection of Amyloid Beta Peptide Biomarkers: Towards Molecular Diagnosis of Alzheimer's Disease.

Among all neurodegenerative diseases, Alzheimer's Disease (AD) is the most prevalent worldwide, with a huge burden to the society and no efficient AD treatment so far. Continued efforts have been being made towards early and powerful diagnosis of AD, in the hope for a successful set of clinical trials and subsequently AD curative treatment. Towards this aim, detection and quantification of amyloid beta (Aß) peptides in cerebrospinal fluid (CSF) and other biofluids, which are established and validated biomarkers for AD, have drawn attention of the scientific community and industry over almost two decades. In this work, an overview on our major contributions over 15 years to develop different electrokinetic and microfluidic strategies for Aß peptides detection and quantification is reported. Accordingly, discussions and viewpoints on instrumental and methodological developments for microscale electrophoresis, microfluidic designs and immuno-enrichment / assays on magnetic beads in microchannels for tracing Aß peptides in CSF are given in this review.

Analytical methods of antibody surface coverage and orientation on bio-functionalized magnetic beads: application to immunocapture of TNF-α.

The use of magnetic beads bio-functionalized by antibodies (Ab) is constantly increasing with a wide range of biomedical applications. However, despite an urgent need for current methods to monitor Ab's grafting process and orientation, existing methods are still either cumbersome and/or limited. In this work, we propose a new simple and rapid analytical approach to evaluate antibody orientation and density on magnetic beads. This approach relies on the cleavage by IdeS, a highly specific protease for human immunoglobulin G (hIgG), of immobilized antibodies. The F(ab)2 and Fc fragments could be then accurately quantified by size exclusion chromatography (SEC)-coupled to fluorescent detection (FLD), and the ratio of these fragments was used to give insight on the IgG orientation at the bead surface. Four different commercially available magnetic beads, bearing carboxyl groups, tosyl groups, streptavidin, or protein G on their surface have been used in this study. Results obtained showed that this approach ensures reliable information on hIgG orientation and bead surface coverage. Protein G magnetic beads demonstrated an optimal orientation of antibodies for antigen capture (75% of accessible F(ab)2 fragment) compared to tosylactivated, carboxylated, and streptavidin ones. Capture efficiency of the different functionalized beads towards human TNF-α immunocapture, a biomarker of inflammation, has been also compared. Protein G beads provided a more efficient capture compared to other beads. In the future, this approach could be applied to any type of surface and beads to assess hIgG coverage and orientation after any type of immobilization. A rapid and simple approach to evaluate orientation and density of antibodies immobilized on magnetic beads.

Capillary Electrophoresis-Mass Spectrometry at Trial by Metabo-Ring: Effective Electrophoretic Mobility for Reproducible and Robust Compound Annotation.

Capillary zone electrophoresis-mass spectrometry (CE-MS) is a mature analytical tool for the efficient profiling of (highly) polar and ionizable compounds. However, the use of CE-MS in comparison to other separation techniques remains underrepresented in metabolomics, as this analytical approach is still perceived as technically challenging and less reproducible, notably for migration time. The latter is key for a reliable comparison of metabolic profiles and for unknown biomarker identification that is complementary to high resolution MS/MS. In this work, we present the results of a Metabo-ring trial involving 16 CE-MS platforms among 13 different laboratories spanning two continents. The goal was to assess the reproducibility and identification capability of CE-MS by employing effective electrophoretic mobility (µeff) as the key parameter in comparison to the relative migration time (RMT) approach. For this purpose, a representative cationic metabolite mixture in water, pretreated human plasma, and urine samples spiked with the same metabolite mixture were used and distributed for analysis by all laboratories. The µeff was determined for all metabolites spiked into each sample. The background electrolyte (BGE) was prepared and employed by each participating lab following the same protocol. All other parameters (capillary, interface, injection volume, voltage ramp, temperature, capillary conditioning, and rinsing procedure, etc.) were left to the discretion of the contributing laboratories. The results revealed that the reproducibility of the µeff for 20 out of the 21 model compounds was below 3.1% vs 10.9% for RMT, regardless of the huge heterogeneity in experimental conditions and platforms across the 13 laboratories. Overall, this Metabo-ring trial demonstrated that CE-MS is a viable and reproducible approach for metabolomics.

Helical γ-Peptide Foldamers as Dual Inhibitors of Amyloid-ß Peptide and Islet Amyloid Polypeptide Oligomerization and Fibrillization.

Type 2 diabetes (T2D) and Alzheimer's disease (AD) belong to the 10 deadliest diseases and are sorely lacking in effective treatments. Both pathologies are part of the degenerative disorders named amyloidoses, which involve the misfolding and the aggregation of amyloid peptides, hIAPP for T2D and Aß1-42 for AD. While hIAPP and Aß1-42 inhibitors have been essentially designed to target ß-sheet-rich structures composing the toxic amyloid oligomers and fibrils of these peptides, the strategy aiming at trapping the non-toxic monomers in their helical native conformation has been rarely explored. We report herein the first example of helical foldamers as dual inhibitors of hIAPP and Aß1-42 aggregation and able to preserve the monomeric species of both amyloid peptides. A foldamer composed of 4-amino(methyl)-1,3-thiazole-5-carboxylic acid (ATC) units, adopting a 9-helix structure reminiscent of 310 helix, was remarkable as demonstrated by biophysical assays combining thioflavin-T fluorescence, transmission electronic microscopy, capillary electrophoresis and mass spectrometry.

Evidence for different in vitro oligomerization behaviors of synthetic hIAPP obtained from different sources.

Type 2 diabetes is characterized by the aggregation of human islet amyloid polypeptide (hIAPP), from monomer to amyloid deposits that are made of insoluble fibrils. Discrepancies concerning the nature of formed species or oligomerization kinetics among reported in vitro studies on hIAPP aggregation process have been highlighted. In this work, we investigated if the sample itself could be at the origin of those observed differences. To this aim, four hIAPP samples obtained from three different sources or suppliers have been analyzed and compared by ThT fluorescence spectroscopy and by two recently developed techniques, capillary electrophoresis (CE), and ESI-IMS-QToF-MS. Lots provided by the same supplier were shown to be very similar whatever the analytical technique used to characterize them. In contrast, several critical differences could be pointed out for hIAPP provided by different suppliers. We demonstrated that in several samples, some oligomerized peptides (e.g., dimer) were already present upon reception. Purity was also different, and the proneness of the peptide solution to form fibrils in vitro within 24 h could vary considerably from one sample source to another but not from lot to lot of the same source. All those results demonstrate that the initial state of conformation, oligomerization, and quality of the hIAPP can greatly impact the aggregation kinetics, and thus the information provided by these in vitro tests. Finally, a careful selection of the peptide batch and source is mandatory to perform relevant in vitro studies on hIAPP oligomerization and to screen new molecules modulating this pathological process. Graphical abstract.

A fresh look into background electrolyte selection for capillary electrophoresis-laser induced fluorescence of peptides and proteins.

This study reports a reinvestigation of background electrolyte selection strategy for performance improvement in CE-LIF of peptides and proteins. This strategy is based on the employment of high concentrations of organic species in BGE possessing high buffer capacity and low specific conductivity in order to ensure excellent stacking preconcentration and separation resolution of fluorescently tagged peptides and proteins. Unlike universal UV detection, the use of such BGEs at high concentrations does not lead to degradation of LIF detection signals at the working excitation and emission wavelengths. At the same buffer ionic strength, pH and electric field, an "inorganic-species-free" BGE (or ISF BGE) for CE-LIF of fluorescently labeled beta amyloid peptide Aß 1-42 (a model analyte) offered a signal intensity and peak efficiency at least three-times higher than those obtained with a conventional BGE normally used for CE-LIF, while producing an electric current twice lower. Good peak performance (in terms of height and shape) was maintained when using ISF BGEs even with samples prepared in high-conductivity phosphate buffer saline matrix. The advantageous features of such BGEs used at high concentrations over conventional ones in terms of high separation resolution, improved signal intensities, tuning of EOF magnitudes and minimization of protein adsorption on an uncoated fused silica capillary are demonstrated using Alexa-488-labelled trypsin inhibitor. Such BGE selection approach was applied for investigation of separation performance for CE-LIF of ovalbumin labelled with different fluorophores.

Online Preconcentration in Capillaries by Multiple Large-Volume Sample Stacking: An Alternative to Immunoassays for Quantification of Amyloid Beta Peptides Biomarkers in Cerebrospinal Fluid.

A novel electrokinetic preconcentration approach, so-called multiple pressure-assisted large-volume sample stacking with an electroosmotic flow pump (M-PA-LVSEP), was developed to allow in-capillary enrichment and separation of analytes from unlimited sample volumes. With this approach, the inherent limitation of in-capillary electrokinetic preconcentrations to the separation capillary volume can be overcome. The M-PA-LVSEP protocol relies on repeated cycles of pressure-assisted electroosmotic pumping and injection of extremely large sample volumes for analyte stacking and sample matrix removal. This technique was developed to address the challenge of sensitive and simultaneous determination of several amyloid ß (Aß) peptides, which are biomarkers for the molecular diagnosis of Alzheimer's disease (AD). For the first time, reliable quantification of different species of fluorescently derivatized Aß peptides, that is, Aß 1-42, Aß 1-40, and Aß 1-38 down to subnanomolar ranges in cerebrospinal fluids (CSF) from AD and non-demented patients (healthy controls) was made possible without recourse to immunoassay, immunoprecipitation, or mass spectrometry approaches. Based on the stacking from a sample plug representing up to 400% of the total capillary volume, sensitive enhancement factors up to 170 could be achieved with this "antibody free" approach. Quantification limits for these Aß peptides down to 0.05 nM with capillary electrophoresis coupled with laser-induced fluorescent detection could be obtained. Excellent agreement between results from M-PA-LVSEP and the gold standard ELISA method was achieved for measurements of Aß 1-42 in CSF, with a determination correlation (r2) better than 0.993.

On-a-chip tryptic digestion of transthyretin: a step toward an integrated microfluidic system for the follow-up of familial transthyretin amyloidosis.

A microfluidic microreactor for trypsin mediated transthyretin (TTR) digestion has been developed as a step towards the elaboration of a fully integrated microdevice for the detection of a rare and disabling disease, the familial transthyretin amyloidosis (ATTR) which is related to specific TTR mutations. Therefore, an enzymatic microreactor coupled to an analytical step able to monitor the mutation of TTR on specific peptide fragments would allow an accurate monitoring of the treatment efficiency of ATTR. In this study, two types of immobilized trypsin microreactors have been investigated: a new miniaturized, microfluidic fluidized bed packed with trypsin functionalized magnetic particles (MPs), and a thiol-ene (TE) monolith-based chip. Their performances were first demonstrated with N-benzoyl-dl-arginine-4-nitroanilide hydrochloride BApNA, a low molecular weight substrate. High reaction yields (75.2%) have been reached within 0.6 min for the TE-based trypsin microreactor, while a lower yield (12.4%) was obtained for the micro-fluidized bed within a similar residence time. Transposition of the optimized conditions, developed with BApNA, to TTR digestion in the TE-based trypsin microreactor was successfully performed. We demonstrated that the TE-chip can achieve an efficient and reproducible digestion of TTR. This has been assessed by MS detection. In addition, TTR hydrolysis led to the production of a fragment of interest allowing the therapeutic follow-up of more than twenty possible ATTR mutations. High sequence coverage (90%), similar to those obtained with free trypsin, was achieved in a short time (2.4 min). Repeated experiments showed good reproducibility (RSD = 6.8%). These promising results open up the route for an innovative treatment follow-up dedicated to ATTR.

A lab-on-a-chip for monolith-based preconcentration and electrophoresis separation of phosphopeptides.

A microdevice combining online preconcentration and separation of phosphopeptides was developed in a glass microchip. An ethylene glycol methacrylate phosphate (EGMP), acrylamide (AM) and bisacrylamide (BAA) based monolith was synthesized within microchannels through a photo-driven process. Morphological investigations revealed a homogeneous monolithic structure composed of uniform nodules (∼0.8 µm), with a large pore volume (0.62 cm3 g-1) and sufficiently high specific surface area (34.1 m2 g-1). These features make the monolith particularly interesting for preconcentration purposes. Immobilization of Zr4+ ions on the phosphate groups present at the poly(EGMP-co-AM-co-BAA) monolith surface leads to immobilized metal affinity chromatography support. This monolith-Zr4+ showed a great capacity to capture phosphopeptides. Successful preconcentration and separation of a mixture of ERK2 derived peptides differing only by their phosphorylation degree and sites could be achieved with signal enhancement factors between 340 and 910 after only 7 min of preconcentration. This integrated microdevice represents a novel approach for phosphoproteomic applications.

Microscope-assisted UV-initiated preparation of well-defined porous polymer monolithic plugs in glass microchips for peptide preconcentration.

Herein, highly defined monolithic beds were prepared in glass microchips by photopolymerization of ethylene glycol methacrylate phosphate (EGMP), acrylamide, and N,N'-methylenebisacrylamide (BAA) using an epifluorescence microscope as UV-irradiation source. Such a fast and easy method allowed precise control of (i) the edge shape, (ii) the location along the microchannel, and (iii) the length of the monolithic plugs within glass microchips. The addition of hydroquinone, a polymerization inhibitor, to the prepolymerization mixture was beneficial for achieving local and robust incorporation of monoliths with sharp edges within microchannels. The monolith length was easily tuned from 160 to 400 µm through simple change in the magnification of the objective and was found to be repeatable (relative standard deviation <7.5%). Further application for on-chip monolith-assisted solid - phase extraction is demonstrated for fluorescently labeled peptide. Both binding and subsequent elution behaviors were found to fully agree with a cation-exchange mechanism in concordance with the presence of phosphate groups at the monolith surface. Graphical abstract In-chip microscope-UV-synthesis of monolithic plugs with sharp edges.

Capillary electrophoretic focusing of covalently derivatized protein induced by surfactant.

In this communication, we present a very simple strategy to focus covalently derivatized proteins for high sensitivity CE analysis by LIF detection. We demonstrated that the covalently tagged protein can be focused just by adding SDS at a concentration above the CMC in the derivatized sample. Under specific injection conditions, SDS concentration below the CMC is also sufficient to induce the focusing of the tagged protein. This method allows the quantification and detection of the covalently tagged protein in a narrow zone with an efficiency approaching 220 000 plates/m. Very good linearity was obtained for the ubiquitin in a concentration range of 2-25 µM.

A capillary zone electrophoresis method to detect conformers and dimers of antithrombin in therapeutic preparations.

Antithrombin (AT) is a human plasma glycoprotein that possesses anticoagulant and anti-inflammatory properties. However, the native (active) form of AT is unstable and undergoes conformational changes, leading to latent, cleaved, and heterodimeric forms. The presence of these alternative forms mostly inactive can highly impact the quality and therapeutic activity of pharmaceutical AT preparations. We developed a capillary zone electrophoresis method, based on a neutral polyethylene oxide-coated capillary and a buffer close to physiological conditions, enabling the separation of more than eight forms of AT. Several peaks were identified as native, latent, and heterodimeric forms. The CZE method was reproducible with intraday relative standard deviations less than 0.5 and 2% for migration times and peak areas, respectively. The method was applied to the comparison of AT preparations produced by five competitive pharmaceutical companies, and statistical tests were performed. Important differences in the proportion of each form were highlighted. In particular, one AT preparation was shown to contain a high quantity of heterodimer, and two preparations contained high quantities of latent form. In addition, one AT preparation exhibited additional forms, not yet identified.

Dyneon THV, a fluorinated thermoplastic as a novel material for microchip capillary electrophoresis.

In this work, we have investigated Dyneon THV, a fluorinated material, as a new material to afford electrokinetic separations in microfluidic devices. To overcome protein adsorption, two poly(ethylene oxide) (PEO)-based coatings have been investigated: Pluronic F127 and PEO stearate 40. The best results were obtained with the PEO stearate 40 coating which allowed decreasing the surface contact angle from 91 ± 3 to 76°± 3. With this surface treatment, a 66% reduction of the electroosmotic mobility at pH 8.0 and a marked suppression of protein adsorption were observed compared to a native Dyneon THV microchip. Finally, a separation of fluorescently labeled proteins (bovine serum albumin and trypsin inhibitor), well-known for their strong tendency to adsorb on hydrophobic surfaces, was successfully achieved in an HEPES buffer with a PEO stearate 40 treated microchip by capillary zone electrophoresis. Furthermore, we demonstrated the possibility to perform non-aqueous capillary electrophoresis analysis of hydrophobic dyes using various solvents in untreated microchips. The overall results demonstrated not only the suitability of the Dyneon THV microchip for electrokinetic separations, but also its versatility allowing different separation modes to be implemented with the same microchip material.

High-throughput identification of monoclonal antibodies after compounding by UV spectroscopy coupled to chemometrics analysis.

Monoclonal antibodies (mAbs) compounded into the hospital pharmacy are widely used nowadays. Their fast identification after compounding and just before administration to the patient is of paramount importance for quality control at the hospital. This remains challenging due to the high similarity of the structure between mAbs. Analysis of the ultraviolet spectral data of four monoclonal antibodies (cetuximab, rituximab, bevacizumab, and trastuzumab) using unsupervised principal component analysis led us to focus exclusively on the second-derivative spectra. Partial least squares-discriminant analysis (PLS-DA) applied to these data allowed us to build models for predicting which monoclonal antibody was present in a given infusion bag. The calibration of the models was obtained from a k-fold validation. A prediction set from another batch was used to demonstrate the ability of the models to predict well. PLS-DA models performed on the spectra of the region of aromatic amino acid residues presented high ability to predict mAb identity. The region corresponding to the tyrosine residue reached the highest score of good classification with 89 %. To improve the score, standard normal variate (SNV) preprocessing was applied to the spectral data. The quality of the optimized PLS-DA models was enhanced and the region from the tyrosine/tryptophan residues allowed us excellent classification (100 %) of the four mAbs according to the matrix of confusion. The sensitivity and specificity performance parameters assessed this excellent classification. The usefulness of the combination of UV second-derivative spectroscopy to multivariate analysis with SNV preprocessing demonstrated the unambiguous identification of commercially available monoclonal antibodies. Graphical abstract PLS-DA models on the spectra of the region of aromatic amino acid residues allows mAb identification with high prediction.

Capillary electrophoresis for rapid identification of monoclonal antibodies for routine application in hospital.

mAbs are widely used in cancer therapy. Their compounding, performed just before their administration to patients, is executed in a production unit of the hospital. Identification of these drugs, individually prepared in bags for infusion before patient administration, is of paramount importance to detect potential mistakes during compounding stage. A fast and reliable analytical method based on CZE combined to a cationic capillary coating (hexadimethrine bromide) was developed for identification of the most widely used compounded therapeutic for cancer therapy (bevacizumab, cetuximab, rituximab, and trastuzumab). Considering the high structural and physico-chemical similarities of these mAbs, an extensive optimization of the BGE composition has been performed. The addition of perchlorate ions and polysorbate in the BGE greatly increased the resolution. To validate the method, an internal standard was used and the relative migration times (RTm) were estimated. Very satisfactory RSDs of the RTm for rituximab (0.76%), cetuximab (0.46%), bevacizumab (0.31%), and trastuzumab (0.60%) were obtained. The intraday and interday RSD of the method were less than 0.32 and 1.3%, respectively for RTm. Significant differences between theses RTms have been demonstrated allowing mAbs identification. Finally, accurate mAbs identification has been demonstrated by a blind test.

Supramolecular Organization and siRNA Binding of Hyaluronic Acid-Coated Lipoplexes for Targeted Delivery to the CD44 Receptor.

The dynamics of the formation of siRNA-lipoplexes coated with hyaluronic acid (HA) and the parameters influencing their supramolecular organization were studied. The insertion of a HA-dioleylphosphatidylethanolamine (DOPE) conjugate in the liposome structure as well as subsequent complexation with siRNA increased the liposome size. Lipoplexes were around 110 nm at high ± charge ratios with a zeta potential around +50 mV and around 230 nm at low ± ratios, with a zeta potential that decreased to negative values, reaching -45 mV. The addition of the conjugate did not compromise siRNA binding to liposomes, although these nucleic acids induced a displacement of part of the HA-DOPE conjugate upon lipoplex formation, as confirmed by capillary electrophoresis. Isothermal titration calorimetry, X-ray diffraction studies, and cryo-TEM microscopy demonstrated that in addition to electrostatic interactions with siRNA a rearrangement of the lipid bilayers takes place, resulting in condensed oligolamellar vesicles. This phenomenon is dependent on the number of siRNA molecules and the degree of modification with HA. Finally, the suitable positioning of HA on the lipoplex surface and its ability to bind specifically to the CD44 receptors in a concentration-dependent manner was demonstrated by surface plasmon resonance analysis.