RESUMEN
The exfoliation of graphite to graphene nanoplatelets (GnP) in a molten salt medium is investigated in this study. It is shown that this mechanical force-free process yielded a large-sized GnP product (>15 microns) with a low defect density. The effect of the surface tension of the molten salt on graphite exfoliation efficiency was investigated for a series of alkali chloride salts (CsCl, KCl, NaCl and eutectic NaCl-KCl) at 850 °C. It was demonstrated that the produced GnP could be completely and easily separated from the salt. Molten salt with the lowest value of surface tension (CsCl) displayed the highest wettability of the graphitic layers and hence facilitated total exfoliation of the graphite to GnP. The exfoliation of graphite in molten salts is applicable in the thermal energy storage field, as well as in exfoliation of other layered materials. Herein, it is demonstrated that the thermal conductivity of the GnP-CsCl composite is enhanced by â¼300% compared to the neat salt.
RESUMEN
Molten salt synthesis (MSS) of complex oxides is generally investigated by characterization of the product phases with no insight into evolution of particle morphology. In this work, LaFeO3 and LaMnO3 MSS was investigated in KF-KCl and LiCl-KCl at 850 °C using a "feeding-and-sampling" procedure. By feeding the oxide reagents into a molten salt, the reaction starting point was clearly defined, while subsequent sampling of the melt provided means for tracking the phase composition along with the shape and size of product particles during MSS. Samples taken just after 1 min contained perovskite particles along with reagents and intermediates, which were consumed over time to yield a pure product within 10-30 min. The shape and size of perovskite particles sampled at different times during MSS were virtually unchanged, revealing a lack of notable growth. The observed fast MSS along with prevailing nucleation provided means to control perovskite particle size by varying the extent of reagent dissolution. Thus, increasing the salt/reagent ratio (from 10:1 to 25:1) strikingly reduced the duration required to obtain a pure product, along with decreasing the size of product particles (from 0.5-1.5 µm to 80-200 nm). Furthermore, performing MSS in KF-KCl, which exhibits greater oxide solubility compared to LiCl-KCl, resulted in a shorter duration and smaller perovskite particles (80-200 nm and 0.6-2.0 µm, respectively). This insight into perovskite formation and growth during MSS and its kinetics provides valuable guidelines for tuning MSS conditions to better control synthesis duration and particle size.
RESUMEN
LaMnO3 perovskite was successfully synthesized in molten chlorides. In order to explore the effect of the molten salt type, NaCl-KCl and LiCl-KCl eutectic mixtures were employed as a liquid medium for the perovskite formation process. The synthesis included heating the La-nitrate, Mn-nitrate and chlorides mixture to above the melting point of the corresponding chlorides. This procedure yielded a LaMnO3 phase integrated in the fused chloride matrix. Washing with water removed the salts completely, yielding pure LaMnO3 perovskite crystals. The synthesis without molten salt at 800 °C yielded several by-products in addition to the LaMnO3 phase, while with LiCl-KCl the pure perovskite phase was obtained at temperatures as low as 600 °C. Variation of temperature in the range 600-800 °C for LiCl-KCl and 700-800 °C for NaCl-KCl had no significant effect either on the morphology or on the particle size of the product. On the other hand, the effect of the molten salt type on the morphology and size of perovskite particles was remarkable. The synthesis in NaCl-KCl resulted in sub-micron LaMnO3 particles with shapes that range from truncated hexahedrons to spheres, while in LiCl-KCl mostly cubic particles of up to 2-microns were obtained. The effect of the molten salt type on LaMnO3 perovskite formation is explained based on the nucleation and crystal growth model and difference in the melting point of eutectic mixtures.
RESUMEN
Highly dispersed Pt nanoparticles were incorporated in CeO2 nanopowders by an ultrasound-assisted reduction procedure. The activity of the Pt/CeO2 catalysts was studied in the reaction of the ethyl acetate combustion, and complete conversion was achieved at low temperature. It was demonstrated that the higher dispersion of the CeO2 support, the better the performance of the Pt/CeO2 catalysts. The catalysts were characterized by XRD, TEM, HRTEM, EDX, BET, and XPS. The homogeneous incorporation of 2-4 nm Pt nanoparticles into the interparticle distance of the CeO2 nanopowders was demonstrated. The advantage of the sonochemical method for catalyst preparation, in comparison with the traditional incipient wetness impregnation, was explained as the result of the homogeneity and better dispersion of the active metal phase obtained by ultrasound irradiation.